The C-Sky platform code is not a clock provider, and just needs to call
of_clk_init().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
This is required for clone3 which passes the TLS value through a
struct rather than a register.
Cc: Amanieu d'Antras <amanieu@gmail.com>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
We should give some necessary check for initrd just like other
architectures and it seems that setup_initrd() could be a common
code for all architectures.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
If we use a non-ipi-support interrupt controller, it will cause panic here.
We should let cpu up and work with CONFIG_SMP, when we use a non-ipi intc.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
In the past, we didn't care about kernel sp when saving pt_reg. But in some
cases, we still need pt_reg->usp to represent the kernel stack before enter
exception.
For cmpxhg in atomic.S, we need save and restore usp for above.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
After fixaddr_init is separated from highmem, we could use tcm
without highmem selected. (610 (abiv1) don't support highmem,
but it could use tcm now.)
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
The implementation are not only used by TCM but also used by sram on
SOC bus. It follow existed linux tcm software interface, so that old
tcm application codes could be re-used directly.
Software interface list in asm/tcm.h:
- Variables/Const: __tcmdata, __tcmconst
- Functions: __tcmfunc, __tcmlocalfunc
- Malloc/Free: tcm_alloc, tcm_free
In linux menuconfig:
- Choose a TCM contain instrctions + data or separated in ITCM/DTCM.
- Determine TCM_BASE (DTCM_BASE) in phyiscal address.
- Determine size of TCM or ITCM(DTCM) in page counts.
Here is hello tcm example from Documentation/arm/tcm.rst which could
be directly used:
/* Uninitialized data */
static u32 __tcmdata tcmvar;
/* Initialized data */
static u32 __tcmdata tcmassigned = 0x2BADBABEU;
/* Constant */
static const u32 __tcmconst tcmconst = 0xCAFEBABEU;
static void __tcmlocalfunc tcm_to_tcm(void)
{
int i;
for (i = 0; i < 100; i++)
tcmvar ++;
}
static void __tcmfunc hello_tcm(void)
{
/* Some abstract code that runs in ITCM */
int i;
for (i = 0; i < 100; i++) {
tcmvar ++;
}
tcm_to_tcm();
}
static void __init test_tcm(void)
{
u32 *tcmem;
int i;
hello_tcm();
printk("Hello TCM executed from ITCM RAM\n");
printk("TCM variable from testrun: %u @ %p\n", tcmvar, &tcmvar);
tcmvar = 0xDEADBEEFU;
printk("TCM variable: 0x%x @ %p\n", tcmvar, &tcmvar);
printk("TCM assigned variable: 0x%x @ %p\n", tcmassigned, &tcmassigned);
printk("TCM constant: 0x%x @ %p\n", tcmconst, &tcmconst);
/* Allocate some TCM memory from the pool */
tcmem = tcm_alloc(20);
if (tcmem) {
printk("TCM Allocated 20 bytes of TCM @ %p\n", tcmem);
tcmem[0] = 0xDEADBEEFU;
tcmem[1] = 0x2BADBABEU;
tcmem[2] = 0xCAFEBABEU;
tcmem[3] = 0xDEADBEEFU;
tcmem[4] = 0x2BADBABEU;
for (i = 0; i < 5; i++)
printk("TCM tcmem[%d] = %08x\n", i, tcmem[i]);
tcm_free(tcmem, 20);
}
}
TODO:
- Separate fixup mapping from highmem
- Support abiv1
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
This is a basic -fstack-protector support without per-task canary
switching. The protector will report something like when stack
corruption is detected:
It's tested with strcpy local array overflow in sys_kill and get:
stack-protector: Kernel stack is corrupted in: sys_kill+0x23c/0x23c
TODO:
- Support task switch for different cannary
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFRBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn2VACgkge7vTeUNeZFc+6F4NWphAQ5tCQAoK/MMbU6
0O8ef7PjFwCU4s227UTv
=6m40
-----END PGP SIGNATURE-----
Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
con_init in tty/vt.c will now set conswitchp to dummy_con if it's unset.
Drop it from arch setup code.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20191218214506.49252-9-nivedita@alum.mit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the entry code over to use CONFIG_PREEMPTION.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Guo Ren <guoren@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20191015191821.11479-7-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/csky/kernel/perf_event.c:1340:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.
Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>
This round of csky subsystem gives two features (ASID algorithm update,
Perf pmu record support) and some fixups.
Feature:
- csky: Revert mmu ASID mechanism
- csky: Add new asid lib code from arm
- csky: Use generic asid algorithm to implement switch_mm
- csky: Improve tlb operation with help of asid
- csky: Init pmu as a device
- csky: Add count-width property for csky pmu
- csky: Add pmu interrupt support
- csky: Fix perf record in kernel/user space
- dt-bindings: csky: Add csky PMU bindings
Fixup:
- csky: Fixup no panic in kernel for some traps
- csky: Fixup some error count in 810 & 860.
- csky: Fixup abiv1 memset error
CI-Tested: https://gitlab.com/c-sky/buildroot/pipelines/68656845
-----BEGIN PGP SIGNATURE-----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=PbF1
-----END PGP SIGNATURE-----
Merge tag 'csky-for-linus-5.3-rc1' of git://github.com/c-sky/csky-linux
Pull arch/csky pupdates from Guo Ren:
"This round of csky subsystem gives two features (ASID algorithm
update, Perf pmu record support) and some fixups.
ASID updates:
- Revert mmu ASID mechanism
- Add new asid lib code from arm
- Use generic asid algorithm to implement switch_mm
- Improve tlb operation with help of asid
Perf pmu record support:
- Init pmu as a device
- Add count-width property for csky pmu
- Add pmu interrupt support
- Fix perf record in kernel/user space
- dt-bindings: Add csky PMU bindings
Fixes:
- Fixup no panic in kernel for some traps
- Fixup some error count in 810 & 860.
- Fixup abiv1 memset error"
* tag 'csky-for-linus-5.3-rc1' of git://github.com/c-sky/csky-linux:
csky: Fixup abiv1 memset error
csky: Improve tlb operation with help of asid
csky: Use generic asid algorithm to implement switch_mm
csky: Add new asid lib code from arm
csky: Revert mmu ASID mechanism
dt-bindings: csky: Add csky PMU bindings
dt-bindings: interrupt-controller: Update csky mpintc
csky: Fixup some error count in 810 & 860.
csky: Fix perf record in kernel/user space
csky: Add pmu interrupt support
csky: Add count-width property for csky pmu
csky: Init pmu as a device
csky: Fixup no panic in kernel for some traps
csky: Select intc & timer drivers
Current C-SKY ASID mechanism is from mips and it doesn't work well
with multi-cores. ASID per core mechanism is not suitable for C-SKY
SMP tlb maintain operations, eg: tlbi.vas need share the same asid
in all processors and it'll invalid the tlb entry in all cores with
the same asid.
This patch is prepare for new ASID mechanism.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
CK810 pmu only support event with index 0-8 and 0xd; CK860 only
support event 1~4, 0xa~0x1b. So do not register unsupport event
to hardware cache event, which may leader to unknown behavior.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
csky_pmu_event_init is called several times during the perf record
initialzation. After configure the event counter in either kernel
space or user space, csky_pmu_event_init is called twice with no
attr specified. Configuration will be overwritten with sampling in
both kernel space and user space. --all-kernel/--all-user is
useless without this patch applied.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
This patch add interrupt request and handler for csky pmu.
perf can record on hardware event with this patch applied.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
The csky pmu counter may have different io width. When the counter is
smaller then 64 bits and counter value is smaller than the old value, it
will result to a extremely large delta value. So the sampled value should
be extend to 64 bits to avoid this, the extension bits base on the
count-width property from dts.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
This patch change the csky pmu initialization from arch init to
device init. The pmu can be configued with information from
device tree(pmu device name, irq number and etc.).
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
These traps couldn't be hanppen in kernel and we must panic there not
send a signal to userspace.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
The struct rt_sigframe is also defined in libgcc/config/csky/linux-unwind.h
of gcc. Although there is no use for the first three word space, we must
keep them the same with linux-unwind.h for member position.
The BUG is found in glibc test with the tst-cancel02.
The BUG is from commit:bf2416829362 of linux-5.2-rc1 merge window.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
As synchronous exceptions really only make sense against the current
task (otherwise how are you synchronous) remove the task parameter
from from force_sig_fault to make it explicit that is what is going
on.
The two known exceptions that deliver a synchronous exception to a
stopped ptraced task have already been changed to
force_sig_fault_to_task.
The callers have been changed with the following emacs regular expression
(with obvious variations on the architectures that take more arguments)
to avoid typos:
force_sig_fault[(]\([^,]+\)[,]\([^,]+\)[,]\([^,]+\)[,]\W+current[)]
->
force_sig_fault(\1,\2,\3)
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
All of the remaining callers pass current into force_sig so
remove the task parameter to make this obvious and to make
misuse more difficult in the future.
This also makes it clear force_sig passes current into force_sig_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tracehook_report_syscall_entry's return value is
__must_check attribute. We should add return processing flow in
ptrace.c and set the syscall number to -1 when failed just like
riscv's.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
This patch implements the perf registers sampling and validation API
for csky arch. The valid registers and their register ID are defined in
perf_regs.h. Perf tool can backtrace in userspace with unwind library
and the registers/user stack dump support.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
The name of phys_offset is so common for global export and it may
conflict with some local name. So change phys_offset to va_pa_offset
which also used by riscv.
Also use __pa() and __va() instead of using phys_offset directly.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Modify SETUP_MMU macro to fit on both MMU-on or MMU-off enviornment
and vmlinux could bootup from MMU off enviornment for some cases.
Unify the style of _start and _start_smp_secondary in head.S to make
head.S looks more concise and easy to understand.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Before this patch csky-linux need CONFIG_RAM_BASE to determine start
physical address. Now we use phys_offset variable to replace the macro
of PHYS_OFFSET and we setup phys_offset with real physical address which
is determined during startup in head.S.
With this patch we needn't re-compile kernel for different start
physical address. ie: 0x0 / 0xc0000000 start physical address could use
the same vmlinux, be care different start address must be 512MB aligned.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Linux kernel has provided some apis for arch signal's implementation.
For example:
restore_saved_sigmask()
set_current_blocked()
restore_altstack()
But in last version of csky signal.c didn't use them and some codes are
confusing, so reconstruct signal.c with reference to riscv's code.
Now csky signal.c implementation are very close to riscv and we can
get the following benefits:
- Clear code structure
- The signal code of riscv and csky can be reviewed together
- Promoting the unification of arch's signal implementation
Also modified the related code in entry.S
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
We could use regs->sr 16-24 bits to detect syscall: VEC_TRAP0 and
r11_sig is no necessary for current implementation.
In this patch, we implement the in_syscall and forget_syscall which are
inspired from arm & nds32, but csky pt_regs has no syscall_num element
and we just set zero to regs->sr's vector-bits-field instead.
For ret_from_fork, current task was forked from parent which is in syscall
progress and its regs->sr has been already setted with VEC_TRAP0. See:
arch/csky/kernel/process.c: copy_thread()
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Previous syscall_trace implementation couldn't support AUDITSYSCALL and
SYSCALL_TRACEPOINTS. Now we redesign it to support audit_syscall
and syscall_tracepoints just like other archs'.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Dmitry V. Levin <ldv@altlinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
This patch add support for perf callchain sampling on csky platform.
As fp is used to unwind the stack, the program being sampled and the
C library need to be compiled with -mbacktrace for user callchains,
kernel callchains require CONFIG_STACKTRACE = y.
Changelog:
- Coding convention with Christoph's advice for riscv's.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Christoph Hellwig <hch@infradead.org>
Support dynamic ftrace including dynamic graph tracer. Gcc-csky with -pg
will produce call site in every function prologue and we can use these
call site to hook trace function.
gcc with -pg origin call site:
push lr
jbsr _mcount
nop32
nop32
If the (callee - caller)'s offset is in range of bsr instruction, we'll
modify code with:
push lr
bsr _mcount
nop32
nop32
Else if the (callee - caller)'s offset is out of bsr instrunction, we'll
modify code with:
push lr
movih r26, ...
ori r26, ...
jsr r26
(r26 is reserved for jsr link reg in csky abiv2 spec.)
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
When STACKTRACE is enabled, we must pass fp as stack for unwind,
otherwise random value in stack will casue a dead loop.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Lu Baoquan <lu.baoquan@intellif.com>
Use task_stack_page instead of p->stack to get stack. Follow the coding
convention style. Also for init_stack, the same with other archs.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
The bug is from commit 2054f4af19 ("csky: bugfix gdb coredump error.")
We change the ELF_NGREG to ELF_NGREG - 2 to fit gdb&gcc define, but forgot
modify ptrace regset.
Now coredump use ELF_NRGEG to parse GPRs and ptrace use pt_regs_regset, so
there are two different reg_sets for userspace.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
This bug is from commit f553aa1c13 ("csky: fixup relocation error with
807 & 860").
I forgot to compile with 810 for that patch.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
810 doesn't support jsri instruction and csky-as will leave
jsri + nop for relocation. Module-probe need replace them with
lrw + jsr.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Hui Kai <huikai@acoinfo.com>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
