The drmm_encoder_alloc() function returns error pointers. It never
returns NULL. Fix the check accordingly.
Fixes: 7a1adbd239 ("drm: rcar-du: Use drmm_encoder_alloc() to manage encoder")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DORCR register controls the routing of clocks and data between DU
channels within a group. For groups that contain a single channel,
there's no routing option to control, and some fields of the register
are then reserved. On Gen2 those reserved fields are documented as
required to be set to 0, while on Gen3 and newer the PG1T, DK1S and PG1D
reserved fields must be set to 1.
The DU driver initializes the DORCR register in rcar_du_group_setup(),
where it ignores the PG1T, DK1S and PG1D, and then configures those
fields to the correct value in rcar_du_group_set_routing(). This hasn't
been shown to cause any issue, but prevents certifying that the driver
complies with the documentation in safety-critical use cases.
As there is no reasonable change that the documentation will be updated
to clarify that those reserved fields can be written to 0 temporarily
before starting the hardware, make sure that the registers are always
set to valid values.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The DORCR fields were documented in the R-Car H1 datasheet with 1-based
named, and then got renamed to 0-based in Gen2. The 0-based names are
used for Gen3 and Gen4, making H1 an outlier. Rename the field macros to
make them 0-based, in order to increase readability of the code when
comparing it with the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
When the input to a DU channel comes from a VSP, the DU doesn't perform
any blending operation. Select XRGB8888 instead of ARGB8888 to ensure
that the corresponding registers don't get written with invalid values.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The ESCR and OTAR registers are not present in all DU channels on Gen3
SoCs. ESCR only exists in channels that can be routed to an LVDS or
DPAD, and OTAR in channels that can be routed to a DPAD. Skip writing
those registers for other channels. This replaces the DU gen check, as
Gen4 doesn't have LVDS or DPAD outputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
On R-Car D3 and E3, the LVDS encoder provides the dot (pixel) clock to
the DU, regardless of whether the LVDS output is used or not. When using
the DPAD (RGB) output, the DU driver thus enables and disables the LVDS
PLL manually, while when using the LVDS output, it lets the LVDS bridge
driver handle the PLL configuration internally as part of the atomic
enable and disable operations.
This causes an issue when using the LVDS output. As bridges are disabled
before CRTCs, the current implementation violates the enable/disable
sequences documented in the hardware datasheet, which requires the dot
clock to be enabled before the CRTC is started and disabled after it
gets stopped.
Fix the problem by enabling/disabling the LVDS PLL manually from the DU
regardless of which output is used, and skipping the PLL handling in the
LVDS bridge atomic enable and disable operations.
This is however not enough. Disabling the LVDS encoder while leaving the
PLL on still results in a vertical blanking wait timeout when disabling
the DU. Investigation showed that the culprit is the LVEN bit. For an
unclear reason, clearing the bit when disabling the LVDS encoder blocks
vertical blanking interrupts. We thus have to delay disabling the whole
LVDS encoder, not just disabling the PLL, until the DU is disabled.
We could split the LVDS disable sequence by clearing the LVRES bit in
the LVDS bridge atomic disable handler, and delaying the rest of the
operations, in order to disable the LVDS output at bridge atomic disable
time, before stopping the CRTC. This would make the code more complex,
without a clear benefit, so keep the implementation simple(r).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
To prepare for a rework of the LVDS disable code, which will need to be
called from rcar_lvds_pclk_disable(), move the LVDS enable code,
currently stored in the __rcar_lvds_atomic_enable() function, to a
separate code section separate from bridge operations. It will be then
extended with the LVDS disable code.
As part of this rework the __rcar_lvds_atomic_enable() function is
renamed to rcar_lvds_enable() to more clearly indicate its purpose.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
When disabling the companion bridge in rcar_lvds_atomic_disable(),
there's no need to go through the bridge's operations to call
.atomic_disable(). Call rcar_lvds_atomic_disable() on the companion
directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
The following registers do not exist on gen4, so we should not write
them: DEF6Rm, DEF7Rm, DEF8Rm, ESCRn, OTARn.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
On H3 ES1.x two bits in DPLLCR are used to select the DU input dot clock
source. These are bits 20 and 21 for DU2, and bits 22 and 23 for DU1. On
non-ES1.x, only the higher bits are used (bits 21 and 23), and the lower
bits are reserved and should be set to 0.
The current code always sets the lower bits, even on non-ES1.x.
For both DU1 and DU2, on all SoC versions, when writing zeroes to those
bits the input clock is DCLKIN, and thus there's no difference between
ES1.x and non-ES1.x.
For DU1, writing 0b10 to the bits (or only writing the higher bit)
results in using PLL0 as the input clock, so in this case there's also
no difference between ES1.x and non-ES1.x.
However, for DU2, writing 0b10 to the bits results in using PLL0 as the
input clock on ES1.x, whereas on non-ES1.x it results in using PLL1. On
ES1.x you need to write 0b11 to select PLL1.
The current code always writes 0b11 to PLCS0 field to select PLL1 on all
SoC versions, which works but causes an illegal (in the sense of not
allowed by the documentation) write to a reserved bit field.
To remove the illegal bit write on PLSC0 we need to handle the input dot
clock selection differently for ES1.x and non-ES1.x.
Add a new quirk, RCAR_DU_QUIRK_H3_ES1_PLL, for this. This way we can
always set the bit 21 on PLSC0 when choosing the PLL as the source
clock, and additionally set the bit 20 when on ES1.x.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
rcar_du_crtc.c does a soc_device_match() in
rcar_du_crtc_set_display_timing() to find out if the SoC is H3 ES1.x, and
if so, apply a workaround.
We will need another H3 ES1.x check in the following patch, so rather than
adding more soc_device_match() calls, let's add a rcar_du_device_info
entry for the ES1, and a quirk flag,
RCAR_DU_QUIRK_H3_ES1_PCLK_STABILITY, for the workaround.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
According to hardware manual, LVDCR0 register must be cleared bit by bit
when disabling LVDS.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
[tomi.valkeinen: simplified the code a bit]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reset LVDS using the reset control as CPG reset/release is required in
the hardware manual sequence.
Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The RCAR DSI driver uses reset controller, so we should select it in the
Kconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
There's a few components in the rcar-du drm directory that don't make
sense to be selectable if DRM_RCAR_DU isn't because they are part of the
IP block so add a dependency. The drivers are still testable with
COMPILE_TEST on non-Renesas platforms as DRM_RCAR_DU itself is
selectable with COMPILE_TEST.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add DSI support for r8a779g0. The main differences to r8a779a0 are in
the PLL and PHTW setups.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for DU on r8a779g0, which is identical to DU on r8a779a0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
V3U is actually gen 4 IP, like in V4H. Bump up V3U gen in the
rcar_du_r8a779a0_info.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmO0B0QACgkQaA3BHVML
eiMKtAf9EXt5yaEonR4gsGNVD70VkebW+jPEWbEMg5hMFDHE9sjBja8T7bOxeeL1
BVofJiAuEZW9176eqeWvShuwOuiE7lf4WQLMvXfFmtHF/Nac9HUtEvOcvc1vEDUB
y6VFlVHe8mSp+Iy0WPLyZCtT4d7v2eM+VYm0HgFa74dSTzQTLGPiUI/XVb/YDaA7
FHKB5NvsMX9S1XvjxCsq0jA5bo8SSzh5CVKerdAZkBJMCSmKiY09o2p5C7vw3EAz
WUXL5CXqd9bwgvZa/9ZClQtpJaikNGoOaMSEl67rbWdVTk0LIpqx3nTY15py5LXd
SG4Wtfor3Vf1REa9TrR2uCIOmh+1gQ==
=0/PC
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2023-01-03' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.3:
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7QIwlfElAYWxRcR@linux-uq9g
Use the DEFINE_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() macros to handle
the .suspend/.resume callbacks.
These macros allow the suspend and resume functions to be automatically
dropped by the compiler when CONFIG_SUSPEND is disabled, without having
to use #ifdef guards.
This has the advantage of always compiling these functions in,
independently of any Kconfig option. Thanks to that, bugs and other
regressions are subsequently easier to catch.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221129191942.138244-4-paul@crapouillou.net
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmN6wAgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0EYH/3/RO90NbrFItraN
Lzr+d3VdbGjTu8xd1M+PRTmwh3zxLpB+Jwqr0T0A2gzL9B/D+AUPUJdrCVbv9DqS
FLJAVqoeV20dNBAHSffOOLPsgCZ+Eu+LzlNN7Iqde0e8cyZICFMNktitui84Xm/i
1NgFVgz9OZ6+aieYvUj3FrFq0p8GTIaC/oybDZrxYKcO8ZzKVMJ11swRw10wwq0g
qOOECvV3w7wlQ8upQZkzFxItKFc7EexZI6R4elXeGSJJ9Hlc092dv/zsKB9dwV+k
WcwkJrZRoezYXzgGBFxUcQtzi+ethjrPjuJuM1rYLUSIcfIW/0lkaSLgRoBu8D+I
1GfXkXs=
=gt6P
-----END PGP SIGNATURE-----
Backmerge tag 'v6.1-rc6' into drm-next
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When CONFIG_DRM=m and CONFIG_DRM_RZG2L_MIPI_DSI=y, it results in a
build failure. This patch fixes the build issue by adding dependency
to DRM.
Fixes: 7a043f978e ("drm: rcar-du: Add RZ/G2L DSI driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Enhance device lanes check by reading TXSETR register at probe(),
and enforced in rzg2l_mipi_dsi_host_attach().
As per HW manual, we can read TXSETR register only after
DPHY initialization.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
This driver supports the MIPI DSI encoder found in the RZ/G2L
SoC. It currently supports DSI video mode only.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Commit 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward
compatibility") has removed device tree overlay sources used for
backward compatibility with old bindings, but forgot to remove related
dependencies from Kconfig. Fix it.
Fixes: 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward compatibility")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
When the R-Car MIPI DSI driver was added, it was a standalone encoder
driver without any dependency to or from the R-Car DU driver. Commit
957fe62d7d ("drm: rcar-du: Fix DSI enable & disable sequence") then
added a direct call from the DU driver to the MIPI DSI driver, without
updating Kconfig to take the new dependency into account. Fix it the
same way that the LVDS encoder is handled.
Fixes: 957fe62d7d ("drm: rcar-du: Fix DSI enable & disable sequence")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move the generic fbdev implementation into its own source and header
file. Adapt drivers. No functional changes, but some of the internal
helpers have been renamed to fit into the drm_fbdev_ naming scheme.
v3:
* rename drm_fbdev.{c,h} to drm_fbdev_generic.{c,h}
* rebase onto vmwgfx changes
* rebase onto xlnx changes
* fix include statements in amdgpu
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103151446.2638-22-tzimmermann@suse.de
rcar_mipi_dsi_startup() writes correct values to VCLKSET, but as it uses
or-operation to add the new values to the current value in the register,
it should first make sure the fields are cleared.
Do this by using rcar_mipi_dsi_write() to write the VCLKSET register
with a variable that has all the unused bits zeroed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The rcar crtc depends on the clock provided from the rcar DSI bridge.
When the DSI bridge is disabled, the clock is stopped, which causes the
crtc disable to timeout.
Also, while I have no issue with the enable, the documentation suggests
to enable the DSI before the crtc so that the crtc has its clock enabled
at enable time. This is also not done by the current driver.
To fix this, we need to keep the DSI bridge enabled until the crtc has
disabled itself, and enable the DSI bridge before crtc enables itself.
Add functions rcar_mipi_dsi_pclk_enable and rcar_mipi_dsi_pclk_disable
to the rcar DSI bridge driver which the rcar driver can use to
enable/disable the DSI clock when needed. This is similar to what is
already done with the rcar LVDS bridge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Improve the DSI shutdown procedure by clearing various bits that were
set while enabling the DSI output. There has been no clear issues caused
by these, but it's safer to ensure that the features are disabled at the
start of the next DSI enable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver does not explicitly stop the video mode transmission when
disabling the output. While this doesn't seem to be causing any issues,
lets follow the steps described in the documentation and add a
rcar_mipi_dsi_stop_video() which stop the video mode transmission. This
function will also be used in later patches to stop the video
transmission even if the DSI IP is not shut down.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The DU driver uses the rcar_lvds_clk_enable() and
rcar_lvds_clk_disable() functions enable or disable the pixel clock
generated by the LVDS encoder, as it requires that clock for proper DU
operation. Rename the functions by replacing "clk" with "pclk" to make
it clearer that they related to the pixel clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Use the %p4cc format specifier to print 4CCs, which will provide a more
readable message than the raw hex value.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Commit 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward
compatibility") has removed device tree overlay sources used for
backward compatibility with old bindings, but forgot to remove related
variables from the Makefile. Fix it.
Fixes: 841281fe52 ("drm: rcar-du: Drop LVDS device tree backward compatibility")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The rcar DU driver on r8a779a0 has a bug causing some specific colors
getting converted to transparent colors, which then (usually) show as
black pixels on the screen.
The reason seems to be that the driver sets PnMR_SPIM_ALP bit in
PnMR.SPIM field, which is an illegal setting on r8a779a0. The
PnMR_SPIM_EOR bit also illegal.
Add a new feature flag for this (lack of a) feature and make sure the
bits are zero on r8a779a0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
rcar_du_regs.h is not needed by rcar_du_drv.c so drop the include.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
DRM_MODE_BLEND_PIXEL_NONE ignores an alpha channel.
Rcar-du driver supports only 3 formats with an alpha channel
(DRM_FORMAT_ARGB1555, DRM_FORMAT_ARGB8888 and DRM_FORMAT_ARGB4444). We
simply override the format passed to VSP1 for blending with the pixel
format without alpha channel.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
R-Car DU driver implicitly supports DRM_MODE_BLEND_COVERAGE only.
This adds a support for DRM_MODE_BLEND_PREMULTI. As a consequence,
DRM_MODE_BLEND_PREMULTI becomes the default. If DRM_MODE_BLEND_COVERAGE
is desired, it should be set explicitly.
This behavior comes from how DRM blend mode is supported.
drm_plane_create_blend_mode_property() creates the blend mode property
with the default value of DRM_MODE_BLEND_PREMULTI. This default value
cannot be modified from the atomic driver.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The field paddr of struct drm_gem_dma_object holds a DMA address, which
might actually be a physical address. However, depending on the platform,
it can also be a bus address or a virtual address managed by an IOMMU.
Hence, rename the field to dma_addr, which is more applicable.
In order to do this renaming the following coccinelle script was used:
```
@@
struct drm_gem_dma_object *gem;
@@
- gem->paddr
+ gem->dma_addr
@@
struct drm_gem_dma_object gem;
@@
- gem.paddr
+ gem.dma_addr
@exists@
typedef dma_addr_t;
symbol paddr;
@@
dma_addr_t paddr;
<...
- paddr
+ dma_addr
...>
@@
symbol paddr;
@@
dma_addr_t
- paddr
+ dma_addr
;
```
This patch is compile-time tested with:
```
make ARCH={x86_64,arm,arm64} allyesconfig
make ARCH={x86_64,arm,arm64} drivers/gpu/drm`
```
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-5-dakr@redhat.com
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
Rename "FB CMA" helpers to "FB DMA" helpers - considering the hierarchy
of APIs (mm/cma -> dma -> fb dma) calling them "FB DMA" seems to be
more applicable.
Besides that, commit e57924d4ae ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(FB)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(fb)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "FB CMA", but not "GEM CMA".
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-3-dakr@redhat.com
Quite a lot of drivers include the drm_fb_cma_helper.h header file
without actually making use of it's provided API, hence remove those
includes.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-2-dakr@redhat.com
Remove the include statement for drm_plane_helper.h from all the files
that don't need it. Althogh the header file is almost empty, many drivers
include it somewhere.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720083058.15371-5-tzimmermann@suse.de
