Add power domain description for sa8775p and a new compatible to match it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109174511.1740856-15-brgl@bgdev.pl
Add the power domains exposed by RPMH in the Qualcomm SM8550 platform.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116111745.2633074-3-abel.vesa@linaro.org
In some cases the hardware that the bootloader has left configured
depends on RPMH power domains for their operation up until the point
where the related Linux device driver probes and can inherit that
configuration, or power down the hardware gracefully.
Unfortunately as Linux probes the releavant drivers in sequence there
are periods during the Linux boot flow where either the genpd refcount
will reach 0, or worse where the active performance_state votes does not
meet the requirements of the state that the hardware was left in.
One specific example of this is during boot of e.g. SM8150/SC8180X,
where the display clock controller probes, without any particular
performance state needs (to access its registers). This will drop the
MMCX rail to MIN_SVS, which isn't sufficient to sustain the clock rates
that the later probing MDP is configured to. This results in an
unrecoverable system state.
Handle both these cases by keeping the RPMH power-domais that are
referenced voted for highest state, until sync_state indicates that all
devices referencing the RPMH power-domain driver has been probed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
[bjorn: Added print for sync_state errors]
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220915205559.14574-1-quic_bjorande@quicinc.com
The Snapdragon 670 has similar power domains to SDM845 but no EBI power
domain. Add a new array for them to avoid requesting a power domain which
is unsupported by the hardware.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221004221130.14076-3-mailingradian@gmail.com
The Qualcomm sc8280xp platform has 13 and the sa8540p platform has 11
power-domains. Add compatibles, the typically used ones power-domains
and their relevant active-only variants, to the RPMh power-domain
driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220426233508.1762345-4-bjorn.andersson@linaro.org
In some cases the DT binding will fully describe the set of available
RPMh power-domains, but there is no reason for exposing them all in the
implementation.
Omitting individual data->domains is handle gracefully by
of_genpd_add_provider_onecell(), so there's no reason for printing a
warning when this occurs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220426233508.1762345-3-bjorn.andersson@linaro.org
Sort all power-domain defines and the SoC specific lists in
alphabetical order for better readability.
No functional changes.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-5-git-send-email-quic_rjendra@quicinc.com
The requirement to specify the active + sleep and active-only MX
power-domains as the parents of the corresponding CX power domains is
not applicable on sc7280. Fix it by using the cx/cx_ao structs for
sc7280 instead of the _w_mx_parent ones.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-4-git-send-email-quic_rjendra@quicinc.com
The rpmhpd structs were named with a SoC-name prefix, but then
they got reused across multiple SoC families making things confusing.
Rename all the struct names to remove SoC-name prefixes.
While we do this we end up with some power-domains without parents,
and some with and at times different parents across SoCs.
use a _w_<parent-name>_parent suffix for such cases.
No functional change as part of this patch.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1639063917-9011-3-git-send-email-quic_rjendra@quicinc.com
Add the power domains exposed by RPMH in the Qualcomm SM8450 platform.
Unlike previous generations CX domain is not a child of MX domain.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201072745.3969077-7-vkoul@kernel.org
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Add the power domains exposed by RPMH in the Qualcomm SM6350 platform.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210820203105.229764-4-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
rpmhpd_aggregate_corner() takes a corner as parameter, but in
rpmhpd_power_off() the code requests the level of the first corner
instead.
In all (known) current cases the first corner has level 0, so this
change should be a nop, but in case that there's a power domain with a
non-zero lowest level this makes sure that rpmhpd_power_off() actually
requests the lowest level - which is the closest to "power off" we can
get.
While touching the code, also skip the unnecessary zero-initialization
of "ret".
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20210703005416.2668319-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds the power domains found in SDX55 SoC. Downstream code tells me
that we have 3 power domains so add them
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201126092711.1084518-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/soc/qcom/rpmhpd.c:52: warning: Function parameter or member 'parent' not described in 'rpmhpd'
drivers/soc/qcom/rpmhpd.c:52: warning: Function parameter or member 'corner' not described in 'rpmhpd'
drivers/soc/qcom/rpmhpd.c:52: warning: Function parameter or member 'active_corner' not described in 'rpmhpd'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201103152838.1290217-22-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch allow the rpmhpd driver to be loaded as a permenent
module. Meaning it can be loaded from a module, but then cannot
be unloaded.
Ideally, it would include a remove hook and related logic, but
apparently the genpd code isn't able to track usage and cleaning
things up?
So making it a permenent module at least improves things slightly
over requiring it to be a built in driver.
Cc: Todd Kjos <tkjos@google.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200326224459.105170-4-john.stultz@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The 'active_only' attribute was accidentally never set to true for any
power domains meaning that all the code handling this attribute was
dead.
NOTE that the RPM power domain code (as opposed to the RPMh one) gets
this right.
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190214173633.211000-1-dianders@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Specify the active + sleep and active-only MX power domains as
the parents of the corresponding CX power domains. This will ensure that
performance state requests on CX automatically generate equivalent requests
on MX power domains.
This is used to enforce a requirement that exists for various
hardware blocks on SDM845 that MX performance state >= CX performance
state for a given operating frequency.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The RPMh power domain driver aggregates the corner votes from various
consumers for the ARC resources and communicates it to RPMh.
With RPMh we use 2 different numbering space for corners, one used
by the clients to express their performance needs, and another used
to communicate to RPMh hardware.
The clients express their performance requirements using a sparse
numbering space which are mapped to meaningful levels like RET, SVS,
NOMINAL, TURBO etc which then get mapped to another number space
between 0 and 15 which is communicated to RPMh. The sparse number space,
also referred to as vlvl is mapped to the continuous number space of 0
to 15, also referred to as hlvl, using command DB.
Some power domain clients could request a performance state only while
the CPU is active, while some others could request for a certain
performance state all the time regardless of the state of the CPU.
We handle this by internally aggregating the votes from both type of
clients and then send the aggregated votes to RPMh.
There are also 3 different types of votes that are comunicated to RPMh
for every resource.
1. ACTIVE_ONLY:
This specifies the requirement for the resource when the CPU is
active
2. SLEEP:
This specifies the requirement for the resource when the CPU is
going to sleep
3. WAKE_ONLY:
This specifies the requirement for the resource when the CPU is
coming out of sleep to active state
We add data for all power domains on sdm845 SoC as part of the patch.
The driver can be extended to support other SoCs which support RPMh
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
