The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The value of reqsize must only be changed through the helper.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Simplify sun8i_ss_hashkey() by using crypto_shash_tfm_digest() instead
of an alloc+init+update+final sequence. This should also improve
performance.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API's support for alignmasks for ahash algorithms is nearly
useless, as its only effect is to cause the API to align the key and
result buffers. The drivers that happen to be specifying an alignmask
for ahash rarely actually need it. When they do, it's easily fixable,
especially considering that these buffers cannot be used for DMA.
In preparation for removing alignmask support from ahash, this patch
makes the sun8i-ss driver no longer use it. This driver didn't actually
rely on it; it only writes to the result buffer in sun8i_ss_hash_run(),
simply using memcpy(). And sun8i_ss_hmac_setkey() does not assume any
alignment for the key buffer.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API's support for alignmasks for ahash algorithms is nearly
useless, as its only effect is to cause the API to align the key and
result buffers. The drivers that happen to be specifying an alignmask
for ahash rarely actually need it. When they do, it's easily fixable,
especially considering that these buffers cannot be used for DMA.
In preparation for removing alignmask support from ahash, this patch
makes the sun8i-ce driver no longer use it. This driver didn't actually
rely on it; it only writes to the result buffer in sun8i_ce_hash_run(),
simply using memcpy(). And this driver only supports unkeyed hash
algorithms, so the key buffer need not be considered.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API's support for alignmasks for ahash algorithms is nearly
useless, as its only effect is to cause the API to align the key and
result buffers. The drivers that happen to be specifying an alignmask
for ahash rarely actually need it. When they do, it's easily fixable,
especially considering that these buffers cannot be used for DMA.
In preparation for removing alignmask support from ahash, this patch
makes the sun4i-ss driver no longer use it. This driver didn't actually
rely on it; it only writes to the result buffer in sun4i_hash(), already
using the unaligned access helpers. And this driver only supports
unkeyed hash algorithms, so the key buffer need not be considered.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The callbacks for prepare and unprepare request in crypto_engine
is superfluous. They can be done directly from do_one_request.
Move the code into do_one_request and remove the unused callbacks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The callbacks for prepare and unprepare request in crypto_engine
is superfluous. They can be done directly from do_one_request.
Move the code into do_one_request and remove the unused callbacks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Arm documentation has moved to Documentation/arch/arm; update a
set of references under crypto/allwinner to match.
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
SS_ENCRYPTION is (0 << 7 = 0), so the test can never be true.
Use a direct comparison to SS_ENCRYPTION instead.
The same king of test is already done the same way in sun8i_ss_run_task().
Fixes: 359e893e8a ("crypto: sun8i-ss - rework handling of IV")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At least the D1 variant requires a separate clock for the TRNG.
Without this clock enabled, reading from /dev/hwrng reports:
sun8i-ce 3040000.crypto: DMA timeout for TRNG (tm=96) on flow 3
Experimentation shows that the necessary clock is the SoC's internal
RC oscillator. This makes sense, as noise from the oscillator can be
used as a source of entropy.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
GFP_DMA does not guarantee that the returned memory is aligned
for DMA. In fact for sun8i-ss it is superfluous and can be removed.
However, kmalloc may start returning DMA-unaligned memory in future
so fix this by adding the alignment by hand.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most hw_random devices return entropy which is assumed to be of full
quality, but driver authors don't bother setting the quality knob. Some
hw_random devices return less than full quality entropy, and then driver
authors set the quality knob. Therefore, the entropy crediting should be
opt-out rather than opt-in per-driver, to reflect the actual reality on
the ground.
For example, the two Raspberry Pi RNG drivers produce full entropy
randomness, and both EDK2 and U-Boot's drivers for these treat them as
such. The result is that EFI then uses these numbers and passes the to
Linux, and Linux credits them as boot, thereby initializing the RNG.
Yet, in Linux, the quality knob was never set to anything, and so on the
chance that Linux is booted without EFI, nothing is ever credited.
That's annoying.
The same pattern appears to repeat itself throughout various drivers. In
fact, very very few drivers have bothered setting quality=1024.
Looking at the git history of existing drivers and corresponding mailing
list discussion, this conclusion tracks. There's been a decent amount of
discussion about drivers that set quality < 1024 -- somebody read and
interepreted a datasheet, or made some back of the envelope calculation
somehow. But there's been very little, if any, discussion about most
drivers where the quality is just set to 1024 or unset (or set to 1000
when the authors misunderstood the API and assumed it was base-10 rather
than base-2); in both cases the intent was fairly clear of, "this is a
hardware random device; it's fine."
So let's invert this logic. A hw_random struct's quality knob now
controls the maximum quality a driver can produce, or 0 to specify 1024.
Then, the module-wide switch called "default_quality" is changed to
represent the maximum quality of any driver. By default it's 1024, and
the quality of any particular driver is then given by:
min(default_quality, rng->quality ?: 1024);
This way, the user can still turn this off for weird reasons (and we can
replace whatever driver-specific disabling hacks existed in the past),
yet we get proper crediting for relevant RNGs.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DMA address need to be stored in a dma_addr_t
Fixes: 359e893e8a ("crypto: sun8i-ss - rework handling of IV")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use DEFINE_SHOW_ATTRIBUTE helper macro to simplify the code.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 2b02187bdb.
The original code was correct and arguably more robust than the
patched version.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using pm_runtime_resume_and_get() to instade of pm_runtime_get_sync
and pm_runtime_put_noidle.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no i decrement in while (i >= 0) loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 359e893e8a ("crypto: sun8i-ss - rework handling of IV")
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto_alloc_shash() function never returns NULL. It returns error
pointers.
Fixes: 801b7d572c ("crypto: sun8i-ss - add hmac(sha1)")
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If there is a dma_mapping_error() then return negative error codes.
Currently this code returns success.
Fixes: 801b7d572c ("crypto: sun8i-ss - add hmac(sha1)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These failure paths should return -ENOMEM. Currently they return
success.
Fixes: 359e893e8a ("crypto: sun8i-ss - rework handling of IV")
Fixes: 8eec4563f1 ("crypto: sun8i-ss - do not allocate memory when handling hash requests")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sg length could be more than remaining data on it.
So check the length requirement against the minimum between those two
values.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "Fallback for xxx" message is annoying, remove it and store the
information in the debugfs.
Let's add more precise fallback stats and display it better.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When testing with some large SG list, the sun8i-ce drivers always
fallback even if it can handle it.
So use sg_nents_for_len() which permits to see less SGs than needed.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move all padding work to a dedicated function.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sg length could be more than remaining data on it.
So check the length requirement against the minimum between those two
values.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Even if sun8i-ss does not handle hmac(sha1) directly, we can provide one
which use the already supported acceleration of sha1.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move all padding work to a dedicated function.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "Fallback for xxx" message is annoying, remove it and store the
information in the debugfs.
In the same time, reports more fallback statistics.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current sun8i-ss handle only requests with all SG length being
modulo 64.
But the last SG could be always handled by copying it on the pad buffer.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of memset all pad buffer, it is faster to only put 0 where
needed.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of allocate memory on each requests, it is easier to
pre-allocate buffers.
This made error path easier.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When testing with some large SG list, the sun8i-ss drivers always
fallback even if it can handle it.
So use sg_nents_for_len() which permits to see less SGs than needed.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The first thing we should do after dma_map_single() is to test the
result.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some fallback tests were redundant with what sun8i_ss_hash_need_fallback() already do.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sun8i-ss does not handle well the possible zero sized sg.
Fixes: d9b45418a9 ("crypto: sun8i-ss - support hash algorithms")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sun8i-ss fail handling IVs when doing decryption of multiple SGs in-place.
It should backup the last block of each SG source for using it later as
IVs.
In the same time remove allocation on requests path for storing all
IVs.
Fixes: f08fcced6d ("crypto: allwinner - Add sun8i-ss cryptographic offloader")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of allocate memory on each requests, it is easier to
pre-allocate buffer for backup IV.
This made error path easier.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of allocate memory on each requests, it is easier to
pre-allocate buffer for IV.
This made error path easier.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
