When MFP is disabled, action frames will not
be encrypted since they are management frames
and the only management frames that can then
be encrypted are authentication frames.
Therefore, setting the don't-encrypt flag on
action frames is unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WEP is unavailable, don't advertise it
to cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The decryption code verifies whether or not
a given frame was decrypted and verified by
hardware. This is unnecessary, as the crypto
RX handler already does it long before the
decryption code is even invoked, so remove
that code to avoid confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to keep separate if statements
for setting up the CCMP/AES-CMAC tfm structs;
move that into the existing switch statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we don't just need to know whether or
not the device is idle, but also per interface.
This adds that reporting capability to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new timer, which will release
queued-up MPDUs from the reorder buffer, whenever
they've waited for more than HT_RX_REORDER_BUF_TIMEOUT
(which is at around 100 ms).
The advantage of having a dedicated timer, instead of
relying on a constant stream of freshly arriving aMPDUs
to release the old ones, is particularly observable when
even a small fraction of MPDUs are forever lost at
low network speeds.
Previously under these circumstances frames would become
stuck in the reorder buffer and the network stack of both
HT peers throttled back, instead of revving up and
gunning the pipes.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a few stale parameters and variables
which survived the last, large rx-path reorganization:
"mac80211: correctly place aMPDU RX reorder code"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes the reorder logic from the RX path and
moves it into separate routines to make the expired frame
release accessible.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_add_key() currently returns -ENOMEM in case of any error,
including a missing crypto algorithm. Change ieee80211_key_alloc()
and ieee80211_aes_{key_setup_encrypt,cmac_key_setup}() to encode
errors with ERR_PTR() rather than returning NULL, and change
ieee80211_add_key() accordingly.
Compile-tested only.
Reported-by: Marcin Owsiany <porridge@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having both scan and work mutexes is not just
a bit too fine grained, it also creates issues
when there's code that needs both since they
then need to be acquired in the right order,
which can be hard to do.
Therefore, use just a single mutex for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frames that failed PLCP error checks are most likely
microwave transmissions (well, maybe not ...) and
don't have a proper rate detected, so ignore it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running in client mode and associating to an AP, the channel
change is usually performed with the offchannel flag still set.
However after the assoc is complete, the following channel change event
is suppressed because the run time channel is already set to the operating channel.
Fix this by sending channel change notifications to the driver even if
only the offchannel flag changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:
successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The warning is:
net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Releasing the scan mutex while starting scans
can lead to unexpected things happening, so
we shouldn't do that. Fix that and hold the
mutex across the scan triggering.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some features require knowing the DTIM period
before associating. This implements the ability
to wait for a beacon in mac80211 before assoc
to provide this value. It is optional since
most likely not all drivers will need this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some drivers it can be useful to know whether the channel they're
supposed to switch to is going to be used for short off-channel work or
scanning, or whether the hardware is expected to stay on it for a while
longer. This is important for various kinds of calibration work, which
takes longer to complete and should keep some persistent state, even if
the channel temporarily changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts this commit. While in theory the change is
correct the patch does not address current assumptions made
by some drivers, one which is definitley affected is ath9k.
Prior to this change the scan complete callback would be
called after we returned to the home channel and configured
the hardware RX filters. After this change we call the scan
complete callback prior to both the hw config and the config
filter. At least for ath9k this breaks quite a few assumptions
on the callback, leading to disconnects to the AP after every scan
making the driver pretty useless on STA mode. The goal behind
this commit was to address the now understood spurious warnings
from ath9k and mac80211_hwsim on scanning on two wiphys at the
same time but we have now supressed these and will address this
issue in the next kernel release.
When fixing this for good next we must first review the other
driver's dependence on this logic and perhaps consider removal
of the scan complete callback all together.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function ieee80211_subif_start_xmit the logic related with
meshdrlen is under CONFIG_MAC80211_MESH macro, but in one place it isn't.
This is some update for this
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Key locking simplification removed key->sdata != NULL verification from
ieee80211_key_free(). While that is fine for most use cases, there is one
path where this function can be called with an unlinked key (i.e.,
key->sdata == NULL && key->local == NULL). This results in a NULL pointer
dereference with the current implementation. This is known to happen at
least with FT protocol when wpa_supplicant tries to configure the key
before association.
Avoid the issue by passing in the local pointer to
ieee80211_key_free(). In addition, do not clear the key from hw_accel
or debugfs if it has not yet been added. At least the hw_accel one could
trigger another NULL pointer dereference.
Signed-off-by: Jouni Malinen <j@w1.fi>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, there is no need to notify the driver about QoS
changes for the monitor interface that is created. The warning
in ieee80211_bss_info_change_notify() would be hit otherwise.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I just had the following:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-tx.c:574 iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]()
Call Trace:
<IRQ> [<ffffffff8105c5df>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8105c63a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0290b46>] iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]
[<ffffffffa027076c>] iwl_mac_tx+0x5c/0x260 [iwlagn]
[<ffffffffa01bdf5b>] __ieee80211_tx+0x10b/0x1a0 [mac80211]
[<ffffffffa01bfb86>] ieee80211_tx_pending+0x186/0x2d0 [mac80211]
[<ffffffff81062ea5>] tasklet_action+0x125/0x130
[<ffffffff810634a6>] __do_softirq+0x106/0x270
[<ffffffff8100c09c>] call_softirq+0x1c/0x30
iwlagn 0000:02:00.0: Attempting to modify non-existing station 107
Note that 107 == 0x6b which is slab poison.
The reason is that mac80211 passed a freed station
pointer to mac80211, because as it happened iwlwifi
reset itself while mac80211 was disconnecting from
the network.
It turns out that we do take care to look up the
station pointer in ieee80211_tx_pending_skb, but
then don't use it, which obviously is a bug. Fix
this by removing the ieee80211_tx_h_sta handler
and assigning the station pointer directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another remnant of the previous key locking scheme
needs to be removed -- this causes a warning
otherwise as ieee80211_set_default_mgmt_key will
acquire a mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent was to free "msp->ratelist" here. "msp->sample_table" is
always NULL at this point.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"It's not problematic if minstrel gets feedback for rates that it
doesn't have in its list, it should just ignore it. - Felix"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>
If sta is NULL, we will have problems long before we get here...
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>
IBSS has never had locking, instead relying on some
memory barriers etc. That's hard to get right, and
I think we had it wrong too until the previous patch.
Since this is not performance sensitive, it doesn't
make sense to have the maintenance overhead of that,
so add proper locking.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob reported a lockdep complaint originating in
the mac80211 IBSS code due to the common work
struct patch. The reason is that the IBSS and
station mode code have different locking orders
for the cfg80211 wdev lock and the work struct
(where "locking" implies running/canceling).
Fix this by simply not canceling the work in
the IBSS code, it is not necessary since when
the REQ_RUN bit is cleared, the work will run
without effect if it runs. When the interface
is set down, it is flushed anyway, so there's
no concern about it running after memory has
been invalidated either.
This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=16419
Additionally, looking into this I noticed that
there's a small window while the IBSS is torn
down in which the work may be rescheduled and
the REQ_RUN bit be set again after leave() has
cleared it when a scan finishes at exactly the
same time. Avoid that by setting the ssid_len
to zero before clearing REQ_RUN which signals
to the scan finish code that this interface is
not active.
Reported-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WEP is not available, we should reject shared
key authentication because it could never succeed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station interface is reused as monitor interface it is possible that
the carrier is still set to off. This breaks packet injection on that
monitor interface.
Force the carrier on in monitor interface initialisation like it is also done
for other interface types (e.g. adhoc, mesh point, ap).
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation related action frames are enqueued for further work,
and they originate from a STA that is part of an AP VLAN, they are
currently enqueued for the AP interface. This breaks the sta_info_get()
lookup in the actual work function, and because of that, aggregation
sessions are not established for this STA.
Fix this by replacing the sta_info_get call with a call to
sta_info_get_bss.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do this by poisoning the values of wep_tx_tfm and wep_rx_tfm if either
crypto allocation fails.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will also fix the odd freeze which occurred
when minstrel_ht connects to an 802.11n network with
legacy hardware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mac80211 code assumes that WEP is always available. If WEP
fails to initialize, ieee80211_register_hw will always fail.
In some cases (e.g. FIPS certification), the cryptography used by WEP is
unavailable. However, in such cases there is no good reason why CCMP
encryption (or even no link level encryption) cannot be used. So, this
patch removes mac80211's assumption that WEP (and TKIP) will always be
available for use.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check should be against current top2 rate, instead of
current top rate.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The throughput should be considered when updating rate
with best probability.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow selection of minstrel_ht as default rate control algorithm. At
the moment minstrel_ht can only be requested by the driver code but
not selected as default in make menuconfig. Fix this by using
minstrel_ht when minstrel was selected as default and minstrel_ht
is available.
This change won't affect legacy devices as minstrel_ht falls back to
minstrel in that case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This check is duplicated in drv_get_survey.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of an ambiguity in the for_each_sta_info macro, it can
currently only be used if the third parameter is set to 'sta'.
Fix this by renaming the parameter to '_sta'.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.
Also, already in advance move the tx_power_setting enumeration to nl80211.
This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While mesh_rx_plink_frame holds sta->lock...
mesh_rx_plink_frame ->
mesh_plink_inc_estab_count ->
ieee80211_bss_info_change_notify
...but ieee80211_bss_info_change_notify is allowed to sleep. A driver
taking advantage of that allowance can cause a scheduling while
atomic bug. Similar paths exist for mesh_plink_dec_estab_count,
so work around those as well.
http://bugzilla.kernel.org/show_bug.cgi?id=16099
Also, correct a minor kerneldoc comment error (mismatched function names).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
net/mac80211/rc80211_minstrel_ht.c:440:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:440:46: expected int *idx
net/mac80211/rc80211_minstrel_ht.c:440:46: got unsigned int *<noident>
net/mac80211/rc80211_minstrel_ht.c:446:46: warning: incorrect type in argument 2 (different signedness)
net/mac80211/rc80211_minstrel_ht.c:446:46: expected int *idx
net/mac80211/rc80211_minstrel_ht.c:446:46: got unsigned int *<noident>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
net/mac80211/rx.c:2059:39: warning: symbol 'mgmt' shadows an earlier one
net/mac80211/rx.c:1916:31: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.
In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.
Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.
The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.
This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.
In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following compile warning:
CC [M] net/mac80211/scan.o
net/mac80211/scan.c: In function 'ieee80211_request_internal_scan':
net/mac80211/scan.c:749:23: warning: comparison between 'enum nl80211_band' and 'enum ieee80211_band'
caused by the local variable band not being of the proper 'ieee80211_band' type.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, detection in hwsim and ath9k can
detect that two sw scans are in flight at the
same time, which isn't really true. It is
caused by a race condition, because the scan
complete callback is called too late, after
the lock has been dropped, so that a new scan
can be started before it is called.
It is also called too early semantically, as
it is currently called _after_ the return to
the operating channel -- it should be before
so that drivers know this is the operating
channel again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regression introduced by b8d92c9c14
In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function
this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, we must use a
separate counter for tracking received CCMP packet number for the
management frames. The previously used NUM_RX_DATA_QUEUESth queue was
shared with data frames when QoS was not used and that can cause
problems in detecting replays incorrectly for robust management frames.
Add a new counter just for robust management frames to avoid this issue.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used,
Deauthentication frame needs to be protected when the pairwise key is
configured. mac80211 was removing the station entry (and its keys)
before actually sending out the Deauthentication frame. Fix this by
reordering the code to send the frame before the station entry gets
removed. This matches an earlier change that handled the Disassociation
frame processing, but missed Deauthentication frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ps-qos latency handling is broken. It uses predetermined latency values
to select specific dynamic PS timeouts. With common AP configurations, these
values overlap with beacon interval and are therefore essentially useless
(for network latencies less than the beacon interval, PSM is disabled.)
This patch remedies the problem by replacing the predetermined network latency
values with one high value (1900ms) which is used to go trigger full psm. For
backwards compatibility, the value 2000ms is still mapped to a dynamic ps
timeout of 100ms.
Currently also the mac80211 internal value for storing user space configured
dynamic PSM values is incorrectly in the driver visible ieee80211_conf struct.
Move it to the ieee80211_local struct.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a circular locking dependency when configuring the
hardware ARP filters on association, occurring when flushing the mac80211
workqueue. This is what happens:
[ 92.026800] =======================================================
[ 92.030507] [ INFO: possible circular locking dependency detected ]
[ 92.030507] 2.6.34-04781-g2b2c009 #85
[ 92.030507] -------------------------------------------------------
[ 92.030507] modprobe/5225 is trying to acquire lock:
[ 92.030507] ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8105b5c0>] flush_workq
ueue+0x0/0xb0
[ 92.030507]
[ 92.030507] but task is already holding lock:
[ 92.030507] (rtnl_mutex){+.+.+.}, at: [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507]
[ 92.030507] which lock already depends on the new lock.
[ 92.030507]
[ 92.030507]
[ 92.030507] the existing dependency chain (in reverse order) is:
[ 92.030507]
[ 92.030507] -> #2 (rtnl_mutex){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff81341754>] mutex_lock_nested+0x44/0x300
[ 92.030507] [<ffffffff812b9ce2>] rtnl_lock+0x12/0x20
[ 92.030507] [<ffffffffa022d47c>] ieee80211_assoc_done+0x6c/0xe0 [mac80211]
[ 92.030507] [<ffffffffa022f2ad>] ieee80211_work_work+0x31d/0x1280 [mac80211]
[ 92.030507] -> #1 ((&local->work_work)){+.+.+.}:
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105a51a>] worker_thread+0x22a/0x370
[ 92.030507] [<ffffffff8105ecc6>] kthread+0x96/0xb0
[ 92.030507] [<ffffffff81003a94>] kernel_thread_helper+0x4/0x10
[ 92.030507]
[ 92.030507] -> #0 ((wiphy_name(local->hw.wiphy))){+.+.+.}:
[ 92.030507] [<ffffffff81075fdc>] __lock_acquire+0x1c0c/0x1d50
[ 92.030507] [<ffffffff810761fb>] lock_acquire+0xdb/0x110
[ 92.030507] [<ffffffff8105b60e>] flush_workqueue+0x4e/0xb0
[ 92.030507] [<ffffffffa023ff7b>] ieee80211_stop_device+0x2b/0xb0 [mac80211]
[ 92.030507] [<ffffffffa0231635>] ieee80211_stop+0x3e5/0x680 [mac80211]
The locking in this case is quite complex. Fix the problem by rewriting the
way the hardware ARP filter list is handled - i.e. make a copy of the address
list to the bss_conf struct, and provide that list to the hardware driver
when needed.
The current patch will enable filtering also in promiscuous mode. This may need
to be changed in the future.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove BSS from cfg80211 BSS list if we are only member in IBSS when
leaving it.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add changed basic rates flag to bss_changed while joinig ibss network.
This patch is split from the patch containing support for setting basic
rates when creating ibss network. Original patch was posted by Johannes
Berg on the linux-wireless posting list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to nl80211 and mac80211 to set basic rates when
joining/creating ibss network.
Original patch was posted by Johannes Berg on the linux-wireless posting list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, driver tracing is sometimes invoked
after and sometimes before the actual driver
callback. This is fine as long as the driver
has no tracing itself, but as soon as it does
it gets confusing.
To make traces containing such information
easier to read, introduce a return tracer in
mac80211 that essentially brackets any driver
tracing, and invoke the real trace before the
driver's callback, only showing the return
value, if any, afterwards.
Since tracing records the process, there's no
problem with overlapping calls if that should
happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent change to processing action frames from
the management frame queue had already broken action
frame accounting, and my rework didn't help either.
So add back accounting and simplify the code with a
label rather than duplicating it, and also add
accounting for management frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even before the recent changes, the documentation
for TX aggregation was somewhat out of date. Update
it and also add documentation for the RX side.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to sleep, and indicate this in
the documentation. ath9k has some locking I
don't understand, so keep it safe and disable
BHs in it, all other drivers look fine with
the context change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the TX
aggregation code to use the mutex the RX part
already uses. The spinlock is still necessary
around some code to avoid races with TX, but
now we can also synchronize_net() to avoid
getting an inconsistent sequence number.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To achieve that, simply
call the function drivers would call, and
also use RCU in the timer to get the struct
so we don't need to rely on the spinlock in
the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for allowing drivers to sleep in
ampdu_action, change the locking in the RX
aggregation code to use a mutex, so that it
would already allow drivers to sleep. But
explicitly disable BHs around the callback
for now since the TX part cannot yet sleep,
and drivers' locking might require it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that when there was _no_ traffic at
all on a given aggregation session, it would
never time out. This won't happen unless you
forced creating a session, but fix it anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we want the code to be able to sleep
in the future, it must not be called from
the timer directly. To prepare, move it out
into the aggregation work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the block-ack session works into common
code, since it will be needed for RX agg too
in the next patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver or rate control requests starting
or stopping an aggregation session, that currently
causes a direct callback into the driver, which
could potentially cause locking problems. Also,
the functions need to be callable from contexts
that cannot sleep, and thus will interfere with
making the ampdu_action callback sleeping.
To address these issues, add a new work item for
each station that will process any start or stop
requests out of line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently maintains the ampdu_lock to
avoid starting a queue due to one aggregation
session while another aggregation session needs
the queue stopped.
We can do better, however, and instead refcount
the queue stops for this particular purpose,
thus removing the need for the lock. This will
help making ampdu_action able to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The non-irqsafe aggregation start/stop done
callbacks are currently only used by ath9k_htc,
and can cause callbacks into the driver again.
This might lead to locking issues, which will
only get worse as we modify locking. To avoid
trouble, remove the non-irqsafe versions and
change ath9k_htc to use those instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each TX
aggregation session and additionally keep a
state bitmap indicating the state it is in.
By using RCU to protect the pointer, moving
the state into the structure and some locking
trickery we can avoid locking when the TX agg
session is fully operational.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each RX
aggregation session and additionally keep a
flag indicating whether or not it is valid.
By using RCU to protect the pointer and making
sure that the memory is fully set up before it
becomes visible to the RX path, we can remove
the need for the bool that indicates validity,
as well as for locking on the RX path since it
is always synchronised against itself, and we
can guarantee that all other modifications are
done when the structure is not visible to the
RX path.
The net result is that since we remove locking
requirements from the RX path, we can in the
future use any kind of lock for the setup and
teardown code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the aggregation callback processing
to the per-sdata skb queue and a work function
rather than the tasklet.
Unfortunately, this means that it extends the
pkt_type hack to that skb queue. However, it
will enable making ampdu_action API changes
gradually, my current plan is to get rid of
this again by forcing drivers to only return
from ampdu_action() when everything is done,
thus removing the callbacks completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a corner case where we receive a fragmented
frame during a blockack session, in which case we
will terminate that session. To simplify future work
in this area that will culminate in allowing the
driver callbacks for aggregation to sleep, move the
processing of this case out of the RX path into the
interface work.
This will simplify future work because the new place
for this code doesn't require that the function will
always be atomic, which the RX path needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for making the ampdu_action callback
sleep, make mac80211 always process blockack
action frames from the skb queue. This gets rid
of the current special case for managed mode
interfaces as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code is duplicated between ibss, mesh and
managed mode regarding the queueing of management
frames. Since all modes now use a common skb
queue and a common work function, we can pull
the queueing code into the rx handler directly
and remove the duplicated length checks etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the management processing functions free the
skb after they are done, so this can be done in
the new common code instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even with the previous patch, IBSS, managed
and mesh modes all attach their own work
function to the shared work struct, which
means some duplicated code. Change that to
only have a frame processing function and a
further work function for each of them and
share some common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have their
own work struct, and in the future we want
to also use it in other modes to process
frames from the now common skb queue.
This also makes the skb queue and work safe
to use from other interface types.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS, managed and mesh modes all have an
skb queue, and in the future we want to
also use it in other modes, so make them
all use a common skb queue already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places use RCU locking for accessing
the station list, even though they do not need
to. Use mutex locking instead to prepare for the
locking changes I want to make. The mlme code is
also using a WLAN_STA_DISASSOC flag that has the
same meaning as WLAN_STA_BLOCK_BA, so use that.
While doing so, combine places where we loop
over stations twice, and optimise away some of
the loops by checking if the hardware supports
aggregation at all first.
Also fix a more theoretical race condition: right
now we could resume, set up an aggregation session,
and right after tear it down again due to the code
that is needed for hardware reconfiguration here.
Also mark add a comment to that code marking it as
a workaround.
Finally, remove a pointless aggregation disabling
loop when an interface is stopped, directly after
that we remove all stations from it which will also
disable all aggregation sessions that may still be
active, and does so in a race-free way unlike the
current loop that doesn't block new sessions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When in IBSS mode, currently action frame TX and RX
cannot be used. Allow using it to talk to any peer,
or for public action frames. Also, while at it,
restructure the code in mac80211 to make it easier
to add this for other interface types in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a window for ieee80211_ifa_changed() to get called whilst the
managed mode mutex has not been initialized when opening and stopping the
interface. Currently this causes a kernel BUG like the following:
[ 132.460013] kernel BUG at /home/wifi/iwlwifi-2.6/net/mac80211/main.c:380!
[ 132.460013] invalid opcode: 0000 [#1] SMP
The mutex is initialized during open(), hence once netif_running() is true,
the mutex should be valid. Fix by adding a netif_running() check to the
function.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: make ARP filtering depend on CONFIG_INET" introduced this
potential locking leak.
Reported-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes "iw wlan0 dump survey" work again with
mac80211-based drivers that support it, e.g. ath5k.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing an association response could take a bit
of time while we set up the hardware etc. During that
time, the AP might already send a blockack request.
If this happens very quickly on a fairly slow machine,
we can end up processing the blockack request before
the association processing has finished. Since the
blockack processing cannot sleep right now, we also
cannot make it wait in the driver.
As a result, sometimes on slow machines the iwlagn
driver gets totally confused, and no traffic can pass
when the aggregation setup was done before the assoc
setup completed.
I'm working on a proper fix for this, which involves
queuing all blockack category action frames from a
work struct, and also allowing the ampdu_action driver
callback to sleep, which will generally clean up the
code and make things easier.
However, this is a very involved and complex change.
To fix the problem at hand in a way that can also be
backported to stable, I've come up with this patch.
Here, I simply process all aggregation action frames
from the managed interface skb queue, which means
their processing will be serialized with processing
the association response, thereby fixing the problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
STA_NOTIFY_ADD and STA_NOTIFY_REMOVE have no users anymore,
and station addition/removal are indicated to drivers
using sta_add() and sta_remove(), which can sleep.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reduces the binary size by around 25k (measured on MIPS,
with CONFIG_MAC80211_DEBUG_COUNTERS enabled).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I recently made station management able
to sleep, I can now rework key management as
well; since it will no longer need a spinlock
and can also use a mutex instead, a bunch of
code to allow drivers' set_key to sleep while
key management is protected by a spinlock can
now be removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some odd reason, the plink_state enum is
declared in the middle between aggregation
related structures. Move it down to make the
file easier to read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After ieee80211_rx_h_ctrl() processing we only
want to process management (including action)
frames, so there's no point in letting control
frames continue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since we use only cfg80211 for configuration,
there is no configuration that could be pending at
this point, cfg80211 will have the configuration
that is pending and apply it afterwards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I suspect the compiler will do this optimisation
anyway, but it seems cleaner to move this into
the WEP switch case.
Also make rx_h_decrypt use a local variable for
the frame_control so that we don't need to reload
the hdr variable for this after linearizing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.
The debugfs code I recently added got this wrong
as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware allow extended filtering of ARP frames not intended for
the host. To perform such filtering, the hardware needs to know the current
IP address(es) of the host, bound to its interface.
Add support for ARP filtering to mac80211 by adding a new op to the driver
interface, allowing to configure the current IP addresses. This op is called
upon association with the currently configured address(es), and when
associated whenever the IP address(es) change.
This patch adds configuration of IPv4 addresses only, as IPv6 addresses don't
need ARP filtering.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code has a bogus mod_timer(..., 0) call,
we shouldn't ever pass a constant value to the
function since any constant value could be in the
future or the past.
However, invoking the timer here is not necessary
at all, since we just finished scanning and just
need to have the IBSS code run again from the
workqueue later, so factor out the work starting
and use that instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup patch.
Use new __packed annotation in net/ and include/
(except netfilter)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending action frames, we want to verify
that we do that on the correct channel. However,
checking the channel type in addition can get in
the way, since the channel type could change on
the fly during an association, and it's not
useful to have the channel type anyway since it
has no effect on the transmission. Therefore,
make it optional to specify so that if wanted,
it can still be checked, but is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dialog token allocator has apparently been broken
since b83f4e15 ("mac80211: fix deadlock in sta->lock")
because it got moved out under the spinlock. Fix it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel reported that the paged RX changes had
broken blockack request frame processing due
to using data that wasn't really part of the
skb data.
Fix this using skb_copy_bits() for the needed
data. As a side effect, this adds a check on
processing too short frames, which previously
this code could do.
Reported-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse correctly complains that
__ieee80211_get_channel_mode is not static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
drivers/net/usb/asix.c: Fix pointer cast.
be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
proc_dointvec: write a single value
hso: add support for new products
Phonet: fix potential use-after-free in pep_sock_close()
ath9k: remove VEOL support for ad-hoc
ath9k: change beacon allocation to prefer the first beacon slot
sock.h: fix kernel-doc warning
cls_cgroup: Fix build error when built-in
macvlan: do proper cleanup in macvlan_common_newlink() V2
be2net: Bug fix in init code in probe
net/dccp: expansion of error code size
ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
wireless: fix sta_info.h kernel-doc warnings
wireless: fix mac80211.h kernel-doc warnings
iwlwifi: testing the wrong variable in iwl_add_bssid_station()
ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
ath9k_htc: dereferencing before check in hif_usb_tx_cb()
rt2x00: Fix rt2800usb TX descriptor writing.
rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
...
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix sta_info.h kernel-doc warnings:
Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97, since it
breaks resume from suspend-to-ram on Rafael's Acer Ferrari One.
NetworkManager thinks everything is ok, but it can't connect to the AP
to get an IP address after the resume.
In fact, it even breaks resume for non-ath9k chipsets: reverting it also
fixes Rafael's Toshiba Protege R500 with the iwlagn driver. As Johannes
says:
"Indeed, this patch needs to be reverted. That mac80211 change is wrong
and completely unnecessary."
Reported-and-requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Yingqiang Ma <yma.cool@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paged RX skb patch broke the defragmentation. We need to read hdr again
after linearization.
It fixes following bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2194
Signed-off-by: Zhu, Yi <yi.zhu@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the mode in channel switch ie for either 0 or 1 on transmission.
A channel switch mode set to 1 means that the STA in a BSS to which the
frame containing the element is addressed shall transmit no further
frames within the BSS until the scheduled channel switch.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.
In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we process a frame, we currently just match it
to the work struct by the MAC addresses, and not by
the work type. This means that we can end up doing
the work for an association request item when (for
whatever reason) we receive another frame type, for
example a probe response. Processing the wrong type
of frame will lead to completely invalid data being
processed, and will lead to various problems like
thinking the association was successful even if the
AP never sent an assocation response.
Fix this by making each processing function check
that it is invoked for the right work struct type
only and continue processing otherwise (and drop
frames that we didn't expect).
This bug was uncovered during the debugging for
https://bugzilla.kernel.org/show_bug.cgi?id=15862
but doesn't seem to be the cause for any of the
various problems reported there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Also simplify the flags assignment into a single statement at the
end of ieee80211_beacon_get_tim.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when one interface switches HT mode,
all others will follow along. This is clearly
undesirable, since the new one might switch to
no-HT while another one is operating in HT.
Address this issue by keeping track of the HT
mode per interface, and allowing only changes
that are compatible, i.e. switching into HT40+
is not possible when another interface is in
HT40-, in that case the second one needs to
fall back to HT20.
Also, to allow drivers to know what's going on,
store the per-interface HT mode (channel type)
in the virtual interface's bss_conf.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.
Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=15794 a user encountered the
following:
[18967.469098] wlan0: authenticated
[18967.472527] wlan0: associate with 00:1c:10:b8:e3:ea (try 1)
[18967.472585] wlan0: deauthenticating from 00:1c:10:b8:e3:ea by local choice (reason=3)
[18967.672057] wlan0: associate with 00:1c:10:b8:e3:ea (try 2)
[18967.872357] wlan0: associate with 00:1c:10:b8:e3:ea (try 3)
[18968.072960] wlan0: association with 00:1c:10:b8:e3:ea timed out
[18968.076890] ------------[ cut here ]------------
[18968.076898] WARNING: at net/wireless/mlme.c:341 cfg80211_send_assoc_timeout+0xa8/0x140()
[18968.076900] Hardware name: GX628
[18968.076924] Pid: 1408, comm: phy0 Not tainted 2.6.34-rc4-00082-g250541f-dirty #3
[18968.076926] Call Trace:
[18968.076931] [<ffffffff8103459e>] ? warn_slowpath_common+0x6e/0xb0
[18968.076934] [<ffffffff8157c2d8>] ? cfg80211_send_assoc_timeout+0xa8/0x140
[18968.076937] [<ffffffff8103ff8b>] ? mod_timer+0x10b/0x180
[18968.076940] [<ffffffff8158f0fc>] ? ieee80211_assoc_done+0xbc/0xc0
[18968.076943] [<ffffffff81590d53>] ? ieee80211_work_work+0x553/0x11c0
[18968.076945] [<ffffffff8102d931>] ? finish_task_switch+0x41/0xb0
[18968.076948] [<ffffffff81590800>] ? ieee80211_work_work+0x0/0x11c0
[18968.076951] [<ffffffff810476fb>] ? worker_thread+0x13b/0x210
[18968.076954] [<ffffffff8104b6b0>] ? autoremove_wake_function+0x0/0x30
[18968.076956] [<ffffffff810475c0>] ? worker_thread+0x0/0x210
[18968.076959] [<ffffffff8104b21e>] ? kthread+0x8e/0xa0
[18968.076962] [<ffffffff810031f4>] ? kernel_thread_helper+0x4/0x10
[18968.076964] [<ffffffff8104b190>] ? kthread+0x0/0xa0
[18968.076966] [<ffffffff810031f0>] ? kernel_thread_helper+0x0/0x10
[18968.076968] ---[ end trace 8aa6265f4b1adfe0 ]---
As explained by Johannes Berg <johannes@sipsolutions.net>:
We authenticate successfully, and then userspace requests association.
Then we start that process, but the AP doesn't respond. While we're
still waiting for an AP response, userspace asks for a deauth. We do
the deauth, but don't abort the association work. Then once the
association work times out we tell cfg80211, but it no longer wants
to know since for all it is concerned we accepted the deauth that
also kills the association attempt.
Fix this by, upon receipt of deauth request, removing the association work
and continuing to send the deauth.
Unfortunately the user reporting the issue is not able to reproduce this
problem anymore and cannot verify this fix. This seems like a well understood
issue though and I thus present the patch.
Bug-identified-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: improve IBSS scanning" was missing a hunk.
This adds that hunk as originally intended.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IBSS is fixed to a frequency, it can still
scan to try to find the right BSSID. This makes
sense if the BSSID isn't also fixed, but it need
not scan all channels -- just one is sufficient.
Make it do that by moving the scan setup code to
ieee80211_request_internal_scan() and include
a channel variable setting.
Note that this can be further improved to start
the IBSS right away if both frequency and BSSID
are fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows enabling TX and disabling both TX and
RX aggregation sessions manually in debugfs. It is
very useful for debugging session initiation and
teardown problems since with this you don't have
to force a lot of traffic to get aggregation and
thus have less data to analyse.
Also, to debug mac80211 code itself, make hwsim
"support" aggregation sessions. It will still just
transfer the frame, but go through the setup and
teardown handshakes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both of these functions can currently return
a station pointer that, to the driver, is
invalid (in IBSS mode only) because adding
the station failed. Check for that, and also
make ieee80211_find_sta() properly use the
per interface station search.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch "iwlwifi: work around passive scan issue" was merged into
wireless-2.6, but touched a lot of code since modified (and moved)
in wireless-next-2.6. This caused some conflicts.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
My previous patch "mac80211: notify driver about
IBSS status" left a problem -- when we merge with
a new BSSID, we never tell the driver that we left
the old one. Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (e.g. iwlwifi) need to know and try
to figure it out based on other things, but making
it explicit is definitely better.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If AP do not provide us supported rates before assiociation, send
all rates we are supporting instead of empty information element.
v1 -> v2: Add comment.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use old supported rates, if AP do not provide supported rates
information element in a new managment frame.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
if (len > tx->local->hw.wiphy->rts_threshold) {
txrc.rts = rts = true;
}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
len = min_t(int, tx->skb->len + FCS_LEN,
tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.
CC: stable@kernel.org
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A misplaced interface type check bails out too early if the interface
is not in monitor mode. This patch moves it to the right place, so that
it only covers changes to the monitor flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta->last_tx_rate is traditionally updated just before transmitting a
frame based on information from the rate control algorithm. However, for
hardware drivers with IEEE80211_HW_HAS_RATE_CONTROL this is not performed,
as the rate control algorithm is not executed, and because the used rate is
not known before the frame has actually been transmitted.
This causes atleast a fixed 1Mb/s to be reported to user space. A few other
instances of code also rely on this information.
Fix this by setting the sta->last_tx_rate in tx_status handling. There, look
for last rates entry set by the driver, and use that as value for
sta->last_tx_rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_HW_CONNECTION_MONITOR is configured by the driver, starting
of ieee80211_sta_conn_mon_timer should be prevented, as it is then not needed.
This is currently partially the case. As it seems, when a probe-response is
received from the AP the timer is still restarted, thus restarting the host
based connection keep-alive mechanism. These probe-responses happen at least
when scanning while associated.
Fix this by preventing starting of the ieee80211_sta_conn_mon_timer in the
ieee80211_rx_mgmt_probe_resp function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.
The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.
It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.
I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.
Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One HT debugging printk is missing a newline,
add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.
Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.
Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle reported that his system deadlocks since my
recent work in this area. The reason quickly became
apparent: we try to cancel_timer_sync() a timer
from within itself. Fix that by making the function
aware of the context it is called from.
Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.
Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.
This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.
See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.
Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As scan_work is queued from work_work it needs to be checked if scan
has been started during execution of work_work. Otherwise, when hw
scan is used, the stack gets error about hw being busy with ongoing
scan. This causes the stack to abort scan without notifying the driver
about it. This leads to a situation where the hw is scanning and the stack
thinks it's not. Then when the scan finishes, the stack will complain by
warnings.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We delay the skb linearising in ieee80211_rx_h_decrypt so that
frames do not require software decryption are not linearized. We
are safe to do this because ieee80211_get_mmie_keyidx() only
requires to touch nonlinear data for management frames, which are
already linearized before getting here.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grouped mesh action codes together with the other action codes in
ieee80211.h.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WEP crypto was broken, but upon finding the problem
it is evident that other things were broken by the
paged RX patch as well.
To fix it, for now move the linearising in front.
This means that we linearise all frames, which is
not at all what we want, but at least it fixes the
problem for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few places in mac80211 do not currently acquire
the sta lock for RX aggregation, but they should.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.
As a side effect, this gets rid of the long code
block to destroy aggregation safely.
Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.
Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.
Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.
Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e34e09401ee9888dd662b2fca5d607794a56daf2 incorrectly removed
use of ieee80211_has_protected() from the management frame case and in
practice, made this validation drop all Action frames when MFP is
enabled. This should have only been done for frames with Protected
field set to zero.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new RCU lockdep support warns about these
in some contexts -- make it aware of the locks
used to protect all this. Different locks are
used in different contexts which unfortunately
means we can't get perfect checking.
Also remove rcu_dereference() from two places
that don't actually dereference the pointers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the problem introduced in commit
8404080568 which broke mesh peer link establishment.
changes:
v2 Added missing break (Johannes)
v3 Broke original patch into two (Johannes)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
Fix kernel panic by NULL pointer dereference in the context of
ieee80211_ops->prepare_multicast().
This bug was introduced by commit 22bedad3c.. ("net: convert
multicast list to list_head").
Call __hw_addr_init() in ieee80211_alloc_hw() to initialize
list_head of private device multicast list, like we do in
bond_init().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bef5d1c70d split
ieee80211_drop_unencrypted() into separate functions that are used for
Data and Management frames. However, it did not handle the
RX_FLAG_DECRYPTED correctly for Management frames:
ieee80211_drop_unencrypted() can only return 0 for Management frames,
so there is no point in calling it here. Instead, just check the
status->flag directly.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the RX key for group-addressed robust management
frames, we do not actually select any BIP key if the frame is
unprotected (since we cannot find the key index from MMIE). This
results in the drop_unencrypted check in failing to drop the frame. It
is enough to verify that we have a STA entry for the transmitter and
that MFP is enabled for that STA; we do not need to check rx->key
here. This fixes BIP processing for unprotected, group-addressed,
robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIP (part of IEEE 802.11w) is only supposed to be used with
group-addressed frames. We ended up picking it as a default mechanism
for every management whenever we did not have a STA entry for the
destination (e.g., for Probe Response to a STA that is not
associated). While the extra MMIE in the end of management frames
should not break frames completed in most cases, there is no point in
doing this. Fix key selection to pick the default management key only
if the frame is sent to multicast/broadcast address and the frame is a
robust management frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When management frame protection (IEEE 802.11w) is used, the
deauthentication and disassociation frames must be protected whenever
the encryption keys are configured. We were removing the STA entry and
with it, the keys, just before actually sending out these frames which
meant that the frames went out unprotected. The AP will drop them in
such a case. Fix this by reordering the operations a bit so that
sta_info_destroy_addr() gets called only after
ieee80211_send_deauth_disassoc().
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calculate a running average of the signal strength reported for Beacon
frames and indicate cqm events if the average value moves below or
above the configured threshold value (and filter out repetitive events
with by using the configured hysteresis).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable QoS explicitly, when user space AP program will setup a QoS
queues. Currently this is not needed as iwlwifi not work in AP mode
and no other driver implement enable/disable QoS.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers
enable it explicitly when ->conf_tx method is called, and newer disable.
Disabling is needed for some APs, which do not support QoS, such
we should send QoS frames to them.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 drivers can now pass paged SKBs to mac80211 via
ieee80211_rx{_irqsafe}. The implementation currently use
skb_linearize() in a few places i.e. management frame
handling, software decryption, defragmentation and A-MSDU
process. We will optimize them one by one later.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: Kalle Valo <kalle.valo@iki.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1st) a PREQ should only be processed, if it has the same SN and better
metric (instead of better or equal).
2nd) next_hop[ETH_ALEN] now actually used to buffer
mpath->next_hop->sta.addr for use out of lock.
Signed-off-by: Marco Porsch <marco.porsch@siemens.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
We don't need "sdata" any more after:
d84f323477
mac80211: remove dev_hold/put calls
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.
also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a cooked monitor interface is active, ieee80211_tx_status()
generates a radiotap header for every single frame, even if it wasn't
injected and thus won't be sent to a monitor interface.
This patch reduces cpu utilization by moving the cooked monitor check a
bit earlier, before it generates the rtap header.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
This patch makes it possible to reuse the minstrel rate control ops
from another rate control module. This is useful in preparing for the
new 802.11n implementation of minstrel, which will reuse the old code
for legacy stations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the debugfs read function for the statistics by
using simple_read_from_buffer instead of its own semi-broken hack.
Also removes a useless member of the minstrel debugfs info struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I discovered that if EMBEDDED=y, one can accidentally build a mac80211 stack
and drivers w/ no rate control algorithm. For drivers like RTL8187 that don't
supply their own RC algorithms, this will cause ieee80211_register_hw to
fail (making the driver unusable).
This will tell kconfig to provide a warning if no rate control algorithms
have been selected. That'll at least warn the user; users that know that
their drivers supply a rate control algorithm can safely ignore the
warning, and those who don't know (or who expect to be using multiple
drivers) can select a default RC algorithm.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix memory leak and use kmalloc() instead of kzalloc() as we are going
to overwrite the allocated buffer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently hardware with !IEEE80211_HW_PS_NULLFUNC_STACK and
IEEE80211_HW_REPORTS_TX_ACK_STATUS will never enter PSM due to the
conditions in the power save entry functions.
Fix those conditions.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 34e895075e introduced sta_mtx
locking into sta_info_insert() (now sta_info_insert_rcu), but forgot
to unlock this mutex on one of the error paths. Fix this by adding
the missing mutex_unlock() call for the case where STA insert fails
due to an entry existing already. This may happen at least in AP mode
when a STA roams between two BSSes (vifs).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can now advertise to cfg80211 that they have
multiple MAC addresses reserved for a device, but we
don't currently make use of that in mac80211.
Change that and assign different addresses to new
virtual interfaces (if addresses are available) in
order to make it easier for users to use multiple
virtual interfaces; they no longer need to always
assign a new MAC address manually.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current software scan implemenation in mac80211 returns to the operating
channel after each scanned channel. However, in some situations (e.g. no
traffic) it would be nicer to scan a few channels in a row to speed up
the scan itself.
Hence, after scanning a channel, check if we have queued up any tx frames and
return to the operating channel in that case.
Unfortunately we don't know if the AP has buffered any frames for us. Hence,
scan only as many channels in a row as the pm_qos latency and the negotiated
listen interval allows us to.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.
also the section of the ibss code which deals with updating supported rates for
an already existing station fails to inform the rate control module about the
new rates. as i don't know how to fix this (minstrel does not have an update
function), i have just added a comment for now.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise value as is won't be used, isn't
filled by most drivers and doesn't really
make a whole lot of sense on a per packet
basis -- proper cfg80211 survey support in
mac80211 will need to be different.
Mark the struct member as deprecated so it
will be removed from drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e1dd33f60ced091114e4aacf141e0d03b88d3e13 changed cfg80211 to
allow association commands while in associated state to enable support
for roaming within an ESS. However, this was not enough to resolve all
cases with mac80211 which needs some additional handling of the
reassociation case to clear internal state with the BSS that was in use
previously.
This patch makes ieee80211_mgd_assoc() accept a valid reassociation
command and clean the association state with the previous BSS. This
fixes roaming between BSSes in an ESS when using wpa_supplicant with
-Dnl80211.
Signed-off-by: Jouni Malinen <j@w1.fi>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If authentication has already been performed when the WLAN interface is
stopped, (sometimes) the ieee80211_work_purge would corrupt some
ieee80211_work-structures. The outcome is this (cleaned up):
[ 2252.398681] WARNING: at net/mac80211/work.c:995 ieee80211_work_purge
[ 2252.466430] Backtrace:
[ 2252.529266] (ieee80211_work_purge+0x0/0xcc [mac80211])
[ 2252.546875] (ieee80211_stop+0x0/0x4c0 [mac80211])
Additionally, one would get this, going on regarless of the WLAN interface
state, going on forever:
[ 2252.859985] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717525)
[ 2253.055419] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717524)
[ 2253.250610] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717523)
[ 2253.446014] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717522)
[ 2253.641357] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717521)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently if a driver does not set hw.max_listen_interval a listen
interval of 1 is negotiated with the AP. Thus, the AP could drop
buffered frames for us after just one beacon interval which can
easily happen with the current powersave and scan implementation.
To avoid this issue increase the default interval to 5 which should
be a reasonable safe default.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
