The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174651.4058753-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Symbol ARCH_BCM4908 has been merged/removed without updating leds
Kconfig.
Fixes: dd5c672d7c ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230714063214.3791-1-zajec5@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
This is used for the Siemens Simatic IPC BX-21A, which has its LEDs
connected to GPIOs provided by the Intel Elkhart Lake pinctrl driver.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20230713115639.16419-3-henning.schild@siemens.com
Signed-off-by: Lee Jones <lee@kernel.org>
The PCA995x chips are I2C controlled LED drivers. Each chip has
up to 16 outputs, each one with an individual 8-bit resolution
PWM for brightness control.
Signed-off-by: Isai Gaspar <isaiezequiel.gaspar@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Basically rewrite the driver
Link: https://lore.kernel.org/r/20230713163516.21644-2-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
Negative -EINVAL was intended, not positive EINVAL. Fix it.
Fixes: 95138e0127 ("leds: pwm: Make error handling more robust")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/a33b981a-b2c4-4dc2-b00a-626a090d2f11@moroto.mountain
Signed-off-by: Lee Jones <lee@kernel.org>
Normally, the maximum brightness is determined by the hardware, and this
property is not required. This property is used to set a software limit.
It could happen that an LED is made so bright that it gets damaged or
causes damage due to restrictions in a specific system, such as mounting
conditions.
Note that this flag is mainly used for PWM-LEDs, where it is not possible
to map brightness to current. Drivers for other controllers should use
led-max-microamp.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/r/20230703130313.548519-3-astrid.rost@axis.com
Signed-off-by: Lee Jones <lee@kernel.org>
A recent rework accidentally lost the dependency on LEDS_CLASS, which
leads to a link error when LED support is disbled:
x86_64-linux-ld: drivers/leds/simple/simatic-ipc-leds.o: in function `simatic_ipc_leds_probe':
simatic-ipc-leds.c:(.text+0x10c): undefined reference to `devm_led_classdev_register_ext'
Add back the dependency that was there originally.
Fixes: a6c80bec3c ("leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230623152233.2246285-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
- New Device Support
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
- New Functionality
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
- Fix-ups
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
- Bug Fixes
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues
-----BEGIN PGP SIGNATURE-----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=9kd5
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Intel Cherry Trail Whiskey Cove PMIC LEDs
- Add support for Awinic AW20036/AW20054/AW20072 LEDs
New Device Support:
- Add support for PMI632 LPG to QCom LPG
- Add support for PMI8998 to QCom Flash
- Add support for MT6331, WLEDs and MT6332 to Mediatek MT6323 PMIC
New Functionality:
- Implement the LP55xx Charge Pump
- Add support for suspend / resume to Intel Cherry Trail Whiskey Cove PMIC
- Add support for breathing mode to Intel Cherry Trail Whiskey Cove PMIC
- Enable per-pin resolution Pinctrl in LEDs GPIO
Fix-ups:
- Allow thread to sleep by switching from spinlock to mutex
- Add lots of Device Tree bindings / support
- Adapt relationships / dependencies driven by Kconfig
- Switch I2C drivers from .probe_new() to .probe()
- Remove superfluous / duplicate code
- Replace strlcpy() with strscpy() for efficiency and overflow prevention
- Staticify various functions
- Trivial: Fixing coding style
- Simplify / reduce code
Bug Fixes:
- Prevent NETDEV_LED_MODE_LINKUP from being cleared on rename
- Repair race between led_set_brightness(LED_{OFF,FULL})
- Fix Oops relating to sleeping in critical sections
- Clear LED_INIT_DEFAULT_TRIGGER flag when clearing the current trigger
- Do not leak resources in error handling paths
- Fix unsigned comparison which can never be negative
- Provide missing NULL terminating entries in tables
- Fix misnaming issues"
* tag 'leds-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (53 commits)
leds: leds-mt6323: Adjust return/parameter types in wled get/set callbacks
leds: sgm3140: Add richtek,rt5033-led compatible
dt-bindings: leds: sgm3140: Document richtek,rt5033 compatible
dt-bindings: backlight: kinetic,ktz8866: Add missing type for "current-num-sinks"
dt-bindings: leds: Drop unneeded quotes
leds: Fix config reference for AW200xx driver
leds: leds-mt6323: Add support for WLEDs and MT6332
leds: leds-mt6323: Add support for MT6331 leds
leds: leds-mt6323: Open code and drop MT6323_CAL_HW_DUTY macro
leds: leds-mt6323: Drop MT6323_ prefix from macros and defines
leds: leds-mt6323: Specify registers and specs in platform data
dt-bindings: leds: leds-mt6323: Document mt6332 compatible
dt-bindings: leds: leds-mt6323: Document mt6331 compatible
leds: simatic-ipc-leds-gpio: Introduce more Kconfig switches
leds: simatic-ipc-leds-gpio: Split up into multiple drivers
leds: simatic-ipc-leds-gpio: Move two extra gpio pins into another table
leds: simatic-ipc-leds-gpio: Add terminating entries to gpio tables
leds: flash: leds-qcom-flash: Fix an unsigned comparison which can never be negative
leds: cht-wcove: Remove unneeded semicolon
leds: cht-wcove: Fix an unsigned comparison which can never be negative
...
Clang's kernel Control Flow Integrity (kCFI) is a compiler-based
security mitigation that ensures the target of an indirect function call
matches the expected type of the call and trapping if they do not match
exactly. The warning -Wincompatible-function-pointer-types-strict aims
to catch these issues at compile time, which reveals:
drivers/leds/leds-mt6323.c:598:49: error: incompatible function pointer types assigning to 'int (*)(struct led_classdev *, enum led_brightness)' from 'int (struct led_classdev *, unsigned int)' [-Werror,-Wincompatible-function-pointer-types-strict]
598 | leds->led[reg]->cdev.brightness_set_blocking =
| ^
599 | mt6323_wled_set_brightness;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/leds/leds-mt6323.c:600:40: error: incompatible function pointer types assigning to 'enum led_brightness (*)(struct led_classdev *)' from 'unsigned int (struct led_classdev *)' [-Werror,-Wincompatible-function-pointer-types-strict]
600 | leds->led[reg]->cdev.brightness_get =
| ^
601 | mt6323_get_wled_brightness;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
While 'unsigned int' is ABI compatible with 'enum led_brightness' (hence
no warning from -Wincompatible-function-pointer-types) and the callers
of these callbacks use/pass the values as 'unsigned int', the mismatch
between the prototype and the called function will trip kCFI at runtime.
Change the types in the implementations to match the prototypes, clearing
up the warning and avoiding kCFI failures.
Fixes: 9bb0a9e062 ("leds: leds-mt6323: Add support for WLEDs and MT6332")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230622-mt6323-wled-wincompatible-function-pointer-types-strict-v1-1-6ad256f220e8@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Expose hw_control status via sysfs for the netdev trigger to give
userspace better understanding of the current state of the trigger and
the LED.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link duplex. Use ethtool APIs to get the
current link duplex and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link duplex.
Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add additional modes for specific link speed. Use ethtool APIs to get the
current link speed and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw
control for specific link speed. (example scenario a PHY that have 2 LED
connected one green and one orange where the green is turned on with
1000mbps speed and orange is turned on with 10mpbs speed)
On mode set from sysfs we check if we have enabled split link speed mode
and reject enabling generic link mode to prevent wrong and redundant
configuration.
Rework logic on the set baseline state to support these new modes to
select if we need to turn on or off the LED.
Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 36a87f371b ("leds: Add AW20xx driver") adds config LEDS_AW200XX
in drivers/leds/Kconfig, but then in drivers/leds/Makefile accidently
refers to CONFIG_LEDS_W200XX; note the missing A!
This typo makes it impossible to add the driver to a kernel build.
Fix this wrong config reference.
Fixes: 36a87f371b ("leds: Add AW20xx driver")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230609100233.4111-1-lukas.bulwahn@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
The qca8k_cled_hw_control_get() function which implements ->hw_control_get
sets the appropriate bits but does not clear them. This leads to an
uninitialized variable bug. Fix this by setting mode to zero at the
start.
Fixes: e0256648c8 ("net: dsa: qca8k: implement hw_control ops")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic code to turn on and off WLEDs and wire up MT6332 support
to take advantage of it.
This is a simple approach due to the aforementioned PMIC supporting
only on/off status so, at the time of writing, it is impossible for me
to validate more advanced functionality due to lack of hardware.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-9-angelogioacchino.delregno@collabora.com
Add the register offsets for MT6331. The hwspec is the same as MT6323.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-8-angelogioacchino.delregno@collabora.com
There is only one instance of using this macro and it's anyway not
simplifying the flow, or increasing the readability of this driver.
Drop this macro by open coding it in mt6323_led_set_blink().
No functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-7-angelogioacchino.delregno@collabora.com
This renames all definitions and macros to drop the MT6323_ prefix,
since it is now possible to easily add support to more PMICs in
this driver.
While at it, also fix related formatting where possible.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-6-angelogioacchino.delregno@collabora.com
In order to enhance the flexibility of this driver and let it support
more than just one MediaTek LEDs IP for more than just one PMIC,
add platform data structure specifying the register offsets and
data that commonly varies between different IPs.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230601110813.2373764-5-angelogioacchino.delregno@collabora.com
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd6 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84 ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee411 ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dab ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To describe the dependency chain better and allow for potential
fine-grained config tuning, introduce Kconfig switch for the individual
GPIO based drivers.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-5-henning.schild@siemens.com
In order to clearly describe the dependencies between the GPIO
controller drivers and the users the driver is split up into a core,
two drivers and a common header.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-4-henning.schild@siemens.com
There are two special pins needed to init the LEDs. We used to have them
at the end of the gpiod_lookup table to give to "leds-gpio". A cleaner
way is to have a dedicated table for the special pins.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-3-henning.schild@siemens.com
The entries do not seem to be stricly needed when the number of entries
is given via the number of LEDs. But adding them is a safeguard should
anyone ever iterate over the tables to their end, it also gets us in
line with other drivers that register "leds-gpio" tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230524124628.32295-2-henning.schild@siemens.com
The variable 'count' is defined as unsigned type, so the following if
statement is invalid, we can modify the type of count to int.
if (count <= 0) {
dev_err(dev, "No led-sources specified\n");
return -ENODEV;
}
./drivers/leds/flash/leds-qcom-flash.c:546:5-10: WARNING: Unsigned expression compared with zero: count <= 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5344
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531053559.5702-1-jiapeng.chong@linux.alibaba.com
The return value from the call to cht_wc_leds_find_freq() is int.
However, the return value is being assigned to an unsigned
int variable 'ctrl', so making it an int.
Eliminate the following warning:
drivers/leds/leds-cht-wcove.c:236 cht_wc_leds_set_effect() warn: unsigned 'ctrl' is never less than zero.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=5341
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230531020238.102684-1-yang.lee@linux.alibaba.com
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed376 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
This commit adds support for AWINIC AW20036/AW20054/AW20072 LED driver.
This driver supports following AW200XX features:
- Individual 64-level DIM currents
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230519130403.212479-3-mmkurbanov@sberdevices.ru
Signed-off-by: Lee Jones <lee@kernel.org>
Expose netdev trigger modes to make them accessible by LED driver that
will support netdev trigger for hw control.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On netdev trigger activation, hw control may be already active by
default. If this is the case and a device is actually provided by
hw_control_get_device(), init the already active mode and set the
bool to hw_control bool to true to reflect the already set mode in the
trigger_data.
Co-developed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdev which the LED should blink for is configurable in
/sys/class/led/foo/device_name. Ensure when offloading that the
configured netdev is the same as the netdev the LED is associated
with. If it is not, only perform software blinking.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for LED hw control for the netdev trigger.
The trigger on calling set_baseline_state to configure a new mode, will
do various check to verify if hw control can be used for the requested
mode in can_hw_control() function.
It will first check if the LED driver supports hw control for the netdev
trigger, then will use hw_control_is_supported() and finally will call
hw_control_set() to apply the requested mode.
To use such mode, interval MUST be set to the default value and net_dev
MUST be set. If one of these 2 value are not valid, hw control will
never be used and normal software fallback is used.
The default interval value is moved to a define to make sure they are
always synced.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject interval store with hw_control enabled. It's are currently not
supported and MUST be set to the default value with hw control enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic check for hw control support. Check if the required API are
defined and check if the defined trigger supported in hw control for the
LED driver match netdev.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function to check if the requested mode can use hw control in
preparation for hw control support. Currently everything is handled in
software so can_hw_control will always return false.
Add knob with the new value hw_control in trigger_data struct to
set hw control possible. Useful for future implementation to implement
in set_baseline_state() the required function to set the requested mode
using LEDs hw control ops and in other function to reject set if hw
control is currently active.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code into a helper, ready for it to be called at
other times. No intended behaviour change.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each gpio-leds DT node DT subnode can have a pinctrl property assigned
to it, parse the DT subnode pinctrl properties and configure each pin
accordingly.
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230523183151.5460-1-marex@denx.de
Signed-off-by: Lee Jones <lee@kernel.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/20230522105049.1467313-18-schnelle@linux.ibm.com
Signed-off-by: Lee Jones <lee@kernel.org>
The call netdev_{put, hold} of dev_{put, hold} will check NULL,
so there is no need to check before using dev_{put, hold},
remove it to silence the warnings:
./drivers/leds/trigger/ledtrig-netdev.c:291:3-10: WARNING: NULL check before dev_{put, hold} functions is not needed.
./drivers/leds/trigger/ledtrig-netdev.c:401:2-9: WARNING: NULL check before dev_{put, hold} functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=4929
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230511070820.52731-1-yang.lee@linux.alibaba.com
Signed-off-by: Lee Jones <lee@kernel.org>
Not all triggers use LED_INIT_DEFAULT_TRIGGER, which means that it
will not get cleared when the default trigger is a trigger which
does not use it such as "default-on".
If the default trigger then later gets replaced by a trigger which
does check LED_INIT_DEFAULT_TRIGGER, such as "timer" then that trigger
will behave as if it is the default trigger which it should not do.
To fix this clear the LED_INIT_DEFAULT_TRIGGER flag when clearing
the current trigger, so that it will not be set for any subsequently
set (non default) triggers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-5-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_trigger_blink() calls led_blink_set() from a RCU read-side critical
section so led_blink_set() must not sleep. Note sleeping was not allowed
before the switch to RCU either because a spinlock was held before.
led_blink_set() does not sleep when sw-blinking is used, but
many LED controller drivers with hw blink support have a blink_set
function which may sleep, leading to an oops like this one:
[ 832.605062] ------------[ cut here ]------------
[ 832.605085] Voluntary context switch within RCU read-side critical section!
[ 832.605119] WARNING: CPU: 2 PID: 370 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch+0x4ee/0x690
<snip>
[ 832.606453] Call Trace:
[ 832.606466] <TASK>
[ 832.606487] __schedule+0x9f/0x1480
[ 832.606527] schedule+0x5d/0xe0
[ 832.606549] schedule_timeout+0x79/0x140
[ 832.606572] ? __pfx_process_timeout+0x10/0x10
[ 832.606599] wait_for_completion_timeout+0x6f/0x140
[ 832.606627] i2c_dw_xfer+0x101/0x460
[ 832.606659] ? psi_group_change+0x168/0x400
[ 832.606680] __i2c_transfer+0x172/0x6d0
[ 832.606709] i2c_smbus_xfer_emulated+0x27d/0x9c0
[ 832.606732] ? __schedule+0x430/0x1480
[ 832.606753] ? preempt_count_add+0x6a/0xa0
[ 832.606778] ? get_nohz_timer_target+0x18/0x190
[ 832.606796] ? lock_timer_base+0x61/0x80
[ 832.606817] ? preempt_count_add+0x6a/0xa0
[ 832.606842] __i2c_smbus_xfer+0xa2/0x3f0
[ 832.606862] i2c_smbus_xfer+0x66/0xf0
[ 832.606882] i2c_smbus_read_byte_data+0x41/0x70
[ 832.606901] ? _raw_spin_unlock_irqrestore+0x23/0x40
[ 832.606922] ? __pm_runtime_suspend+0x46/0xc0
[ 832.606946] cht_wc_byte_reg_read+0x2e/0x60
[ 832.606972] _regmap_read+0x5c/0x120
[ 832.606997] _regmap_update_bits+0x96/0xc0
[ 832.607023] regmap_update_bits_base+0x5b/0x90
[ 832.607053] cht_wc_leds_brightness_get+0x412/0x910 [leds_cht_wcove]
[ 832.607094] led_blink_setup+0x28/0x100
[ 832.607119] led_trigger_blink+0x40/0x70
[ 832.607145] power_supply_update_leds+0x1b7/0x1c0
[ 832.607174] power_supply_changed_work+0x67/0xe0
[ 832.607198] process_one_work+0x1c8/0x3c0
[ 832.607222] worker_thread+0x4d/0x380
[ 832.607243] ? __pfx_worker_thread+0x10/0x10
[ 832.607258] kthread+0xe9/0x110
[ 832.607279] ? __pfx_kthread+0x10/0x10
[ 832.607300] ret_from_fork+0x2c/0x50
[ 832.607337] </TASK>
[ 832.607344] ---[ end trace 0000000000000000 ]---
Add a new led_blink_set_nosleep() function which defers the actual
led_blink_set() call to a workqueue when necessary to fix this.
This also fixes an existing race where a pending led_set_brightness() has
been deferred to set_brightness_work and might then race with a later
led_cdev->blink_set() call. Note this race is only an issue with triggers
mixing led_trigger_event() and led_trigger_blink() calls, sysfs API
calls and led_trigger_blink_oneshot() are not affected.
Note rather then adding a separate blink_set_blocking callback this uses
the presence of the already existing brightness_set_blocking callback to
detect if the blinking call should be deferred to set_brightness_work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When a trigger wants to switch from blinking to LED on it needs to call:
led_set_brightness(LED_OFF);
led_set_brightness(LED_FULL);
To first call disables blinking and the second then turns the LED on
(the power-supply charging-blink-full-solid triggers do this).
These calls happen immediately after each other, so it is possible
that set_brightness_delayed() from the first call has not run yet
when the led_set_brightness(LED_FULL) call finishes.
If this race hits then this is causing problems for both
sw- and hw-blinking:
For sw-blinking set_brightness_delayed() clears delayed_set_value
when LED_BLINK_DISABLE is set causing the led_set_brightness(LED_FULL)
call effects to get lost when hitting the race, resulting in the LED
turning off instead of on.
For hw-blinking if the race hits delayed_set_value has been
set to LED_FULL by the time set_brightness_delayed() runs.
So led_cdev->brightness_set_blocking() is never called with
LED_OFF as argument and the hw-blinking is never disabled leaving
the LED blinking instead of on.
Fix both issues by adding LED_SET_BRIGHTNESS and LED_SET_BRIGHTNESS_OFF
work_flags making this 2 separate actions to be run by
set_brightness_delayed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Link: https://lore.kernel.org/r/20230510162234.291439-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
led_blink_set[_oneshot]()'s delay_on and delay_off function parameters
are pass by reference, so that hw-blink implementations can report
back the actual achieved delays when the values have been rounded
to something the hw supports.
This is really only interesting for the sysfs API / the timer trigger.
Other triggers don't really care about this and none of the callers of
led_trigger_blink[_oneshot]() do anything with the returned delay values.
Change the led_trigger_blink[_oneshot]() delay parameters to pass-by-value,
there are 2 reasons for this:
1. led_cdev->blink_set() may sleep, while led_trigger_blink() may not.
So on hw where led_cdev->blink_set() sleeps the call needs to be deferred
to a workqueue, in which case the actual achieved delays are unknown
(this is a preparation patch for the deferring).
2. Since the callers don't care about the actual achieved delays, allowing
callers to directly pass a value leads to simpler code for most callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517180559.166329-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Lee Jones <lee@kernel.org>
Currently, LEDS_LM3697 and LEDS_LM36274 depend on LEDS_TI_LMU_COMMON,
which contains the common code to support TI LMU devices. This means
the user is asked about the common code first, followed by the
individual drivers, if their dependencies are met.
Simplify this, and reduce the number of questions by making
LEDS_TI_LMU_COMMON invisible, and letting it be selected when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@ucw.cz>
Link: https://lore.kernel.org/r/91f6efaa48c36320e58b6a312025ae9b39ee206b.1683644796.git.geert+renesas@glider.be
Signed-off-by: Lee Jones <lee@kernel.org>
The Qualcomm PMI8998 PMIC requires the LED to be disabled when configuring
the brightness. Always disable the LED when setting the brightness and
re-enable it afterwards.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-3-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
Add subtype for the Qualcomm PMI8998 PMIC to support it besides the
PM8150 PMIC which has the same registers. Adjust the driver to recognize
both PMIC subtypes as a 3 channel LED driver.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Link: https://lore.kernel.org/r/20230507172941.364852-2-me@dylanvanassche.be
Signed-off-by: Lee Jones <lee@kernel.org>
The desired default behavior of LED1 / the charge LED is breathing
while charging and on/solid when full. Since triggers cannot select
breathing, blink_set() gets called when charging. Use breathing
when the default "charging-blink-full-solid" trigger is used to
achieve the desired default behavior.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-6-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
be used for a hw-breathing effect.
As discussed during review of v2 of the submission of the new
leds-cht-wcove driver, the LED subsystem already supports breathing mode
on several other LED controllers using the hw_pattern interface.
Implement a pattern_set callback to implement breathing mode modelled
after the breathing mode supported by the SC27xx breathing light and
Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
is closer to the EL15203000 one then to the SC27xx one since it does
not support staying high / low for a specific time, it only supports
rise and fall times.
As such the supported hw_pattern and the documentation for this is almost
a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.
Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-4-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
When LED1 is showing the tablet is charging and then the device gets
suspended followed by unplugging the charger, then it will incorrectly
still show it is charging.
To avoid this turn both LEDs off on suspend, just like the PMIC always
turns them off when the tablet is powered off (even if the tablet is
charging). If hw-control is supported for LED1, then restore the
initial hw-control settings to let the hw control LED1 while suspended.
To restore the state the LEDs had before suspending, save it before
turning the LEDs off and restore it on resume.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-3-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.
This driver was tested with Lenovo Yoga Book notebook.
Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
the LED settings are permanent, even surviving reboot / poweroff.
Save LED1 register settings on probe() and if auto-/hw-control was
enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230430195952.862527-2-hdegoede@redhat.com
Signed-off-by: Lee Jones <lee@kernel.org>
The PMI632 PMIC contains 5 PWM channels, 3 of which can be used for
LEDs.
For the LED pattern it doesn't have LUT like other PMICs but uses SDAM
instead. This is not currently implemented in the driver but since LPG
works fine without it, add support for the PMIC now.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230414-pmi632-v2-4-98bafa909c36@z3ntu.xyz
The LP55xx range of devices have an internal charge pump which
can (automatically) increase the output voltage towards the
LED's, boosting the output voltage to 4.5V.
Implement this option from the devicetree. When the setting
is not present it will operate in automatic mode as before.
Tested on LP55231. Datasheet analysis shows that LP5521, LP5523
and LP8501 are identical in topology and are modified in the
same way.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230421075305.37597-3-maarten.zanders@mind.be
Some LEDs may require to sleep while doing some operation like setting
brightness and other cleanup.
For this reason, using a spinlock will cause a sleep under spinlock
warning.
It should be safe to convert this to a sleepable lock since:
- sysfs read/write can sleep
- netdev_trig_work is a work queue and can sleep
- netdev _trig_notify can sleep
The spinlock was used when brightness didn't support sleeping, but this
changed and now it supported with brightness_set_blocking().
Convert to mutex lock to permit sleeping using brightness_set_blocking().
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-6-ansuelsmth@gmail.com
Convert link tx and rx device attr to a common macro to reduce common
code and in preparation for additional attr.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-5-ansuelsmth@gmail.com
Rename NETDEV trigger enum modes to a more symbolic name and add a
namespace to them.
Also add __TRIGGER_NETDEV_MAX to identify the max modes of the netdev
trigger.
This is a cleanup to drop the define and no behaviour change are
intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-4-ansuelsmth@gmail.com
Putting NETDEV_LED_MODE_LINKUP in the same list of the netdev trigger
modes is wrong as it's used to set the link state of the device and not
to set a blink mode as it's done by NETDEV_LED_LINK, NETDEV_LED_TX and
NETDEV_LED_RX. It's also wrong to put this state in the same bitmap of the
netdev trigger mode and should be external to it.
Drop NETDEV_LED_MODE_LINKUP from mode list and convert to a simple bool
that will be true or false based on the carrier link. No functional
change intended.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-3-ansuelsmth@gmail.com
Dev can be renamed also while up for supported device. We currently
wrongly clear the NETDEV_LED_MODE_LINKUP flag on NETDEV_CHANGENAME
event.
Fix this by rechecking if the carrier is ok on NETDEV_CHANGENAME and
correctly set the NETDEV_LED_MODE_LINKUP bit.
Fixes: 5f820ed523 ("leds: trigger: netdev: fix handling on interface rename")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419210743.3594-2-ansuelsmth@gmail.com
- Add support for MediaTek MT6370 LED Indicator
- Add support for MediaTek MT6370 Flashlight
- Add support for QCOM PMIC Flash
- Add support for Rohm BD2606MVV Charge Pump LED
- New Device Support
- Add support for PMK8550 PWM to QCOM LPG
- New Functionality
- Add support for high resolution PWM to QCOM LPG
- Fix-ups
- Kconfig 'depends' and 'select' dependency changes
- Remove unused / irrelevant includes
- Remove unnecessary checks (already performed further into the call stack)
- Trivial: Fix commentary, simplify error messages
- Rid 'defined but not used' warnings
- Provide documentation
- Explicitly provide include files
- Bug Fixes
- Mark GPIO LED as BROKEN
- Fix Kconfig entries
- Fix various Smatch staticify reports
- Fix error handling (or a lack there of)
-----BEGIN PGP SIGNATURE-----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=aJQw
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for MediaTek MT6370 LED Indicator
- Add support for MediaTek MT6370 Flashlight
- Add support for QCOM PMIC Flash
- Add support for Rohm BD2606MVV Charge Pump LED
New Device Support:
- Add support for PMK8550 PWM to QCOM LPG
New Functionality:
- Add support for high resolution PWM to QCOM LPG
Fix-ups:
- Kconfig 'depends' and 'select' dependency changes
- Remove unused / irrelevant includes
- Remove unnecessary checks (already performed further into the call stack)
- Trivial: Fix commentary, simplify error messages
- Rid 'defined but not used' warnings
- Provide documentation
- Explicitly provide include files
Bug Fixes:
- Mark GPIO LED as BROKEN
- Fix Kconfig entries
- Fix various Smatch staticify reports
- Fix error handling (or a lack there of)"
* tag 'leds-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (30 commits)
leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
dt-bindings: leds: Add ROHM BD2606MVV LED
docs: leds: ledtrig-oneshot: Fix spelling mistake
leds: pwm-multicolor: Simplify an error message
dt-bindings: leds: Convert PCA9532 to dtschema
leds: rgb: leds-qcom-lpg: Add support for PMK8550 PWM
leds: rgb: leds-qcom-lpg: Add support for high resolution PWM
dt-bindings: leds-qcom-lpg: Add qcom,pmk8550-pwm compatible string
leds: tca6507: Fix error handling of using fwnode_property_read_string
leds: flash: Set variables mvflash_{3,4}ch_regs storage-class-specifier to static
leds: rgb: mt6370: Correct config name to select in LEDS_MT6370_RGB
MAINTAINERS: Add entry for LED devices documentation
Documentation: leds: MT6370: Use bullet lists for timing variables
Documentation: leds: mt6370: Properly wrap hw_pattern chart
Documentation: leds: Add MT6370 doc to the toctree
leds: rgb: mt6370: Fix implicit declaration for FIELD_GET
docs: leds: Add MT6370 RGB LED pattern document
leds: flash: mt6370: Add MediaTek MT6370 flashlight support
leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support
dt-bindings: leds: spmi-flash-led: Add pm6150l compatible
...
The device provides 6 channels which can be individually
turned off and on but groups of two channels share a common brightness
register.
Limitation: The GPIO to enable the device is not used yet.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230419111806.1100437-3-andreas@kemnade.info
Certain PMICs like PMK8550 have a high resolution PWM module which can
support from 8-bit to 15-bit PWM. Add support for it.
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230407223849.17623-3-quic_amelende@quicinc.com
Commit 96f524105b ("leds: tca6507: use fwnode API instead of OF")
changed to fwnode API but did not take into account that a missing property
"linux,default-trigger" now seems to return an error and as a side effect
sets value to -1. This seems to be different from of_get_property() which
always returned NULL in any case of error.
Neglecting this side-effect leads to
[ 11.201965] Unable to handle kernel paging request at virtual address ffffffff when read
in the strcmp() of led_trigger_set_default() if there is no led-trigger
defined in the DTS.
I don't know if this was recently introduced somewhere in the fwnode lib
or if the effect was missed in initial testing. Anyways it seems to be a
bug to ignore the error return value of an optional value here in the
driver.
Fixes: 96f524105b ("leds: tca6507: use fwnode API instead of OF")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/cbae7617db83113de726fcc423a805ebaa1bfca6.1680433978.git.hns@goldelico.com
Smatch reports:
drivers/leds/flash/leds-qcom-flash.c:103:18: warning:
symbol 'mvflash_3ch_regs' was not declared. Should it be static?
drivers/leds/flash/leds-qcom-flash.c:115:18: warning:
symbol 'mvflash_4ch_regs' was not declared. Should it be static?
These variables are only used locally, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230317191341.1670660-1-trix@redhat.com
Commit 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink
type LED Indicator support") introduces the config LEDS_MT6370_RGB, which
selects the non-existing config LINEAR_RANGE. As the driver includes
linux/linear_range.h, it is a safe guess that the config actually intends
to select LINEAR_RANGES, which provides the library implementation for the
function prototypes defined in the linear_range header file.
Correct this naming confusion in the LEDS_MT6370_RGB config definition.
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230323105410.10396-1-lukas.bulwahn@gmail.com
0-DAY CI Kernel Test Service reported the implicit declaration error below:
drivers/leds/rgb/leds-mt6370-rgb.c: In function'mt6370_check_vendor_info':
>> drivers/leds/rgb/leds-mt6370-rgb.c:889:15: error: implicit declaration
of function 'FIELD_GET' [-Werror=implicit-function-declaration]
889 | vid = FIELD_GET(MT6370_VENDOR_ID_MASK, devinfo);
|
Add the missing header 'bitfield.h' to fix it.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202303171729.CcgyFx17-lkp@intel.com/
Fixes: 55a8a5c16eb3 ("leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support")
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1679067760-19098-1-git-send-email-cy_huang@richtek.com
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual Flash
LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MT6370 Flash LED driver. Flash LED in MT6370
has 2 channels and support torch/strobe mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/52480420a160e5a4c71715fbbf105e684a16e7c2.1678430444.git.chiaen_wu@richtek.com
The MediaTek MT6370 is a highly-integrated smart power management IC,
which includes a single cell Li-Ion/Li-Polymer switching battery
charger, a USB Type-C & Power Delivery (PD) controller, dual
Flash LED current sources, a RGB LED driver, a backlight WLED driver,
a display bias driver and a general LDO for portable devices.
Add support for the MediaTek MT6370 Current Sink Type LED Indicator
driver. It can control four channels current-sink RGB LEDs with 3 modes:
constant current, PWM, and breath mode.
Co-developed-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: Alice Chen <alice_chen@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/1df93a583c3f508a7158b83b95857e9bce235e1b.1678430444.git.chiaen_wu@richtek.com
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add initial driver to support flash LED module found in Qualcomm
Technologies, Inc. PMICs. The flash module can have 3 or 4 channels
and each channel can be controlled indepedently and support full scale
current up to 1.5 A. It also supports connecting two channels together
to supply one LED component with full scale current up to 2 A. In that
case, the current will be split on each channel symmetrically and the
channels will be enabled and disabled at the same time.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sm7225-fairphone-fp4 + pm6150l
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230303095023.538917-2-quic_fenglinw@quicinc.com
The GPIO LED trigger exposes a userspace ABI where a user
can echo a GPIO number from the global GPIO numberspace into
a file that will trigger a certain LED when active.
This is problematic because the global GPIO numberspace is
inherently instable. The trigger came about at a time when
systems had one GPIO controller that defined hard-wired
GPIOs numbered 0..N and this number space was stable.
We have since moved to dynamic allocation of GPIO numbers
and there is no real guarantee that a GPIO number will stay
consistent even across a reboot: consider a USB attached
GPIO controller for example. Or two. Or the effect of
probe order after adding -EPROBE_DEFER to the kernel.
The trigger was added to support keypad LEDs on the Nokia
n810 from the GPIO event when a user slides up/down the
keypad. This is arch/arm/boot/dts/omap2420-n810.dts.
A userspace script is needed to activate the trigger.
This will be broken unless the script was updated recently
since the OMAP GPIO controller now uses dynamic GPIO
number allocations.
I want to know that this trigger has active users that
cannot live without it if we are to continue to support it.
Option if this is really needed: I can develop a new trigger
that can associate GPIOs with LEDs as triggers using device
tree, which should also remove the use of userspace custom
scripts to achieve this and be much more trustworthy, if
someone with the Nokia n810 or a device with a similar need
is willing to test it.
Suggested-by Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230314210059.419159-1-linus.walleij@linaro.org
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/leds/leds-tlc591xx.c:138:34: error: ‘of_tlc591xx_leds_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230311111717.252019-1-krzysztof.kozlowski@linaro.org
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 3fce8e1eb9 ("leds: TI LMU: Add common code for TI LMU devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230226053953.4681-5-rdunlap@infradead.org
- HTC ASIC3 LED
- New Functionality
- Provide generic led_get() which can be used by both DT and !DT platforms
- Fix-ups
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
- Bug Fixes
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before processing next child
- Fix Clang's warning about incompatible function types when using devm_add_action*()
-----BEGIN PGP SIGNATURE-----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=bbUo
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"Removed Drivers:
- HTC ASIC3 LED
New Functionality:
- Provide generic led_get() which can be used by both DT and !DT
platforms
Fix-ups:
- Convert a bunch of I2C subsystem users to the new probing API
- Explicitly provide missing include files
- Make use of led_init_default_state_get() and rid the custom
variants
- Use simplified fwnode_device_is_compatible() API
- Provide some Device Tree additions / adaptions
- Fix some trivial spelling issues
Bug Fixes:
- Prevent device refcount leak during led_put() and of_led_get()
- Clear previous data from temporary led_pwm structure before
processing next child
- Fix Clang's warning about incompatible function types when using
devm_add_action*()"
* tag 'leds-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (41 commits)
leds: Remove ide-disk trigger
dt-bindings: leds: Add disk write/read and usb-host/usb-gadget
Documentation: leds: Correct spelling
dt-bindings: leds: Document Bluetooth and WLAN triggers
leds: Remove asic3 driver
leds: simatic-ipc-leds-gpio: Make sure we have the GPIO providing driver
leds: tca6507: Convert to use fwnode_device_is_compatible()
leds: syscon: Get rid of custom led_init_default_state_get()
leds: pm8058: Get rid of custom led_init_default_state_get()
leds: pca955x: Get rid of custom led_init_default_state_get()
leds: mt6360: Get rid of custom led_init_default_state_get()
leds: mt6323: Get rid of custom led_init_default_state_get()
leds: bcm6358: Get rid of custom led_init_default_state_get()
leds: bcm6328: Get rid of custom led_init_default_state_get()
leds: an30259a: Get rid of custom led_init_default_state_get()
leds: Move led_init_default_state_get() to the global header
leds: Add missing includes and forward declarations in leds.h
leds: is31fl319x: Wrap mutex_destroy() for devm_add_action_or_rest()
leds: turris-omnia: Convert to i2c's .probe_new()
leds: tlc591xx: Convert to i2c's .probe_new()
...
Highlights:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
The following is an automated git shortlog grouped by driver:
Add include/linux/platform_data/x86 to MAINTAINERS:
- Add include/linux/platform_data/x86 to MAINTAINERS
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix header inclusion in linux/platform_data/x86/soc.h:
- Fix header inclusion in linux/platform_data/x86/soc.h
HID:
- surface-hid: Use target-ID enum instead of hard-coding values
MAINTAINERS:
- dell-wmi-sysman: drop Divya Bharathi
- Add entry for TPMI driver
Merge tag 'ib-leds-led_get-v6.3' into HEAD:
- Merge tag 'ib-leds-led_get-v6.3' into HEAD
acerhdf:
- Drop empty platform remove function
apple_gmux:
- Drop no longer used ACPI_VIDEO Kconfig dependency
dell-ddv:
- Prefer asynchronous probing
- Add hwmon support
- Add "force" module param
- Replace EIO with ENOMSG
- Return error if buffer is empty
- Add support for interface version 3
dell-smo8800:
- Use min_t() for comparison and assignment
dell-wmi-sysman:
- Make kobj_type structure constant
hp-wmi:
- Ignore Win-Lock key events
int1092:
- Switch to use acpi_evaluate_dsm_typed()
int3472/discrete:
- add LEDS_CLASS dependency
- Drop unnecessary obj->type == string check
- Get the polarity from the _DSM entry
- Move GPIO request to skl_int3472_register_clock()
- Create a LED class device for the privacy LED
- Refactor GPIO to sensor mapping
intel:
- punit_ipc: Drop empty platform remove function
- oaktrail: Drop empty platform remove function
intel/pmc:
- Switch to use acpi_evaluate_dsm_typed()
leds:
- led-class: Add generic [devm_]led_get()
- led-class: Add __devm_led_get() helper
- led-class: Add led_module_get() helper
- led-class: Add missing put_device() to led_put()
media:
- v4l2-core: Make the v4l2-core code enable/disable the privacy LED if present
nvidia-wmi-ec-backlight:
- Add force module parameter
platform:
- mellanox: mlx-platform: Move bus shift assignment out of the loop
- mellanox: mlx-platform: Add mux selection register to regmap
- mellanox: Extend all systems with I2C notification callback
- mellanox: Split logic in init and exit flow
- mellanox: Split initialization procedure
- mellanox: Introduce support of new Nvidia L1 switch
- mellanox: Introduce support for next-generation 800GB/s switch
- mellanox: Cosmetic changes - rename to more common name
- mellanox: Change "reset_pwr_converter_fail" attribute
- mellanox: Introduce support for rack manager switch
platform/mellanox:
- mlxreg-hotplug: Allow more flexible hotplug events configuration
platform/surface:
- Switch to use acpi_evaluate_dsm_typed()
- aggregator: Rename top-level request functions to avoid ambiguities
- aggregator_registry: Fix target-ID of base-hub
- aggregator: Enforce use of target-ID enum in device ID macros
- dtx: Use target-ID enum instead of hard-coding values
- aggregator_tabletsw: Use target-ID enum instead of hard-coding values
- aggregator_hub: Use target-ID enum instead of hard-coding values
- aggregator: Add target and source IDs to command trace events
- aggregator: Improve documentation and handling of message target and source IDs
platform/x86/amd:
- pmc: Add line break for readability
- pmc: differentiate STB/SMU messaging prints
- pmc: Write dummy postcode into the STB DRAM
- pmc: Add num_samples message id support to STB
platform/x86/amd/pmf:
- Add depends on CONFIG_POWER_SUPPLY
platform/x86/intel:
- Intel TPMI enumeration driver
platform/x86/intel/tpmi:
- ADD tpmi external interface for tpmi feature drivers
- Process CPU package mapping
platform/x86/intel/vsec:
- Use mutex for ida_alloc() and ida_free()
- Support private data
- Enhance and Export intel_vsec_add_aux()
- Add TPMI ID
platform_data/mlxreg:
- Add field with mapped resource address
think-lmi:
- Make kobj_type structure constant
- Use min_t() for comparison and assignment
tools/power/x86/intel-speed-select:
- v1.14 release
- Adjust uncore max/min frequency
- Add Emerald Rapid quirk
- Fix display of uncore min frequency
- turbo-freq auto mode with SMT off
- cpufreq reads on offline CPUs
- Use null-terminated string
- Remove duplicate dup()
- Handle open() failure case
- Remove unused non_block flag
- Remove wrong check in set_isst_id()
x86/platform/uv:
- Make kobj_type structure constant
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmPzRpgUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9wYPwf+I6PP0XBg8MrivLc2DHklVojUU0aX
/M0LbCP8gxCDdyisV8swC3e848riaTchYlUGASPZu0ieas1U7KsDvghkiittNvlI
U+0h7TbkOQNymM8oE0oauflH4W5KwCXGrLsJWVkGk0lhJd6WmjXkjWLkruaXazLd
kc5fq0QyzRVzhhCtocQ7qhIgXSZyKYx433VqbDR7/SUi5F2wkC9JbGY02maKWaK3
4lQaoyMKLjGlDr9YVv+UHTwLoXwP0mW/fjlsZ3Xz5lz6WfihQzPuOrl/10mRj0Ez
eP9dlF1Dipee4BYS2FM5dtk5xPpqdVqRlQUX2qKzyDNTSx5wdtJnv8j/cg==
=VoXq
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- AMD PMC: Improvements to aid s2idle debugging
- Dell WMI-DDV: hwmon support
- INT3472 camera sensor power-management: Improve privacy LED support
- Intel VSEC: Base TPMI (Topology Aware Register and PM Capsule
Interface) support
- Mellanox: SN5600 and Nvidia L1 switch support
- Microsoft Surface Support: Various cleanups + code improvements
- tools/intel-speed-select: Various improvements
- Miscellaneous other cleanups / fixes
* tag 'platform-drivers-x86-v6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (80 commits)
platform/x86: nvidia-wmi-ec-backlight: Add force module parameter
platform/x86/amd/pmf: Add depends on CONFIG_POWER_SUPPLY
platform/x86: dell-ddv: Prefer asynchronous probing
platform/x86: dell-ddv: Add hwmon support
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform: mellanox: mlx-platform: Move bus shift assignment out of the loop
platform: mellanox: mlx-platform: Add mux selection register to regmap
platform_data/mlxreg: Add field with mapped resource address
platform/mellanox: mlxreg-hotplug: Allow more flexible hotplug events configuration
platform: mellanox: Extend all systems with I2C notification callback
platform: mellanox: Split logic in init and exit flow
platform: mellanox: Split initialization procedure
platform: mellanox: Introduce support of new Nvidia L1 switch
platform: mellanox: Introduce support for next-generation 800GB/s switch
platform: mellanox: Cosmetic changes - rename to more common name
platform: mellanox: Change "reset_pwr_converter_fail" attribute
platform: mellanox: Introduce support for rack manager switch
MAINTAINERS: dell-wmi-sysman: drop Divya Bharathi
x86/platform/uv: Make kobj_type structure constant
platform/x86: think-lmi: Make kobj_type structure constant
...
No user of ide-disk remains, so remove this deprecated trigger.
Only a few platforms used this and were fixed in 2016.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131140304.626779-2-clabbe@baylibre.com
If we register a "leds-gpio" platform device for GPIO pins that do not
exist we get a -EPROBE_DEFER and the probe will be tried again later.
If there is no driver to provide that pin we will poll forever and also
create a lot of log messages.
So check if that GPIO driver is configured, if so it will come up
eventually. If not, we exit our probe function early and do not even
bother registering the "leds-gpio". This method was chosen over "Kconfig
depends" since this way we can add support for more devices and GPIO
backends more easily without "depends":ing on all GPIO backends.
Fixes: a6c80bec3c ("leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver")
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221007153323.1326-1-henning.schild@siemens.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-8-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-7-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-6-andriy.shevchenko@linux.intel.com
LED core provides a helper to parse default state from firmware node.
Use it instead of custom implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-5-andriy.shevchenko@linux.intel.com
There are users inside and outside LED framework that have implemented
a local copy of led_init_default_state_get(). In order to deduplicate
that, as the first step move the declaration from LED header to the
global one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230103131256.33894-3-andriy.shevchenko@linux.intel.com
Clang complains that devm_add_action() takes a parameter with a wrong type:
warning: cast from 'void (*)(struct mutex *)' to 'void (*)(void *)' converts to incompatible function type [-Wcast-function-type-strict]
err = devm_add_action(dev, (void (*)(void *))mutex_destroy, &is31->lock);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1 warning generated.
It appears that the commit e1af5c8155 ("leds: is31fl319x: Fix devm vs.
non-devm ordering") missed two things:
- whilst the commit mentions devm_add_action_or_reset() the actual change
utilised devm_add_action() call by mistake
- strictly speaking the parameter is not compatible by type
Fix both issues by switching to devm_add_action_or_reset() and adding a
wrapper for mutex_destroy() call.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e1af5c8155 ("leds: is31fl319x: Fix devm vs. non-devm ordering")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221228093238.82713-1-andriy.shevchenko@linux.intel.com
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-289-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-286-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-285-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-283-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-281-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-280-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-276-uwe@kleine-koenig.org
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-274-uwe@kleine-koenig.org
class_find_device_by_of_node() calls class_find_device(), it will take
the reference, use the put_device() to drop the reference when not need
anymore.
Fixes: 699a8c7c4b ("leds: Add of_led_get() and led_put()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221220121807.1543790-1-linmq006@gmail.com
I defined 2 leds in the device tree, in the 1st led node, the
max-brightness is set to 248, while in the 2nd led node, I
mis-spelled the max-brightness to max-brighttness, but the driver
is still able to get the max-brightness 248 for the 2nd node, that
is because the led structure is not cleared before parsing each child
node.
pwmleds {
compatible = "pwm-leds";
pwm-green {
...
max-brightness = <248>;
};
pwm-red {
...
max-brighttness = <128>;
};
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221220073335.393489-1-hui.wang@canonical.com
Add a generic [devm_]led_get() method which can be used on both devicetree
and non devicetree platforms to get a LED classdev associated with
a specific function on a specific device, e.g. the privacy LED associated
with a specific camera sensor.
Note unlike of_led_get() this takes a string describing the function
rather then an index. This is done because e.g. camera sensors might
have a privacy LED, or a flash LED, or both and using an index
approach leaves it unclear what the function of index 0 is if there is
only 1 LED.
This uses a lookup-table mechanism for non devicetree platforms.
This allows the platform code to map specific LED class_dev-s to a specific
device,function combinations this way.
For devicetree platforms getting the LED by function-name could be made
to work using the standard devicetree pattern of adding a -names string
array to map names to the indexes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120114524.408368-5-hdegoede@redhat.com
Add a __devm_led_get() helper which registers a passed in led_classdev
with devm for unregistration.
This is a preparation patch for adding a generic (non devicetree specific)
devm_led_get() function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120114524.408368-4-hdegoede@redhat.com
Split out part of of_led_get() into a generic led_module_get() helper
function.
This is a preparation patch for adding a generic (non devicetree specific)
led_get() function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120114524.408368-3-hdegoede@redhat.com
led_put() is used to "undo" a successful of_led_get() call,
of_led_get() uses class_find_device_by_of_node() which returns
a reference to the device which must be free-ed with put_device()
when the caller is done with it.
Add a put_device() call to led_put() to free the reference returned
by class_find_device_by_of_node().
And also add a put_device() in the error-exit case of try_module_get()
failing.
Fixes: 699a8c7c4b ("leds: Add of_led_get() and led_put()")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120114524.408368-2-hdegoede@redhat.com
The s3c24xx platform is gone, so the led driver can be
removed as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various changes across the board, mostly improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=IM51
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
lot. Plus, there are some bugfixes as a bonus.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCY5xICAAKCRAw5/Bqldv6
8nkhAJ9lqVnS7+m2eq5w1gQlgd2ToktRaQCfcj7WPznJCe3dPVpwSsWxa//B1Rw=
=B8QS
-----END PGP SIGNATURE-----
Merge tag 'leds-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Lee Jones offered his help with maintaining LEDs, thanks a lot.
Plus, there are some bugfixes as a bonus"
* tag 'leds-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: MAINTAINERS: include dt-bindings headers
leds: qcom,pm8058-led: Convert to DT schema
leds: use sysfs_emit() to instead of scnprintf()
leds: is31fl319x: Fix setting current limit for is31fl319{0,1,3}
MAINTAINERS: Add additional co-maintainer to LEDs
leds: lp5523: fix out-of-bounds bug in lp5523_selftest()
dt-bindings: leds: Add 'cpuX' to 'linux,default-trigger'
led: qcom-lpg: Fix sleeping in atomic
leds: max8997: Don't error if there is no pdata
leds: lp55xx: remove variable j
leds-pca955x: Remove the unused function pca95xx_num_led_regs()
GPIO core:
- teach gpiolib to work with software nodes for HW description
- remove ARCH_NR_GPIOS treewide as we no longer impose any limit on the number
of GPIOS since the allocation became entirely dynamic
- add support for HW quirks for Cirrus CS42L56 codec, Marvell NFC controller,
Freescale PCIe and Ethernet controller, Himax LCDs and Mediatek mt2701
- refactor OF quirk code
- some general refactoring of the OF and ACPI code, adding new helpers, minor
tweaks and fixes, making fwnode usage consistent etc.
GPIO uAPI:
- fix an issue where the user-space can trigger a NULL-pointer dereference in
the kernel by opening a device file, forcing a driver unbind and then calling
one of the syscalls on the associated file descriptor
New drivers:
- add gpio-latch: a new GPIO multiplexer based on latches connected to other
GPIOs
Driver updates:
- convert i2c GPIO expanders to using .probe_new()
- drop the gpio-sta2x11 driver
- factor out common code for the ACCES IDIO-16 family of controllers and use
this new library wherever applicable in drivers
- add DT support to gpio-hisi
- allow building gpio-davinci as a module and increase its maxItems property
- add support for a new model to gpio-pca9570
- other minor changes to various drivers
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmObAGkACgkQEacuoBRx
13Jrew//VWgqyLgfOysJ5hdVQigY3KGEPbai2nXQK58HFymdBer2MG/G27j0aw46
mEgwYcrDKO4fi08AzCXexF/JYFZha7s4EwujJ/uRmye7xtVgs1xlaPPhTtFV2Iky
P2994k1IhsScou5Tu9WZmHyeGLhiMleuBe+KbL4Xhfa1JYUhQymiQi8aiBGs7fW3
aMTtTa/7NpDl3YFNS+un7Ahuftj1CfwGYOiWeQy+Fy1UE5uE/UgvmiSYi/3rvrCQ
O/WVWgd26sTKyGb92nrbHjY2DPr5ULAC8aRY3JQ1pmfyPpTuqNUtb+CUYjP/oxqx
JjZms96YW7B7sL93SNWog+9ZyYr+jnfdg+ZgGDEZ1ViGXgoe/Fr+xs6tRwww8GL4
Bt3nAlAR/X2Udarlmep4Udca5BOr2kc7JmcVEvNrVJAI7wGxo3SKWdIWcgs43e0B
Ps3iJmdK4ndzHh4jrcZEzZUXpmOSHzpiW/YuqPd/9XNpJowhT2BObukRlAcVZqjf
PvyN2nktF45fqjuszBo0GK9QZv0DUofgkUxYgEpdIvLwfvodJVoFbK5KOI0Kqxfc
CJxuAgKgEI569iEguEj7+pF5c1VW5LWJRV2kG6XbxwXKn2c+47/HkvvrR34sLu9n
+7yp4x5BflVQiQsrbDfQiYXOz8jb8tWgn1o1LIQyYkUan4zCjjk=
=zg1O
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a new GPIO multiplexer driver, bunch of driver updates and
refactoring in the core GPIO library.
GPIO core:
- teach gpiolib to work with software nodes for HW description
- remove ARCH_NR_GPIOS treewide as we no longer impose any limit on
the number of GPIOS since the allocation became entirely dynamic
- add support for HW quirks for Cirrus CS42L56 codec, Marvell NFC
controller, Freescale PCIe and Ethernet controller, Himax LCDs and
Mediatek mt2701
- refactor OF quirk code
- some general refactoring of the OF and ACPI code, adding new
helpers, minor tweaks and fixes, making fwnode usage consistent
etc.
GPIO uAPI:
- fix an issue where the user-space can trigger a NULL-pointer
dereference in the kernel by opening a device file, forcing a
driver unbind and then calling one of the syscalls on the
associated file descriptor
New drivers:
- add gpio-latch: a new GPIO multiplexer based on latches connected
to other GPIOs
Driver updates:
- convert i2c GPIO expanders to using .probe_new()
- drop the gpio-sta2x11 driver
- factor out common code for the ACCES IDIO-16 family of controllers
and use this new library wherever applicable in drivers
- add DT support to gpio-hisi
- allow building gpio-davinci as a module and increase its maxItems
property
- add support for a new model to gpio-pca9570
- other minor changes to various drivers"
* tag 'gpio-updates-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (66 commits)
gpio: sim: set a limit on the number of GPIOs
gpiolib: protect the GPIO device against being dropped while in use by user-space
gpiolib: cdev: fix NULL-pointer dereferences
gpiolib: Provide to_gpio_device() helper
gpiolib: Unify access to the device properties
gpio: Do not include <linux/kernel.h> when not really needed.
gpio: pcf857x: Convert to i2c's .probe_new()
gpio: pca953x: Convert to i2c's .probe_new()
gpio: max732x: Convert to i2c's .probe_new()
dt-bindings: gpio: gpio-davinci: Increase maxItems in gpio-line-names
gpiolib: ensure that fwnode is properly set
gpio: sl28cpld: Replace irqchip mask_invert with unmask_base
gpiolib: of: Use correct fwnode for DT-probed chips
gpiolib: of: Drop redundant check in of_mm_gpiochip_remove()
gpiolib: of: Prepare of_mm_gpiochip_add_data() for fwnode
gpiolib: add support for software nodes
gpiolib: consolidate GPIO lookups
gpiolib: acpi: avoid leaking ACPI details into upper gpiolib layers
gpiolib: acpi: teach acpi_find_gpio() to handle data-only nodes
gpiolib: acpi: change acpi_find_gpio() to accept firmware node
...
Replace the open-code with sysfs_emit() to simplify the code.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The current setting lives in bits 4:2 (as also defined by the mask) but
the current limit defines in the driver use bits 2:0 which should be
shifted over so they don't get masked out completely (except for 17.5mA
which became 10mA).
Now checking /sys/kernel/debug/regmap/1-0068/registers shows that the
current limit is applied correctly and doesn't take the default b000 =
42mA.
Fixes: fa877cf1ab ("leds: is31fl319x: Add support for is31fl319{0,1,3} chips")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
.get_state() can return an error indication. Make use of it to propagate
failing hardware accesses.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
devm_fwnode_get_gpiod_from_child() is going away as the name is too
unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
devm_fwnode_get_gpiod_from_child() is going away as the name is too
unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
When not all LED channels of the led chip are configured, the
sysfs selftest functionality gives erroneous results and tries to
test all channels of the chip.
There is a potential for LED overcurrent conditions since the
test current will be set to values from out-of-bound regions.
It is wrong to use pdata->led_config[i].led_current to skip absent
channels as led_config[] only contains the configured LED channels.
Instead of iterating over all the physical channels of the device,
loop over the available LED configurations and use led->chan_nr to
access the correct i2c registers. Keep the zero-check for the LED
current as existing users might depend on this to disable a channel.
Reported-by: Arne Staessen <a.staessen@televic.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
For apollolake the mapping between LEDs and GPIO pins was off because of
a refactoring when we introduced a new device model.
In addition to the reordering the indices in the lookup table need to be
updated as well.
Fixes: a97126265d ("leds: simatic-ipc-leds-gpio: add new model 227G")
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20221024092027.4529-1-henning.schild@siemens.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The driver works just fine if no platform data is supplied.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The variable j being incremented but it is never referenced,
it is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The function pca95xx_num_led_regs() is defined in the leds-pca955x.c
file, but not called elsewhere, so delete this unused function.
drivers/leds/leds-pca955x.c:149:19: warning: unused function 'pca95xx_num_led_regs'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2411
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
that's pretty much it.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCY0leQwAKCRAw5/Bqldv6
8qGYAJwJ3HPp5PldDKtGr9+90yEJK4SFKgCfTOZenbAe/pESkCGnKJszvHdOupk=
=aZ15
-----END PGP SIGNATURE-----
Merge tag 'leds-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"This is very quiet release for LEDs, pca963 got blinking support and
that's pretty much it"
* tag 'leds-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: pca963: fix misleading indentation
dt-bindings: leds: Document mmc trigger
leds: pca963x: fix blink with hw acceleration
Highlights:
- AMD Platform Management Framework (PMF) driver with AMT and QnQF support
- AMD PMC: Improved logging for debugging s2idle issues
- Big refactor of the ACPI/x86 backlight handling, ensuring that we only
register 1 /sys/class/backlight device per LCD panel
- Microsoft Surface:
- Surface Laptop Go 2 support
- Surface Pro 8 HID sensor support
- Asus WMI:
- Lots of cleanups
- Support for TUF RGB keyboard backlight control
- Add support for ROG X13 tablet mode
- Siemens Simatic: IPC227G and IPC427G support
- Toshiba ACPI laptop driver: Fan hwmon and battery ECO mode support
- tools/power/x86/intel-speed-select: Various improvements
- Various cleanups
- Various small bugfixes
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Change disable_backlight_sysfs_if quirks to acpi_backlight=native
- s2idle: Add a new ->check() callback for platform_s2idle_ops
- video: Fix indentation of video_detect_dmi_table[] entries
- video: Drop NL5x?U, PF4NU1F and PF5?U?? acpi_backlight=native quirks
- video: Drop "Samsung X360" acpi_backlight=native quirk
- video: Remove acpi_video_set_dmi_backlight_type()
- video: Add Apple GMUX brightness control detection
- video: Add Nvidia WMI EC brightness control detection (v3)
- video: Refactor acpi_video_get_backlight_type() a bit
- video: Remove code to unregister acpi_video backlight when a native backlight registers
- video: Make backlight class device registration a separate step (v2)
- video: Simplify acpi_video_unregister_backlight()
- video: Remove acpi_video_bus from list before tearing it down
- video: Drop backlight_device_get_by_type() call from acpi_video_get_backlight_type()
- video: Add acpi_video_backlight_use_native() helper
acer-wmi:
- Move backlight DMI quirks to acpi/video_detect.c
- Acer Aspire One AOD270/Packard Bell Dot keymap fixes
apple-gmux:
- Stop calling acpi/video.h functions
asus-wmi:
- Expand support of GPU fan to read RPM and label
- Make kbd_rgb_mode_groups static
- Move acpi_backlight=native quirks to ACPI video_detect.c
- Move acpi_backlight=vendor quirks to ACPI video_detect.c
- Drop DMI chassis-type check from backlight handling
- Increase FAN_CURVE_BUF_LEN to 32
- Fix the name of the mic-mute LED classdev
- Implement TUF laptop keyboard power states
- Implement TUF laptop keyboard LED modes
- Support the GPU fan on TUF laptops
- Modify behaviour of Fn+F5 fan key
- Update tablet_mode_sw module-param help text
- Simplify tablet-mode-switch handling
- Simplify tablet-mode-switch probing
- Add support for ROG X13 tablet mode
- Adjust tablet/lidflip handling to use enum
- Support the hardware GPU MUX on some laptops
- Simplify some of the *_check_present() helpers
- Refactor panel_od attribute
- Refactor egpu_enable attribute
- Refactor disable_gpu attribute
- Document the panel_od sysfs attribute
- Document the egpu_enable sysfs attribute
- Document the dgpu_disable sysfs attribute
- Use kobj_to_dev()
- Convert all attr-show to use sysfs_emit
compal-laptop:
- Get rid of a few forward declarations
dell-privacy:
- convert to use dev_groups
dell-smbios-base:
- Use sysfs_emit()
dell-wmi:
- Add WMI event 0x0012 0x0003 to the list
docs:
- ABI: charge_control_end_threshold may not support all values
drivers/platform:
- toshiba_acpi: Call HCI_PANEL_POWER_ON on resume on some models
drm/amdgpu:
- Register ACPI video backlight when skipping amdgpu backlight registration
- Don't register backlight when another backlight should be used (v3)
drm/i915:
- Call acpi_video_register_backlight() (v3)
- Don't register backlight when another backlight should be used (v2)
drm/nouveau:
- Register ACPI video backlight when nv_backlight registration fails (v2)
- Don't register backlight when another backlight should be used (v2)
drm/radeon:
- Register ACPI video backlight when skipping radeon backlight registration
- Don't register backlight when another backlight should be used (v3)
drm/todo:
- Add entry about dealing with brightness control on devices with > 1 panel
gpio-f7188x:
- use unique labels for banks/chips
- Add GPIO support for Nuvoton NCT6116
- add a prefix to macros to keep gpio namespace clean
- switch over to using pr_fmt
hp-wmi:
- Support touchpad on/off
- Setting thermal profile fails with 0x06
int3472/discrete:
- Drop a forward declaration
intel-uncore-freq:
- Use sysfs_emit() to instead of scnprintf()
intel_cht_int33fe:
- Fix comment according to the code flow
leds:
- simatic-ipc-leds-gpio: Make simatic_ipc_led_gpio_table static
- simatic-ipc-leds-gpio: add new model 227G
move from strlcpy with unused retval to strscpy:
- move from strlcpy with unused retval to strscpy
msi-laptop:
- Change DMI match / alias strings to fix module autoloading
- Add msi_scm_disable_hw_fn_handling() helper
- Add msi_scm_model_exit() helper
- Fix resource cleanup
- Simplify ec_delay handling
- Fix old-ec check for backlight registering
- Drop MSI_DRIVER_VERSION
- Use MODULE_DEVICE_TABLE()
nvidia-wmi-ec-backlight:
- Use acpi_video_get_backlight_type()
- Move fw interface definitions to a header (v2)
p2sb:
- Fix UAF when caller uses resource name
platform/mellanox:
- mlxreg-lc: Make error handling flow consistent
- Remove redundant 'NULL' check
- Remove unnecessary code
- mlxreg-lc: Fix locking issue
- mlxreg-lc: Fix coverity warning
platform/surface:
- Split memcpy() of struct ssam_event flexible array
- aggregator_registry: Add HID devices for sensors and UCSI client to SP8
- aggregator_registry: Rename HID device nodes based on new findings
- aggregator_registry: Rename HID device nodes based on their function
- aggregator_registry: Add support for Surface Laptop Go 2
platform/x86:
- use PLATFORM_DEVID_NONE instead of -1
platform/x86/amd:
- pmc: Dump idle mask during "check" stage instead
- pmc: remove CONFIG_DEBUG_FS checks
- pmc: Fix build without debugfs
- pmc: Add sysfs files for SMU
- pmc: Add an extra STB message for checking s2idle entry
- pmc: Always write to the STB
- pmc: Add defines for STB events
platform/x86/amd/pmf:
- Remove unused power_delta instances
- install notify handler after acpi init
- Add sysfs to toggle CnQF
- Add support for CnQF
- Fix clang unused variable warning
- Fix undefined reference to platform_profile
- Force load driver on older supported platforms
- Handle AMT and CQL events for Auto mode
- Add support for Auto mode feature
- Get performance metrics from PMFW
- Add fan control support
- Add heartbeat signal support
- Add debugfs information
- Add support SPS PMF feature
- Add support for PMF APCI layer
- Add support for PMF core layer
- Add ABI doc for AMD PMF
- Add AMD PMF driver entry
platform/x86/intel/wmi:
- thunderbolt: Use dev_groups callback
pmc_atom:
- Amend comment style and grammar
- Make terminator entry uniform
- Improve quirk message to be less cryptic
- Fix SLP_TYPx bitfield mask
samsung-laptop:
- Move acpi_backlight=[vendor|native] quirks to ACPI video_detect.c
simatic-ipc:
- add new model 427G
- enable watchdog for 227G
thinkpad_acpi:
- Explicitly set to balanced mode on startup
tools/power/x86/intel-speed-select:
- Release v1.13
- Optimize CPU initialization
- Utilize cpu_map to get physical id
- Remove unused struct clos_config fields
- Enforce isst_id value
- Do not export get_physical_id
- Introduce is_cpu_in_power_domain helper
- Cleanup get_physical_id usage
- Convert more function to use isst_id
- Add pkg and die in isst_id
- Introduce struct isst_id
- Remove unused core_mask array
- Remove dead code
- Fix cpu count for TDP level display
toshiba_acpi:
- change turn_on_panel_on_resume to static
- Remove duplicate include
- Set correct parent for input device.
- Add fan RPM reading (hwmon interface)
- Add fan RPM reading (internals)
- Stop using acpi_video_set_dmi_backlight_type()
- Fix ECO LED control on Toshiba Z830
- Battery charge mode in toshiba_acpi (internals)
- Battery charge mode in toshiba_acpi (sysfs)
wmi:
- Drop forward declaration of static functions
- Allow duplicate GUIDs for drivers that use struct wmi_driver
x86-android-tablets:
- Fix broken touchscreen on Chuwi Hi8 with Windows BIOS
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmM9eLgUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zIzAf+JG058wucK0Zsnu4POzGp+uHjnWuu
AJUmTeRvCD7MidwIv5PiwEtTucQ8OuXYR+tPc8LIwCVZtc05FBmh7Y8le/CX0SS6
n9EZIvCk3Owosti5w2TPnCK920kh+Wfxl/fmfDbpi6+lpAL8r+F/mZEGKGFdZpWu
Q+yM/eyxwPH8q8gjrXOUC7rN43aYeO3OCpNG3GYkQ/2S5qrjuz39dXhNVzdSsxm7
aYOqJRNjZQEjQ3kJcp65kC6oWp3UaI1zdpGwhBG/SY8BCtCYZzlRy7gN2FCJfAa/
EyYayOvdy0zNwewbIYzck4W80hUDtfidgZgZ9crQscO/JjbGi6LhveD4YA==
=afGw
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- AMD Platform Management Framework (PMF) driver with AMT and QnQF
support
- AMD PMC: Improved logging for debugging s2idle issues
- Big refactor of the ACPI/x86 backlight handling, ensuring that we
only register 1 /sys/class/backlight device per LCD panel
- Microsoft Surface:
- Surface Laptop Go 2 support
- Surface Pro 8 HID sensor support
- Asus WMI:
- Lots of cleanups
- Support for TUF RGB keyboard backlight control
- Add support for ROG X13 tablet mode
- Siemens Simatic: IPC227G and IPC427G support
- Toshiba ACPI laptop driver: Fan hwmon and battery ECO mode support
- tools/power/x86/intel-speed-select: Various improvements
- Various cleanups
- Various small bugfixes
* tag 'platform-drivers-x86-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (153 commits)
platform/x86: use PLATFORM_DEVID_NONE instead of -1
platform/x86/amd: pmc: Dump idle mask during "check" stage instead
platform/x86/intel/wmi: thunderbolt: Use dev_groups callback
platform/x86/amd: pmc: remove CONFIG_DEBUG_FS checks
platform/surface: Split memcpy() of struct ssam_event flexible array
platform/x86: compal-laptop: Get rid of a few forward declarations
platform/x86: intel-uncore-freq: Use sysfs_emit() to instead of scnprintf()
platform/x86: dell-smbios-base: Use sysfs_emit()
platform/x86/amd/pmf: Remove unused power_delta instances
platform/x86/amd/pmf: install notify handler after acpi init
Documentation/ABI/testing/sysfs-amd-pmf: Add ABI doc for AMD PMF
platform/x86/amd/pmf: Add sysfs to toggle CnQF
platform/x86/amd/pmf: Add support for CnQF
platform/x86/amd: pmc: Fix build without debugfs
platform/x86: hp-wmi: Support touchpad on/off
platform/x86: int3472/discrete: Drop a forward declaration
platform/x86: toshiba_acpi: change turn_on_panel_on_resume to static
platform/x86: wmi: Drop forward declaration of static functions
platform/x86: toshiba_acpi: Remove duplicate include
platform/x86: msi-laptop: Change DMI match / alias strings to fix module autoloading
...
I'm getting warnings:
/tmp/next/build/drivers/leds/leds-pca963x.c: In function 'pca963x_register_leds':
/tmp/next/build/drivers/leds/leds-pca963x.c:355:3: error: this 'if' clause does not guard...
+[-Werror=misleading-indentation]
355 | if (hw_blink)
| ^~
/tmp/next/build/drivers/leds/leds-pca963x.c:357:4: note: ...this statement, but the latter is
+misleadingly indented as if it were guarded by the 'if'
357 | led->blinking = false;
| ^~~
cc1: all warnings being treated as errors
Fix the indentation to make them go away.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
LEDs would behave differently depending on the blink hardware
acceleration configuration. This commit will make LEDs respond exactly
the same independently of the hardware acceleration status.
In other words, if you had two pca963x, side by side, one with blink
hardware acceleration "ON" and the other "OFF; and performed some
arbitrary sequence of API calls (e.g. turn on/off, change brightness,
change blink mode, etc.) you probably would end with not matching LED
states.
'pca963x software blink' and 'leds-gpio' behavior were used as
reference.
Actual chip used to validate this change: pca9634
Some of the unmatched behaviors being fixed are (when hw blink was "ON")
- Leds would stop blinking when the brightness was changed.
- Leds would persist their blinking mode even after being
turned off (brightness = 0).
- Leds would only blink if another led was solid (pca963x will be
forced out of low power)
Signed-off-by: Bernardo Rodrigues <bernardocrodrigues@live.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
This adds support of the Siemens Simatic IPC227G. Its LEDs are connected
to GPIO pins provided by the gpio-f7188x module. We make sure that
gets loaded, if not enabled in the kernel config no LED support will be
available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20220825104422.14156-6-henning.schild@siemens.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The mutex might still be in use until the devm cleanup callback
devm_led_classdev_flash_release() is called. This only happens some time
after lm3601x_remove() completed.
Fixes: e63a744871 ("leds: lm3601x: Convert class registration to device managed")
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Returning an error value from an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As lm3697_remove() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, don't pass the error value up the stack. Instead continue
to clean up and return 0.
This patch is a preparation for making i2c remove callbacks return void.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
fixups for multicolor. Clevo-mail driver got disabled, it needs API
fix.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYvEUpgAKCRAw5/Bqldv6
8vDGAKCYdETEgfPsExMizqACzkcQWYzpUgCfetiY56Wkr1vLx+kCBvHS9m6wC+8=
=MT+Z
-----END PGP SIGNATURE-----
Merge tag 'leds-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"A new driver for bcm63138, is31fl319x updates, fixups for multicolor.
The clevo-mail driver got disabled, it needs an API fix"
* tag 'leds-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (23 commits)
leds: is31fl319x: use simple i2c probe function
leds: is31fl319x: Fix devm vs. non-devm ordering
leds: is31fl319x: Make use of dev_err_probe()
leds: is31fl319x: Make use of device properties
leds: is31fl319x: Cleanup formatting and dev_dbg calls
leds: is31fl319x: Add support for is31fl319{0,1,3} chips
leds: is31fl319x: Move chipset-specific values in chipdef struct
leds: is31fl319x: Use non-wildcard names for vars, structs and defines
leds: is31fl319x: Add missing si-en compatibles
dt-bindings: leds: pwm-multicolor: document max-brigthness
leds: turris-omnia: convert to use dev_groups
leds: leds-bcm63138: get rid of LED_OFF
leds: add help info about BCM63138 module name
dt-bindings: leds: leds-bcm63138: unify full stops in descriptions
dt-bindings: leds: lp50xx: fix LED children names
dt-bindings: leds: class-multicolor: reference class directly in multi-led node
leds: bcm63138: add support for BCM63138 controller
dt-bindings: leds: add Broadcom's BCM63138 controller
leds: clevo-mail: Mark as broken pending interface fix
leds: pwm-multicolor: Support active-low LEDs
...
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
When non-devm resources are allocated they mustn't be followed by
devm allocations, otherwise it will break the tear down ordering
and might lead to crashes or other bugs during ->remove() stage.
Fix this by wrapping mutex_destroy() call with
devm_add_action_or_reset().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Simplify the error handling in probe function by switching from
dev_err() to dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Fix remaining non-standard place for comments.
Remove remaining dev_dbg after regmap_read in is31fl3196_brightness_set.
Remove __func__ in dev_dbg calls, instead adding "channel" string to
describe the first displayed value.
Change remaining container_of() call to be on one line,
as well as a few others.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Allow setting chips' specifics in chipdef struct by adding fields for:
- the reset register address
- a pointer to a regmap_config struct
- a pointer to a brightness_set function
- current default, min and max values
- a boolean to distinguish 319{0,1,3} and 319{6,9} chips
and use those fields in places where distinction has to be made.
The fields for 319{0,1,3} still point to 319{6,9} values.
No functional change.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The driver core supports the ability to handle the creation and removal
of device-specific sysfs files in a race-free manner. Take advantage of
that by converting this driver to use this by moving the sysfs
attributes into a group and assigning the dev_groups pointer to it.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux-leds@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The whole "enum led_brightness" is marked as obsolete. Replace it with a
(non-)zero check.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
It's what we do for all other LEDs drivers.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
It's a new controller first introduced in BCM63138 SoC. Later it was
also used in BCM4908, some BCM68xx and some BCM63xxx SoCs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add support for LEDs wired up to light when the PWM output is low, just
like the regular PWM LEDs.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
When requesting a PWM it might return -EPROBE_DEFER if it hasn't probed
yet. This is not an error, so just propagate the -EPROBE_DEFER without
logging anything. There is already dev_err_probe for exactly this
situation.
Fixes: 9fa2762110 ("leds: Add PWM multicolor driver")
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
On Apollo Lake the pinctrl drivers will now come up without ACPI. Use
that instead of open coding it.
Create a new driver for that which can later be filled with more GPIO
based models, and which has different dependencies.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee@kernel.org>
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
The leds-trigger-pattern documentation describes how the brightness of
the LED should transition linearly from one brightness value to the
next, over the given delta_t.
But the pattern engine in the Qualcomm LPG hardware only supports
holding the brightness for each entry for the period.
This subset of patterns can be represented in the leds-trigger-pattern
by injecting zero-time transitions after each entry in the pattern,
resulting in a pattern that pattern that can be rendered by the LPG.
Rework LPG pattern interface to require these zero-time transitions, to
make it comply with this subset of patterns and reject the patterns it
can't render.
Fixes: 24e2d05d1b ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Returning an error value from an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As stk3310_set_state() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, don't pass the error value up the stack. Instead continue
to clean up and return 0.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Qualcomm LPG driver fails to probe unless PWM support is enabled so
add the missing Kconfig dependency.
Fixes: 24e2d05d1b ("leds: Add driver for Qualcomm LPG")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Make the AUX pin optional, since it isn't a core part of functionality,
and the device is designed to be operational with only one CTRL pin.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Use dev_err_probe instead of dev_err to avoid duplicate error
messages if the GPIO allocation makes the probe defer.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't make
a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more helpful
message if a problem occurs and return 0 to suppress the generic message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The drivers/leds/rgb subdirectory is relatively fresh, so we move this
new PWM multi-color driver into it.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
By allowing to group multiple monochrome PWM LEDs into multicolor LEDs,
all involved LEDs can be controlled in-sync. This enables using effects
using triggers, etc.
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The regulator LED can easily be adapted to probe from the
device tree.
We switch led_classdev_register() to led_classdev_register_ext()
passing some struct led_init_data init_data that we leave NULL
save the fwnode if platform data isn't present so that it will be
populated from the device tree.
If we have platform data we set up the name from the platform
data but using init_data instead.
Cc: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Instead of repeating the hard to read &pdev->dev just create a
local struct device *dev in probe().
Cc: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Up to now pca9532_destroy_devices() returns always zero because it's
always called with data != NULL. Remove the never-taken error path and
make it return void which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add pm8350c compatible and lpg_data to the driver.
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
with their output being routed to various other components, such as
current sinks or GPIOs.
Each LPG instance can operate on fixed parameters or based on a shared
lookup-table, altering the duty cycle over time. This provides the means
for hardware assisted transitions of LED brightness.
A typical use case for the fixed parameter mode is to drive a PWM
backlight control signal, the driver therefor allows each LPG instance
to be exposed to the kernel either through the LED framework or the PWM
framework.
A typical use case for the LED configuration is to drive RGB LEDs in
smartphones etc, for which the driver supports multiple channels to be
ganged up to a MULTICOLOR LED. In this configuration the pattern
generators will be synchronized, to allow for multi-color patterns.
The idea of modelling this as a LED driver ontop of a PWM driver was
considered, but setting the properties related to patterns does not fit
in the PWM API. Similarly the idea of just duplicating the lower bits in
a PWM and LED driver separately was considered, but this would not allow
the PWM channels and LEDs to be configured on a per-board basis. The
driver implements the more complex LED interface, and provides a PWM
interface on the side of that, in the same driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[On the Sony Xperia Nile Discovery, SDM630]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The mach/hardware.h is included in lots of places, and it provides
three different things on pxa:
- the cpu_is_pxa* macros
- an indirect inclusion of mach/addr-map.h
- the __REG() and io_pv2() helper macros
Split it up into separate <linux/soc/pxa/cpu.h> and mach/pxa-regs.h
headers, then change all the files that use mach/hardware.h to
include the exact set of those three headers that they actually
need, allowing for further more targeted cleanup.
linux/soc/pxa/cpu.h can remain permanently exported and is now in
a global location along with similar headers. pxa-regs.h and
addr-map.h are only used in a very small number of drivers now
and can be moved to arch/arm/mach-pxa/ directly when those drivers
are to pass the necessary data as resources.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-leds@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
that need review and did not make it.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCYj+mOQAKCRAw5/Bqldv6
8pXqAJ9co9nkfU7H+VIdk4FWHp6w87fDCACeKRIOcG5eK50yoBhMGclvuuC7V5s=
=gSle
-----END PGP SIGNATURE-----
Merge tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Nothing major here, there are two drivers that need review and did not
make it into this round"
* tag 'leds-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: pca955x: Allow zero LEDs to be specified
leds: pca955x: Make the gpiochip always expose all pins
leds: simatic-ipc-leds: Don't directly deref ioremap_resource() returned ptr
leds: simatic-ipc-leds: Make simatic_ipc_led_mem_res static
leds: lm3692x: Return 0 from remove callback
leds: sgm3140: Add ocs,ocp8110 compatible
dt-bindings: vendor-prefixes: Add ocs prefix
dt-bindings: leds: common: fix unit address in max77693 example
It's valid to use the PCA955x devices just for GPIOs and not for LEDs.
In this case, as PCA955X_TYPE_GPIO is now equivalent to
PCA955X_TYPE_NONE, remove the test for whether we have any child nodes
specified in the devicetree.
A consequence of this is it's now possible to bind the driver to a
PCA955x device when dynamically instantiated through the I2C subsystem's
`new_device` interface.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The devicetree binding allows specifying which pins are GPIO vs LED.
Limiting the instantiated gpiochip to just these pins as the driver
currently does requires an arbitrary mapping between pins and GPIOs, but
such a mapping is not implemented by the driver. As a result,
specifying GPIOs in such a way that they don't map 1-to-1 to pin indexes
does not function as expected.
Establishing such a mapping is more complex than not and even if we did,
doing so leads to a slightly hairy userspace experience as the behaviour
of the PCA955x gpiochip would depend on how the pins are assigned in the
devicetree. Instead, always expose all pins via the gpiochip to provide
a stable interface and track which pins are in use.
Specifying a pin as `type = <PCA955X_TYPE_GPIO>;` in the devicetree
becomes a no-op.
I've assessed the impact of this change by looking through all of the
affected devicetrees as of the tag leds-5.15-rc1:
```
$ git grep -l 'pca955[0123]' $(find . -name dts -type d)
arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
```
These are all IBM-associated platforms. I've analysed both the
devicetrees and schematics where necessary to determine whether any
systems hit the hazard of the current broken behaviour. For the most
part, the systems specify the pins as either all LEDs or all GPIOs, or
at least do so in a way such that the broken behaviour isn't exposed.
The main counter-point to this observation is the Everest system whose
devicetree describes a large number of PCA955x devices and in some cases
has pin assignments that hit the hazard. However, there does not seem to
be any use of the affected GPIOs in the userspace associated with
Everest.
Regardless, any use of the hazardous GPIOs in Everest is already broken,
so let's fix the interface and then fix any already broken userspace
with it.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Sparse (rightly) currently gives the following warning:
drivers/leds/simple/simatic-ipc-leds.c:155:40:
sparse: sparse: incorrect type in assignment (different address spaces)
expected void *static [toplevel] simatic_ipc_led_memory
got void [noderef] __iomem *
Fix this by changing the type of simatic_ipc_led_memory to void __iomem *
and use readl()/writel() to access it.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Gerd Haeussler <gerd.haeussler.ext@siemens.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
simatic_ipc_led_mem_res is not used outside of the driver, make it static.
Cc: Henning Schild <henning.schild@siemens.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The only difference between returning zero or a non-zero value is that
for the non-zero case the i2c will print a generic error message
("remove failed (-ESOMETHING), will be ignored").
In this case however the driver itself already emitted a more helpful
error message, so the additional error message isn't helpful at all.
The long-term goal is to make the i2c remove callback return void, making
all implementations return 0 is preparatory work for this change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
