Even if the CONFIG_PM explicity is undefined, let's convert to the
modern PM ops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
BUG() used in the driver is just to spit the stack trace on buggy
points, not really needed to stop the whole operation. For that
purpose, it'd be more convenient to use snd_BUG() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code sequence is unsafe in modules:
static u64 mask = DMA_BIT_MASK(something);
...
if (!dev->dma_mask)
dev->dma_mask = &mask;
as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses. Moreover, they
all follow this with:
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = mask;
where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.
Fix these issues by using the new dma_coerce_coherent_and_mask()
function.
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA25x also shows some problems when using interrupts during reset
handling. Thus do not use interrupts on all pxa kinds (to detect codec
ready state). Instead use a common mdelay-loop on all platforms to
detect codecs becoming ready.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_dmaengine_dai_dma_data for passing the dma parameters from
clients to the pxa pcm lib. This does no functional change, it's just an
intermedia step to migrate the pxa bits over to dmaengine.
The calculation of dcmd is a transition hack which will be removed again
in a later patch. It's just there to make the transition more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does nothing functionally, it just gives the function a new name and
modifies the prototype slightly in order to clarify what the function is doing
(which is not necessarily asserting the reset).
Some commentary also added.
Tested on a palm treo 680 machine.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes some code that implements a work-around to a hardware bug in
the ac97 controller on the pxa27x. A bug in the controller's warm reset
functionality requires that the mfp used by the controller as the AC97_nRESET
line be temporarily reconfigured as a generic output gpio (AF0) and manually
held high for the duration of the warm reset cycle. This is what was done in
the original code, but it was broken long ago by commit fb1bf8cd
([ARM] pxa: introduce processor specific pxa27x_assert_ac97reset())
which changed the mfp to a GPIO input instead of a high output.
The fix requires the ac97 controller to obtain the gpio via gpio_request_one(),
with arguments that configure the gpio as an output initially driven high.
Tested on a palm treo 680 machine. Reportedly, this broken code only prevents a
warm reset on hardware that lacks a pull-up on the line, which appears to be the
case for me.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Cold reset on the pxa27x currently fails and
pxa2xx_ac97_try_cold_reset: cold reset timeout (GSR=0x44)
appears in the kernel log. Through trial-and-error (the pxa270 developer's
manual is mostly incoherent on the topic of ac97 reset), I got cold reset to
complete by setting the WARM_RST bit in the GCR register (and later noticed that
pxa3xx does this for cold reset as well). Also, a timeout loop is needed to
wait for the reset to complete.
Tested on a palm treo 680 machine.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_PM is set but CONFIG_PM_SLEEP is unset,
SIMPLE_DEV_PM_OPS() ignores the given functions, and this leads to
compile warnings.
For avoiding this, simply check CONFIG_PM_SLEEP instead of CONFIG_PM.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rob Herring has done a sweeping change cleaning up all of the mach/io.h includes,
moving some of the oft-repeated macros to a common location and removing a bunch of
boiler plate. This is another step closer to a common zImage for multiple platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YIsn
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
pxa was missed in the moving of IOMEM to a common definition, so lots of
IOMEM redefined warnings were introduced. So remove pxa IOMEM definition
and fix all the fallout.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: rtc-linux@googlegroups.com
Cc: alsa-devel@alsa-project.org
For simple modules that contain a single amba_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_amba_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
This patch converts the drivers in sound/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pxa2xx_pcm_hw_free frees dma channel and sets prtd->dma_ch to -1,
but does not set prtd->params to NULL, so if pxa2xx_pcm_hw_params will
be called immediately, it leaves prtd->dma_ch initialized with -1,
and it results in oops in __pxa2xx_pcm_prepare. This bug is triggered
via SDL.
This patch adds check for prtd->dma_ch to __pxa2xx_pcm_prepare and
cleans prtd->params, so now it works properly.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AACI TRM requires the MAINCR enable bit to be held zero for two
bitclk cycles plus three apb_pclk cycles. Use a delay of 1us to
ensure this.
Ensure that writes to MAINCR to change the addressed codec only happen
when required, and that they take effect in a similar manner to the
above, otherwise we seem to occasionally have stuck slot busy bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no need to call snd_pcm_period_elapsed() each time a period
elapses - we can call it after we're done once loading/unloading the
FIFO with data. ALSA works out how many periods have elapsed by
reading the current pointers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the AACI announcement printk say which primecell part number
has been found. Display the revision as an unsigned decimal, and
display only the first 8 hex digits of the base address unless it's
larger.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When double-rate mode was selected, we weren't setting the additional
two channel mask bits to allow double-rate to work. Rearrange the
hw_params code to allow the correct channel mask to be selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AC'97 codecs only support two channels for recording, so we shouldn't
advertize that there are up to six channels available. Limit the
selection of 4 and 6 channel audio to playback only.
As this adds additional SNDRV_PCM_STREAM_PLAYBACK conditionals, we can
combine some resulting in the elimination of __aaci_pcm_open() entirely,
and making the code easier to read.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claiming the IRQ each time a playback or capture interface is opened
is wasteful; the second copy of the registered handler is identical to
the first and just wastes resources. Track the number of opens and
only register the handler when necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Relying on the access time of peripherals is unreliable - it depends
on the speed of the CPU and the bus. On Versatile Express, these
timeouts were expiring, causing the driver to fail.
Add udelay(1) to ensure that they don't expire early, and adjust
timeouts to give a reasonable margin over the response times.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that a timeout coincident with the condition being waited for
results in success rather than failure. This helps avoid timeout
conditions being inappropriately flagged.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The commit 29a4f2d3 used writel() at offset 0x26 which is
half-word aligned causing unaligned exceptions on a
Cortex-A8. The original patch solved the "aaci-pl041 fpga:04:
ac97 read back fail" issue on a soft reset. Reading from any
arbitrary aaci register seems to solve this issue.
Signed-off-by: Philby John <pjohn@mvista.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is
already freed") when a device was opened but the hw_params() call
failed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now most (if not all) PXA platforms have been switched to the new MFP
API, it's rather safe to remove these unnecessary pxa_gpio_mode() calls
in pxa2xx-ac97-lib.c now.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MFP registers are saved and restored by the mfp sys_device before all
other platform devices, and it is unnecessary here.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We can use finer-grained locking, which makes things easier when
we gain DMA support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recording and playback paths are now the same, eliminate
the needless conditionals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's no need for a specific rule; ALSA's generic AC'97 support
calculates the necessary rate constraint information itself, and
we can use this directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd_ac97_pcm_open() is called with the exactly same arguments
for both playback and capture directions. Remove the unneeded check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
pcm->r[1].slots is the double rate slot information, not the
capture information. For capture, 'pcm' will already be the
capture ac97 pcm structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the buffer size calculation to use the size which ALSA is expecting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After a reboot on an ARM1176 which amounts to a softreset, it has been
noted that the ALSA driver does not get registered and the probe fails
with the error "aaci-pl041 fpga:04: ac97 read back fail". In the process
of reading from a register the SL1TxBusy bit is set indicating that the
transceiver is busy and remains so until the default timeout occurs.
Set the Power down register 0x26 to an arbitrary value as specified in
the PL041 manual (page: 3-18) so that AACISL1TX/AACISL2TX registers take
their default state.
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Today's linux-next fails to build with
sound/arm/pxa2xx-ac97.c: In function 'pxa2xx_ac97_probe':
sound/arm/pxa2xx-ac97.c:211: error: 'pxa2xx_audio_ops_t' has no member named 'codec_data'
make[2]: *** [sound/arm/pxa2xx-ac97.o] Error 1
It looks like commit e2365bf313 has
introduced this; patch below.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Used for applications such as direct bluetooth connections on
smartphones which don't go via the CPU. This used to be supported
before the refactoring to share code but this check was removed
during that move.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for passing platform data to ac97 bus devices
from PXA2xx-AC97 driver..
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check for rtd->params->drcmr != NULL before accessing it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently there are two possible platform datas for the PXA AC97 driver:
one supported by the generic AC97 driver only which provides callbacks
to allow board-specific configuration at stream startup and teardown,
and another for pxa2xx-ac97-lib which allows configuration of the reset
GPIO for PXA2xx CPUs.
Obviously this won't actually work when using the generic AC97 driver
since the drivers will attempt to parse the platform data in both
formats. Fix this by merging the two structures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
the variable gsr_bit is set in isr. It is however set to 0 and interrupts are
disabled prior to reset. Hence it doesn't make a lot of sense to show the
content of gsr_bit in case of a reset timeout.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It depends on L3 support from 2.4 kernel (CONFIG_L3) that never got
merged into mainline. Since there's no way to use it on any of
supported machines (iPaq h3100 or h3600), better drop it for now.
It can be reimplemented later using ASoC infrastructure (there's
already a driver for uda1341 codec in mainline, so only CPU and machine
parts need to be written).
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the PXA27x series allow 2 gpios to reset the ac97 bus,
allow through platform data configuration the definition of
the correct gpio which will reset the AC97 bus.
This comes from a silicon defect on the PXA27x series, where
the gpio must be manually controlled in warm reset cases.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa-regs.h and hardware.h are not intended for use directly in driver
code, remove those unnecessary references.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If AC97 unit is in partially enabled state, early request_irq can trigger
IRQ storm or even full hang up. Workaround this by forcibly switching ACLINK off
at the start of the probe.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The rest of the code relies on the runtime data being zero initialised
so we need to use kzalloc() to allocate it.
Reported-by: Oliver Ford <ipaqlinux@oliford.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai