On some platform it may happen that the input clock to keyboard may
change during suspend, thus impacting its wakeup capability.
There is no means for keyboard driver to know this frequency before
hand. Hence introduce a platform data 'suspended_rate' which indicates
the frequency during suspend at which keyboard operates.
Accordingly reprogram keyboard while going into suspend and restore
original configuration at the time of resume.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
SPEAr keyboard should normally disable clock during suspend and enable it
during resume.
For cases where it is expected to act as a wakeup source the clock can
remain in the same state i.e. kept enabled if it is being used.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Current implementation hard coded keyboard frequency configuration
assuming input clock as fixed APB (83 MHz). Generalize the configuration
using clock framework APIs.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All SPEAr keyboard registers are 32 bit wide and are word aligned. This
patch aligns all io access to be word size using relaxed version of
readl/writel.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch is to disable device wakeup while removing keyboard.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the new i.mx clock framework we should pass NULL as the keypad
clock name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adapt clock handling to the new i.mx clock framework and fix the following
warning:
input: imx-keypad as /devices/platform/imx-keypad/input/input0
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:511 __clk_enable+0x98/0xa8()
Modules linked in:
[<c001a680>] (unwind_backtrace+0x0/0xf4) from [<c002452c>] (warn_slowpath_commo)
[<c002452c>] (warn_slowpath_common+0x48/0x60) from [<c0024560>] (warn_slowpath_)
[<c0024560>] (warn_slowpath_null+0x1c/0x24) from [<c02c4ec4>] (__clk_enable+0x9)
[<c02c4ec4>] (__clk_enable+0x98/0xa8) from [<c02c4ef8>] (clk_enable+0x24/0x5c)
[<c02c4ef8>] (clk_enable+0x24/0x5c) from [<c027ac6c>] (imx_keypad_open+0x28/0xc)
[<c027ac6c>] (imx_keypad_open+0x28/0xc8) from [<c0274b14>] (input_open_device+0)
[<c0274b14>] (input_open_device+0x78/0xa8) from [<c01ec884>] (kbd_connect+0x60/)
[<c01ec884>] (kbd_connect+0x60/0x80) from [<c0273b94>] (input_attach_handler+0x)
[<c0273b94>] (input_attach_handler+0x220/0x258) from [<c02755d4>] (input_regist)
[<c02755d4>] (input_register_device+0x31c/0x390) from [<c038da1c>] (imx_keypad_)
[<c038da1c>] (imx_keypad_probe+0x2e4/0x3b8) from [<c020326c>] (platform_drv_pro)
[<c020326c>] (platform_drv_probe+0x18/0x1c) from [<c0201f64>] (driver_probe_dev)
[<c0201f64>] (driver_probe_device+0x84/0x210) from [<c020217c>] (__driver_attac)
[<c020217c>] (__driver_attach+0x8c/0x90) from [<c02008f8>] (bus_for_each_dev+0x)
[<c02008f8>] (bus_for_each_dev+0x68/0x90) from [<c0201064>] (bus_add_driver+0xa)
[<c0201064>] (bus_add_driver+0xa4/0x23c) from [<c020275c>] (driver_register+0x7)
[<c020275c>] (driver_register+0x78/0x12c) from [<c00087c0>] (do_one_initcall+0x)
[<c00087c0>] (do_one_initcall+0x34/0x188) from [<c04b9310>] (kernel_init+0xe4/0)
[<c04b9310>] (kernel_init+0xe4/0x1a8) from [<c0015bd8>] (kernel_thread_exit+0x0)
---[ end trace 1d550e891d03d7ce ]---
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Two fixes for regressions in Wacom driver and fixes for drivers using
threaded IRQ framework without specifying IRQF_ONESHOT."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: request threaded-only IRQs with IRQF_ONESHOT
Input: wacom - don't retrieve touch_max when it is predefined
Input: wacom - fix retrieving touch_max bug
Input: fix input.h kernel-doc warning
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail. This patch adds the
IRQF_ONESHOT to input drivers where it is missing. Not modified by
this patch are those drivers where the requested IRQ will always be a
nested IRQ (e.g. because it's part of an MFD), since for this special
case IRQF_ONESHOT is not required to be specified when requesting the
IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix harmless reference off end of array
Reported-by: <dcb314@hotmail.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?43861
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The keypad could cause multiple interrupts to be fired in succession
since we weren't waiting for the IRQs to clear properly in the
interrupt handler. We wait for a number of bus iterations (the
readl():s from the peripheral bus will stall, so these are quite
long) before giving up on getting keys ready to read, then we
sleep until the IRQ is deasserted (this is OK since the interrupt
is threaded). Also use the debounce platform data for another
hardcoded wait loop.
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Reviewed-by: Rikard Olsson <rikard.p.olsson@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added the multi key press support for SKE keypad by modifying the irq
function for handling the two different keys on the same column and also
pressing the two different keys of different columns on the same ASR
register.
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
pdata is zeroed using memset just a few lines before, so there is no
need to set the nbuttons member to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
When platform keymap is not supplied to matrix_keypad_build_keymap()
and device tree support is enabled, try locating specified property
and load keymap from it. If property name is not defined, try using
"linux,keymap".
Based on earlier patch by Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change matrix-keymap helper to be out-of-line, like sparse keymap,
allow the helper perform basic keymap validation and return errors,
and prepare for device tree support.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Direct keys usage may not start from KP_DKIN0, add a msk option
to configure the specifics for platforms that can skip some keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
KPDK_DK only indicates the pin level of direct key.
So it is related to board, and low level may be active which
indicates that a key is pressed.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When direcct_key_num is 0, the mask should be 0.
When direcct_key_num is 1, the mask should be 0b1.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
When the keypad is used as wake up source, the clock can not
be disabled. Or it can not detect key pressing.
If the keypad is used as wake up source, when resume back,
do not enable the clock and configure it again because the
register content is retained.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
I believe that "trying to access hardware" is more correct English
than "trying access hardware".
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
settle_time and debounce_period are u8 and thus can not be greater than
TC3589x_MAX_DEBOUNCE_SETTLE which is 255.
There also no need to mask out nibbles form board->krow and board->kcol
as we validate that they are in correct range.
Reported-by: Werner <w.landgraf@ru.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of allocating and managing keymap separately from the keypad
structure stick it at the end as a variable-length array.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SIMPLE_DEV_PM_OPS already defines constant dev_pm_ops.
Also guard PM methods with CONFIG_PM_SLEEP and get rid of some
unneeded #ifdefs.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also use CONFIG_PM_SLEEP instead of CONFIG_PM to guard PM methods.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts the drivers in drivers/input/* to use
module_serio_driver() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for the keypad part of the LM8333 and is
prepared for possible GPIO/PWM drivers. Note that this is not a MFD
because you cannot disable the keypad functionality which, thus,
has to be handled by the core anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
Following commit broke DT support for tegra-kbc by removing pdata
allocation completely:
commit 023cea0ecf
Author: Shridhar Rasal <srasal@nvidia.com>
Date: Fri Feb 3 00:27:30 2012 -0800
Input: tegra-kbc - allow skipping setting up some of GPIO pins
This patch restores it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for sa11x0 sparse irq conversion, explicitly include
mach/irqs.h as it will not be included for sparse irq.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some of buttons, like power-on key or onkey, may only generate interrupts
when pressed and not actually be mapped as gpio in the system. Allow
setting gpio to invalid value and specify IRQ instead to support such
keys. The debounce timer is used not to debounce but to ignore new IRQs
coming while button is kept pressed.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
request_any_context_irq() should handle the case when using GPIO expanders
that themselves use threaded IRQs, and so the premise of change
7e2ecdf438 is incorrect.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts the drivers in drivers/input/* to use the
module_i2c_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch allows us to drop the OMAP dependency from the OMAP4 keypad
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is an incremental patch updating to the revised bindings for
matrix keyboards.
This includes an optional "linux,fn-keymap" binding that is not yet
implemented, that will be used to specify the Fn-key modifier layout
if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds a simple device tree binding for simple key matrix data and
a helper to fill in the platform data.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Thaw and poweroff routines are missing for spear-keyboard. They are
required for:
- Error case scenarios during freeze
- Using test features, of hibernate.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let platform pass mode information to keyboard driver according to which
it configures itself. The mode can be
- KEYPAD_9x9 0
- KEYPAD_6x6 1
- KEYPAD_2x2 2
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow marking some of GPIO pins as ignored to to avoid continuously
generating KBC input events.
Signed-off-by: Shridhar Rasal <srasal@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable keypress interrupt to support wakeup from low power state.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We don't actually care if the device has been runtime suspended immediately
so we can just drop the reference without waiting for any state change to
be implemented. This may allow us to avoid some suspend/resume cycles and
is a bit more friendly to the rest of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also proper guard for system suspend/resume methods is CONFIG_PM_SLEEP,
not CONFIG_PM.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Because we are using platform_device_probe() to register the driver
we do not need to assign driver's probe method. We also can mark
ske_keypad_probe(), together with ske_keypad_chip_init(), as __init
instead of __devinit.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: bcm5974 - set BUTTONPAD property
Input: serio_raw - return proper result when serio_raw_write fails
Input: serio_raw - really signal HUP upon disconnect
Input: serio_raw - remove stray semicolon
Input: revert some over-zealous conversions to module_platform_driver()
Recent conversion to module_platform_driver() went a bit too far and
converted not only drivers that used platform_driver_register() but
also ones using platform_driver_probe(), breaking them in process.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 940ab88962 introduced a new macro to
save some platform_driver boilerplate code. Use it.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is nothing in keypad platform definitions that requires
the driver be complied on Samsung platform only, so let's move them
out of the platform subdirectory and relax the dependencies.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in input dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver has been tested with hardware and works as expected. To use
it add the platform data as appropriate and register it with the
corresponding I2C bus.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
The ADP5585 family keypad decoder and IO expander is similar to the ADP5589,
however it features less IO pins, and lacks hardware assisted key-lock
functionality. Unfortunately the register addresses are different, as well as
the event codes and bit organization within the port related registers.
Move ADP5589 Register defines from the header file into the main source file.
Add new defines while making sure we don't break existing platform_data.
Add register address translation, and turn device specific defines into variables.
Introduce some helper functions and disable functions that doesn't
exist on the added devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The imx_keypad driver was indicating that it was wakeup capable in
imx_keypad_probe(), but it didn't implement suspend or resume methods.
According to the i.MX series MCU Reference Manual, the kpp (keypad
port) is a major wake up source which can detect any key press even
in low power mode and even when there is no clock.
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use the of_property_read_u32() helper function to retrieve u32 values
from the device tree. Also do not pass the len parameter to
of_get_property if it isn't checked afterwards.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Take spinlock when entering ISR and timer routine to ensure that we do not
race while enabling/disabling FIFO interrupts.
Also we do not need to take teh spinlock in tegra_kbc_startremove() since
interrupt is completely disabled.
Tested-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For wakeup to be reliable, kbc needs to be in interrupt mode before suspend.
Created common routine to control the FIFO interrupt.
Added synchronization to ensure orderly suspend.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
WARNING: drivers/input/keyboard/built-in.o(.text+0xb55b): Section mismatch in reference from the function tc3589x_keypad_open() to the function .devinit.text:tc3589x_keypad_init_key_hardware()
The function tc3589x_keypad_open() references
the function __devinit tc3589x_keypad_init_key_hardware().
This is often because tc3589x_keypad_open lacks a __devinit
annotation or the annotation of tc3589x_keypad_init_key_hardware is wrong.
Signed-off-by: Harvey Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For i2c drivers, we should use "i2c:" prefix for modalias.
MODULE_DEVICE_TABLE will setup the modulalias for us, thus adding
a MODULE_ALIAS is redundant (in addition to being incorrect).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
ep93xx_keypad.c uses interfaces from linux/module.h,
so it should include that file. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If kzalloc for kbc fails, then we have NULL pointer dereference while
calling input_free_device(kbc->idev) in the error handling.
So it is safer to always use the original name, input_dev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add missing device_remove_file() for dev_attr_time in lm8323_remove().
Also calling device_remove_file() in lm8323_probe() error path to
remove sysfs attribute file.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix a constant definition and computation of polling time.
[dtor@mail.ru: switched to using DIV_ROUND_UP as was suggested by
Thierry Reding <thierry.reding@avionic-design.de>]
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
Input: synaptics - fix reporting of min coordinates
Input: tegra-kbc - enable key autorepeat
Input: kxtj9 - fix locking typo in kxtj9_set_poll()
Input: kxtj9 - fix bug in probe()
Input: intel-mid-touch - remove pointless checking for variable 'found'
Input: hp_sdc - staticize hp_sdc_kicker()
Input: pmic8xxx-keypad - fix a leak of the IRQ during init failure
Input: cy8ctmg110_ts - set reset_pin and irq_pin from platform data
Input: cy8ctmg110_ts - constify i2c_device_id table
Input: cy8ctmg110_ts - fix checking return value of i2c_master_send
Input: lifebook - make dmi callback functions return 1
Input: atkbd - make dmi callback functions return 1
Input: gpio_keys - switch to using SIMPLE_DEV_PM_OPS
Input: gpio_keys - add support for device-tree platform data
Input: aiptek - remove double define
Input: synaptics - set minimum coordinates as reported by firmware
Input: synaptics - process button bits in AGM packets
Input: synaptics - rename set_slot to be more descriptive
Input: synaptics - fuzz position for touchpad with reduced filtering
Input: synaptics - set resolution for MT_POSITION_X/Y axes
...
To support key repeats, keyboard needs to be setup as an autorepeating
device.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make sure we are passing the same cookie in all calls to
request_any_context_irq() and free_irq().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We only care about if there is a successful match from the table (or
no match at all), so let's make dmi_check_system return immediately
instead of iterating thorough the whole table.
Make the dmi callback function return 1 then dmi_check_system
will return immediately if we have a successful match.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch enables fetching configuration data, which is normally provided
via platform_data, from the device-tree instead.
If the device is configured from device-tree data, the platform_data struct
is not used, and button data needs to be allocated dynamically. Big part of
this patch deals with confining pdata usage to the probe function, to make
this possible.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The "#if" above should really be an "#ifdef" to avoid this warning:
CC drivers/input/keyboard/sh_keysc.o
drivers/input/keyboard/sh_keysc.c:294:5: warning: "CONFIG_PM_SLEEP" is
not defined
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Quick Charge bit in Electrode conf register should be set in init
function. This bit was missed in chip's document, which may cause touch
controller charge too slow to generate an interrupt.
Also, adjust the default vlaue of touch and release threshold
to make touch key more sensitive, this fix touch may not sensitive
after setup with plastic case.
Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Initialize gpio_keys driver at late_initcall level, to give it a chance to
work with GPIO expanders that might not be ready yet if we initialize the
driver at module_init time.
This is strictly a band-aid until there is a better way to specify
inter-device dependencies.
Signed-off-by: David Jander <david@protonic.nl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the space between "platform:" prefix and the driver name.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/input/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use a threaded interrupt handler in order to permit the handler to use
a GPIO driver that causes things like I2C transactions being done inside
the handler context.
Signed-off-by: David Jander <david@protonic.nl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the data sheet the interrupt should be level rather than
edge triggered. This fixes the issue of the Nokia N810 keypad stopping
responding if multiple key events occur in quick succession.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need for that workqueue anymore. Get rid of it and move to
threaded IRQs instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A few new i2c-drivers came into the kernel which clear the clientdata
pointer on exit or error. This is not required anymore since the core
will do it for us.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sh_keysc - 8x8 MODE_6 fix
Input: omap-keypad - add missing input_sync()
Input: evdev - try to wake up readers only if we have full packet
Input: properly assign return value of clamp() macro.
According to the data sheet for G4, AP4 and AG5 KEYSC MODE_6 is 8x8 keys.
Bump up MAXKEYS to 64 too.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Otherwise the updated evdev driver (commit cdda911c34,
"Input: evdev - only signal polls on full packets") no longer works on
top of omap-keypad.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Atarimouse fails to load as a module (with ENODEV), due to a brown paper
bag bug, misinterpreting the semantics of atari_keyb_init().
[geert] Propagate the return value of atari_keyb_init() everywhere
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
From http://www.analog.com/ADP5589:
The ADP5589 is an I/O port expander and keypad matrix decoder designed
for QWERTY type phones that require a large keypad matrix and expanded
I/O lines.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds basic support for Freescale MPR121 capacitive touch
sensor. It's an i2c controller with up to 12 capacitance sensing inputs.
Product information (data sheet, application notes) can be found here:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPR121
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tegra hardware design cannot reliably support an arbitrary set of keys
waking up the system. Modify wakeup logic so either any key wakes the
system up or none will do.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the KEYSC driver to make use of threaded IRQs with IRQF_ONESHOT
to improve interrupt latency. The driver is using udelay() in the ISR
to make sure the hardware has stabilized. Without using interrupt threads
this delay may affect the latency of the rest of the system.
Also pass dev_name() as string for /proc/interrupts.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert the KEYSC driver from MSTP bit control through a magic clock
string to making use of Runtime PM.
Also, update the system suspend/resume callbacks to drop the Runtime
PM reference in the case of wakeup disabled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In current implementation, free_irq() was using NULL rather than the
driver data as the data pointer so free_irq() wouldn't have matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adding the necessary MODULE_DEVICE_TABLE() information allows the
driver to be automatically loaded by udev
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
This patch allows to set a device name which helps distinguishing several
gpio-keys devices.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With this patch you can setup a group of GPIOs representing a specific
position on an EV_ABS axis.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should return IRQ_NONE from interrupt handler in case keyboard
does not report DATA_AVAIL condition.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Extend the tca6416 driver to use enable_irq_wake() and disable_irq_wake()
in the suspend/resume hooks.
This makes it possible to wake up from suspend-to-ram using a tca6416 key
on the sh7372 mackerel board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The AT42QT1070 QTouch sensor supports up to 7 keys.
The driver has been tested on Atmel AT91SAM9M10-G45-EK board, and it
should work fine on other platforms.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MCS50XX series has a HW bug that requires explicit chip power down.
If chip is not powered down before shutting the system down the control
pins (powerup, interrupt) are pulled up and residue current continues
flowing into the chips making them continue consuming power.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable Runtime PM functionality in OMAP4 driver based on the following
assumptions:
- keyboard controller in wakeup domain so it is always on and power
impact is minimal;
- in OMAP4 the device control is at module/device level and ick/fclk
level control is difficult so cutting of clocks will prevent
interrupts.
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Arnd Bergmann