This is long overdue, and is part of cleaning up how we allocate kernel
sockets that don't reference count struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for tun to do the weird network namespace refcounting.
The existing network namespace refcounting in tfile has almost exactly
the same lifetime. So rewrite the code to use the struct sock network
namespace refcounting and remove the unnecessary hand rolled network
namespace refcounting and the unncesary tfile->net.
This change allows the tun code to directly call sock_put bypassing
sock_release and making SOCK_EXTERNALLY_ALLOCATED unnecessary.
Remove the now unncessary tun_release so that if anything tries to use
the sock_release code path the kernel will oops, and let us know about
the bug.
The macvtap code already uses it's internal socket this way.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DCTCP or similar ECN based deployments on fabrics with shallow
buffers, hosts are responsible for a good part of the buffering.
This patch adds an optional ce_threshold to codel & fq_codel qdiscs,
so that DCTCP can have feedback from queuing in the host.
A DCTCP enabled egress port simply have a queue occupancy threshold
above which ECT packets get CE mark.
In codel language this translates to a sojourn time, so that one doesn't
have to worry about bytes or bandwidth but delays.
This makes the host an active participant in the health of the whole
network.
This also helps experimenting DCTCP in a setup without DCTCP compliant
fabric.
On following example, ce_threshold is set to 1ms, and we can see from
'ldelay xxx us' that TCP is not trying to go around the 5ms codel
target.
Queue has more capacity to absorb inelastic bursts (say from UDP
traffic), as queues are maintained to an optimal level.
lpaa23:~# ./tc -s -d qd sh dev eth1
qdisc mq 1: dev eth1 root
Sent 87910654696 bytes 58065331 pkt (dropped 0, overlimits 0 requeues 42961)
backlog 3108242b 364p requeues 42961
qdisc codel 8063: dev eth1 parent 1:1 limit 1000p target 5.0ms ce_threshold 1.0ms interval 100.0ms
Sent 7363778701 bytes 4863809 pkt (dropped 0, overlimits 0 requeues 5503)
rate 2348Mbit 193919pps backlog 255866b 46p requeues 5503
count 0 lastcount 0 ldelay 1.0ms drop_next 0us
maxpacket 68130 ecn_mark 0 drop_overlimit 0 ce_mark 72384
qdisc codel 8064: dev eth1 parent 1:2 limit 1000p target 5.0ms ce_threshold 1.0ms interval 100.0ms
Sent 7636486190 bytes 5043942 pkt (dropped 0, overlimits 0 requeues 5186)
rate 2319Mbit 191538pps backlog 207418b 64p requeues 5186
count 0 lastcount 0 ldelay 694us drop_next 0us
maxpacket 68130 ecn_mark 0 drop_overlimit 0 ce_mark 69873
qdisc codel 8065: dev eth1 parent 1:3 limit 1000p target 5.0ms ce_threshold 1.0ms interval 100.0ms
Sent 11569360142 bytes 7641602 pkt (dropped 0, overlimits 0 requeues 5554)
rate 3041Mbit 251096pps backlog 210446b 59p requeues 5554
count 0 lastcount 0 ldelay 889us drop_next 0us
maxpacket 68130 ecn_mark 0 drop_overlimit 0 ce_mark 37780
...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xmit_mode 'netif_receive' for pktgen which generates the
packets using familiar pktgen commands, but feeds them into
netif_receive_skb() instead of ndo_start_xmit().
Default mode is called 'start_xmit'.
It is designed to test netif_receive_skb and ingress qdisc
performace only. Make sure to understand how it works before
using it for other rx benchmarking.
Sample script 'pktgen.sh':
\#!/bin/bash
function pgset() {
local result
echo $1 > $PGDEV
result=`cat $PGDEV | fgrep "Result: OK:"`
if [ "$result" = "" ]; then
cat $PGDEV | fgrep Result:
fi
}
[ -z "$1" ] && echo "Usage: $0 DEV" && exit 1
ETH=$1
PGDEV=/proc/net/pktgen/kpktgend_0
pgset "rem_device_all"
pgset "add_device $ETH"
PGDEV=/proc/net/pktgen/$ETH
pgset "xmit_mode netif_receive"
pgset "pkt_size 60"
pgset "dst 198.18.0.1"
pgset "dst_mac 90:e2:ba:ff:ff:ff"
pgset "count 10000000"
pgset "burst 32"
PGDEV=/proc/net/pktgen/pgctrl
echo "Running... ctrl^C to stop"
pgset "start"
echo "Done"
cat /proc/net/pktgen/$ETH
Usage:
$ sudo ./pktgen.sh eth2
...
Result: OK: 232376(c232372+d3) usec, 10000000 (60byte,0frags)
43033682pps 20656Mb/sec (20656167360bps) errors: 10000000
Raw netif_receive_skb speed should be ~43 million packet
per second on 3.7Ghz x86 and 'perf report' should look like:
37.69% kpktgend_0 [kernel.vmlinux] [k] __netif_receive_skb_core
25.81% kpktgend_0 [kernel.vmlinux] [k] kfree_skb
7.22% kpktgend_0 [kernel.vmlinux] [k] ip_rcv
5.68% kpktgend_0 [pktgen] [k] pktgen_thread_worker
If fib_table_lookup is seen on top, it means skb was processed
by the stack. To benchmark netif_receive_skb only make sure
that 'dst_mac' of your pktgen script is different from
receiving device mac and it will be dropped by ip_rcv
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow flag NO_TIMESTAMP to turn timestamping on again, like other flags,
with a negation of the flag like !NO_TIMESTAMP.
Also document the option flag NO_TIMESTAMP.
Fixes: afb84b6261 ("pktgen: add flag NO_TIMESTAMP to disable timestamping")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More accurately, listen all netns that have a nsid assigned into the netns
where the netlink socket is opened.
For this purpose, a netlink socket option is added:
NETLINK_LISTEN_ALL_NSID. When this option is set on a netlink socket, this
socket will receive netlink notifications from all netns that have a nsid
assigned into the netns where the socket has been opened. The nsid is sent
to userland via an anscillary data.
With this patch, a daemon needs only one socket to listen many netns. This
is useful when the number of netns is high.
Because 0 is a valid value for a nsid, the field nsid_is_set indicates if
the field nsid is valid or not. skb->cb is initialized to 0 on skb
allocation, thus we are sure that we will never send a nsid 0 by error to
the userland.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags and states have the same prefix (NETLINK_) that netlink socket
options. To avoid confusion and to be able to name a flag like a socket
option, let's use an other prefix: NETLINK_[S|F]_.
Note: a comment has been fixed, it was talking about
NETLINK_RECV_NO_ENOBUFS socket option instead of NETLINK_NO_ENOBUFS.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, nsid were protected by the rtnl lock. The goal of this
patch is to be able to find a nsid without needing to hold the rtnl lock.
The next patch will introduce a netlink socket option to listen to all
netns that have a nsid assigned into the netns where the socket is opened.
Thus, it's important to call rtnl_net_notifyid() outside the spinlock, to
avoid a recursive lock (nsid are notified via rtnl). This was the main
reason of the previous patch.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functional change with this patch. It will ease the refactoring
of the locking system that protects nsids and the support of the netlink
socket option NETLINK_LISTEN_ALL_NSID.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a following commit, a new function will be introduced to only lookup for
a nsid (no allocation if the nsid doesn't exist). To avoid confusion, the
existing function is renamed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this commit is to prepare the rework of the locking of nsnid
protection.
After this patch, rtnl_net_notifyid() will not call anymore __peernet2id(),
ie no idr_* operation into this function.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers of this function expect a nsid, not an error.
Thus, returns NETNSA_NSID_NOT_ASSIGNED in case of error so that callers
don't have to convert the error to NETNSA_NSID_NOT_ASSIGNED.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under tcp memory pressure, calling epoll_wait() in edge triggered
mode after -EAGAIN, can result in an indefinite hang in epoll_wait(),
even when there is sufficient memory available to continue making
progress. The problem is that when __sk_mem_schedule() returns 0
under memory pressure, we do not set the SOCK_NOSPACE flag in the
tcp write paths (tcp_sendmsg() or do_tcp_sendpages()). Then, since
SOCK_NOSPACE is used to trigger wakeups when incoming acks create
sufficient new space in the write queue, all outstanding packets
are acked, but we never wake up with the the EPOLLOUT that we are
expecting from epoll_wait().
This issue is currently limited to epoll() when used in edge trigger
mode, since 'tcp_poll()', does in fact currently set SOCK_NOSPACE.
This is sufficient for poll()/select() and epoll() in level trigger
mode. However, in edge trigger mode, epoll() is relying on the write
path to set SOCK_NOSPACE. EPOLL(7) says that in edge-trigger mode we
can only call epoll_wait() after read/write return -EAGAIN. Thus, in
the case of the socket write, we are relying on the fact that
tcp_sendmsg()/network write paths are going to issue a wakeup for
us at some point in the future when we get -EAGAIN.
Normally, epoll() edge trigger works fine when we've exceeded the
sk->sndbuf because in that case we do set SOCK_NOSPACE. However, when
we return -EAGAIN from the write path b/c we are over the tcp memory
limits and not b/c we are over the sndbuf, we are never going to get
another wakeup.
I can reproduce this issue, using SO_SNDBUF, since __sk_mem_schedule()
will return 0, or failure more readily with SO_SNDBUF:
1) create socket and set SO_SNDBUF to N
2) add socket as edge trigger
3) write to socket and block in epoll on -EAGAIN
4) cause tcp mem pressure via: echo "<small val>" > net.ipv4.tcp_mem
The fix here is simply to set SOCK_NOSPACE in sk_stream_wait_memory()
when the socket is non-blocking. Note that SOCK_NOSPACE, in addition
to waking up outstanding waiters is also used to expand the size of
the sk->sndbuf. However, we will not expand it by setting it in this
case because tcp_should_expand_sndbuf(), ensures that no expansion
occurs when we are under tcp memory pressure.
Note that we could still hang if sk->sk_wmem_queue is 0, when we get
the -EAGAIN. In this case the SOCK_NOSPACE bit will not help, since we
are waiting for and event that will never happen. I believe
that this case is harder to hit (and did not hit in my testing),
in that over the tcp 'soft' memory limits, we continue to guarantee a
minimum write buffer size. Perhaps, we could return -ENOSPC in this
case, or maybe we simply issue a wakeup in this case, such that we
keep retrying the write. Note that this case is not specific to
epoll() ET, but rather would affect blocking sockets as well. So I
view this patch as bringing epoll() edge-trigger into sync with the
current poll()/select()/epoll() level trigger and blocking sockets
behavior.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seccomp has always been a special candidate when it comes to preparation
of its filters in seccomp_prepare_filter(). Due to the extra checks and
filter rewrite it partially duplicates code and has BPF internals exposed.
This patch adds a generic API inside the BPF code code that seccomp can use
and thus keep it's filter preparation code minimal and better maintainable.
The other side-effect is that now classic JITs can add seccomp support as
well by only providing a BPF_LDX | BPF_W | BPF_ABS translation.
Tested with seccomp and BPF test suites.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When seccomp BPF was added, it was discussed to add __GFP_NOWARN
flag for their configuration path as f.e. up to 32K allocations are
more prone to fail under stress. As we're going to reuse BPF API,
add __GFP_NOWARN flags where larger kmalloc() and friends allocations
could fail.
It doesn't make much sense to pass around __GFP_NOWARN everywhere as
an extra argument only for seccomp while we just as well could run
into similar issues for socket filters, where it's not desired to
have a user application throw a WARN() due to allocation failure.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nicolas Schichan <nschichan@freebox.fr>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the calls to bpf_check_classic(), bpf_convert_filter() and
bpf_migrate_runtime() and let bpf_prepare_filter() take care of that
instead.
seccomp_check_filter() is passed to bpf_prepare_filter() so that it
gets called from there, after bpf_check_classic().
We can now remove exposure of two internal classic BPF functions
previously used by seccomp. The export of bpf_check_classic() symbol,
previously known as sk_chk_filter(), was there since pre git times,
and no in-tree module was using it, therefore remove it.
Joint work with Daniel Borkmann.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation for use by the seccomp code, the rationale is
not to duplicate additional code within the seccomp layer, but instead,
have it abstracted and hidden within the classic BPF API.
As an interim step, this now also makes bpf_prepare_filter() visible
(not as exported symbol though), so that seccomp can reuse that code
path instead of reimplementing it.
Joint work with Daniel Borkmann.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a lot of small fixes and cleanups, the bigger items are:
* proper mac80211 rate control locking, to fix some random crashes
(this required changing other locking as well)
* mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
amount of code we execute while going from ndo_start_xmit() to
the driver
* this also clears the way for properly supporting S/G and checksum
and segmentation offloads
-----BEGIN PGP SIGNATURE-----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=oUlh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next for this cycle. As usual, we have
a lot of small fixes and cleanups, the bigger items are:
* proper mac80211 rate control locking, to fix some random crashes
(this required changing other locking as well)
* mac80211 "fast-xmit", a mechanism to reduce, in most cases, the
amount of code we execute while going from ndo_start_xmit() to
the driver
* this also clears the way for properly supporting S/G and checksum
and segmentation offloads
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Diagnosing problems related to Window Probes has been hard because
we lack a counter.
TCPWinProbe counts the number of ACK packets a sender has to send
at regular intervals to make sure a reverse ACK packet opening back
a window had not been lost.
TCPKeepAlive counts the number of ACK packets sent to keep TCP
flows alive (SO_KEEPALIVE)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the advent of small rto timers in datacenter TCP,
(ip route ... rto_min x), the following can happen :
1) Qdisc is full, transmit fails.
TCP sets a timer based on icsk_rto to retry the transmit, without
exponential backoff.
With low icsk_rto, and lot of sockets, all cpus are servicing timer
interrupts like crazy.
Intent of the code was to retry with a timer between 200 (TCP_RTO_MIN)
and 500ms (TCP_RESOURCE_PROBE_INTERVAL)
2) Receivers can send zero windows if they don't drain their receive queue.
TCP sends zero window probes, based on icsk_rto current value, with
exponential backoff.
With /proc/sys/net/ipv4/tcp_retries2 being 15 (or even smaller in
some cases), sender can abort in less than one or two minutes !
If receiver stops the sender, it obviously doesn't care of very tight
rto. Probability of dropping the ACK reopening the window is not
worth the risk.
Lets change the base timer to be at least 200ms (TCP_RTO_MIN) for these
events (but not normal RTO based retransmits)
A followup patch adds a new SNMP counter, as it would have helped a lot
diagnosing this issue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy netlink API treated EPERM (permission denied) as
"operation not supported".
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to get or set the broadcast link window through the
new netlink API. The functionality was unintentionally missing from
the new netlink API. Adding this means that we also fix the breakage
in the old API when coming through the compat layer.
Fixes: 37e2d4843f (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default link properties can be set for media or bearer. This
functionality was missed when introducing the NL compatibility layer.
This patch implements this functionality in the compat netlink
layer. It works the same way as it did in the old API. We search for
media and bearers matching the "link name". If we find a matching
media or bearer the link tolerance, priority or window is used as
default for new links on that media or bearer.
Fixes: 37e2d4843f (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue:
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
=============================================
[ INFO: possible recursive locking detected ]
4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc
but task is already holding lock:
(_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
lock(_xmit_ETHER#2);
To avoid this, walk the tq queues of the dsa slaves and set a lockdep
class.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was missed in the previous patch, add some documentation
for rate_ctrl_lock to avoid docbook warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:
1. Allow the P2P GO to stay on its current channel. The rationale behind
this is that if the channel or UNII band were allowed by the AP they
could still be used to continue the P2P GO operation, and avoid connection
breakage.
2. Allow another P2P GO to start on the same channel or another channel
that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.
Fix two things:
* don't allow the driver to register anything longer than
the 16 bytes that mac80211 reserves space for
* require userspace to specify a starting value with the
correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "ntohs(proto) >= ETH_P_802_3_MIN" w/ eth_proto_is_802_3(proto).
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change does two things. First it fixes a sparse error for the fact
that the __be16 degrades to an integer. Since that is actually what I am
kind of doing I am simply working around that by forcing both sides of the
comparison to u16.
Also I realized on some compilers I was generating another instruction for
big endian systems such as PowerPC since it was masking the value before
doing the comparison. So to resolve that I have simply pulled the mask out
and wrapped it in an #ifndef __BIG_ENDIAN.
Lastly I pulled this all out into its own function. I notices there are
similar checks in a number of other places so this function can be reused
there to help reduce overhead in these paths as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a server application to get the TCP SYN headers for
its passive connections. This is useful if the server is doing
fingerprinting of clients based on SYN packet contents.
Two socket options are added: TCP_SAVE_SYN and TCP_SAVED_SYN.
The first is used on a socket to enable saving the SYN headers
for child connections. This can be set before or after the listen()
call.
The latter is used to retrieve the SYN headers for passive connections,
if the parent listener has enabled TCP_SAVE_SYN.
TCP_SAVED_SYN is read once, it frees the saved SYN headers.
The data returned in TCP_SAVED_SYN are network (IPv4/IPv6) and TCP
headers.
Original patch was written by Tom Herbert, I changed it to not hold
a full skb (and associated dst and conntracking reference).
We have used such patch for about 3 years at Google.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current (and planned, as far as I know) wifi devices support
encapsulation checksum offload, so remove the useless test here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When LED triggers are compiled in, but not used, mac80211 will still
call them to update the status. This isn't really a problem for the
assoc and radio ones, but the TX/RX (and to a certain extend TPT)
ones can be called very frequently (for every packet.)
In order to avoid that when they're not used, track their activation
and call the corresponding trigger (and in the TPT case, account for
throughput) only when the trigger is actually used by an LED.
Additionally, make those trigger functions inlines since theyre only
used once in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove items that can be retrieved through nl80211. This also
removes two items (tx_packets and tx_bytes) where only the VO
counter was exposed since they are split up per AC but in the
debugfs file only the first AC was shown.
Also remove the useless "dev" file - the stations have long
been in a sub-directory of the netdev so there's no need for
that any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This counter is unsafe with concurrent TX and is only exposed
through debugfs and ethtool. Instead of trying to fix it just
remove it for now, if it's really needed then it should be
exposed through nl80211 and in a way that drivers that do the
fragmentation in the device could support it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since these counters can only be read through debugfs, there's
very little point in maintaining them all the time. However,
even just making them depend on debugfs is pointless - they're
not normally used. Additionally a number of them aren't even
concurrency safe.
Move them under MAC80211_DEBUG_COUNTERS so they're normally
not even compiled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs statistics macros are pointlessly verbose, so change
that macro to just have a single argument. While at it, remove
the unused counters and rename rx_expand_skb_head2 to the better
rx_expand_skb_head_defrag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
> net/core/skbuff.c:4108:13: sparse: incorrect type in assignment (different base types)
> net/ipv6/mcast_snoop.c:63 ipv6_mc_check_exthdrs() warn: unsigned 'offset' is never less than zero.
Introduced by 9afd85c9e4
("net: Export IGMP/MLD message validation code")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once tipc_conn_new() returns NULL, the connection should be shut
down immediately, otherwise, oops may happen due to the NULL pointer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently subscriber's lock protects not only subscriber's subscription
list but also all subscriptions linked into the list. However, as all
members of subscription are never changed after they are initialized,
it's unnecessary for subscription to be protected under subscriber's
lock. If the lock is used to only protect subscriber's subscription
list, the adjustment not only makes the locking policy simpler, but
also helps to avoid a deadlock which may happen once creating a
subscription is failed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present subscriber's lock is used to protect the subscription list
of subscriber as well as subscriptions linked into the list. While one
or all subscriptions are deleted through iterating the list, the
subscriber's lock must be held. Meanwhile, as deletion of subscription
may happen in subscription timer's handler, the lock must be grabbed
in the function as well. When subscription's timer is terminated with
del_timer_sync() during above iteration, subscriber's lock has to be
temporarily released, otherwise, deadlock may occur. However, the
temporary release may cause the double free of a subscription as the
subscription is not disconnected from the subscription list.
Now if a reference counter is introduced to subscriber, subscription's
timer can be asynchronously stopped with del_timer(). As a result, the
issue is not only able to be fixed, but also relevant code is pretty
readable and understandable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing a new function makes the purpose of tipc_subscrb_connect_cb
callback routine more clear.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a topology server accepts a connection request from its client,
it allocates a connection instance and a tipc_subscriber structure
object. The former is used to communicate with client, and the latter
is often treated as a subscriber which manages all subscription events
requested from a same client. When a topology server receives a request
of subscribing name services from a client through the connection, it
creates a tipc_subscription structure instance which is seen as a
subscription recording what name services are subscribed. In order to
manage all subscriptions from a same client, topology server links
them into the subscrp_list of the subscriber. So subscriber and
subscription completely represents different meanings respectively,
but function names associated with them make us so confused that we
are unable to easily tell which function is against subscriber and
which is to subscription. So we want to eliminate the confusion by
renaming them.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
