In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ar933x_config_rs485() the check for the RTS GPIO is not needed since in
case the GPIO is not available at driver init ar933x_no_rs485 is assigned
to port->rs485_supported and this function is never called. So remove the
check.
Also in uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port. So remove the assignment in the
drivers rs485_config() function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-3-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 is not possible without an RTS GPIO regardless of whether RS485 is
enabled at boot time or not. So correct the concerning check in the probe()
function.
Fixes: e849145e1f ("serial: ar933x: Fill in rs485_supported")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-2-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.
Fixes: 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming from S2")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714031316.404918-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20220713131722.2316829-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S3C2410_UCON is a 32bit register, so it must be read with rd_regl()
instead of rd_reg(), otherwise the upper bits will be zeroed. Fix this.
Fixes: 72a43046b6 ("tty: serial: samsung_tty: loopback mode support")
Tested-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220712140745.30362-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/259138c372d433005b4871789ef9ee8d15320307.1657528861.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564669252BDC59BF55A6E87C4879@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SERIAL_BCM63XX depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is a race in pty_write(). pty_write() can be called in parallel
with e.g. ioctl(TIOCSTI) or ioctl(TCXONC) which also inserts chars to
the buffer. Provided, tty_flip_buffer_push() in pty_write() is called
outside the lock, it can commit inconsistent tail. This can lead to out
of bounds writes and other issues. See the Link below.
To fix this, we have to introduce a new helper called
tty_insert_flip_string_and_push_buffer(). It does both
tty_insert_flip_string() and tty_flip_buffer_commit() under the port
lock. It also calls queue_work(), but outside the lock. See
71a174b39f (pty: do tty_flip_buffer_push without port->lock in
pty_write) for the reasons.
Keep the helper internal-only (in drivers' tty.h). It is not intended to
be used widely.
Link: https://seclists.org/oss-sec/2022/q2/155
Fixes: 71a174b39f (pty: do tty_flip_buffer_push without port->lock in pty_write)
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will need this new helper in the next patch.
Cc: Hillf Danton <hdanton@sina.com>
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmld_poll() currently fails to handle the following corner cases correctly:
- remote party closed the associated tty
Add the missing checks and map those to EPOLLHUP.
Reorder the checks to group them by their reaction.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation constipates all transmission paths during flow
control except for flow control frames. However, these may not be located
at the beginning of the transmission queue of the control channel.
Ensure that flow control frames in the transmission queue for the control
channel are always handled even if constipated by skipping through other
messages.
Fixes: 0af021678d ("tty: n_gsm: fix deadlock and link starvation in outgoing data path")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DT provides rs485-term, set termination flag as supported.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.
So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.
To weaken this problem restrict saving LSR to only the BI bit.
Note however that the handling is still broken:
- lsr_saved_flags is updated using orig_lsr which is the LSR content
for the first received char, but there might be more in the FIFO, so
a character is thrown away that is received later and not necessarily
the one following the break.
- The doubled break might be the 2nd and 3rd char in the FIFO, so the
workaround doesn't catch these, because serial8250_rx_chars() doesn't
handle the workaround.
- lsr_saved_flags might have set UART_LSR_BI at the entry of
fsl8250_handle_irq() which doesn't originate from
fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
- For a long or a short break this isn't about two characters, but more
or only a single one.
Fixes: 9deaa53ac7 ("serial: add irq handler for Freescale 16550 errata.")
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220704085119.55900-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Within gsm_activate_mux() all timers and locks are initiated before the
actual resource for the control channel is allocated. This can lead to race
conditions.
Allocate the control channel DLCI object first to avoid race conditions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation queues up new control and user packets as needed
and processes this queue down to the ldisc in the same code path.
That means that the upper and the lower layer are hard coupled in the code.
Due to this deadlocks can happen as seen below while transmitting data,
especially during ldisc congestion. Furthermore, the data channels starve
the control channel on high transmission load on the ldisc.
Introduce an additional control channel data queue to prevent timeouts and
link hangups during ldisc congestion. This is being processed before the
user channel data queue in gsm_data_kick(), i.e. with the highest priority.
Put the queue to ldisc data path into a workqueue and trigger it whenever
new data has been put into the transmission queue. Change
gsm_dlci_data_sweep() accordingly to fill up the transmission queue until
TX_THRESH_HI. This solves the locking issue, keeps latency low and provides
good performance on high data load.
Note that now all packets from a DLCI are removed from the internal queue
if the associated DLCI was closed. This ensures that no data is sent by the
introduced write task to an already closed DLCI.
BUG: spinlock recursion on CPU#0, test_v24_loop/124
lock: serial8250_ports+0x3a8/0x7500, .magic: dead4ead, .owner: test_v24_loop/124, .owner_cpu: 0
CPU: 0 PID: 124 Comm: test_v24_loop Tainted: G O 5.18.0-rc2 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x34/0x44
do_raw_spin_lock+0x76/0xa0
_raw_spin_lock_irqsave+0x72/0x80
uart_write_room+0x3b/0xc0
gsm_data_kick+0x14b/0x240 [n_gsm]
gsmld_write_wakeup+0x35/0x70 [n_gsm]
tty_wakeup+0x53/0x60
tty_port_default_wakeup+0x1b/0x30
serial8250_tx_chars+0x12f/0x220
serial8250_handle_irq.part.0+0xfe/0x150
serial8250_default_handle_irq+0x48/0x80
serial8250_interrupt+0x56/0xa0
__handle_irq_event_percpu+0x78/0x1f0
handle_irq_event+0x34/0x70
handle_fasteoi_irq+0x90/0x1e0
__common_interrupt+0x69/0x100
common_interrupt+0x48/0xc0
asm_common_interrupt+0x1e/0x40
RIP: 0010:__do_softirq+0x83/0x34e
Code: 2a 0a ff 0f b7 ed c7 44 24 10 0a 00 00 00 48 c7 c7 51 2a 64 82 e8 2d
e2 d5 ff 65 66 c7 05 83 af 1e 7e 00 00 fb b8 ff ff ff ff <49> c7 c2 40 61
80 82 0f bc c5 41 89 c4 41 83 c4 01 0f 84 e6 00 00
RSP: 0018:ffffc90000003f98 EFLAGS: 00000286
RAX: 00000000ffffffff RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff82642a51 RDI: ffffffff825bb5e7
RBP: 0000000000000200 R08: 00000008de3271a8 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000030 R14: 0000000000000000 R15: 0000000000000000
? __do_softirq+0x73/0x34e
irq_exit_rcu+0xb5/0x100
common_interrupt+0xa4/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x1e/0x40
RIP: 0010:_raw_spin_unlock_irqrestore+0x2e/0x50
Code: 00 55 48 89 fd 48 83 c7 18 53 48 89 f3 48 8b 74 24 10 e8 85 28 36 ff
48 89 ef e8 cd 58 36 ff 80 e7 02 74 01 fb bf 01 00 00 00 <e8> 3d 97 33 ff
65 8b 05 96 23 2b 7e 85 c0 74 03 5b 5d c3 0f 1f 44
RSP: 0018:ffffc9000020fd08 EFLAGS: 00000202
RAX: 0000000000000000 RBX: 0000000000000246 RCX: 0000000000000000
RDX: 0000000000000004 RSI: ffffffff8257fd74 RDI: 0000000000000001
RBP: ffff8880057de3a0 R08: 00000008de233000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000100 R14: 0000000000000202 R15: ffff8880057df0b8
? _raw_spin_unlock_irqrestore+0x23/0x50
gsmtty_write+0x65/0x80 [n_gsm]
n_tty_write+0x33f/0x530
? swake_up_all+0xe0/0xe0
file_tty_write.constprop.0+0x1b1/0x320
? n_tty_flush_buffer+0xb0/0xb0
new_sync_write+0x10c/0x190
vfs_write+0x282/0x310
ksys_write+0x68/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f3e5e35c15c
Code: 8b 7c 24 08 89 c5 e8 c5 ff ff ff 89 ef 89 44 24 08 e8 58 bc 02 00 8b
44 24 08 48 83 c4 10 5d c3 48 63 ff b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff
ff 76 10 48 8b 15 fd fc 05 00 f7 d8 64 89 02 48 83
RSP: 002b:00007ffcee77cd18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007ffcee77cd70 RCX: 00007f3e5e35c15c
RDX: 0000000000000100 RSI: 00007ffcee77cd90 RDI: 0000000000000003
RBP: 0000000000000100 R08: 0000000000000000 R09: 7efefefefefefeff
R10: 00007f3e5e3bddeb R11: 0000000000000246 R12: 00007ffcee77ce8f
R13: 0000000000000001 R14: 000056214404e010 R15: 00007ffcee77cd90
</TASK>
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Fixes: c01af4fec2 ("n_gsm : Flow control handling in Mux driver")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation does not handle the situation that no data is in
the internal queue and needs to be sent out while the user tty fifo is
full.
Add a timer that moves more data from user tty down to the internal queue
which is then serialized on the ldisc. This timer is triggered if no data
was moved from a user tty to the internal queue within 10 * T1.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The function drains the fifo for the given user tty/DLCI without
considering 'TX_THRESH_HI' and different to gsm_dlci_data_output_framed(),
which moves only one packet from the user side to the internal transmission
queue. We can only handle one packet at a time here if we want to allow
DLCI priority handling in gsm_dlci_data_sweep() to avoid link starvation.
2) Furthermore, the additional header octet from convergence layer type 2
is not counted against MTU. It is part of the UI/UIH frame message which
needs to be limited to MTU. Hence, it is wrong not to consider this octet.
3) Finally, the waiting user tty is not informed about freed space in its
send queue.
Take at most one packet worth of data out of the DLCI fifo to fix 1).
Limit the max user data size per packet to MTU - 1 in case of convergence
layer type 2 to leave space for the control signal octet which is added in
the later part of the function. This fixes 2).
Add tty_port_tty_wakeup() to wake up the user tty if new write space has
been made available to fix 3).
Fixes: 268e526b93 ("tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Fixes: d50f6dcaf2 ("tty: n_gsm: expose gsmtty device nodes at ldisc open time")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After setting up the control channel on both sides the responder side may
want to open a virtual tty to listen on until the initiator starts an
application on a user channel. The current implementation allows the
open() but no other operation, like termios. These fail with EINVAL.
The responder sided application has no means to detect an open by the
initiator sided application this way. And the initiator sided applications
usually expect the responder sided application to listen on the user
channel upon open.
Set the user channel into half-open state on responder side once a user
application opens the virtual tty to allow IO operations on it.
Furthermore, keep the user channel constipated until the initiator side
opens it to give the responder sided application the chance to detect the
new connection and to avoid data loss if the responder sided application
starts sending before the user channel is open.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/N1 peripheral user manual(r01uh0752ej0100-rzn1-peripheral.pdf)
rev 1.0.0 Mar,2019, the value for 8_WORD_BURST is 4(b2,b1=2’b10).
This patch fixes the macro as per the user manual.
Fixes: aa63d786ce ("serial: 8250: dw: Add support for DMA flow controlling devices")
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220630083909.4294-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A memory overlapping copy occurs when deleting a long line. This memory
overlapping copy can cause data corruption when scr_memcpyw is optimized
to memcpy because memcpy does not ensure its behavior if the destination
buffer overlaps with the source buffer. The line buffer is not always
broken, because the memcpy utilizes the hardware acceleration, whose
result is not deterministic.
Fix this problem by using replacing the scr_memcpyw with scr_memmovew.
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Signed-off-by: Yangxi Xiang <xyangxi5@gmail.com>
Link: https://lore.kernel.org/r/20220628093322.5688-1-xyangxi5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
be called with the baudrate value which was set to hardware. Linux then
report exact values via ioctl(TCGETS2) to userspace.
Change mvebu_uart_baud_rate_set() function to return baudrate value which
was set to hardware and propagate this value to above mentioned functions.
With this change userspace would see precise value in termios c_ospeed
field.
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220628100922.10717-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When console is enabled, univ8250_console_setup() calls
serial8250_console_setup() before .dev is set to uart_port. Therefore,
it will not call pm_runtime_get_sync(). Later, when the actual driver
is going to take over univ8250_console_exit() is called. As .dev is
already set, serial8250_console_exit() makes pm_runtime_put_sync() call
with usage count being zero triggering PM usage count warning
(extra debug for univ8250_console_setup(), univ8250_console_exit(), and
serial8250_register_ports()):
[ 0.068987] univ8250_console_setup ttyS0 nodev
[ 0.499670] printk: console [ttyS0] enabled
[ 0.717955] printk: console [ttyS0] printing thread started
[ 1.960163] serial8250_register_ports assigned dev for ttyS0
[ 1.976830] printk: console [ttyS0] disabled
[ 1.976888] printk: console [ttyS0] printing thread stopped
[ 1.977073] univ8250_console_exit ttyS0 usage:0
[ 1.977075] serial8250 serial8250: Runtime PM usage count underflow!
[ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A
[ 1.977812] univ8250_console_setup ttyS0 usage:2
[ 1.978167] printk: console [ttyS0] printing thread started
[ 1.978203] printk: console [ttyS0] enabled
To fix the issue, call pm_runtime_get_sync() in
serial8250_register_ports() as soon as .dev is set for an uart_port
if it has console enabled.
This problem became apparent only recently because 82586a7215 ("PM:
runtime: Avoid device usage count underflows") added the warning
printout. I confirmed this problem also occurs with v5.18 (w/o the
warning printout, obviously).
Fixes: bedb404e91 ("serial: 8250_port: Don't use power management for kernel console")
Cc: stable <stable@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/b4f428e9-491f-daf2-2232-819928dc276e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port->mapbase = NULL in serial8250_request_std_resource() , it need
return a error code instead of 0. If uart_set_info() fail to request new
regions by serial8250_request_std_resource() but the return value of
serial8250_request_std_resource() is 0, The system incorrectly considers
that the resource application is successful and does not attempt to
restore the old setting. A null pointer reference is triggered when the
port resource is later invoked.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220628083515.64138-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code lacks clearing of previous DEAT/DEDT values. Thus, changing
values on the fly results in garbage delays tending towards the maximum
value as more and more bits are ORed together. (Leaving RS485 mode
would have cleared the old values though).
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220627150753.34510-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Place dw8250_serial_out() before dw8250_serial_out38x() so that it can
be called from dw8250_serial_out38x() to do the actual write.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220628134234.53771-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of open-coding, use BIT(), GENMASK(), and FIELD_GET() helpers.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220630100536.41329-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop CONFIG_PM and CONFIG_PM_SLEEP ifdeffery while converting dw8250_pm_ops
to use new PM macros. Since we are using runtime PM, wrap dw8250_pm_ops into
pm_ptr().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220630100507.31113-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the sake of better maintenance, sort included headers alphabetically.
While at it, split the serial group of headers which makes clear the
subsystem the driver belongs to.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220630093816.28271-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the earlycon parameter is given twice, the kernel will spit out a
WARN() in register_console() because it was already registered. The
non-dt variant setup_earlycon() already handles that gracefully. The dt
variant of_setup_earlycon() doesn't. Add the check there and add the
-EALREADY handling in early_init_dt_scan_chosen_stdout().
FWIW, this doesn't happen if CONFIG_ACPI_SPCR_TABLE is set. In that case
the registration is delayed until after earlycon parameter(s) are
parsed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220628120705.200617-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing LSR requires port lock because it mutates lsr_saved_flags
in serial_lsr_in().
Fixes: 197eb5c416 ("serial: 8250_dw: Use serial_lsr_in() in dw8250_handle_irq()")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/c5879db7-bee9-93f-526e-872a292442@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal loopback mode can be supported by setting
UCON register's Loopback Mode bit. The mode & bit can be supported
since s3c2410 and later SoCs. The prefix of LOOPBACK / BIT(5) naming
should be also changed to S3C2410_ in order to avoid confusion.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629004141.51484-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regarding Exynos Auto v9 SoC, it supports uarts up to 12. However, the
maximum number of the ports has been derived from
CONFIG_SERIAL_SAMSUNG_UARTS and tightly coupled with the config for
previous Samsung SoCs such as s3c24xx and s3c64xx. To overcome this
limitation, this changes the usage of the definition to UART_NR which is
widely used from other serial drivers. This also defines the value to 12
only for ARM64 SoCs to not affect the change to previous arm32 SoCs.
Instead of enumerating all the ports as predefined arrays, this
introduces s3c24xx_serial_init_port_default that is initializing the
structure as the default value.
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629005538.60132-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with
DMA") changed __dma_tx_complete() to enable THRI that is cleared in
__stop_tx() once THRE is asserted as UART runs out bits to transmit. It
is possible, however, that more data arrives in between in which case
serial8250_tx_dma() resumes Tx. THRI is not supposed to be on during
DMA Tx because DMA is based on completion handler, therefore THRI must
be cleared unconditionally in serial8250_tx_dma().
When Tx is about to start, another race window exists with
serial8250_handle_irq() leading to a call into __stop_tx() while the
Tx has already been resumed:
__tx_complete():
-> spin_lock(port->lock)
-> dma->tx_running = 0
-> serial8250_set_THRI()
-> spin_unlock(port->lock)
uart_start():
serial8250_handle_irq():
-> spin_lock(port->lock)
-> serial8250_tx_dma():
-> dma->tx_running = 1
-> spin_unlock(port->lock)
-> spin_lock(port->lock)
-> __stop_tx()
Close this race by checking !dma->tx_running before calling into
__stop_tx().
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220615090651.15340-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver must provide throttle and unthrottle in uart_ops when it
sets UPSTAT_AUTORTS. Add them using existing stop_rx &
enable_interrupts functions.
Fixes: 2a76fa2830 (serial: pl011: Adopt generic flag to store auto RTS status)
Cc: stable <stable@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Tested-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220614075637.8558-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The src_maxburst and dst_maxburst have been changed to 1 but the settings
of the UCON register aren't changed yet. They should be changed as well
according to the dmaengine slave config.
Fixes: aa2f80e752 ("serial: samsung: fix maxburst parameter for DMA transactions")
Cc: stable <stable@kernel.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627065113.139520-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
caused NULL-pointer dereference when booting with ACPI by unconditional
usage of the recently added pdata.
In order to fix that and prevent similar issues in future, hook the
default version of this structure in dw8250_acpi_match table.
While at it, sort all entries alphabetically.
Fixes: ffd381445e ("serial: 8250: dw: Move the USR register to pdata")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220620121046.1307412-1-mw@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 9th bit multipoint addressing mode for DW UART. 9th bit addressing
can be used only when HW RS485 is available.
Updating RAR (receive address register) is bit tricky because busy
indication is not be available when DW UART is strictly 16550
compatible, which is the case with the hardware I was testing with. RAR
should not be updated while receive is in progress which is now
achieved by deasserting RE and waiting for one frame (in case rx would
be in progress, the driver seems to have no way of knowing it w/o busy
indication). Because of this complexity, it's better to avoid doing it
unless really needed.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Co-developed-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.
Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per file BOTH_EMPTY defines are littering our source code here and
there. Define once in serial.h and create helper for the check
too.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both UART_XMIT_SIZE and SERIAL_XMIT_SIZE are defined. Make them all
UART_XMIT_SIZE.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use C99 array initializer insteads of comments and make unmapped checks
more obvious.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using UART_* to name defines is a bit problematic. When trying to do
unrelated cleanup which also involved tweaking header inclusion logic,
caused UART_CSR from serial_reg.h to leak into msm's namespace which is
also among msm defines. Thus, rename all UART_* ones to MSM_UART_* to
eliminate possibility of collisions.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create static inline instead of define as it provides type safety and
is safer wrt. macros expansion.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624205424.12686-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for clk_prepare_enable() at the beginning of
atmel_console_setup() and clk_disable_unprepare() at the end of
atmel_console_setup() as the clock is already enabled when calling
atmel_console_setup() and its disablement is done at the end
of probe.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-4-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get() for serial clock instead of clk_get()/clk_put().
With this move the clk_get in driver's probe function.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-3-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using legacy PM ops and switch using dev_pm_ops. Along with
it #ifdef CONFIG_PM are removed and __maybe_unused and pm_ptr() used
instead. Coding style recommends (at chapter Conditional Compilation)
to avoid using preprocessor conditional and use __maybe_unused
instead.
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616140024.2081238-2-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In soc_info(), of_find_node_by_type() will return a node pointer
with refcount incremented. We should use of_node_put() when it is
not used anymore.
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220618060850.4058525-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tegra_uart_init(), of_find_matching_node() will return a node
pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220615111747.3963930-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31f6bd7fad ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.
Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code expects "translations" to have 256 (E_TABSZ) values. Use the
macro instead of the constant to be explicit about this.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con_do_clear_unimap() sets dflt to NULL and then calls
con_release_unimap() which does the very same as the first thing. So
remove the former as it is apparently superfluous.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use FIELD_GET() and GENMASK() helpers instead of direct shifts and ANDs.
This makes the code even more obvious. I didn't know about the helpers
at the time of writing the macros.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a follow-up to the commit 4173f018aa (tty/vt: consolemap: rename
and document struct uni_pagedir), rename also the members of struct
vc_data. I.e. pagedir -> pagedict. And while touching all the places,
remove also the unnecessary vc_ prefix.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function still uses too vague parameter name after commit
50c92a1b2d (tty/vt: consolemap: saner variable names in
set_inverse_trans_unicode()).
So use "dict" instead of "p" for that parameter too.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code still uses constants (macros) as bounds in loops after commit
17945d317a (tty/vt: consolemap: use ARRAY_SIZE()). The contants are at
least macros used also in the definition of the arrays. But use
ARRAY_SIZE() on two more places to ensure the loops never run out of
bounds even if the array definition change.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2bb2b7b57f.
The testing of 5.19 release candidates revealed missing synchronization
between early and regular console functionality.
It would be possible to start the console kthreads later as a workaround.
But it is clear that console lock serialized console drivers between
each other. It opens a big area of possible problems that were not
considered by people involved in the development and review.
printk() is crucial for debugging kernel issues and console output is
very important part of it. The number of consoles is huge and a proper
review would take some time. As a result it need to be reverted for 5.19.
Link: https://lore.kernel.org/r/YrBdjVwBOVgLfHyb@alley
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20220623145157.21938-7-pmladek@suse.com
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge tag 'v5.19-rc3' into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable MMIO tracing for geni serial driver to prevent excessive
logging. Any access over serial console would involve a lot of
TX and RX register accesses (and few others), so these MMIO
read/write trace events in these drivers cause a lot of unwanted
noise because of the high frequency of such operations and it is
not very useful tracing these events for such drivers.
Given we want to enable these trace events on development devices
(maybe not production devices) where performance also really matters
so that we don't regress other components by wasting CPU cycles and
memory collecting these traces, it makes more sense to disable these
traces from such drivers.
Also another reason to disable these traces would be to prevent
recursive tracing when we display the trace buffer containing
these MMIO trace events since writing onto serial console would
further record MMIO traces.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102a ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Cc: stable <stable@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@penugtronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/f4d774be-1437-a550-8334-19d8722ab98c@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use n_tty_receive_char_flow_ctrl also on the closing path. This makes
the code cleaner and consistent.
However, there a small change of regression!
The earlier closing path has a small difference compared with the
normal receive path. If START_CHAR and STOP_CHAR are equal, their
precedence is different depending on which path a character is
processed. I don't know whether this difference was intentional or
not, and if equal START_CHAR and STOP_CHAR is actually used anywhere.
But it feels not so useful corner case.
While this change would logically belong to those earlier changes,
having a separate patch for this is useful. If this regresses, bisect
can pinpoint this change rather than the large patch. Also, this
change is not necessary to minimal fix for the issue addressed in
the previous patch.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606153652.63554-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tty is not read from, XON/XOFF may get stuck into an
intermediate buffer. As those characters are there to do software
flow-control, it is not very useful. In the case where neither end
reads from ttys, the receiving ends might not be able receive the
XOFF characters and just keep sending more data to the opposite
direction. This problem is almost guaranteed to occur with DMA
which sends data in large chunks.
If TTY is slow to process characters, that is, eats less than given
amount in receive_buf, invoke lookahead for the rest of the chars
to process potential XON/XOFF characters.
We need to keep track of how many characters have been processed by the
lookahead to avoid processing the flow control char again on the normal
path. Bookkeeping occurs parallel on two layers (tty_buffer and n_tty)
to avoid passing the lookahead_count through the whole call chain.
When a flow-control char is processed, two things must occur:
a) it must not be treated as normal char
b) if not yet processed, flow-control actions need to be taken
The return value of n_tty_receive_char_flow_ctrl() tells caller a), and
b) is kept internal to n_tty_receive_char_flow_ctrl().
If characters were previous looked ahead, __receive_buf() makes two
calls to the appropriate n_tty_receive_buf_* function. First call is
made with lookahead_done=true for the characters that were subject to
lookahead earlier and then with lookahead=false for the new characters.
Either of the calls might be skipped when it has no characters to
handle.
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606153652.63554-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 assignment. It is safe to remove this
assignment because sc16is7xx_reg_proc() takes port.lock at start (and
sc16is7xx_reconf_rs485() would too).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-36-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver provides different rs485_supported for the case where RTS is
not available making it unnecessary to handle it in
imx_uart_rs485_config.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-32-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.
This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial core handles serial_rs485 sanitization and rs485 struct
assignment. As serial_rs485 is already clear for the non-RS485 case by
serial core, there no need to clear flags in the driver.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-26-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to be add new flags more cleanly and safely, return -EINVAL
from TIOCSRS485 ioctl for the flags bits which are not among the
current legacy ones.
This might cause a regression for userspace as those non-flag bits do
not currently trigger -EINVAL. However, it would only occur if the
userspace is sending garbage bits so perhaps we'll get away with this
change.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-25-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SER_RS485_ENABLED is not set, having any other flag/field set in
serial_rs485 struct does not have an effect different from not having
them set. Thus, make the serial_rs485 struct also match the behavior
for all flags, not just SER_RS485_ENABLED.
Some drivers do similar clearing of rs485 struct in their
rs485_config() already, but not all. This change makes the behavior
consistent across drivers.
Don't try to validate rs485 struct further when no RS485 is requested,
this silences some bogus warnings.
This change has (minor) userspace visible impact.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-24-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanitize serial_rs485 struct before calling into rs485_setup. The
drivers provide supported_rs485 to help sanitization of the fields.
If neither of SER_RS485_RTS_ON_SEND or SER_RS485_RTS_AFTER_SEND
supported, don't pretend they can be set to sane settings but clear
them both instead. If only one of them is supported it may look
tempting to use the one driver supports to set the other, however, the
userspace does not have that information readily available so it
wouldn't be helpful.
While adjusting the documentation, remove also the claim that
TIOCGRS485 would call driver specific code. In reality, it does nothing
else than copies the stored serial_rs485 structure from uart_port to
userspace.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-23-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
