Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner value set by mtdcore.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The BRCM NAND driver can be re-used for Broadcom ARM64 SoCs hence
this patch updates Kconfig to allow selection of MTD_NAND_BRCMNAND
for ARM64.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Pramod KUMAR <pramodku@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should always type-cast pointer to "long" or "unsigned long"
because size of pointer is same as machine word size. This will
avoid pointer type-cast issues on both 32bit and 64bit systems.
This patch fixes pointer type-cast issue in brcmnand_write()
as-per above info.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to LPC32xx User's Manual all values measured in clock cycles
are programmable from 1 to 16 clocks (4 bits) starting from 0 in
bitfield, the current version of calculated clock cycles is too
conservative.
Correctness of 0 bitfield value (i.e. programmed 1 clock
timing) is proven with actual NAND chip devices.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case if quotient of controller clock rate to device clock rate does
not fit into 4 bit value, choose the maximum acceptable value 0xF, which
stands for 16 clocks.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
No functional change, move bitfield calculations to macro
definitions with added clock rate argument, which are in turn defined
by new common SLCTAC_CLOCKS(c, n, s) macro definition.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the nand_check_erased_ecc_chunk() function to test if the ECC error
was triggered by an erased page containing a few bitflips.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
sunxi_nfc_user_data_to_buf() is exposed as an inline function, replace the
NFC_BUF_TO_USER_DATA() macro by an inline function to be consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ECC engine is protecting a few OOB bytes. Retrieve them from the
USER_DATA register instead of reading them in raw mode (ie without the ECC
protection).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add helper functions to factorize the code dealing extra OOB bytes in the
normal and syndrome ECC implementations.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nfc_hw_ecc_read/write_chunk() functions have been created to
factorize the code in the normal and syndrome ECC implementation.
Make use of them where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The logic behind normal and syndrome ECC handling is pretty much the same,
the only difference is the ECC bytes placement.
Create two functions to read/write ECC chunks. Those functions will later
be used by the sunxi_nfc_hw_ecc_read/write_page() and
sunxi_nfc_hw_syndrome_ecc_read/write_page() functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The code used to enable/disable the hardware ECC engine is repeated in a
lot of places. Create two functions to avoid code duplication.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ->init_size() hook was introduced to let NAND controller drivers
support NAND devices that could not be described in the nand_ids table.
Since then, the core has added support for extended-id parsing and
full-id description, thus allowing to describe pretty much all existing
NANDs.
Moreover, this hook is not used by any mainline driver, and should not be
used by new drivers, because detecting the NAND chip is not something
controller specific.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These really aren't needed, especially now that we embed the soc struct
in our private struct, so we can stash things there if needed.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Suffix mask macros with _MSK and add new helper macros to avoid manually
shifting values.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This must have been implicitly included on the builds I tested. Reported
by numerous test bots:
drivers/mtd/nand/vf610_nfc.c: In function 'vf610_nfc_resume':
drivers/mtd/nand/vf610_nfc.c:660:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
This adds hardware ECC support using the BCH encoder in the NFC IP.
The ECC encoder supports up to 32-bit correction by using 60 error
correction bytes. There is no sub-page ECC step, ECC is calculated
always across the whole page (up to 2k pages).
Limitations:
- HW ECC: Only 2K page with 64+ OOB.
- HW ECC: Only 24 and 32-bit error correction implemented.
Raw writes have been tested using the generic nand_write_page_raw
implementation. However, raw reads are currently not possible
because the controller need to know whether we are going to use
the ECC mode already at NAND_CMD_READ0 command time. At this point
we do not have the information whether it is a raw read or a
regular read at driver level...
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver supports Freescale NFC (NAND flash controller) found on
Vybrid (VF610), MPC5125, MCF54418 and Kinetis K70. The driver has
been tested using 8-bit and 16-bit NAND interface on the ARM based
Vybrid SoC VF500 and VF610 platform.
parameter page reading.
Limitations:
- Untested on MPC5125 and M54418.
- DMA and pipelining not used.
- 2K pages or less.
- No chip select, one NAND chip per controller.
- No hardware ECC.
Some paths have been hand-optimized and evaluated by measurements
made using mtd_speedtest.ko on a 100MB MTD partition.
Colibri VF50
eb write % eb read % page write % page read %
rel/opt 5175 11537 4560 11039
opt 5164 -0.21 11420 -1.01 4737 +3.88 10918 -1.10
none 5113 -1.20 11352 -1.60 4490 -1.54 10865 -1.58
Colibri VF61
eb write % eb read % page write % page read %
rel/opt 5766 13096 5459 12846
opt 5883 +2.03 13064 -0.24 5561 +1.87 12802 -0.34
none 5701 -1.13 12980 -0.89 5488 +0.53 12735 -0.86
rel = using readl_relaxed/writel_relaxed in optimized paths
opt = hand-optimized by combining multiple accesses into one read/write
The measurements have not been statistically verfied, hence use them
with care. The author came to the conclusion that using the relaxed
variants of readl/writel are not worth the additional code.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A read id operation followed by 0x00 reads the device ID while
a read id operation followed by 0x20 reads the possible ONFI identifier.
As the READID function did not propagate the second id parameter but had
a hard-coded call for 0x90 0x00, reading the ONFI identifier was not
possible and thus chips werde not detected (tested with
MT29F8G08ABABAWP)
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
After the conversion of pxa architecture to common clock framework, the
NAND clock can be disabled on driver exit.
In this case, it happens that if the driver used the NAND and set the
DFI arbitration bit, the next access to a static memory controller area,
such as an ethernet card, will stall the system bus, and the core will
be stalled forever.
This is especially true on pxa31x SoCs, where the NDCR was augmented
with a new bit to prevent this lockups by giving full ownership of the
DFI arbiter to the SMC, in change SCr#6.
Fix this by clearing the DFI arbritration bit in driver exit. This
effectively prevents a lockup on zylonite when removing pxa3xx-nand
module, and using ethernet afterwards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now pxa architecture has a dmaengine driver, remove the access to direct
dma registers in favor of the more generic dmaengine code.
This should be also applicable for mmp and orion, provided they work in
device-tree environment.
This patch also removes the previous hack which was necessary to make
the driver work in a devicetree environment.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Brian: fixup use of 'enum dma_transfer_direction']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The sunxi_nand_chips_cleanup() function is missing a call to list_del()
which generates a double free error.
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add two helper functions to help NAND controller drivers test whether a
specific NAND region is erased or not.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The USER_DATA register cannot be accessed using byte accessors on A13
SoCs, thus triggering a bug when using memcpy_toio on this register.
Declare an helper macros to convert an OOB buffer into a suitable
USER_DATA value and vice-versa.
This patch also fixes an error in the oob_required logic (some OOB data
are not written even if the user required it) by removing the
oob_required condition, which is perfectly valid since the core already
fill ->oob_poi with FFs when oob_required is false.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_dt_init(), called from nand_scan_ident(), is already parsing the
generic MTD/NAND DT properties, and initializing the nand_chip struct
accordingly.
Rely on this initialization instead of manually parsing those properties.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: rename 'np' -> 'flash_node' to accomodate for prior rename patch]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use a more descriptive name for the device_node element in struct nand_chip .
This name matches the element name used for device_node property of a flash
in the spi-nor framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_scan_ident() leaves the chip deselected. So just issuing some commands
from the sunxi driver does not work. We need to select the chip before
writing the commands to the NAND device. This patch takes care of this.
Set the new timing on all dies implemented as suggested by Boris.
This was detected on the in-circuit ICnova-A20 SoM equipped with the
Micron MT29F32G08CBACAWP (4GiB) ONFI NAND device.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: fixup whitespace]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
* SPI NOR: a few new IDs / feature flags
* OMAP2 NAND: rename module so it doesn't conflict with onenand omap2.ko
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aXrv
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd
Pull more MTD updates from Brian Norris:
"There was one significant bug in my first pull request, fixed here. I
also threw in a few trivial ID additions and a small module rename.
Details:
- SPI NOR: bug fix for a "end of table" check that resulted in a NULL
dereference in some cases
- SPI NOR: a few new IDs / feature flags
- OMAP2 NAND: rename module so it doesn't conflict with onenand
omap2.ko"
* tag 'for-linus-20150909' of git://git.infradead.org/linux-mtd:
mtd: spi-nor: fix NULL dereference when no match found in spi_nor_ids[]
mtd: spi-nor: s25sl064p supports both dual and quad I/O
mtd: spi-nor: allow dual/quad reads on S25FL129P
mtd: nand: omap2: Rename shippable module to omap2_nand
mtd: spi-nor: Add support for sst25wf020a
mtd: spi-nor: Add support for Micron n25q064a serial flash
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
The driver supports board files specificating the flash
device, by passing a pxa3xx_nand_flash struct (with
flash parameters) in the platform data struct.
Currently this support is not being used by any board file.
Moreover, we'd like to deprecate such usage in favor of
using the device table in nand_ids.c.
So let's remove the ad-hoc flash specification.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As both omap2 onenand and omap2 nand driver modules are
named the same i.e. "omap2.ko", only one of them gets shipped
during MODPOST if both are configured as loadable modules.
To avoid this ambiguity let's ship the omap2 nand
driver as "omap2_nand.ko"
Reported by Pierre Neyron via github
https://github.com/beagleboard/linux/issues/40
Cc: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the full description of the Toshiba TC58NVG0S3E NAND chip in the
nand_ids table so that we can later use the NAND ECC info and ONFI timing
mode in controller drivers.
Tested with asm9260_nand driver. [Brian: driver still under review]
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read after
an erase.
The issue is that in the interrupt handler, the status bits are cleared
after the new command is issued. There is a small temporal window where
this happens :
- the previous command has set the command done bit
- the ready for a command bit is set
- the handler submits the next command
- just then, the command completes, and the command done bit is still
set
- the handler clears the "previous" command done bit
- the handler exits
In this flow, the "command done" of the next command will never trigger
a new interrupt to finish the status command, as it was cleared for both
commands.
Fix this by clearing the status bit before submitting a new command.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
The bug is tricky : if the bootloader left a status bit set, the
unmasking of interrupts does trigger the interrupt handler before the
first command is issued, blocking the good behavior of the nand.
The same would happen if in pxa3xx_nand code flow a status bit is left,
and then a command is started.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.
In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.
Fixes: 70ed85232a ("mtd: nand: pxa3xx: Introduce multiple page I/O
support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove extra space after the "platform:" prefix and make the alias matches
driver name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is better to have device name prefixed the actual error message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In recent kernels we have a lot of helper functions, including
devres API, to make life of device driver developer easy.
Convert the driver using devm_kzalloc() and pcim_enable_device().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Let's use module_pci_driver() macro to reduce code base of the driver.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to user to see the core part of the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
IFC IO accressor are set at run time based
on IFC IP registers endianness.IFC node in
DTS file contains information about
endianness.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Replaces the hard coded "always use EDO" policy with that prescribed
by the ONFI 3.1 specification that EDO mode should always be used if tRC
is below 30ns.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The TIMING_CFG register was previously statically set to a magic value
(extracted from Allwinner's BSP) when initializing the NAND controller.
Now that we have more details about the TIMING_CFG register layout
(extracted from the A83 user manual) we can dynamically calculate the
appropriate value for each NAND chip and set it when selecting the
chip.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
r852_ecc_correct() reads a 32-bit register into a 16-bit variable,
ecc_reg, but this variable is later used as if it was larger. This is
reported by clang when building the kernel with many warnings:
drivers/mtd/nand/r852.c:512:11: error: shift count >= width of type
[-Werror,-Wshift-count-overflow]
ecc_reg >>= 16;
^ ~~
Fix this by making ecc_reg 32-bit, like the return type of
r852_read_reg_dword().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.
[Brian: similar work submitted by Murali Karicheri <m-karicheri2@ti.com>
and Hao Zhang <hzhang@ti.com>]
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Do not call free_device() in init_nandsim, the caller - ns_init_module -
will take care of that if something goes wrong.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If allocating ns->nand_pages_slab fails, do not try to destroy it when
cleaning up nandsim resources.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() used in get_partition_name() does a dynamic
memory allocation and can fail. We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() does a dynamic memory allocation and can fail.
We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
device_create_file() can fail, therefore we have to
handle this case and abort.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is a Bad Idea (TM) to call mtd_device_register() or
mtd_device_parse_register() twice on the same master MTD. Among other
things, it makes partition overrides (e.g., cmdlinepart) much more
difficult.
Since commit 727dc612c4 ("mtd: part: Create the master device node
when partitioned"), we now have a config option that accomplishes the
same purpose as the double-registration done in diskonchip.c -- it
forces the master MTD to *always* be registered, while partitions may
optionally show up in addition. Eventually, we might like to make
CONFIG_MTD_PARTITIONED_MASTER into the default, but this could be
disruptive to user-space expectations of MTD numbering, so we'll take
that slowly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Alexander Shiyan <shc_work@mail.ru>
It's harmless to add 'ofpart' (the only different parser supported in
default mtdpart.c) to plat_nand. That let's us kill off one more custom
partition prober listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is an example of why it doesn't make much sense to put this
information here in the first place. I don't really know what purpose it
serves.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Hardware 8 bit ECC requires a different nand_ecclayout. Instead of adding yet
another static struct nand_ecclayout, generate it in code.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Copy to/from oob io area might not be aligned to 4 bytes. When 8 bit ECC is
used, the buffer size is 26. Add memcpy16_{to,from}io, and use them to avoid
truncating the buffer. Prefer memcpy32_{to,from}io when the buffer is properly
aligned for better performance.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For 4k pages the i.MX NFC hardware uses no more than 218 bytes for 8bit ECC
data. Larger oobsize confuses the logic of copy_spare(). Limit the size of used
oob size to avoid that.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To give people without the reference manual at hand a chance to
understand how spare area is handled in the i.MX nand controller,
improve commenting, naming of variables and coding style.
No functional change intended.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[baruch: declare oob_chunk_size; update comments; reword commit log]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove static in front of ctrl. This variable should not be shared
between different instances of brcmnand_probe(), it should be local to
this function and stored on the stack.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The caller already adds a new line and in the other cases there is no
new line added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are a few small hooks required for chips like BCM63138 and the
iProc family. Let's introduce those now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
BCM7xxx chips are supported entirely by the library code, since they use
generic irqchip interfaces and don't need any extra SoC-specific
configuration.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This core originated in Set-Top Box chips (BCM7xxx) but is used in a
variety of other Broadcom chips, including some BCM63xxx, BCM33xx, and
iProc/Cygnus. It's been used only on ARM and MIPS SoCs, so restrict it
to those architectures.
There are multiple revisions of this core throughout the years, and
almost every version broke register compatibility in some small way, but
with some effort, this driver is able to support v4.0, v5.0, v6.x, v7.0,
and v7.1. It's been tested on v5.0, v6.0, v6.1, v7.0, and v7.1 recently,
so there hopefully are no more lurking inconsistencies.
This patch adds just some library support, on which platform drivers can
be built.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation to enable ARCH_MMP on ARM64, a couple of fixes are needed
to build the pxa3xx_nand driver:
Legacy DMA will only used on ARM, so also make it condtional on
CONFIG_ARM.
__raw_{read,write}sl are not available on ARM64 or generically, so use
the readsl/writesl variants instead. Somewhat inconsistently,
{read,write}sl are inherently non-swapping with the generic version
using __raw_{read,write}l.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
[Brian: added one more __raw_readsl -> readsl]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that the driver handles the FIFO draining in a threaded interrupt, we can
base our timeout on jiffies and sleeping, instead of using mdelay.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
This not only should help readability but also handles corner cases
properly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
wait_for_completion_timeout does not return negative values so
result handling here does not need to check for negative return.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As all four bytes are written in any case the memset() is in vain.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This statement was written with a cast-to-loff_t to be sure to have a
full 64-bit mask. However, we don't account for the fact that
'1 << this->bbt_erase_shift' might already overflow.
This will not be a problem in practice, since eraseblocks should never
be anywhere near 4GiB. But we can do this for completeness, and quiet
Coverity in the meantime. CID #1226806.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Don't leak this->bbt, and return early if check_create() fails. It helps
to have a single error path to avoid these problems.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
