* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
drivers: mmc: msm_sdcc: Add EMBEDDED_SDIO support
mmc: msm_sdcc: Fix issue where clocks could be disabled mid transaction
mmc: msm_sdcc: Fix the dma exec function to use the proper delays
mmc: msm_sdcc: Don't set host->curr.mrq until after we're sure the busclk timer won't fire
mmc: msm_sdcc: Enable busclk idle timer for power savings
mmc: msm_sdcc: Don't disable interrupts while suspending
mmc: msm_sdcc: Fix issue where we might not end a sucessfull request
mmc: msm_sdcc: Featurize busclock power save and disable it by default
mmc: msm_sdcc: Fix bug where busclk expiry timer was not properly disabled
mmc: msm_sdcc: Reduce command timeouts and improve reliability.
mmc: msm_sdcc: Schedule clock disable after probe
mmc: msm_sdcc: Wrap readl/writel calls with appropriate clk delays
mmc: msm_sdcc: Driver clocking/irq improvements
msm: Add 'execute' datamover callback
mmc: msm_sdcc: Snoop SDIO_CCCR_ABORT register
mmc: msm_sdcc: Clean up clock management and add a 10us delay after enabling clocks
The MSM7x30 does not have a separate bank of memory for shared
memory communication with the radio CPU. Set the kernel base
address 2MB in, to use this first 2MB for this purpose.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
The MSM SOC's DMA controller contains several security domains.
On the MSM7x00, only security domain 3 is accessible to our CPU.
The 7x30, however, uses security domain 2. Fix up the register
definition macros to select this appropriately, based on
configured target.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Add a header describing the io regions for MSM7x30.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Support different RAM base addresses used by Qualcomm SOCs, with
QSD8x50 as the first addtional one.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Add a header describing the io regions for QSD8x50.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
GPIO support for Qualcomm SOCs requires interaction with the
radio (baseband processor). This API allows the different boards
to enable GPIO through the radio processor in a generic way.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
The 'PCOM' method of clock control (commands issued to the radio
CPU) is shared across several (but not all) Qualcomm SOCs.
Generalize this clock mechanism so these other SOCs can be added.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Scorpion-based SOCs from Qualcomm use a different interrupt
controller 'sirc'.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
msm_iomap.h is specific to the MSM7x00 series devices. Generalize
this in preparation to support more devices.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
irqs.h is specific to the MSM7x00 series devices. Generalize
this in preparation to support more devices.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Some smd clients may write from multiple threads, in which case it's
not safe to call smd_write without holding a lock. smd_write_atomic()
provides the same functionality as smd_write() but obtains the smd
lock first.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This code provides the low level interface to the "shared memory
state machine" (smsm), and the virtual serial channels (smd), used
to communicate with the baseband processor. Higher level transports
(rpc, ethernet, AT command channel, etc) ride on top of this.
Signed-off-by: Brian Swetland <swetland@google.com>
Keep track of the success/failure of the last vreg proc comm
command, and return that on debugfs reads.
Signed-off-by: Steve Muckle <smuckle@quicinc.com>
This adds acpuclock-arm11.c from Google. This provides control
over the cpu frequency for arm11 cpu's.
This has shared authorship between Google, and Qualcomm. Most
of it was written by Mike Chan at Google.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on a patch from Brent DeGraaf:
"The datamover supports channels which can be shared amongst devices.
As a result, the actual data transfer may occur some time after the
request is queued up. Some devices such as mmc host controllers
will timeout if a command is issued too far in advance of the actual
transfer, so if dma to other devices on the same channel is already
in progress or queued up, the added delay can cause pending transfers
to fail before they start. This change extends the api to allow a
user callback to be invoked just before the actual transfer takes
place, thus allowing actions directly associated with the dma
transfer, such as device commands, to be invoked with precise timing.
Without this mechanism, there is no way for a driver to realize
this timing. Also adds a user pointer to the command structure for use
by the caller to reference information that may be needed by the
callback routine for proper identification and processing associated
with that specific request. This change is necessary to fix problems
associated with excessive command timeouts and race conditions in the
mmc driver."
This patch also fixes all the callers of msm_dmov_enqueue_cmd() to
ensure their callback function is NULL.
Signed-off-by: San Mehat <san@google.com>
Cc: Brent DeGraaf <bdegraaf@quicinc.com>
Cc: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add missing include for msm_sdcc compilation, and remove pwrsink
support that is not mainline, yet.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[dwalker@codeaurora.org : fixed indent in mmc.h]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Provides options to select one of the three "lowspeed" UARTs
on MSM7k SoCs for DEBUG_LL output from the zImage decompressor
and kernel.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The baseband cpu owns the pmic, so voltage regulator control is only
available via a relatively limited interface through the proc_comm
transport.
Signed-off-by: Brian Swetland <swetland@google.com>
San:
- Propagate DM errors to the originator of the request.
- Implement msm_dmov_stop_cmd()
- Add return value to init code
- Modify msm_dmov_stop_cmd() to support ungraceful flushing
Arve:
- Disable datamover interrupt when not in use.
We turn off the interrrupt to allow power collapse from idle.
Signed-off-by: San Mehat <san@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
- Add some more peripherals (sdcc, etc) to the iomap.
- Remove virtual base addresses for devices that we should be passing
physical addresses to drivers via resources and ioremap()ing.
- don't try to use uarts for ll debug once the mmu is enabled due to
problems with the peripheral window
- make base addresses void __iomem * and fixup irq.c and timer.c
- Remove common.c and bring in devices.c/devices.h similar to
the PXA architecture.
Signed-off-by: Brian Swetland <swetland@google.com>
