Fix the port-lock initialisation regression introduced by commit
a3cb39d258 ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3 ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f743061a85 ("serial: core: Initialise spin lock before use in
uart_configure_port()") tried to work around a breakage introduced by
commit a3cb39d258 ("serial: core: Allow detach and attach serial
device for console") by adding a second initialisation of the port lock
when registering the port.
As reported by the build robots [1], this doesn't really solve the
regression introduced by the console-detach changes and also adds a
second redundant initialisation of the lock for normal ports.
Start cleaning up this mess by removing the redundant initialisation and
making sure that the port lock is again initialised once-only for ports
that aren't already in use as a console.
[1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian
Fixes: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c5cbc78acf ("tty: serial: qcom_geni_serial: Initialize baud
in qcom_geni_console_setup") fixed a bug by initting a variable that
was used in some cases without initialization. However, the "default"
baud rate picked by that CL was probably not the best choice. The
chances that anyone out there is trying to run a system with kernel
messages piped out over a 9600 baud serial port is just about nil.
Console messages are printed in a blocking manner. At 9600 baud we
print about 1 character per millisecond which means that printing a
40-byte message to the console will take ~40 ms. While it would
probably work, it's going to make boot _very_ slow and probably cause
the occasional timeout here and there in drivers (heck, even at 115200
console delays can wreck havoc).
This has already bit at least two people that I'm aware of that tried
to enable serial console by just adding "console=ttyMSM0" (instead of
"console=ttyMSM0,115200n8") to the command line, so it seems like it'd
be nice to fix.
Let's switch the default to 115200.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200911080054.1.I4c00b921c2f17b6988688046fa7be0f729f8d591@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use mmio32, we also need to set regshift.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 devices may modify iotype in their own earlycon setup. For example:
8250_mtk and 8250_uniphier force iotype to be MMIO32. Print earlycon info
after match->setup to reflect actual earlycon info.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200915054825.3289105-1-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates the following sparse warning:
drivers/tty/serial/ucc_uart.c:286:6: warning: symbol 'qe_uart_set_mctrl'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912033834.143166-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
SB1250 uart bug is related to PASS 2 workarounds. Use config
CONFIG_SB1_PASS_2_WORKAROUNDS directly and get rid of SIBYTE_1956_WAR.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This adds support for ACPI enumerated FSL 16550 UARTs.
For supporting ACPI, I added a wrapper so that this driver
can be used if firmware has exposed the HID "NXP0018" in
DSDT table.
This will be built as object file if config "SERIAL_8250_FSL"
is enabled which depends on config "SERIAL_8250_CONSOLE".
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac588759 ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some derivates of sc16is7xx devices expose more than one tty device to
userspace. If multiple such devices exist in a system, userspace
currently has no clean way to infer which tty maps to which physical
line.
Set the .iobase value to the relative index within the device to allow
infering the order through sysfs.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200901120329.4176302-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calculate "ucr1" UCR1_TRDYEN is duplicate.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200903062401.692442-1-yebin10@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI id for WCH384_8S 8 port PCI-E serial card.
because this card has so many ports, you may have
to check these two options before use it:
CONFIG_SERIAL_8250_RUNTIME_UARTS
CONFIG_SERIAL_8250_NR_UARTS
Signed-off-by: Du Huanpeng <u74147@gmail.com>
Link: https://lore.kernel.org/r/1598060848-27807-1-git-send-email-u74147@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label to put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/583003f385a103b4c089ce8144a215c58cfb117a.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the documentation (Documentation/filesystems/sysfs.rst),
snprintf() should not be used for formatting values returned by sysfs.
For all of the instances in serial_core.c, we know that the string will
be <PAGE_SIZE in length, so just use sprintf().
Issue identified by Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824223932.27709-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0Zl1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh0wCgicGyVAq3OUH9iTlgYqdkFHL1FWoAnAtP/jot
dB0yRgk2r+RvDL9Odb2u
=x5GL
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use platform_get_resource() to fetch the memory resource
instead of open-coded variant.
While here, fail the probe if no resource found or no port is added.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200804134807.11589-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-5-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-4-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-3-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work
even if UART isn't console") worked pretty well and I've been doing a
lot of debugging with it. However, recently I typed "dmesg" in kdb
and then held the space key down to scroll through the pagination. My
device hung. This was repeatable and I found that it was introduced
with the aforementioned commit.
It turns out that there are some strange boundary cases in geni where
in some weird situations it will signal RX_LAST but then will put 0 in
RX_LAST_BYTE. This means that the entire last FIFO entry is valid.
This weird corner case is handled in qcom_geni_serial_handle_rx()
where you can see that we only honor RX_LAST_BYTE if RX_LAST is set
_and_ RX_LAST_BYTE is non-zero. If either of these is not true we use
BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word.
Let's fix kgdb. While at it, also use the proper #define for 4.
Fixes: e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and
console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv30A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynW+gCgv+OqxT0jeNRAMSQcpMvP3wTBMKIAn1StfjJ4
y8uwZuQQimD49uj8XtDq
=bKSv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt
and console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues"
* tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
MAINTAINERS: enlist Greg formally for console stuff
vgacon: Fix for missing check in scrollback handling
Revert "serial: 8250: Let serial core initialise spin lock"
serial: 8250: Let serial core initialise spin lock
tty: keyboard, do not speculate on func_table index
serial: stm32: Add RS485 RTS GPIO control
serial: 8250_dw: Fix common clocks usage race condition
serial: 8250_dw: Pass the same rate to the clk round and set rate methods
serial: 8250_dw: Simplify the ref clock rate setting procedure
serial: 8250: Add 8250 port clock update method
tty: serial: imx: add imx earlycon driver
tty: serial: imx: enable imx serial console port as module
tty/synclink: remove leftover bits of non-PCI card support
tty: Use the preferred form for passing the size of a structure type
tty: Fix identation issues in struct serial_struct32
tty: Avoid the use of one-element arrays
serial: msm_serial: add sparse context annotation
serial: pmac_zilog: add sparse context annotation
newport_con: vc_color is now in state
serial: imx: use hrtimers for rs485 delays
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
-----BEGIN PGP SIGNATURE-----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=ZcMq
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Herbert Xu made printk header file self-contained.
- Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
error handling.
- Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
code.
- Minor documentation updates.
* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
lib/vsprintf: Force type of flags value for gfp_t
lib/vsprintf: Replace custom spec to print decimals with generic one
lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
printk: Make linux/printk.h self-contained
doc:kmsg: explicitly state the return value in case of SEEK_CUR
Replace HTTP links with HTTPS ones: vsprintf
hvc: unify console setup naming
console: Fix trivia typo 'change' -> 'chance'
console: Propagate error code from console ->setup()
tty: hvc: Return proper error code from console ->setup() hook
serial: sunzilog: Return proper error code from console ->setup() hook
serial: sunsab: Return proper error code from console ->setup() hook
mips: Return proper error code from console ->setup() hook
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
This reverts commit 679193b7ba.
It appears that in QEmu the lock has been initialised differently
(it wasn't obvious on real hardware during testing). Let's
revert the change until the better approach will be developed.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the serial core handles spin lock initialisation,
let the driver rely on it.
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indeed according to the clk API if clk_round_rate() has successfully
accepted a rate, then in order setup the clock with value returned by the
clk_round_rate() the clk_set_rate() method must be called with the
original rate value.
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Really instead of twice checking the clk_round_rate() return value
we could do it once, and if it isn't error the clock rate can be changed.
By doing so we decrease a number of ret-value tests and remove a weird
goto-based construction implemented in the dw8250_set_termios() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split imx earlycon driver from imx serial driver "imx.c" as
separated driver. imx serial driver can be built as module,
but earlycon driver only support build in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-3-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for building i.MX serial driver as module.
The changes of the patch:
- imx console driver can be built as module.
- move out earlycon code to separated driver like imx_earlycon.c,
and imx earlycon driver only support build-in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8d8h4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGd0sH/2iktYhMwPxzzpnb
eI3OuTX/mRn4vUFOfpx9dmGVleMfKkpbvnn3IY7wA62Qfv7J7lkFRa1Bd1DlqXfW
yyGTGDSKG5chiRCOU3s9ni92M4xIzFlrojyt/dIK2lUGMzUPI9FGlZRGQLKqqwLh
2syOXRWbcQ7e52IHtDSy3YBNveKRsP4NyqV+GxGiex18SMB/M3Pw9EMH614eDPsE
QAGQi5uGv4hPJtFHgXgUyBPLFHIyFAiVxhFRIj7u2DSEKY79+wO1CGWFiFvdTY4B
CbqKXLffY3iQdFsLJkj9Dl8cnOQnoY44V0EBzhhORxeOp71StUVaRwQMFa5tp48G
171s5Hs=
=BQIl
-----END PGP SIGNATURE-----
Merge 5.8-rc7 into tty-next
we need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sparse context annotation to the receive handlers, which release and
reacquire the port lock, to silence sparse warnings:
drivers/tty/serial/msm_serial.c:748:25: warning: context imbalance in 'msm_handle_rx_dm' - unexpected unlock
drivers/tty/serial/msm_serial.c:814:28: warning: context imbalance in 'msm_handle_rx' - unexpected unlock
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sparse context annotation to the receive handler, which releases and
reacquires the port lock, to silence a sparse warning:
drivers/tty/serial/pmac_zilog.c:255:36: sparse: sparse: context imbalance in 'pmz_receive_chars' - unexpected unlock
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200723123327.5843-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250
port") fixed limits of a baud rate setting for a generic 8250 port.
In other words since that commit the baud rate has been permitted to be
within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely
normal for a standard 8250 UART port. But there are custom 8250 ports,
which provide extended baud rate limits. In particular the Mediatek 8250
port can work with baud rates up to "uartclk" speed.
Normally that and any other peculiarity is supposed to be handled in a
custom set_termios() callback implemented in the vendor-specific
8250-port glue-driver. Currently that is how it's done for the most of
the vendor-specific 8250 ports, but for some reason for Mediatek a
solution has been spread out to both the glue-driver and to the generic
8250-port code. Due to that a bug has been introduced, which permitted the
extended baud rate limit for all even for standard 8250-ports. The bug
has been fixed by the commit 7b668c064e ("serial: 8250: Fix max baud
limit in generic 8250 port") by narrowing the baud rates limit back down to
the normal bounds. Unfortunately by doing so we also broke the
Mediatek-specific extended bauds feature.
A fix of the problem described above is twofold. First since we can't get
back the extended baud rate limits feature to the generic set_termios()
function and that method supports only a standard baud rates range, the
requested baud rate must be locally stored before calling it and then
restored back to the new termios structure after the generic set_termios()
finished its magic business. By doing so we still use the
serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers,
while the extended baud rate setting procedure will be performed later in
the custom Mediatek-specific set_termios() callback. Second since a true
baud rate is now fully calculated in the custom set_termios() method we
need to locally update the port timeout by calling the
uart_update_timeout() function. After the fixes described above are
implemented in the 8250_mtk.c driver, the Mediatek 8250-port should
get back to normally working with extended baud rates.
Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com
Fixes: 7b668c064e ("serial: 8250: Fix max baud limit in generic 8250 port")
Reported-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: stable <stable@vger.kernel.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch imitates 6e0a5de213 ("serial: 8250: Use hrtimers for
rs485 delays") in replacing the previously used classic timers
with hrtimers. The old way provided a too coarse resolution on
systems with configs of less than 1000 HZ.
Use of hrtimers addresses this and can be easily extended to
support microsecond resolution in future when support
for this arrives upstream.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200714093012.21621-3-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for delays between assertion of RTS (which is supposed
to enable the rs485 transmitter) and sending as well as between the last
send char and deassertionof RTS.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200714093012.21621-2-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct tty_port is part of the uart state and will never be NULL in
the receive helpers. Drop the bogus NULL checks and rename the
pointer-variables "port" to differentiate them from struct tty_struct
pointers (which can be NULL).
Fixes: 962963e4ee ("serial: tegra: Switch to using struct tty_port")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33ae787b74 ("serial: tegra: add support to ignore read") added
support for dropping input in case CREAD isn't set, but for PIO the
ignore_status_mask wasn't checked until after the character had been
put in the receive buffer.
Note that the NULL tty-port test is bogus and will be removed by a
follow-on patch.
Fixes: 33ae787b74 ("serial: tegra: add support to ignore read")
Cc: stable <stable@vger.kernel.org> # 5.4
Cc: Shardar Shariff Md <smohammed@nvidia.com>
Cc: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200710135947.2737-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable_device() and pci_set_power_state()
to do required operations. In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Link: https://lore.kernel.org/r/20200720120414.399961-1-vaibhavgupta40@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20200718103018.3164-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following checkpatch error and warning:
1. space required after ','
2. Missing a blank line after declarations
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Link: https://lore.kernel.org/r/20200716115438.9967-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718100807.983-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718123840.19957-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f38278e9b8.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: f38278e9b8 ("serial: sh-sci: Initialize spinlock for uart console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8f065acec7.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 8f065acec7 ("serial: imx: Initialize lock for non-registered console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 17b4efdf4e.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 17b4efdf4e ("tty: serial: add missing spin_lock_init for SiFive serial console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8508f4cba3.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 8508f4cba3 ("serial: amba-pl011: Make sure we initialize the port.lock spinlock")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0f87aa66e8.
There has been a quick fix against uninitialised lock revealed by
the commit f743061a85 ("serial: core: Initialise spin lock before use
in uart_configure_port()"). Since we have now better fix in serial core,
this may be safely reverted.
Fixes: 0f87aa66e8 ("serial: sunhv: Initialize lock for non-registered console")
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200711135346.71171-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problems started with the revert (18cc7ac8a2). The
cdns_uart_console.index is statically assigned -1. When the port is
registered, Linux assigns consecutive numbers to it. It turned out that
when using ttyPS1 as console, the index is not updated as we are reusing
the same cdns_uart_console instance for multiple ports. When registering
ttyPS0, it gets updated from -1 to 0, but when registering ttyPS1, it
already is 0 and not updated.
That led to 2ae11c46d5. It assigns the index prior to registering
the uart_driver once. Unfortunately, that ended up breaking the
situation where the probe order does not match the id order. When using
the same device tree for both uboot and linux, it is important that the
serial0 alias points to the console. So some boards reverse those
aliases. This was reported by Jan Kiszka. The proposed fix was reverting
the index assignment and going back to the previous iteration.
However such a reversed assignement (serial0 -> uart1, serial1 -> uart0)
was already partially broken by the revert (18cc7ac8a2). While the
ttyPS device works, the kmsg connection is already broken and kernel
messages go missing. Reverting the id assignment does not fix this.
>From the xilinx_uartps driver pov (after reverting the refactoring
commits), there can be only one console. This manifests in static
variables console_pprt and cdns_uart_console. These variables are not
properly linked and can go out of sync. The cdns_uart_console.index is
important for uart_add_one_port. We call that function for each port -
one of which hopefully is the console. If it isn't, the CON_ENABLED flag
is not set and console_port is cleared. The next cdns_uart_probe call
then tries to register the next port using that same cdns_uart_console.
It is important that console_port and cdns_uart_console (and its index
in particular) stay in sync. The index assignment implemented by
Shubhrajyoti Datta is correct in principle. It just may have to happen a
second time if the first cdns_uart_probe call didn't encounter the
console device. And we shouldn't change the index once the console uart
is registered.
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Link: https://lore.kernel.org/linux-serial/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com/
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Fixes: 76ed2e1057 ("Revert "tty: xilinx_uartps: Fix missing id assignment to the console"")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200713073227.GA3805@laureti-dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into tty-next
We need the serial/tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes that
went into 5.8-rc1 but turned out to cause a noticable overhead and cpu
usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on many
serial driver consoles.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXxBx8g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykqAwCeIWhRt4Z6YdUXjT/rFycYlFKWCVsAoJodlx6C
7FoXKFoP4c72il+qgHMp
=cCbW
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial driver fixes from Greg KH:
:Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes
that went into 5.8-rc1 but turned out to cause a noticable overhead
and cpu usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on
many serial driver consoles.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: core: Initialise spin lock before use in uart_configure_port()
serial: mxs-auart: add missed iounmap() in probe failure and remove
serial: sh-sci: Initialize spinlock for uart console
Revert "tty: xilinx_uartps: Fix missing id assignment to the console"
serial: core: drop redundant sysrq checks
serial: core: fix sysrq overhead regression
Revert "serial: core: Refactor uart_unlock_and_check_sysrq()"
tty/serial: fix serial_core.c kernel-doc warnings
tty: serial: cpm_uart: Fix behaviour for non existing GPIOs
When using the geni-serial as console, its important to be
able to hit the lowest possible power state in suspend,
even with no_console_suspend.
The only thing that prevents it today on platforms like the sc7180
is the interconnect BW votes, which we certainly don't need when
the system is in suspend. So in the suspend handler mark them as
ACTIVE_ONLY (0x3) and on resume switch them back to the ALWAYS tag (0x7)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1594704709-26072-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The geni serial driver had a rule that we'd only use 1 byte per FIFO
word for the TX FIFO if we were being used for the serial console.
This is ugly and a bit of a pain. It's not too hard to fix, so fix
it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626125844.2.Iabd56347670b9e4e916422773aba5b27943d19ee@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The geni serial driver had the rather sketchy hack in it where it
would adjust the number of bytes per RX FIFO word from 4 down to 1 if
it detected that CONFIG_CONSOLE_POLL was enabled (for kgdb) and this
was a console port (defined by the kernel directing output to this
port via the "console=" command line argument).
The problem with that sketchy hack is that it's possible to run kgdb
over a serial port even if it isn't used for console.
Let's avoid the hack by simply handling the 4-bytes-per-FIFO word case
for kdb. We'll have to have a (very small) cache but that should be
fine.
A nice side effect of this patch is that an agetty (or similar)
running on this port is less likely to drop characters. We'll
have roughly 4 times the RX FIFO depth than we used to now.
NOTE: the character cache here isn't shared between the polling API
and the non-polling API. That means that, technically, the polling
API could eat a few extra bytes. This doesn't seem to pose a huge
problem in reality because we'll only get several characters per FIFO
word if those characters are all received at nearly the same time and
we don't really expect non-kgdb characters to be sent to the same port
as kgdb at the exact same time we're exiting kgdb.
ALSO NOTE: we still have the sketchy hack for setting the number of
bytes per TX FIFO word in place, but that one is less bad. kgdb
doesn't have any problem with this because it always just sends 1 byte
at a time and waits for it to finish. The TX FIFO hack is only really
needed for console output. In any case, a future patch will remove
that hack, too.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200626125844.1.I8546ecb6c5beb054f70c5302d1a7293484212cd1@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The comment near to uart_port_spin_lock_init() says:
Ensure that the serial console lock is initialised early.
If this port is a console, then the spinlock is already initialised.
and there is nothing about enabled or disabled consoles. The commit
a3cb39d258 ("serial: core: Allow detach and attach serial device
for console") made a change, which follows the comment, and also to
prevent reinitialisation of the lock in use, when user detaches and
attaches back the same console device. But this change discovers
another issue, that uart_add_one_port() tries to access a spin lock
that now may be uninitialised. This happens when a driver expects
the serial core to register a console on its behalf. In this case
we must initialise a spin lock before use.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Marc Zyngier <maz@kernel.org>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20200706214903.56148-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver calls ioremap() in probe, but it misses calling iounmap() in
probe's error handler and remove.
Add the missed calls to fix it.
Fixes: 47d37d6f94 ("serial: Add auart driver for i.MX23/28")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200709135608.68290-1-hslester96@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of generic DT binding for annoucing RTS/CTS lines. The initial
binding 'st,hw-flow-control' is not needed anymore since generic binding
is available, but is kept for backward compatibility.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200520133932.30441-3-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ae11c46d5.
It turned out to break the ultra96-rev1, e.g., which uses uart1 as
serial0 (and stdout-path = "serial0:115200n8").
Fixes: 2ae11c46d5 ("tty: xilinx_uartps: Fix missing id assignment to the console")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f4092727-d8f5-5f91-2c9f-76643aace993@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e20fc3917 ("serial_core: Move sysrq functions from header
file") converted the inline sysrq helpers to exported functions which
are now called for every received character, interrupt and break signal
also on systems without CONFIG_MAGIC_SYSRQ_SERIAL instead of being
optimised away by the compiler.
Inlining these helpers again also avoids the function call overhead when
CONFIG_MAGIC_SYSRQ_SERIAL is enabled (e.g. when the port is not used as
a console).
Fixes: 8e20fc3917 ("serial_core: Move sysrq functions from header file")
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200610152232.16925-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit da9a5aa340.
In order to ease backporting a fix for a sysrq regression, revert this
rewrite which was since added on top.
The other sysrq helpers now bail out early when sysrq is not enabled;
it's better to keep that pattern here as well.
Note that the __releases() attribute won't be needed after the follow-on
fix either.
Fixes: da9a5aa340 ("serial: core: Refactor uart_unlock_and_check_sysrq()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200610152232.16925-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200618122952.88265-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618123320.88612-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122744.88204-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618122024.87170-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() provides an established error code and error message.
Also, it's better to use dedicated API to retrieve Linux IRQ resource.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200618095144.73852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a4912303ac ("serial: kgdboc: Allow earlycon initialization
to be deferred") it looks like Daniel really took Linus's new
suggestion about not needing to wrap at 80 columns to heart and he
jammed two full lines of comments into one line. Either that or he
just somehow accidentally deleted a carriage return when doing final
edits on the patch. In either case let's make it look prettier.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200602124044.1.Iee31247bc080d42a02e167454b1225a1b4283705@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since dev_err() calls can lead to synchronous writes to another serial
console these calls can provide significant latency during irq-handling
in tegra_uart_isr(). With this latency another interrupt is likely to
apper during handling of the first interrupt, which might lock up the
kernel completely.
These errors are reported to the error counters so converting the
dev_err() to dev_dbg() is appropriate.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Link: https://lore.kernel.org/r/20200605145714.9964-1-gaireg@gaireg.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_num_ports returns -ENODEV, and the result is stored in int, so it
should not be unsigned. Zero ports does not seem to make sense, so
make that check consistent.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Link: https://lore.kernel.org/r/20200606151146.GA10940@amd
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the recently added gpio include from the serial-core header in
favour of a forward declaration and instead include the gpio header only
where needed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200610155121.14014-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The formula for the baud rate is
baud rate = "baud clock / ((OSR+1) × SBR)
Algorithm used in function lpuart32_serial_setbrg() only changes
the SBR. Even with maxmum value put in, OSR stays at 0x7 and the
lowest baud rate would be ~ 2600 bps
Update the algorithm to allow driver operation at 1200,2400 or 600 bps
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Link: https://lore.kernel.org/r/1593170434-13524-1-git-send-email-vabhav.sharma@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARRAY_SIZE() is the number of elements but we want the number of
bytes so sizeof() is more appropriate. Fortunately, it's the same
thing here because this is an array of u8 so this doesn't change
runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200624132744.GD9972@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_gpiod_get_index() doesn't return NULL but -ENOENT when the
requested GPIO doesn't exist, leading to the following messages:
[ 2.742468] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.748147] can't set direction for gpio #2: -2
[ 2.753081] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.758724] can't set direction for gpio #3: -2
[ 2.763666] gpiod_direction_output: invalid GPIO (errorpointer)
[ 2.769394] can't set direction for gpio #4: -2
[ 2.774341] gpiod_direction_input: invalid GPIO (errorpointer)
[ 2.779981] can't set direction for gpio #5: -2
[ 2.784545] ff000a20.serial: ttyCPM1 at MMIO 0xfff00a20 (irq = 39, base_baud = 8250000) is a CPM UART
Use devm_gpiod_get_index_optional() instead.
At the same time, handle the error case and properly exit
with an error.
Fixes: 97cbaf2c82 ("tty: serial: cpm_uart: Convert to use GPIO descriptors")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/694a25fdce548c5ee8b060ef6a4b02746b8f25c0.1591986307.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a comment. Fix it.
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20200617105907.7143-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code slightly more readable by removing unneeded line breaks,
adding missing line breaks and white spaces. This also fixes few strict
checkpatch suggestions:
CHECK: spaces preferred around that '-' (ctx:VxV)
CHECK: Unbalanced braces around else statement
CHECK: Lines should not end with a '('
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200617152856.18086-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kgdb context, calling console handlers aren't safe due to locks used
in those handlers which could in turn lead to a deadlock. Although, using
oops_in_progress increases the chance to bypass locks in most console
handlers but it might not be sufficient enough in case a console uses
more locks (VT/TTY is good example).
Currently when a driver provides both polling I/O and a console then kdb
will output using the console. We can increase robustness by using the
currently active polling I/O driver (which should be lockless) instead
of the corresponding console. For several common cases (e.g. an
embedded system with a single serial port that is used both for console
output and debugger I/O) this will result in no console handler being
used.
In order to achieve this we need to reverse the order of preference to
use dbg_io_ops (uses polling I/O mode) over console APIs. So we just
store "struct console" that represents debugger I/O in dbg_io_ops and
while emitting kdb messages, skip console that matches dbg_io_ops
console in order to avoid duplicate messages. After this change,
"is_console" param becomes redundant and hence removed.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1591264879-25920-5-git-send-email-sumit.garg@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-4-andriy.shevchenko@linux.intel.com
For unifying console ->setup() handling, which is poorly documented,
return error code, rather than non-zero arbitrary number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20200618164751.56828-3-andriy.shevchenko@linux.intel.com
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1592222564-13556-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Get the interconnect paths for Uart based Serial Engine device
and vote according to the baud rate requirement of the driver.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1592908737-7068-5-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
Note, you will get a conflict merging with your tree in the
Documentation/devicetree/bindings/serial/rs485.yaml file, but it should
be pretty obvious what to do. If not, I'm sure Rob will clean it all up
afterwards :)
All of these have been in linux-next with no issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzpCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRxACgjGtOKPjahONL4lWd0F8ZYEcyw7sAn34woBCO
BDUV3kolrRQ4OYNJWsHP
=TvqG
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
By far the biggest change in this cycle are the changes that allow much
earlier debug of systems that are hooked up via UART by taking advantage
of the earlycon framework to implement the kgdb I/O hooks before handing
over to the regular polling I/O drivers once they are available. When
discussing Doug's work we also found and fixed an broken
raw_smp_processor_id() sequence in in_dbg_master().
Also included are a collection of much smaller fixes and tweaks: a
couple of tweaks to ged rid of doc gen or coccicheck warnings, future
proof some internal calculations that made implicit power-of-2
assumptions and eliminate some rather weird handling of magic
environment variables in kdb.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=uLAB
-----END PGP SIGNATURE-----
Merge tag 'kgdb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"By far the biggest change in this cycle are the changes that allow
much earlier debug of systems that are hooked up via UART by taking
advantage of the earlycon framework to implement the kgdb I/O hooks
before handing over to the regular polling I/O drivers once they are
available. When discussing Doug's work we also found and fixed an
broken raw_smp_processor_id() sequence in in_dbg_master().
Also included are a collection of much smaller fixes and tweaks: a
couple of tweaks to ged rid of doc gen or coccicheck warnings, future
proof some internal calculations that made implicit power-of-2
assumptions and eliminate some rather weird handling of magic
environment variables in kdb"
* tag 'kgdb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kdb: Remove the misfeature 'KDBFLAGS'
kdb: Cleanup math with KDB_CMD_HISTORY_COUNT
serial: amba-pl011: Support kgdboc_earlycon
serial: 8250_early: Support kgdboc_earlycon
serial: qcom_geni_serial: Support kgdboc_earlycon
serial: kgdboc: Allow earlycon initialization to be deferred
Documentation: kgdboc: Document new kgdboc_earlycon parameter
kgdb: Don't call the deinit under spinlock
kgdboc: Disable all the early code when kgdboc is a module
kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles
kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc
kgdb: Prevent infinite recursive entries to the debugger
kgdb: Delay "kgdbwait" to dbg_late_init() by default
kgdboc: Use a platform device to handle tty drivers showing up late
Revert "kgdboc: disable the console lock when in kgdb"
kgdb: Disable WARN_CONSOLE_UNLOCKED for all kgdb
kgdb: Return true in kgdb_nmi_poll_knock()
kgdb: Drop malformed kernel doc comment
kgdb: Fix spurious true from in_dbg_master()
Implement the read() function in the early console driver. With
recently added kgdboc_earlycon feature, this allows you to use kgdb
to debug fairly early into the system boot.
We only bother implementing this if polling is enabled since kgdb can't
be enabled without that.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.12.I8ee0811f0e0816dd8bfe7f2f5540b3dba074fae8@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Implement the read() function in the early console driver. With
recent kgdb patches this allows you to use kgdb to debug fairly early
into the system boot.
We only bother implementing this if polling is enabled since kgdb
can't be enabled without that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.11.I8f668556c244776523320a95b09373a86eda11b7@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Implement the read() function in the early console driver. With
recent kgdb patches this allows you to use kgdb to debug fairly early
into the system boot.
We only bother implementing this if polling is enabled since kgdb
can't be enabled without that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200507130644.v4.10.If2deff9679a62c1ce1b8f2558a8635dc837adf8c@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Currently there is no guarantee that an earlycon will be initialized
before kgdboc tries to adopt it. Almost the opposite: on systems
with ACPI then if earlycon has no arguments then it is guaranteed that
earlycon will not be initialized.
This patch mitigates the problem by giving kgdboc_earlycon a second
chance during console_init(). This isn't quite as good as stopping during
early parameter parsing but it is still early in the kernel boot.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200430161741.1832050-1-daniel.thompson@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
When kgdboc is compiled as a module all of the "ekgdboc" and
"kgdb_earlycon" code isn't useful and, in fact, breaks compilation.
This is because early_param() isn't defined for modules and that's how
this code gets configured.
It turns out that this was broken by commit eae3e19ca9 ("kgdboc:
Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc") and then
made worse by commit 220995622d ("kgdboc: Add kgdboc_earlycon to
support early kgdb using boot consoles"). I guess the #ifdef wasn't
so useless, even if it wasn't obvious why it was useful. When kgdboc
was compiled as a module only "CONFIG_KGDB_SERIAL_CONSOLE_MODULE" was
defined, not "CONFIG_KGDB_SERIAL_CONSOLE". That meant that the old
module.
Let's basically do the same thing that the old code (pre-removal of
the #ifdef) did but use "IS_BUILTIN(CONFIG_KGDB_SERIAL_CONSOLE)" to
make it more obvious what the point of the check is. We'll fix
kgdboc_earlycon in a similar way.
Fixes: 220995622d ("kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles")
Fixes: eae3e19ca9 ("kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200519084345.1.I91670accc8a5ddabab227eb63bb4ad3e2e9d2b58@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
To support BT use case over UART at baud rate of 3.2 Mbps,
we need SE clocks to run at 51.2MHz frequency. Previously this
frequency was not available in clk src, so, we were requesting
for 102.4 MHz and dividing it internally by 2 to get 51.2MHz.
As now 51.2MHz frequency is made available in clk src,
adding this frequency to UART frequency table.
We will save significant amount of power, if 51.2 is used
because it belongs to LowSVS range whereas 102.4 fall into
Nominal category.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1590747282-5487-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AGTIM flag must be cleared explicitly, otherwise the IRQ handler
will be called in an endless loop.
Fortunately, this issue currently doesn't affect mainline kernels in
practice, as the the RX FIFO trigger level is set to 1 in UFCR. When
setting the trigger level to a higher number, the issue is trivially
reproducible by any RX without DMA that doesn't fill the FIFO up to the
configured level.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200528154747.14201-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81966 is a LPC/eSPI to 6 UARTs SuperIO. It has fully compatible
with F81866. It's also need check the IRQ mode with system assigned.
F81966 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Link: https://lore.kernel.org/r/20200528022429.32078-1-hpeter+linux_kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series of uart controllers is able to work in IrDA mode.
Add per-port flag to the device-tree to enable that feature if needed.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200529055058.1606910-3-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8759ad17d ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree: Amend the serial
core to retrieve the GPIO from the device tree (or ACPI table) and amend
the default ->rs485_config() callback for 8250 drivers to change the
GPIO on request from user space.
Perhaps 8250_exar.c can be converted to the generic approach in a
follow-up patch.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/94c6c800d1ca9fa04766dd1d43a8272c5ad4bedd.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parameter is named p while the documentation talks about up.
Fix the doc to be in line with the code.
Fixes: 058bc104f7 ("serial: 8250: Generalize rs485 software emulation")
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200517215610.2131618-2-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some embedded devices still use these serial ports; make sure they're
still enabled by default on architectures more likely to have them, to
avoid rendering someone's console unavailable.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes: dc56ecb81a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/a20b5fb7dd295cfb48160eecf4bdebd76332d67d.1590509426.git.josh@joshtriplett.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Freescale IMX console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200525105952.13744-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the driver probes just fine and binds all its resources even
if the physical device is not present.
As the device lacks an identification register, let's at least read the
LSR register to check whether a device at the configured address responds
to the request at all.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-7-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the interrupt line is shared with other devices, the IRQ must be
level-triggered, as only one device can trigger a falling edge. To support
this, try to acquire the IRQ with IRQF_TRIGGER_LOW|IRQF_SHARED first.
Interrupt controllers that lack support for level-triggers will return an
error, in which case the driver will now retry the acqusition with
IRQF_TRIGGER_FALLING, which was also the default before.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-6-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a threaded IRQ handler to get rid of the irq_work kthread.
This also allows for the driver to use interrupts generated by
a threaded controller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-5-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently only uses IRQF_TRIGGER_FALLING if the probing
happened without a device-tree setup. The device however will always
generate falling edges on its IRQ line, so let's use that flag in
all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-4-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to display console messages in low power mode, console pins
must be kept active after suspend call.
Initial patch "serial: stm32: add support for no_console_suspend" was part
of "STM32 usart power improvement" series, but as dependancy to
console_suspend pinctl state has been removed to fit with Rob comment [1],
this patch has no more dependancy with any other patch of this series.
[1] https://lkml.org/lkml/2019/7/9/451
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200519094104.27082-1-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable kgdb to debug the early parts of the kernel.
Unfortunately kgdb normally is a client of the tty API in the kernel
and serial drivers don't register to the tty layer until fairly late
in the boot process.
Serial drivers do, however, commonly register a boot console. Let's
enable the kgdboc driver to work with boot consoles to provide early
debugging.
This change co-opts the existing read() function pointer that's part
of "struct console". It's assumed that if a boot console (with the
flag CON_BOOT) has implemented read() that both the read() and write()
function are polling functions. That means they work without
interrupts and read() will return immediately (with 0 bytes read) if
there's nothing to read. This should be a safe assumption since it
appears that no current boot consoles implement read() right now and
there seems no reason to do so unless they wanted to support
"kgdboc_earlycon".
The normal/expected way to make all this work is to use
"kgdboc_earlycon" and "kgdboc" together. You should point them both
to the same physical serial connection. At boot time, as the system
transitions from the boot console to the normal console (and registers
a tty), kgdb will switch over.
One awkward part of all this, though, is that there can be a window
where the boot console goes away and we can't quite transtion over to
the main kgdboc that uses the tty layer. There are two main problems:
1. The act of registering the tty doesn't cause any call into kgdboc
so there is a window of time when the tty is there but kgdboc's
init code hasn't been called so we can't transition to it.
2. On some serial drivers the normal console inits (and replaces the
boot console) quite early in the system. Presumably these drivers
were coded up before earlycon worked as well as it does today and
probably they don't need to do this anymore, but it causes us
problems nontheless.
Problem #1 is not too big of a deal somewhat due to the luck of probe
ordering. kgdboc is last in the tty/serial/Makefile so its probe gets
right after all other tty devices. It's not fun to rely on this, but
it does work for the most part.
Problem #2 is a big deal, but only for some serial drivers. Other
serial drivers end up registering the console (which gets rid of the
boot console) and tty at nearly the same time.
The way we'll deal with the window when the system has stopped using
the boot console and the time when we're setup using the tty is to
keep using the boot console. This may sound surprising, but it has
been found to work well in practice. If it doesn't work, it shouldn't
be too hard for a given serial driver to make it keep working.
Specifically, it's expected that the read()/write() function provided
in the boot console should be the same (or nearly the same) as the
normal kgdb polling functions. That means continuing to use them
should work just fine. To make things even more likely to work work
we'll also trap the recently added exit() function in the boot console
we're using and delay any calls to it until we're all done with the
boot console.
NOTE: there could be ways to use all this in weird / unexpected ways.
If you do something like this, it's a bit of a buyer beware situation.
Specifically:
- If you specify only "kgdboc_earlycon" but not "kgdboc" then
(depending on your serial driver) things will probably work OK, but
you'll get a warning printed the first time you use kgdb after the
boot console is gone. You'd only be able to do this, of course, if
the serial driver you're running atop provided an early boot console.
- If your "kgdboc_earlycon" and "kgdboc" devices are not the same
device things should work OK, but it'll be your job to switch over
which device you're monitoring (including figuring out how to switch
over gdb in-flight if you're using it).
When trying to enable "kgdboc_earlycon" it should be noted that the
names that are registered through the boot console layer and the tty
layer are not the same for the same port. For example when debugging
on one board I'd need to pass "kgdboc_earlycon=qcom_geni
kgdboc=ttyMSM0" to enable things properly. Since digging up the boot
console name is a pain and there will rarely be more than one boot
console enabled, you can provide the "kgdboc_earlycon" parameter
without specifying the name of the boot console. In this case we'll
just pick the first boot that implements read() that we find.
This new "kgdboc_earlycon" parameter should be contrasted to the
existing "ekgdboc" parameter. While both provide a way to debug very
early, the usage and mechanisms are quite different. Specifically
"kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and
there is a transition from one to the other. The "ekgdboc" parameter,
on the other hand, replaces the "kgdboc" parameter. It runs the same
logic as the "kgdboc" parameter but just relies on your TTY driver
being present super early. The only known usage of the old "ekgdboc"
parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should
be noted that "kbd" has special treatment allowing it to init early as
a tty device.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This file is only ever compiled if that config is on since the
Makefile says:
obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
Let's get rid of the useless #ifdef.
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.7.Icb528f03d0026d957e60f537aa711ada6fd219dc@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This reverts commit 81eaadcae8.
Commit 81eaadcae8 ("kgdboc: disable the console lock when in kgdb")
is no longer needed now that we have the patch ("kgdb: Disable
WARN_CONSOLE_UNLOCKED for all kgdb"). Revert it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.2.I02258eee1497e55bcbe8dc477de90369c7c7c2c5@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace contents of EXAR_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512140252.67631-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXrVmRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymY+ACfelBeBAxlYjuvZ8QpDYSkR9fl8EIAoKeuJocX
TaXtUFCvCSax68siL81w
=L0Rp
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues"
* tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xilinx_uartps: Fix missing id assignment to the console
vt: fix unicode console freeing with a common interface
Revert "tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart"
Support 32-bit access for the TX/RX hold registers UTXH and URXH.
This is required for some newer SoCs.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-3-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the name of macro for general usage.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-1-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9231e698
Rajendra writes:
Greg, there are other patches in the series which have a
dependency on this patch [1] would it be possible for you to
drop this patch and instead ack it so it can be taken via the
msm tree?
So dropping it from here.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1588507469-31889-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 580d952e44 ("tty:
serial: bcm63xx: fix missing clk_put() in bcm63xx_uart") because we
should not be doing a clk_put() if we were not successful in getting a
valid clock reference via clk_get() in the first place.
Fixes: 580d952e44 ("tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200501013904.1394-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains a handful of fixes that I'd like to target for 5.7.
Specifically:
* The change of a linker argument to allow linking with lld.
* A build fix for configurations without a frame pointer.
* A handful of build fixes related the SBI 0.1 vs 0.2 split.
* The removal of STRICT_KERNEL_RWX for !MMU, which isn't useful
-----BEGIN PGP SIGNATURE-----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=MtxP
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes.
Specifically:
- fix linker argument to allow linking with lld
- build fix for configurations without a frame pointer
- a handful of build fixes related the SBI 0.1 vs 0.2 split
- remove STRICT_KERNEL_RWX for !MMU, which isn't useful"
* tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: select ARCH_HAS_STRICT_KERNEL_RWX only if MMU
riscv: sbi: Fix undefined reference to sbi_shutdown
tty: riscv: Using RISCV_SBI_V01 instead of RISCV_SBI
riscv: sbi: Correct sbi_shutdown() and sbi_clear_ipi() export
riscv: fix vdso build with lld
RISC-V: stacktrace: Declare sp_in_global outside ifdef
Currently the following messages are seen when booting i.MX8QXP:
fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)
It is not really useful to have such messages on every boot, so change
them to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below error reported by coccicheck
drivers/tty/serial/bcm63xx_uart.c:848:2-8: ERROR: missing clk_put;
clk_get on line 842 and execution via conditional on line 846
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587472306-105155-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
breaks the UART on Cubieboard7-lite (based on S700 SoC), This is due to the
fact that generic clk routine clk_disable_unused() disables the gate clks,
and that in turns disables OWL UART (but UART driver never enables it). To
prove this theory, Andre suggested to use "clk_ignore_unused" in kernel
commnd line and it worked (Kernel happily lands into RAMFS world :)).
This commit fix this up by adding clk_prepare_enable().
Fixes: 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587067917-1400-1-git-send-email-amittomer25@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As shown in SBI v0.2, the legacy console SBI functions (sbi_console_getchar()
and sbi_console_putchar()) are expected to be deprecated; they have no replacement.
Let's HVC_RISCV_SBI and SERIAL_EARLYCON_RISCV_SBI depends on RISCV_SBI_V01.
Fixes: efca139892 ("RISC-V: Introduce a new config for SBI v0.1")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Sparc HV console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Link: https://lore.kernel.org/r/20200402172026.79478-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of accessing the registers and checking for tx_empty,
use cdns_uart_tx_empty in cdns_uart_console_write function.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-3-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci.h file includes the legacy <linux/gpio.h> header
but the driver is actually migrated to use the mctrl_gpio
library so this is not needed.
Cc: George G. Davis <george_davis@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200415180250.221762-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable i is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed. Also rename i to ret as this new
name makes makes more sense.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200405135423.383466-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the following:
var_compare_op: Comparing chan to null implies that chan might be null.
1234 if (chan)
1235 dmaengine_terminate_all(chan);
1236
Dereference after null check (FORWARD_NULL)
var_deref_op: Dereferencing null pointer chan.
1237 dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
Technically, this is correct. But lpuart_dma_rx_free() is guarded by
lpuart_dma_rx_use which is only true if there is a dma channel, see
lpuart_rx_dma_startup(). In any way, this looks bogus. So remove
the superfluous "if (chan)" check and make coverity happy.
Fixes: a092ab25fd ("tty: serial: fsl_lpuart: fix DMA mapping")
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200403174942.9594-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the OMAP serial driver to use a GPIO descriptor
for the optional RTS signal.
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415183927.269445-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver includes <linux/gpio.h> but does not use any symbols
from the file so drop this include.
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415184300.269889-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Commit 7f9803072f ("serial: 8250: Support console on software emulated
rs485 ports") amended serial8250_console_write() with rs485 support, but
positioned the invocation of ->rs485_stop_tx() after re-enablement of
interrupts. The irq handler and ->console_write() are serialized with
the port spinlock, so no problem there, but due to the rs485 delay, the
irq handler may unnecessarily spin for a while. Avoid that by moving
->rs485_stop_tx() before re-enablement of interrupts, which also mirrors
the order at the beginning of serial8250_console_write().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/019839cb1f61b01210b6ff9ac9f9079ca77f8411.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a silly copy-paste mistake, commit 7f9803072f ("serial: 8250:
Support console on software emulated rs485 ports") erroneously pauses
for the duration of delay_rts_before_send after writing to the console,
instead of delay_rts_after_send. Mea culpa.
Fixes: 7f9803072f ("serial: 8250: Support console on software emulated rs485 ports")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9dd67f33c90d23f7fafa3b81b1e812ddabf9ca24.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-test reported an error:
config: mips-randconfig-a001-20200321 ...
>> drivers/tty/serial/sprd_serial.c:1175: undefined reference
to `clk_set_parent'
Because some mips Kconfig selects HAVE_CLK but not COMMON_CLK and no
clk_set_parent implemented, so the error was exposed. So adding
dependence on COMMON_CLK can fix this issue.
Fixes: 7ba87cfec7 ("tty: serial: make SERIAL_SPRD not depend on ARCH_SPRD")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200325081427.20312-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of lpuart_dma_tx_request() is an negative errno on
failure and zero on success.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move dma_request_chan() out of the atomic context. First this call
should not be in the atomic context at all and second the
dev_info_once() may cause a hang because because the console takes this
spinlock, too.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for omap-serial
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321204031.30369-1-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART on K3 SoCs has configurable RX timeout behavior (controlled via
EFR2) and better DMA integration. This allows to transfer as larger
amount data per DMA transfer compared to older SoCs. Add support for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-7-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per Advisory 27 of AM437x Silicon errata document, Spurious UART
interrupts may occur when DMA mode (FCR.DMA_MODE) is enabled. The
Interrupt Controller flags that a UART interrupt has occurred; however,
the associated IT_PENDING bit remains set to 1, indicating that no
interrupt is pending. Acknowledge the spurious interrupts for every
occurrence as workaround.
Errata is applicable to all TI SoCs with this IP.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-6-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although same 8250 compliant UART IP is reused across different SoC,
their integration wrt DMA varies greatly across SoCs. Therefore,
different SoC may need to use different FIFO trigger level for DMA
event and DMA configuration parameters. Provide a way to pass this
information via driver data. This is required to support UART DMA on
AM654/J721e SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-5-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Caller functions of __dma_rx_do_complete() already hold rx_dma_lock.
Therefore move locking out of the function to avoid need to release and
reacquire lock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-4-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account data stuck in DMA internal buffers before pushing data
to higher layer. dma_tx_state has "in_flight_bytes" member that provides
this information.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call stop_rx() to halt reception when throttle is requested. Update
unthrottle callback to restart reception.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that all bytes are transmitted out of Uart by monitoring
CDNS_UART_SR_TACTIVE bit as well.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/e2514818af5973be291cc117d07739f068b71639.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termios function should not wait for the transmit FIFO empty
(CDNS_UART_SR_TXEMPTY) unconditionally. The tty layer takes care
of it based on the parameter passed (TCSANOW/TCSADRAIN/TCSAFLUSH).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/536e190dd5bbb474007a67e6323c048288942a28.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092930.24433-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to cleanup sprd_port anymore, since we've dropped the way
of using the sprd_port[] array to get port index.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the process of getting serial port number, with
this patch, serial devices must have aliases configured in devicetree.
The serial port searched out via sprd_port array maybe wrong if we don't
have serial alias defined in devicetree, and specify console with command
line, we would get the wrong port number if other serial ports probe
failed before console's. So using aliases is mandatory.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It would be too tricky and error prone to allow DMA operations on
kernel console.
One of the concern is when DMA is a separate device, for example on
Intel CherryTrail platforms, and might need special work around to be
functional, see the commit
eebb3e8d8a ("ACPI / LPSS: override power state for LPSS DMA device")
for more information.
Another one is that kernel console is used in atomic context, e.g.
when printing crucial information to the user (Oops or crash),
and DMA may not serve due to power management complications
including non-atomic ACPI calls but not limited to it (see above).
Besides that, other concerns are described in the commit
84b40e3b57 ("serial: 8250: omap: Disable DMA for console UART")
done for OMAP UART and may be repeated here.
Disable any kind of DMA operations on kernel console due to above concerns.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing any kind of power management for kernel console is really bad idea.
First of all, it runs in poll and atomic mode. This fact attaches a limitation
on the functions that might be called. For example, pm_runtime_get_sync() might
sleep and thus can't be used. This call needs, for example, to bring the device
to powered on state on the system, where the power on sequence may require
on-atomic operations, such as Intel Cherrytrail with ACPI enumerated UARTs.
That said, on ACPI enabled platforms it might even call firmware for a job.
On the other hand pm_runtime_get() doesn't guarantee that device will become
powered on fast enough.
Besides that, imagine the case when console is about to print a kernel Oops and
it's powered off. In such an emergency case calling the complex functions is
not the best what we can do, taking into consideration that user wants to see
at least something of the last kernel word before it passes away.
Here we modify the 8250 console code to prevent runtime power management.
Note, there is a behaviour change for OMAP boards. It will require to detach
kernel console to become idle.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future we would like to disable power management on the serial devices
used as kernel consoles to avoid weird behaviour in some cases. However,
disabling PM may prevent system to go to deep sleep states, which in its turn
leads to the higher power consumption.
Tony Lindgren proposed a work around, i.e. allow user to detach such consoles
to make PM working again. In case user wants to see what's going on, it also
provides a mechanism to attach console back.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 175b558d0e.
When the user configures a kernel without support for Samsung SoCs, it
makes no sense to ask the user about enabling "Samsung SoC serial
support", as Samsung serial ports can only be found on Samsung SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200306102301.16870-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes: f4487db58e ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function sprd_console_setup() would be called from .probe() which can
be called after freeing __init functions, for example the .probe() would
return -EPROBE_DEFER since it depends on clock modules.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, the purpose is to
keep the console port alive as possible even if there's some error
caused by no clock configured under serial devicetree nodes. But with
the patch [1], the console port couldn't be identified if missing
console command line.
So this patch adds using another interface to do check by reading
stdout-path.
[1] https://lore.kernel.org/lkml/20190826072929.7696-4-zhang.lyra@gmail.com/
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The geni serial driver's shutdown code had a special case to call
console_stop(). Grepping through the code, it was the only serial
driver doing something like this (the only other caller of
console_stop() was in serial_core.c).
As far as I can tell there's no reason to call console_stop() in the
geni code. ...and a good reason _not_ to call it. Specifically if
you have an agetty running on the same serial port as the console then
killing the agetty kills your console and if you start the agetty
again the console doesn't come back.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.2.I3648fac6c98b887742934146ac2729ecb7232eb1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a board using qcom_geni_serial I found that I could no longer
interact with kdb if I got a crash after the "agetty" running on the
same serial port was killed. This meant that various classes of
crashes that happened at reboot time were undebuggable.
Reading through the code, I couldn't figure out why qcom_geni_serial
felt the need to run so much code at port shutdown time. All we need
to do is disable the interrupt.
After I make this change then a hardcoded kgdb_breakpoint in some late
shutdown code now allows me to interact with the debugger. I also
could freely close / re-open the port without problems.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.1.Icf54c533065306b02b880c46dfd401d8db34e213@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'source' (include) all of the tty/*/Kconfig files from
drivers/tty/Kconfig instead of from drivers/char/Kconfig.
This consolidates them both in source code and in menu
presentation to the user.
Move hvc/Kconfig and serial/Kconfig 'source' lines into the
if TTY/endif block and remove the if TTY/endif blocks from
those 2 files.
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Jiri Slaby <jslaby@suse.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200311225736.32147-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor uart_unlock_and_check_sysrq() to:
- explicitly show that we release a port lock which makes
static analyzers happy:
CHECK drivers/tty/serial/serial_core.c
.../serial_core.c:3290:17: warning: context imbalance in 'uart_unlock_and_check_sysrq' - unexpected unlock
- use flags instead of irqflags to avoid confusion with IRQ flags
- provide one return point
- be more compact
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200310174337.74109-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in SysRq code instead of open coded variant.
This eliminates the conditional entirely for SERIAL_CORE_CONSOLE=n case.
While here, refactor the conditional to be more compact.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useful to see on the serial console the magic sequence itself
to enable SysRq without rummaging source code.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiler is not happy about using ARRAY_SIZE() in comparison to smaller type:
CC drivers/tty/serial/serial_core.o
.../serial_core.c: In function ‘uart_try_toggle_sysrq’:
.../serial_core.c:3222:24: warning: comparison is always false due to limited range of data type [-Wtype-limits]
3222 | if (++port->sysrq_seq < (ARRAY_SIZE(sysrq_toggle_seq) - 1)) {
| ^
Looking at the code it appears that there is an additional weirdness,
i.e. use ARRAY_SIZE() against simple string literal. Yes, the idea probably
was to allow '\0' in the sequence, but it's impractical: kernel configuration
won't accept it to begin with followed by a comment about '\0' before
comparison in question.
Drop all these by switching to strlen() and convert code accordingly.
Note, GCC seems clever enough to calculate string length at compile time.
Fixes: 68af43173d ("serial/sysrq: Add MAGIC_SYSRQ_SERIAL_SEQUENCE")
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix the RX cancel command failure, rx_fifo buffer needs to be
flushed in stop_rx() by calling handle_rx().In handle_rx() the data
in rx_fifo buffer is read and then dropped, not sent to upper layers.
If set_termios is called before startup, by this time memory is not
allocated to port->rx_fifo buffer, which leads to a NULL pointer
dereference.
To avoid this NULL pointer dereference allocate memory to port->rx_fifo
in probe itself.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reported-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1583477228-32231-2-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver for the Intel MID never seems to have been properly
integrated upstream: the platform data in <linux/spi/ifx_modem.h>
is not used anywhere in the kernel and haven't been since it was
merged into the kernel in 2010.
There might be out-of-tree users, so I don't want to delete the
driver, but I will refactor it to use GPIO descriptors, which
means that out-of-tree users will need to adapt.
There are several examples in the kernel of how to provide the
resources necessary for using GPIO descriptors to pass in the
GPIO lines, for the MID platform in particular, it will suffice
to inspect the code in files like:
arch/x86/platform/intel-mid/device_libs/platform_bt.c
This refactoring transfers all GPIOs in the driver, including
a hard-coded "PMU reset" in the driver to use GPIO descriptors
instead.
The following named GPIO descriptors need to be supplied:
- reset
- power
- mrdy
- srdy
- rst_out
- pmu_reset
Cc: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311083131.693908-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The &spi->dev is used so many times that the code gets
visibly better by introducing a simple dev helper variable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200311083131.693908-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a early_console_setup() for the LS1028A SoC with 32bit, little
endian access. If the bootloader does a fixup of the clock-frequency
node the baudrate divisor register will automatically be set.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-5-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LS1028A uses little endian register access and has a different FIFO
size encoding.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.
The error messages look like:
[ 19.012140] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
[ 19.023593] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
This was tested on a custom board with a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA channel might not be available at probe time. This is esp. the
case if the DMA controller has an IOMMU mapping.
There is also another caveat. If there is no DMA controller at all,
dma_request_chan() will also return -EPROBE_DEFER. Thus we cannot test
for -EPROBE_DEFER in probe(). Otherwise the lpuart driver will fail to
probe if, for example, the DMA driver is not enabled in the kernel
configuration.
To workaround this, we request the DMA channel in _startup(). Other
serial drivers do it the same way.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_ATMEL_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200310133057.86840-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_PIC32_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311090027.64441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the vt fixes in here and it resolves a merge issue with
drivers/tty/vt/selection.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a61 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
As a measure of balance between on and off options, add
MAGIC_SYSRQ_SERIAL_SEQUENCE which is a string sequence that can enable
sysrq if it follows BREAK on a serial line. The longer the string - the
less likely it may be in the garbage.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
Based-on-patch-by: Vasiliy Khoruzhick <vasilykh@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-3-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal if data
is transmitted through the tty layer.
Console messages bypass the tty layer and instead are emitted via
serial8250_console_write(). Amend that function to drive RTS as well,
allowing for a console on rs485 ports.
Note that serial8250_console_write() may be called concurrently to the
tty layer accessing the port. The two protect their accesses with the
port lock, but serial8250_console_write() may find RTS still being
asserted by the tty layer, in which case it shouldn't be deasserted
after the console message has been printed. Recognize such situations
by checking the em485->tx_stopped flag.
If a delay_rts_before_send or delay_rts_after_send has been specified,
serial8250_console_write() busy-waits for its duration. Optimizations
for those wait times are conceivable: E.g. if RTS is already asserted,
we could check whether em485->start_tx_timer is active and wait only
for the remaining expire time. But this would require calling into
the hrtimer infrastructure, which involves acquiring locks and
potentially reprogramming timer hardware. Such operations seem too
risky in the context of console printout, which needs to work even when
the kernel has crashed and emits a BUG splat. So I've gone with a
simplistic solution which just always waits for the full delay.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/65edffce4670a19e598015c03cbe46f1ffd93e43.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend 8250_bcm2835aux.c to support rs485 as introduced for 8250_omap.c
by commit e490c9144c ("tty: Add software emulated RS485 support for
8250").
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register: If the bit is clear, RTS is high. With omap, it's
apparently the other way round.
Moreover, omap achieves half-duplex mode by disabling the UART_IER_RDI
interrupt and clearing the RX FIFO when TX stops. This approach doesn't
work on bcm2835aux because the UART_LSR_DR bit is set even when
UART_IER_RDI is disabled. Consequently, serial8250_handle_irq() invokes
serial8250_rx_chars() to empty the FIFO and characters are received even
though the user requested half-duplex. Solve by disabling the receiver
using the non-standard CNTL register.
Cache that register in the driver's private data for performance. Set
the private data pointer before calling serial8250_register_8250_port()
to prevent a null pointer deref in case one of the rs485 callbacks is
invoked immediately after port registration.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/dd86460e20a8f979b7272a0bde73640312b902b1.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far the only drivers taking advantage of it are 8250_omap.c and
8250_of.c.
We're about to make use of the feature in 8250_bcm2835aux.c as well.
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register. Moreover, omap achieves half-duplex mode by
disabling the RX interrupt and clearing the RX FIFO when TX stops.
The bcm2835aux requires disabling the receiver instead.
Support these behavioral differences by generalizing the rs485 emulation:
Introduce ->rs485_start_tx() and ->rs485_stop_tx() callbacks in struct
uart_8250_port, provide generic implementations containing the existing
code and use them as callbacks in 8250_omap.c and 8250_of.c.
start_tx_rs485() is idempotent in that it recognizes whether RTS is
already asserted. Achieve the same by introducing a tx_stopped flag in
struct uart_8250_em485. This may even perform a little better on arches
where memory access is faster than mmio access.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/5ac0464ae4414708e723a1e0d52b0c1b2bd41b9b.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When rs485 transmission over an 8250 port stops, __stop_tx() assigns
active_timer = NULL before calling __stop_tx_rs485().
That function in turn either assigns active_timer = stop_tx_timer and
rearms the timer (in case a delay_rts_after_send needs to be observed)
or directly calls __do_stop_tx_rs485().
Move the assignment active_timer = NULL to __stop_tx_rs485() into the
branch which directly calls __do_stop_tx_rs485(), thereby avoiding a
duplicate assignment and simplifying the code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/bca638405550eaf92f0c6060b553b687f35885e0.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the generic ->rs485_config() callback to sanitize RTS polarity and
zero-fill the padding (in addition to the existing sanitization of the
RTS delays).
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/ff833721bc372d38678f289eb2a44dbf016d5203.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
Drivers opt in to the feature by calling serial8250_em485_init() from
their ->rs485_config() callback.
So far there are two drivers doing that, 8250_omap.c and 8250_of.c.
Both use an identical callback. We're about to add a third user of that
callback, therefore deduplicate it and move it to 8250_port.c.
Drivers now opt in to rs485 software emulation by assigning the generic
serial8250_rs485_config() callback introduced herein to their
.rs485_config struct member. This change allows unexporting
serial8250_em485_init() and declaring it static.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/fcef63642dc4eae41ae7842d23747b2bf5d40285.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of 8250 ports in
case they are attached to an rs485 transceiver.
If the property "linux,rs485-enabled-at-boot-time" is present, invoke
the ->rs485_config() callback to immediately deassert RTS, thereby
ceasing control of the bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5908ea89b7f9da54872d6634b606d83db032297a.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_mctrl() currently allows modifying the RTS modem
control line even when RTS is used as an rs485 Transmit Enable signal.
It is thus possible for user space to interfere with rs485 communication
by invoking a TIOCMSET ioctl().
Ignore such change requests and retain the current RTS polarity when in
rs485 mode. Note that serial8250_set_mctrl() is always called with
port->lock held, so there's no risk that RTS is changed concurrently.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/b1ce34ca9bc4d7bdc6e9852fcf30b1f4e37c8a80.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a driver exposes early consoles with EARLYCON_DECLARE() and
OF_EARLYCON_DECLARE(), pefer the non-OF variant if the user specifies it
by
earlycon=<driver>,<options>
The rationale behind this is that some drivers register multiple setup
functions under the same driver name. Eg.
OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
It depends on the order of the entries which console_setup() actually
gets called. To make things worse, I guess it also depends on the
compiler how these are ordered. Thus always prefer the EARLYCON_DECLARE()
ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200220174607.24285-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to tty serial drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301204517.GA10368@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node
dependence") the port line number can also be allocated by IDA, but in
case of an error the ID will no be removed again. More importantly, any
ID will be freed in remove(), even if it wasn't allocated but instead
fetched by of_alias_get_id(). If it was not allocated by IDA there will
be a warning:
WARN(1, "ida_free called for id=%d which is not allocated.\n", id);
Move the ID allocation more to the end of the probe() so that we still
can use plain return in the first error cases.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200303174306.6015-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a659652f61.
This broke the earlycon on LS1021A processors because the order of the
earlycon_setup() functions were changed. Before the commit the normal
lpuart32_early_console_setup() was called. After the commit the
lpuart32_imx_early_console_setup() is called instead.
Fixes: a659652f61 ("tty: serial: fsl_lpuart: drop EARLYCON_DECLARE")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200303174306.6015-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the dependency with ARCH_SPRD from sprd serial/console Kconfig-s,
since we want them can be built-in when ARCH_SPRD is set as 'm'.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200305103228.9686-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->setup() callback is mandatory for the devices.
Provide it for Elkhart Lake UART ports.
Note, for time being it's empty, but in the future it might require
an additional configuration such as DMA.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200305130822.36850-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MTK uart design no need to control uart clock,
so we just control bus clock in runtime function.
Add uart clock used count to avoid repeatedly switching the clock.
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Link: https://lore.kernel.org/r/1582707225-26815-1-git-send-email-changqi.hu@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The peripheral has support for inverting its input and/or output
signals. This is useful if the hardware flips polarity of the
peripheral's signal, such as swapped +/- pins on an RS-422 transceiver,
or an inverting level shifter. Add support for these control registers
via the device tree binding.
As part of this change, make the writes of the various registers more
uniform by moving the UCR3 block up near the other registers' blocks,
since the INVT bit must be set before enabling the peripheral.
Signed-off-by: George Hilliard <ghilliard@kopismobile.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200226222319.18383-3-ghilliard@kopismobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulate half-duplex operation and use mctrl_gpio to add support for
RS485 tranceiver with transmit/receive switch hooked to RTS GPIO line.
This is needed to make use of the RS485 port found on Teltonika RUT955.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200221212331.GA21467@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPM UART (PowerPC) has an open coded GPIO modem control
handling. Since I can't test this I can't just migrate it to
the serial mctrl GPIO helper library though I wish I could.
I do second best and convert it to GPIO descriptors at least.
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229231842.247563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from <linux/gpio.h>
so drop this include.
Cc: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Cc: Songjun Wu <songjun.wu@linux.intel.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229212331.174946-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from these GPIO
includes so drop them. These are probably just historical
artifacts from befor mctrl_gpio was used.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200229220941.205599-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>