Switch default pcbeep path to Line in path.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ALC256 does not have a mixer nid at 0x0b, and there's no
loopback path (the output pins are directly connected to the DACs).
This commit fixes an "num_steps = 0 for NID=0xb (ctl = Beep Playback Volume)"
error (and as a result, problems with amixer/alsamixer).
If there's pcbeep functionality, it certainly isn't controlled by setting an
amp on 0x0b, so disable beep functionality (at least for now).
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1446517
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addes AZX_DCAPS_I915_POWERWELL to BYT (Baytrail).
Like Braswell and Skylake, the HDMI codec on Bytrail is also in the shared
power well with GPU. This power well must be turned on before we reset link
to probe the codec, to avoid communication failure with the codec.
The side effect is that this power is always ON in S0 because the BYT HDMI
codec does not support EPSS or D3ClkStop and so the controller doesn't enter
D3 at runtime, and the HDMI codec and analog codec share a single physical
HD-A link and so we cannot reset the HD-A link freely when we re-enable the
power to use the HDMI codec.
Next step is to test if an AGP reset or double AGP reset on BYT HDMI codec is
okay to bring the HDMI codec back to a functional state after restoring the
power. If okay, we can bind the power on/off with the HDMI codec PM without
interrupting the analog audio.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only Intel Haswell and Broadwell have a separate HD-A controller (PCI device 3)
for display audio, which needs to get 24MHz HD-A link BCLK from the variable
display core clock through vendor specific registers EM4 & EM5. Other platforms
(Baytrail, Braswell and Skylake) don't have this feature.
So this patch checks the PCI device ID of the controller in haswell_set_bclk()
and only sync BCLK for HSW and BDW.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Muting the headphone output pin right before the codec suspension
prevents pop noises when headphones are plugged in (except for a
barely audible click noise).
This solution allows to truly save some power when headphones are
plugged in unlike the previous solution (033b0a7ca9:
"ALSA: hda - Pop noises fix for XPS13 9333")
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function is a bit unusual because it accepts negative values as
"conn_len". It's theoretically possible for both "cache_len" and
"conn_len" to be -ENOSPC and in that case we would oops trying to run
memcmp() on the uninitialized "list" pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [a551d91473: ALSA: hda - Use regmap for command verb
caches, too] introduced a regression due to a typo in the conversion;
the IEC958 status bits of slave digital devices aren't updated
correctly. This patch corrects it.
Fixes: a551d91473 ('ALSA: hda - Use regmap for command verb caches, too')
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DEVICE_ALI previously would jump to port_inited after calling
pci_iomap(), bypassing the check for bmaddr being NULL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because AZX_DCAPS_PM_RUNTIME is always defined as non-zero, the
initial part of the expression can be skipped.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Thinkpad T450 requires the ALC292_FIXUP_TPT440_DOCK as well in
order to get working sound output on the docking stations headphone jack.
Patch tested on a Thinkpad T450 (20BVCTO1WW) using kernel 4.0-rc7 in
conjunction with a ThinkPad Ultradock.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The optical ports on the E-mu 1010 (and dock) can be configured
for ADAT- or S/PDIF-mode, which is currently hardcoded to ADAT.
Add two mixer elements to expose this setting.
Tested on an E-mu 1010 PCIe with connected Micro Dock.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the dock on an E-mu 1010 card is disconnected, all outputs get
muted by the hardware. Add logic to detect a disconnect and unmute.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model uses the same dock port as the previous generation.
Signed-off-by: Yves-Alexis Perez <corsac@debian.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The functions snd_emu10k1_proc_spdif_read and snd_emu1010_fpga_read
acquire the emu_lock before accessing the FPGA. The function used
to access the FPGA (snd_emu1010_fpga_read) also tries to take
the emu_lock which causes a deadlock.
Remove the outer locking in the proc-functions (guarding only the
already safe fpga read) to prevent this deadlock.
[removed superfluous flags variables too -- tiwai]
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A comma was used instead of a semicolon, which may lead to a build
error.
Fixes: cffd396681 ('ALSA: hda/realtek - Fix the regression by widget power-saving')
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the case for Realtek, VIA codec driver needs this ops as
well for making the widget power-save working.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While enabling the widget power-saving for ALC269 & co, the important
setup was forgotten -- stream_pm ops. Without this setup, the paths
for PCM won't be powered up at all.
Also, the power_filter callbacks used in ALC269 & co need to chain to
the default snd_hda_gen_path_power_filter().
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the generic parser sets codec->power_filter when
power_save_node flag is set. But this overrides the existing filter
that has been already set by the codec driver, thus it looses some
features. Instead, set the default power_filter only when it's not
set yet.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the check of power_save_node flag at the beginning of the function
so that it skips the rest if the flag isn't set. In this way, we can
call this function safely no matter whether the widget power-saving is
really used or not.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the widget power-saving is enabled, the first automute hook
invocation checks through the whole pins and it also tries to
synchronize the power state. However, this results in a wrong state
because it calls unconditionally snd_hda_jack_detect_state().
This patch adds a check of jack detectability before the actual jack
detection call.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new widget power-saving tries to apply the power change no matter
whether the node has a power cap or not. It's bad (although most of
codecs chip just ignore it). Check the capability properly
beforehand.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some BIOS version of Fujitsu Lifebook T731 seems to set up the
headphone pin (0x21) without the assoc number 0x0f while it's set only
to the output on the docking port (0x1a). With the recent commit
[03ad6a8c93: ALSA: hda - Fix "PCM" name being used on one DAC when
there are two DACs], this resulted in the weird mixer element
mapping where the headphone on the laptop is assigned as a shared
volume with the speaker and the docking port is assigned as an
individual headphone.
This patch improves the situation by correcting the headphone pin
config to the more appropriate value.
Reported-and-tested-by: Taylor Smock <smocktaylor@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell create new platform with ALC288 codec.
This patch will enable headset mode for Dino platform.
[slight code refactoring and compile fix by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin sense will active when power pin is wake up.
Power pin will not wake up immediately during resume state.
Add some delay to wait for power pin activated.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI/DP codec on SKL/BSW is in the power well.
The power well must be turned on before probing the
HDMI/DP codec.
This is a temporary patch, which will power on the
powerwell by adding AZX_DCAPS_I915_POWERWELL for SKL
and BSW. After restructuring and new flag is added,
this patch will be reverted.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Audigy 5/Rx is essentially an Audigy 4 behind a PLX PCIe-
bridge with an additional TOSLINK output.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
we are dereferencing pcm first then checking pcm. instead now lets put
them in same if condition so that pcm is checked first.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell new platform of ALC256 audio codec.
Support headset mode for Dell ALC256 platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent Realtek codecs support the finer power state control on each
widget. Let's enable the new feature.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far we assumed that the node attributes like amp values remain
during the power state transition of the node itself. While this is
true for IDT/STAC codecs I've tested, but some other codecs don't seem
behaving in that way.
This patch implements a partial sync mechanism specific to the given
widget node. Now we've merged the regmap support, and it can be
easily written with regcache_sync_region().
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the support of regmap in HD-audio infrastructure.
Many in-house cache codes in HD-audio driver are relaced with the
more standard regmap base now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1436745
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My codec has a beep-generating node:
$ cat /proc/asound/card1/codec#0
Codec: VIA VT1802
...
Vendor Id: 0x11068446
Subsystem Id: 0x15587410
Revision Id: 0x100000
...
Node 0x22 [Beep Generator Widget] wcaps 0x70040c: Mono Amp-Out
Amp-Out caps: ofs=0x0a, nsteps=0x12, stepsize=0x05, mute=1
Amp-Out vals: [0x0a]
Power states: D0 D1 D2 D3
Power: setting=D0, actual=D0
...
But I was missing the:
Control: name=...
entries that I need to manage this widget from alsamixer. With this
patch (based on the similar Mono Amp-Out handling in
patch_conexant.c), I get a new:
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input15
entry in dmesg and controls to manage that beep:
$ cat /proc/asound/card1/codec#0 | grep -A5 Beep
Node 0x22 [Beep Generator Widget] wcaps 0x70040c: Mono Amp-Out
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=1, dir=Out, idx=0, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=1, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x0a, nsteps=0x12, stepsize=0x05, mute=1
Amp-Out vals: [0x12]
Power states: D0 D1 D2 D3
Power: setting=D0, actual=D0
[rebased and modified for the latest tree by tiwai]
Signed-off-by: W. Trevor King <wking@tremily.us>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just forgotten to remove. It's now in sound/hdaudio.h.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace duplicated const keyword for 'sampleclock_sources' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This model uses the same dock port as the previous generation.
Signed-off-by: Sebastian Wicki <gandro@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to cap "ucontrol->id.index / num_busses_in(chip)" so the we
don't read beyond the end of the array.
I also adding a check on "in" and changing the type in
snd_echo_mixer_put() from short to unsigned int. Those changes are done
for symmetry and are cosmetic.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target. But this conversion
needs a bit more caution than before.
- In the old code, we just record any verbs as is, and restore them at
resume. For the regmap scheme, this doesn't work, since a few verbs
like AMP or DIGI_CONVERT are asymmetrical. Such verbs are converted
either to the dedicated function (snd_hda_regmap_xxx_amp()) or
changed to the unified verb.
- Some verbs have to be declared as vendor-specific ones before
accessing via regmap.
Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation. Further
optimizations will be brought in the later patches, if any.
This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the amp access functions to the regmap helpers.
The amp values were formerly cached in the own hash table. Now it's
dropped by the regmap's cache.
The only tricky conversion is snd_hda_codec_amp_init(). This function
shouldn't do anything if the amp was already initialized. For
achieving this behavior, a value is read once at first temporarily in
the cache-only mode. Only if it returns an error, i.e. the item
still doesn't exist in the cache, it proceeds to the update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes we need the uncached reads, e.g. for refreshing the tree.
This patch provides the helper function for that and uses it for
refreshing widgets, reading subtrees and the whole proc reads.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
