Here is the large set of driver changes for char/misc drivers and other
smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem seems
under very active development recently. This required also merging
in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/inQw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yksvwCeOvU//SPwrbIpaeHAmHUv0PSVOrwAoKmt4ICh
hQUudlztfkvUJxKIH0gh
=Sjk4
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the large set of driver changes for char/misc drivers and
other smaller driver subsystems that flow through this git tree.
Included in here are:
- New IIO drivers and features and improvments in that subsystem
- New hwtracing drivers and additions to that subsystem
- lots of interconnect changes and new drivers as that subsystem
seems under very active development recently. This required also
merging in the icc subsystem changes through this tree.
- FPGA driver updates
- counter subsystem and driver updates
- MHI driver updates
- nvmem driver updates
- documentation updates
- Other smaller driver updates and fixes, full details in the
shortlog
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (223 commits)
scripts/tags.sh: fix incompatibility with PCRE2
firmware: coreboot: Remove GOOGLE_COREBOOT_TABLE_ACPI/OF Kconfig entries
mei: lower the log level for non-fatal failed messages
mei: bus: disallow driver match while dismantling device
misc: vmw_balloon: fix memory leak with using debugfs_lookup()
nvmem: stm32: fix OPTEE dependency
dt-bindings: nvmem: qfprom: add IPQ8074 compatible
nvmem: qcom-spmi-sdam: register at device init time
nvmem: rave-sp-eeprm: fix kernel-doc bad line warning
nvmem: stm32: detect bsec pta presence for STM32MP15x
nvmem: stm32: add OP-TEE support for STM32MP13x
nvmem: core: use nvmem_add_one_cell() in nvmem_add_cells_from_of()
nvmem: core: add nvmem_add_one_cell()
nvmem: core: drop the removal of the cells in nvmem_add_cells()
nvmem: core: move struct nvmem_cell_info to nvmem-provider.h
nvmem: core: add an index parameter to the cell
of: property: add #nvmem-cell-cells property
of: property: make #.*-cells optional for simple props
of: base: add of_parse_phandle_with_optional_args()
net: add helper eth_addr_add()
...
-----BEGIN PGP SIGNATURE-----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=cBvC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023022201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Benjamin Tissoires:
- HID-BPF infrastructure: this allows to start using HID-BPF. Note that
the mechanism to ship HID-BPF program through the kernel tree is
still not implemented yet (but is planned).
This should be a no-op for 99% of users. Also we are gaining
kselftests for the HID tree (Benjamin Tissoires)
- Some UAF fixes in workers when using uhid (Pietro Borrello & Benjamin
Tissoires)
- Constify hid_ll_driver (Thomas Weißschuh)
- Allow more custom IIO sensors through HID (Philipp Jungkamp)
- Logitech HID++ fixes for scroll wheel, protocol and debug (Bastien
Nocera)
- Some new device support: Steam Deck (Vicki Pfau), UClogic (José
Expósito), Logitech G923 Xbox Edition steering wheel (Walt Holman),
EVision keyboards (Philippe Valembois)
- other assorted code cleanups and fixes
* tag 'for-linus-2023022201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (99 commits)
HID: mcp-2221: prevent UAF in delayed work
hid: bigben_probe(): validate report count
HID: asus: use spinlock to safely schedule workers
HID: asus: use spinlock to protect concurrent accesses
HID: bigben: use spinlock to safely schedule workers
HID: bigben_worker() remove unneeded check on report_field
HID: bigben: use spinlock to protect concurrent accesses
HID: logitech-hidpp: Add myself to authors
HID: logitech-hidpp: Retry commands when device is busy
HID: logitech-hidpp: Add more debug statements
HID: Add support for Logitech G923 Xbox Edition steering wheel
HID: logitech-hidpp: Add Signature M650
HID: logitech-hidpp: Remove HIDPP_QUIRK_NO_HIDINPUT quirk
HID: logitech-hidpp: Don't restart communication if not necessary
HID: logitech-hidpp: Add constants for HID++ 2.0 error codes
Revert "HID: logitech-hidpp: add a module parameter to keep firmware gestures"
HID: logitech-hidpp: Hard-code HID++ 1.0 fast scroll support
HID: i2c-hid: goodix: Add mainboard-vddio-supply
dt-bindings: HID: i2c-hid: goodix: Add mainboard-vddio-supply
HID: i2c-hid: goodix: Stop tying the reset line to the regulator
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmPgG/geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGidAH/j0pUbmniNM3aft8
5O1XxltlOZgqxju8OQhkiuX9VnQuuSeTNhAuj6jfcQOLpXDvlKsVfrpBxEfXalML
yead9QAy/OT3hNGQxifMQzGbsmaWH1kgxxnv2lKo2eNP5KYZ+rec+IgtQhgX9quN
q/N/ymd2/ju9AEOVRYwG1PD1EiIwTd3xPfBZl4Z35J+Ym+6NRrlXmN6J9LwslXmJ
/P4cwgdf9/TuYAB96EshRHsZ4Tk/Gxkn15uyhLaWBmrZ/LAF5JGbClEfFlCWgjwv
F5SGv3F+O6HSv49W9a24XtenE+3tw78AbCdqKZyzbb2whhv1eY99vKSbGnCahc/y
O0VBP/g=
=YoPk
-----END PGP SIGNATURE-----
Merge 6.2-rc7 into char-misc-next
We need the char-misc driver fixes in here as other patches depend on
them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added extra spaces before statements to fix
following indentation warnings reported by checkpatch.pl.
WARNING: Statements should start on a tabstop
+ return 0;
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Link: https://lore.kernel.org/r/Y9Vf4Tp8JKvy+y0u@yoga
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch Warns:
drivers/iio/accel/mma9551_core.c:299
mma9551_read_config_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: No actual bug as caller checks the return value and does not
use the parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126153610.3586243-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Smatch Warns: drivers/iio/accel/mma9551_core.c:357
mma9551_read_status_word() error: uninitialized symbol 'v'.
When (offset >= 1 << 12) is true mma9551_transfer() will return -EINVAL
without 'v' being initialized, so check for the error and return.
Note: Not a bug as such because the caller checks return value and
doesn't not use this parameter in the problem case.
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230126152147.3585874-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
checkpatch reports
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
FILE: drivers/iio/imu/bno055/bno055_ser_trace.c:1:
+//SPDX-License-Identifier: GPL-2.0
Add a space
Fixes: 2eef5a9cc6 ("iio: imu: add BNO055 serdev driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230124194301.656518-1-trix@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC in i.mx93 is a total new ADC IP, add a driver to support
this ADC.
Currently, only support one shot normal conversion triggered by
software. For other mode, will add in future.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230117135137.1735536-2-haibo.chen@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need the name 'st_lsm6dsx_ext_info' for the actual 'iio_chan_spec_ext_info'.
Rename the 'st_lsm6dsx_ext_info' in st_lsm6dsx_shub.c to 'st_lsm6dsx_shub_info'.
For consistency, replace also 'ext' by 'shub' in 'st_lsm6dsx_ext_attributes'
and 'st_lsm6dsx_ext_attribute_group'.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/1673874434-30750-2-git-send-email-Philippe.DeMuyter@macq.eu
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700_CTRL_ODR_MIN is not used but value is probably wrong.
Remove it for a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The absence of correct offset leads a failed initialization ODR mode
assignment.
Select MAX ODR mode as the initialization ODR mode by field mask and
FIELD_PREP.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The absence of a correct offset leads an incorrect ODR mode
readback after use a hexadecimal number to mark the value from
FXOS8700_CTRL_REG1.
Get ODR mode by field mask and FIELD_GET clearly and conveniently.
And attach other additional fix for keeping the original code logic
and a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure proximity sensor interrupts and threshold
limits for vcnl4040. If an interrupt is detected an event will be
pushed to the event interface.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-4-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports 4 chips, by which only one (vcnl4010) handles
interrupts and has support for triggered buffer. The setup of these
functions is hardcoded for vcnl4010 inside the generic vcnl4000_probe,
and thus ignores the chip specific configuration structure where all
other chip specific functions are specified.
This complicates adding interrupt handler and triggered buffer support
to chips which may have support for it.
Add members for irq threads and iio_buffer_setup_ops to the generic
vcnl4000_chip_spec struct, so that instead of checking a chip specific
boolean irq support, we check for a chip specific triggered buffer
handler, and/or a chip specific irq thread handler.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-3-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to allow the chip_spec array reference the function pointers
for interrupts, the code for these functions need to be moved above the
chip_spec array.
This is a prestep to support a more generic setup of interrupts.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230117190017.3789181-2-marten.lindahl@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add initial support for DAC max5522.
Tested writing DAC A and B with some values,
from 0 to 1023, measured output voltages, driver works properly.
Additions for max5523/24/25 will follow.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20221106165928.223318-1-angelo.dureghello@timesys.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit c1e62062ff ("iio: light: cm32181: Handle CM3218 ACPI devices
with 2 I2C resources") creates a second client for the actual I2C
address, but the "struct device" passed to PM ops is the first I2C
client that can't talk to the sensor.
That means the I2C transfers in both suspend and resume routines can
fail and blocking the whole suspend process.
Instead of using the first client for I2C transfer, use the I2C client
stored in the cm32181 private struct so the PM ops can get the correct
I2C client to really talk to the sensor device.
Fixes: 68c1b3dd5c ("iio: light: cm32181: Add PM support")
BugLink: https://bugs.launchpad.net/bugs/1988346
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281
Tested-by: Wahaj <wahajaved@protonmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230118170422.339619-1-kai.heng.feng@canonical.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the current users is using gaps in the list of the items.
No need to have a specific function for that, just replace it by
library available __sysfs_match_string().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230118074828.66155-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace open coded fwnode_device_is_compatible() in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119174749.76769-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Return value should be zero for success. This was forgotten for timestamp
feature. Verified on RealSense cameras.
Fixes: 4648cbd8fb ("iio: hid-sensor-gyro-3d: Add timestamp channel")
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Link: https://lore.kernel.org/r/7c1809dc74eb2f58a20595f4d02e76934f8e9219.camel@intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Return value should be zero for success. This was forgotten for timestamp
feature. Verified on RealSense cameras.
Fixes: a96cd0f901 ("iio: accel: hid-sensor-accel-3d: Add timestamp")
Signed-off-by: Dmitry Perchanov <dmitry.perchanov@intel.com>
Link: https://lore.kernel.org/r/a6dc426498221c81fa71045b41adf782ebd42136.camel@intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113141117.23353-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support of identification registers to STM32 DFSDM
to allow hardware capabilities discovery and configuration check.
The number of filters and channels, are read from registers,
when they are available.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20230105125331.328275-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The magnetometer part of ST LSM303C is similar (perhaps even identical)
to the already supported standalone LIS3MDL magnetometer, so just
add the new st,lsm303c-magn compatible for the existing definitions.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230106102239.9647-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The accelerometer part of ST LSM303C is similar (perhaps even identical)
to the already supported standalone LIS2HH12 accelerometer, so just
add the new st,lsm303c-accel compatible for the existing definitions.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230106102239.9647-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The following kernel linkage error:
st_lsm6dsx_core.o: in function `st_lsm6dsx_sw_buffers_setup':
st_lsm6dsx_core.c:2578: undefined reference to `devm_iio_triggered_buffer_setup_ext'
is caused by the fact that the object owning devm_iio_triggered_buffer_setup_ext()
(drivers/iio/buffer/industrialio-triggered-buffer.o) is allowed to be
built as module when its user (drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c)
is built-in.
The st_lsm6dsx driver already has a "select IIO_BUFFER", so add another
select for IIO_TRIGGERED_BUFFER, to make that option follow what is set
for the st_lsm6dsx driver. This is similar to what other iio drivers do.
Fixes: 2cfb2180c3 ("iio: imu: st_lsm6dsx: introduce sw trigger support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230103130348.1733467-1-vladimir.oltean@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point to specify asm-generic for the unaligned.h.
Drop the 'generic' suffix and move the inclusion to be after
the non-IIO linux/* ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230103144903.39905-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI_PTR() is more harmful than helpful. For example, in this case
if CONFIG_ACPI=n, the ID table left unused and code is obfuscated
by ifdeffery.
Drop anti-pattern of ACPI_PTR() use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230102173450.29882-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The spi_get_device_match_data() helps to get driver data from the
firmware node or SPI ID table. Use it instead of open coding.
While at it, switch ID tables to provide an acrual pointers to
the configuration data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230102173450.29882-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is useful to be able to build this driver without needing
to build support for ARCH_EP93XX.
Also add an explicit dependency on HAS_IOMEM so we have
devm_platform_ioremap_resource() etc available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20221231144128.489810-1-jic23@kernel.org
VAC needs to be wired up to produce proper measurements,
without this change only near zero values are reported.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20221217221305.671117-1-andreas@kemnade.info
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because ACCEL and MAGN channels data register base address is
swapped the accelerometer and magnetometer channels readback is
swapped.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700 is an IMU sensor with ACCEL sensor and MAGN sensor.
Sensor type is indexed by corresponding channel type in a switch.
IIO_ANGL_VEL channel type mapped to MAGN sensor has caused confusion.
Fix the mapping label of "IIO_MAGN" channel type instead of
"IIO_ANGL_VEL" channel type to MAGN sensor.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some inputs need to be wired up to produce proper measurements,
without this change only near zero values are reported.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Fixes: 1696f36482 ("iio: twl6030-gpadc: TWL6030, TWL6032 GPADC driver")
Link: https://lore.kernel.org/r/20221201181635.3522962-1-andreas@kemnade.info
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
