This reverts commit f685a533a7.
The MIPS cache flush logic needs to know whether the mapping was already
established to decide how to flush caches. This is done by checking the
valid bit in the PTE. The commit above breaks this logic by setting the
valid in the PTE in new mappings, which causes kernel crashes.
Link: https://lkml.kernel.org/r/20210526094335.92948-1-tsbogend@alpha.franken.de
Fixes: f685a533a7 ("MIPS: make userspace mapping young by default")
Reported-by: Zhou Yanjie <zhouyanjie@wanyeetech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huang Pei <huangpei@loongson.cn>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When update the latest mainline kernel with the following three configs,
the kernel hangs during startup:
(1) CONFIG_FUNCTION_GRAPH_TRACER=y
(2) CONFIG_PREEMPT_TRACER=y
(3) CONFIG_FTRACE_STARTUP_TEST=y
When update the latest mainline kernel with the above two configs (1)
and (2), the kernel starts normally, but it still hangs when execute
the following command:
echo "function_graph" > /sys/kernel/debug/tracing/current_tracer
Without CONFIG_PREEMPT_TRACER=y, the above two kinds of kernel hangs
disappeared, so it seems that CONFIG_PREEMPT_TRACER has some influences
with function_graph tracer at the first glance.
I use ejtag to find out the epc address is related with preempt_enable()
in the file arch/mips/lib/mips-atomic.c, because function tracing can
trace the preempt_{enable,disable} calls that are traced, replace them
with preempt_{enable,disable}_notrace to prevent function tracing from
going into an infinite loop, and then it can fix the kernel hang issue.
By the way, it seems that this commit is a complement and improvement of
commit f93a1a00f2 ("MIPS: Fix crash that occurs when function tracing
is enabled").
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
rt2880_wdt.c uses (well, attempts to use) rt_sysc_membase. However,
when this watchdog driver is built as a loadable module, there is a
build error since the rt_sysc_membase symbol is not exported.
Export it to quell the build error.
ERROR: modpost: "rt_sysc_membase" [drivers/watchdog/rt2880_wdt.ko] undefined!
Fixes: 473cf939ff ("watchdog: add ralink watchdog driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
arch/mips/include/asm/mips-boards/launch.h needs an include guard
to prevent it from being #included more than once.
Prevents these build errors:
In file included from ../arch/mips/mti-malta/malta-amon.c:16:
../arch/mips/include/asm/mips-boards/launch.h:8:8: error: redefinition of 'struct cpulaunch'
8 | struct cpulaunch {
| ^~~~~~~~~
In file included from ../arch/mips/include/asm/mips-cps.h:13,
from ../arch/mips/include/asm/smp-ops.h:16,
from ../arch/mips/include/asm/smp.h:21,
from ../include/linux/smp.h:114,
from ../arch/mips/mti-malta/malta-amon.c:12:
../arch/mips/include/asm/mips-boards/launch.h:8:8: note: originally defined here
8 | struct cpulaunch {
| ^~~~~~~~~
make[3]: [../scripts/Makefile.build:273: arch/mips/mti-malta/malta-amon.o] Error 1 (ignored)
Fixes: 6decd1aad1 ("MIPS: add support for buggy MT7621S core detection")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
board-xxs1500.c references 2 functions without declaring them, so add
the header file to placate the build.
../arch/mips/alchemy/board-xxs1500.c: In function 'board_setup':
../arch/mips/alchemy/board-xxs1500.c:56:2: error: implicit declaration of function 'alchemy_gpio1_input_enable' [-Werror=implicit-function-declaration]
56 | alchemy_gpio1_input_enable();
../arch/mips/alchemy/board-xxs1500.c:57:2: error: implicit declaration of function 'alchemy_gpio2_enable'; did you mean 'alchemy_uart_enable'? [-Werror=implicit-function-declaration]
57 | alchemy_gpio2_enable();
Fixes: 8e026910fc ("MIPS: Alchemy: merge GPR/MTX-1/XXS1500 board code into single files")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In commit fa8b90070a ("quota: wire up quotactl_path") we have wired up
new quotactl_path syscall. However some people in LWN discussion have
objected that the path based syscall is missing dirfd and flags argument
which is mostly standard for contemporary path based syscalls. Indeed
they have a point and after a discussion with Christian Brauner and
Sascha Hauer I've decided to disable the syscall for now and update its
API. Since there is no userspace currently using that syscall and it
hasn't been released in any major release, we should be fine.
CC: Christian Brauner <christian.brauner@ubuntu.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/lkml/20210512153621.n5u43jsytbik4yze@wittgenstein
Signed-off-by: Jan Kara <jack@suse.cz>
- Convert sh and sparc to use generic shell scripts to generate the
syscall headers
- refactor .gitignore files
- Update kernel/config_data.gz only when the content of the .config is
really changed, which avoids the unneeded re-link of vmlinux
- move "remove stale files" workarounds to scripts/remove-stale-files
- suppress unused-but-set-variable warnings by default for Clang as well
- fix locale setting LANG=C to LC_ALL=C
- improve 'make distclean'
- always keep intermediate objects from scripts/link-vmlinux.sh
- move IF_ENABLED out of <linux/kconfig.h> to make it self-contained
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=935P
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Convert sh and sparc to use generic shell scripts to generate the
syscall headers
- refactor .gitignore files
- Update kernel/config_data.gz only when the content of the .config
is really changed, which avoids the unneeded re-link of vmlinux
- move "remove stale files" workarounds to scripts/remove-stale-files
- suppress unused-but-set-variable warnings by default for Clang
as well
- fix locale setting LANG=C to LC_ALL=C
- improve 'make distclean'
- always keep intermediate objects from scripts/link-vmlinux.sh
- move IF_ENABLED out of <linux/kconfig.h> to make it self-contained
- misc cleanups
* tag 'kbuild-v5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
linux/kconfig.h: replace IF_ENABLED() with PTR_IF() in <linux/kernel.h>
kbuild: Don't remove link-vmlinux temporary files on exit/signal
kbuild: remove the unneeded comments for external module builds
kbuild: make distclean remove tag files in sub-directories
kbuild: make distclean work against $(objtree) instead of $(srctree)
kbuild: refactor modname-multi by using suffix-search
kbuild: refactor fdtoverlay rule
kbuild: parameterize the .o part of suffix-search
arch: use cross_compiling to check whether it is a cross build or not
kbuild: remove ARCH=sh64 support from top Makefile
.gitignore: prefix local generated files with a slash
kbuild: replace LANG=C with LC_ALL=C
Makefile: Move -Wno-unused-but-set-variable out of GCC only block
kbuild: add a script to remove stale generated files
kbuild: update config_data.gz only when the content of .config is changed
.gitignore: ignore only top-level modules.builtin
.gitignore: move tags and TAGS close to other tag files
kernel/.gitgnore: remove stale timeconst.h and hz.bc
usr/include: refactor .gitignore
genksyms: fix stale comment
...
Merge more updates from Andrew Morton:
"The remainder of the main mm/ queue.
143 patches.
Subsystems affected by this patch series (all mm): pagecache, hugetlb,
userfaultfd, vmscan, compaction, migration, cma, ksm, vmstat, mmap,
kconfig, util, memory-hotplug, zswap, zsmalloc, highmem, cleanups, and
kfence"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (143 commits)
kfence: use power-efficient work queue to run delayed work
kfence: maximize allocation wait timeout duration
kfence: await for allocation using wait_event
kfence: zero guard page after out-of-bounds access
mm/process_vm_access.c: remove duplicate include
mm/mempool: minor coding style tweaks
mm/highmem.c: fix coding style issue
btrfs: use memzero_page() instead of open coded kmap pattern
iov_iter: lift memzero_page() to highmem.h
mm/zsmalloc: use BUG_ON instead of if condition followed by BUG.
mm/zswap.c: switch from strlcpy to strscpy
arm64/Kconfig: introduce ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE
x86/Kconfig: introduce ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE
mm,memory_hotplug: add kernel boot option to enable memmap_on_memory
acpi,memhotplug: enable MHP_MEMMAP_ON_MEMORY when supported
mm,memory_hotplug: allocate memmap from the added memory range
mm,memory_hotplug: factor out adjusting present pages into adjust_present_page_count()
mm,memory_hotplug: relax fully spanned sections check
drivers/base/memory: introduce memory_block_{online,offline}
mm/memory_hotplug: remove broken locking of zone PCP structures during hot remove
...
SYS_SUPPORTS_HUGETLBFS config has duplicate definitions on platforms
that subscribe it. Instead, just make it a generic option which can be
selected on applicable platforms.
Also rename it as ARCH_SUPPORTS_HUGETLBFS instead. This reduces code
duplication and makes it cleaner.
Link: https://lkml.kernel.org/r/1617259448-22529-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> [riscv]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "hugetlb: Disable huge pmd unshare for uffd-wp", v4.
This series tries to disable huge pmd unshare of hugetlbfs backed memory
for uffd-wp. Although uffd-wp of hugetlbfs is still during rfc stage,
the idea of this series may be needed for multiple tasks (Axel's uffd
minor fault series, and Mike's soft dirty series), so I picked it out
from the larger series.
This patch (of 4):
It is a preparation work to be able to behave differently in the per
architecture huge_pte_alloc() according to different VMA attributes.
Pass it deeper into huge_pmd_share() so that we can avoid the find_vma() call.
[peterx@redhat.com: build fix]
Link: https://lkml.kernel.org/r/20210304164653.GB397383@xz-x1Link: https://lkml.kernel.org/r/20210218230633.15028-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210218230633.15028-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'cross_compiling' is defined by the top Makefile and available for
arch Makefiles to check whether it is a cross build or not. A good
thing is the variable name 'cross_compiling' is self-documenting.
This is a simple replacement for m68k, mips, sh, for which $(ARCH)
and $(SRCARCH) always match.
No functional change is intended for xtensa, either.
This is rather a fix for parisc because arch/parisc/Makefile defines
UTS_MATCHINE depending on CONFIG_64BIT, therefore cc-cross-prefix
is not working in Kconfig time.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
-----BEGIN PGP SIGNATURE-----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=uCN4
-----END PGP SIGNATURE-----
Merge tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull Landlock LSM from James Morris:
"Add Landlock, a new LSM from Mickaël Salaün.
Briefly, Landlock provides for unprivileged application sandboxing.
From Mickaël's cover letter:
"The goal of Landlock is to enable to restrict ambient rights (e.g.
global filesystem access) for a set of processes. Because Landlock
is a stackable LSM [1], it makes possible to create safe security
sandboxes as new security layers in addition to the existing
system-wide access-controls. This kind of sandbox is expected to
help mitigate the security impact of bugs or unexpected/malicious
behaviors in user-space applications. Landlock empowers any
process, including unprivileged ones, to securely restrict
themselves.
Landlock is inspired by seccomp-bpf but instead of filtering
syscalls and their raw arguments, a Landlock rule can restrict the
use of kernel objects like file hierarchies, according to the
kernel semantic. Landlock also takes inspiration from other OS
sandbox mechanisms: XNU Sandbox, FreeBSD Capsicum or OpenBSD
Pledge/Unveil.
In this current form, Landlock misses some access-control features.
This enables to minimize this patch series and ease review. This
series still addresses multiple use cases, especially with the
combined use of seccomp-bpf: applications with built-in sandboxing,
init systems, security sandbox tools and security-oriented APIs [2]"
The cover letter and v34 posting is here:
https://lore.kernel.org/linux-security-module/20210422154123.13086-1-mic@digikod.net/
See also:
https://landlock.io/
This code has had extensive design discussion and review over several
years"
Link: https://lore.kernel.org/lkml/50db058a-7dde-441b-a7f9-f6837fe8b69f@schaufler-ca.com/ [1]
Link: https://lore.kernel.org/lkml/f646e1c7-33cf-333f-070c-0a40ad0468cd@digikod.net/ [2]
* tag 'landlock_v34' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
landlock: Enable user space to infer supported features
landlock: Add user and kernel documentation
samples/landlock: Add a sandbox manager example
selftests/landlock: Add user space tests
landlock: Add syscall implementations
arch: Wire up Landlock syscalls
fs,security: Add sb_delete hook
landlock: Support filesystem access-control
LSM: Infrastructure management of the superblock
landlock: Add ptrace restrictions
landlock: Set up the security framework and manage credentials
landlock: Add ruleset and domain management
landlock: Add object management
- Stage-2 isolation for the host kernel when running in protected mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation,
zap under read lock, enable/disably dirty page logging under
read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing
the architecture-specific code
- Some selftests improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmCJ13kUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroM1HAgAqzPxEtiTPTFeFJV5cnPPJ3dFoFDK
y/juZJUQ1AOtvuWzzwuf175ewkv9vfmtG6rVohpNSkUlJYeoc6tw7n8BTTzCVC1b
c/4Dnrjeycr6cskYlzaPyV6MSgjSv5gfyj1LA5UEM16LDyekmaynosVWY5wJhju+
Bnyid8l8Utgz+TLLYogfQJQECCrsU0Wm//n+8TWQgLf1uuiwshU5JJe7b43diJrY
+2DX+8p9yWXCTz62sCeDWNahUv8AbXpMeJ8uqZPYcN1P0gSEUGu8xKmLOFf9kR7b
M4U1Gyz8QQbjd2lqnwiWIkvRLX6gyGVbq2zH0QbhUe5gg3qGUX7JjrhdDQ==
=AXUi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
mem_init_print_info() is called in mem_init() on each architecture, and
pass NULL argument, so using void argument and move it into mm_init().
Link: https://lkml.kernel.org/r/20210317015210.33641-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com> [x86]
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr> [powerpc]
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com> [sparc64]
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> [arm]
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page_mapping_file() is only used by some architectures, and then it
is usually only used in one place. Make it a static inline function
so other architectures don't have to carry this dead code.
Link: https://lkml.kernel.org/r/20210317123011.350118-1-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
early_memtest() does not get called from all architectures. Hence
enabling CONFIG_MEMTEST and providing a valid memtest=[1..N] kernel
command line option might not trigger the memory pattern tests as would be
expected in normal circumstances. This situation is misleading.
The change here prevents the above mentioned problem after introducing a
new config option ARCH_USE_MEMTEST that should be subscribed on platforms
that call early_memtest(), in order to enable the config CONFIG_MEMTEST.
Conversely CONFIG_MEMTEST cannot be enabled on platforms where it would
not be tested anyway.
Link: https://lkml.kernel.org/r/1617269193-22294-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> (arm64)
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQJOBAABCAA4FiEEbt46xwy6kEcDOXoUeZbBVTGwZHAFAmCJS6oaHHRzYm9nZW5k
QGFscGhhLmZyYW5rZW4uZGUACgkQeZbBVTGwZHDnbBAAnfVnVgjRZZ1y+oX9siFk
xrQUVJMxEl02272yptB6VtWOLhTnFnJ2xNyjb4EcoCbTiBReSNQ8ee4WYYdCgSXh
soDW6wYrlpcZau5sRg72xybmmYo4aUEh3D9PWNpCaDXFaSpnbXv28ccCTb0yLvCL
4s72wl+hLGAygJMlA6gkQ3mN3XblRk+ci1MLQOr4WpxCmWx0ozKKnHnlt21rw26w
kokJRsqKAOgzzB5LIBgFBdlNKXMd+Xq8BhDXvilNbH2+LtrNIIbyJDPReZBkkO/T
JWGbcNJMox/lBzqtM+eIMvuf/2QHtUAB4xXSAH+oAno6PlV0S73Oo5E+tI++ax9j
WmdN3nwjhpEmwyovZwZtl+b0P14NXXAYKYOYClaRn3dFxEXnS7Fiq+EyGuOEQYBS
oTa2VXQrFZfpN55wtdwmXdwWDwNuE8UtEbkSpblyTw9HQqh3jnl8xKGnaWzw7HMN
D1yycBxMzuOrMiY5UBcfuzdU1K9Dgxn+ur8IfraXjjcEmZB+1TEB74/GCLK1/UJM
lBUrW9ZrE5e3COA/gqPq5ZQf4W9cp8xLBMWWXxnMSBEErpePDtt3EZP2H62sK+3a
wuyvEwRuiFskeUi/Tr7t89u4oXrcIZ7Q3bM3LKj3IWbsk/Znk8X03GCF86QU27zP
wlrVT2ef0/8DHEI7btraCb4=
=w/c4
-----END PGP SIGNATURE-----
Merge tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed get_fs/set_fs
- removed broken/unmaintained MIPS KVM trap and emulate support
- added support for Loongson-2K1000
- fixes and cleanups
* tag 'mips_5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (107 commits)
MIPS: BCM63XX: Use BUG_ON instead of condition followed by BUG.
MIPS: select ARCH_KEEP_MEMBLOCK unconditionally
mips: Do not include hi and lo in clobber list for R6
MIPS:DTS:Correct the license for Loongson-2K
MIPS:DTS:Fix label name and interrupt number of ohci for Loongson-2K
MIPS: Avoid handcoded DIVU in `__div64_32' altogether
lib/math/test_div64: Correct the spelling of "dividend"
lib/math/test_div64: Fix error message formatting
mips/bootinfo:correct some comments of fw_arg
MIPS: Avoid DIVU in `__div64_32' is result would be zero
MIPS: Reinstate platform `__div64_32' handler
div64: Correct inline documentation for `do_div'
lib/math: Add a `do_div' test module
MIPS: Makefile: Replace -pg with CC_FLAGS_FTRACE
MIPS: pci-legacy: revert "use generic pci_enable_resources"
MIPS: Loongson64: Add kexec/kdump support
MIPS: pci-legacy: use generic pci_enable_resources
MIPS: pci-legacy: remove busn_resource field
MIPS: pci-legacy: remove redundant info messages
MIPS: pci-legacy: stop using of_pci_range_to_resource
...
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmCJU1UACgkQnJ2qBz9k
QNk62AgAgp05OIXU/AgObb7DvSyI3ycwCV8PeWBpwD8yoDAh5x0tmT7vnJu974p6
yHdnF7rr69ZzvbNCHLJ5kRykRlUao9W7cO5fdOW1uTpL7Ic60QuJMks/NfgVTHp1
2zIQmBDerfn1/LTK8r2pPGcvtcjRcr7Ep4beN0Duw57lfVMJhjsNRPnBbXGBcp0r
QzKk4/8V3DCZvOw+XNC3nto7avjvf+nU9sJmuh83546eqh0atjWivvO5aAlDOe6W
rhBiLlmP0in5u2n1fYqzI1OQvtgtleyEZT2G0CrbAZn0xjmV/if9wl+3K6TOwDvR
778xDEX7sZCaO/xkB+WK3hrd15ftKg==
=0kYE
-----END PGP SIGNATURE-----
Merge tag 'for_v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull quota, ext2, reiserfs updates from Jan Kara:
- support for path (instead of device) based quotactl syscall
(quotactl_path(2))
- ext2 conversion to kmap_local()
- other minor cleanups & fixes
* tag 'for_v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fs/reiserfs/journal.c: delete useless variables
fs/ext2: Replace kmap() with kmap_local_page()
ext2: Match up ext2_put_page() with ext2_dotdot() and ext2_find_entry()
fs/ext2/: fix misspellings using codespell tool
quota: report warning limits for realtime space quotas
quota: wire up quotactl_path
quota: Add mountpath based quota support
usual suspects are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and
Rockchip, but it feels pretty light on commits. There's only one real commit to
the framework core and that's to consolidate code. Otherwise the diffstat is
dominated by many Qualcomm clk driver patches that modernize the driver for the
proper way of speciying clk parents. That's shifting data around, which could
subtly break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL
-----BEGIN PGP SIGNATURE-----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=z+1G
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Here's a collection of largely clk driver updates. The usual suspects
are here: i.MX, Qualcomm, Renesas, Allwinner, Samsung, and Rockchip,
but it feels pretty light on commits.
There's only one real commit to the framework core and that's to
consolidate code. Otherwise the diffstat is dominated by many Qualcomm
clk driver patches that modernize the driver for the proper way of
speciying clk parents. That's shifting data around, which could subtly
break things so I'll be on the lookout for fixes.
New Drivers:
- Proper clk driver for Mediatek MT7621 SoCs
- Support for the clock controller on the new Rockchip rk3568
Updates:
- Simplify Zynq Kconfig dependencies
- Use clk_hw pointers in socfpga driver
- Cleanup parent data in qcom clk drivers
- Some cleanups for rk3399 modularization
- Fix reparenting of i.MX UART clocks by initializing only the ones
associated to stdout
- Correct the PCIE clocks for i.MX8MP and i.MX8MQ
- Make i.MX LPCG and SCU clocks return on registering failure
- Kernel doc fixes
- Add DAB hardware accelerator clocks on Renesas R-Car E3 and M3-N
- Add timer (TMU) clocks on Renesas R-Car H3 ES1.0
- Add Timer (TMU & CMT) and thermal sensor (TSC) clocks on
Renesas R-Car V3U
- Sigma-delta modulation on Allwinner V3s audio PLL"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (82 commits)
MAINTAINERS: add MT7621 CLOCK maintainer
staging: mt7621-dts: use valid vendor 'mediatek' instead of invalid 'mtk'
staging: mt7621-dts: make use of new 'mt7621-clk'
clk: ralink: add clock driver for mt7621 SoC
clk: uniphier: Fix potential infinite loop
clk: qcom: rpmh: add support for SDX55 rpmh IPA clock
clk: qcom: gcc-sdm845: get rid of the test clock
clk: qcom: convert SDM845 Global Clock Controller to parent_data
dt-bindings: clock: separate SDM845 GCC clock bindings
clk: qcom: apss-ipq-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a53-pll: Add missing MODULE_DEVICE_TABLE
clk: qcom: a7-pll: Add missing MODULE_DEVICE_TABLE
dt: bindings: add mt7621-sysc device tree binding documentation
dt-bindings: clock: add dt binding header for mt7621 clocks
clk: samsung: Remove redundant dev_err calls
clk: zynqmp: pll: add set_pll_mode to check condition in zynqmp_pll_enable
clk: zynqmp: move zynqmp_pll_set_mode out of round_rate callback
clk: zynqmp: Drop dependency on ARCH_ZYNQMP
clk: zynqmp: Enable the driver if ZYNQMP_FIRMWARE is selected
clk: qcom: gcc-sm8350: use ARRAY_SIZE instead of specifying num_parents
...
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can be
cleaned up which either use a seperate mechanism to prevent auto-enable
at request time or have a racy mechanism which disables the interrupt
right after request.
- Get rid of the last usage of irq_create_identity_mapping() and remove
the interface.
- An overhaul of tasklet_disable(). Most usage sites of tasklet_disable()
are in task context and usually in cleanup, teardown code pathes.
tasklet_disable() spinwaits for a tasklet which is currently executed.
That's not only a problem for PREEMPT_RT where this can lead to a live
lock when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs the
tasklet is scheduled out and the disabling code has to spin wait until
it's scheduled back in. Though there are a few code pathes which invoke
tasklet_disable() from non-sleepable context. For these a new disable
variant which still spinwaits is provided which allows to switch
tasklet_disable() to a sleep wait mechanism. For the atomic use cases
this does not solve the live lock issue on PREEMPT_RT. That is mitigated
by blocking on the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in task
context and all interrupt handlers, which are not explicitly marked to
be invoked in hard interrupt context are forced into task context as
well. This allows to protect against softirq processing with a per
CPU lock, which in turn allows to make BH disabled regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions which
provide the context specific functionality. The local_bh_disable() /
local_bh_enable() mechanism are obviously seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=id4G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual updates from the irq departement:
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can
be cleaned up which either use a seperate mechanism to prevent
auto-enable at request time or have a racy mechanism which disables
the interrupt right after request.
- Get rid of the last usage of irq_create_identity_mapping() and
remove the interface.
- An overhaul of tasklet_disable().
Most usage sites of tasklet_disable() are in task context and
usually in cleanup, teardown code pathes. tasklet_disable()
spinwaits for a tasklet which is currently executed. That's not
only a problem for PREEMPT_RT where this can lead to a live lock
when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs
the tasklet is scheduled out and the disabling code has to spin
wait until it's scheduled back in.
There are a few code pathes which invoke tasklet_disable() from
non-sleepable context. For these a new disable variant which still
spinwaits is provided which allows to switch tasklet_disable() to a
sleep wait mechanism. For the atomic use cases this does not solve
the live lock issue on PREEMPT_RT. That is mitigated by blocking on
the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in
task context and all interrupt handlers, which are not explicitly
marked to be invoked in hard interrupt context are forced into task
context as well. This allows to protect against softirq processing
with a per CPU lock, which in turn allows to make BH disabled
regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions
which provide the context specific functionality. The
local_bh_disable() / local_bh_enable() mechanism are obviously
seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt
controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place"
* tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
irqchip/xilinx: Expose Kconfig option for Zynq/ZynqMP
irqchip/gic-v3: Do not enable irqs when handling spurious interrups
dt-bindings: interrupt-controller: Add IDT 79RC3243x Interrupt Controller
irqchip: Add support for IDT 79rc3243x interrupt controller
irqdomain: Drop references to recusive irqdomain setup
irqdomain: Get rid of irq_create_strict_mappings()
irqchip/jcore-aic: Kill use of irq_create_strict_mappings()
ARM: PXA: Kill use of irq_create_strict_mappings()
irqchip/gic-v4.1: Disable vSGI upon (GIC CPUIF < v4.1) detection
irqchip/tb10x: Use 'fallthrough' to eliminate a warning
genirq: Reduce irqdebug cacheline bouncing
kernel: Initialize cpumask before parsing
irqchip/wpcm450: Drop COMPILE_TEST
irqchip/irq-mst: Support polarity configuration
irqchip: Add driver for WPCM450 interrupt controller
dt-bindings: interrupt-controller: Add nuvoton, wpcm450-aic
dt-bindings: qcom,pdc: Add compatible for sc7280
irqchip/stm32: Add usart instances exti direct event support
irqchip/gic-v3: Fix OF_BAD_ADDR error handling
irqchip/sifive-plic: Mark two global variables __ro_after_init
...
Pull crypto updates from Herbert Xu:
"API:
- crypto_destroy_tfm now ignores errors as well as NULL pointers
Algorithms:
- Add explicit curve IDs in ECDH algorithm names
- Add NIST P384 curve parameters
- Add ECDSA
Drivers:
- Add support for Green Sardine in ccp
- Add ecdh/curve25519 to hisilicon/hpre
- Add support for AM64 in sa2ul"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (184 commits)
fsverity: relax build time dependency on CRYPTO_SHA256
fscrypt: relax Kconfig dependencies for crypto API algorithms
crypto: camellia - drop duplicate "depends on CRYPTO"
crypto: s5p-sss - consistently use local 'dev' variable in probe()
crypto: s5p-sss - remove unneeded local variable initialization
crypto: s5p-sss - simplify getting of_device_id match data
ccp: ccp - add support for Green Sardine
crypto: ccp - Make ccp_dev_suspend and ccp_dev_resume void functions
crypto: octeontx2 - add support for OcteonTX2 98xx CPT block.
crypto: chelsio/chcr - Remove useless MODULE_VERSION
crypto: ux500/cryp - Remove duplicate argument
crypto: chelsio - remove unused function
crypto: sa2ul - Add support for AM64
crypto: sa2ul - Support for per channel coherency
dt-bindings: crypto: ti,sa2ul: Add new compatible for AM64
crypto: hisilicon - enable new error types for QM
crypto: hisilicon - add new error type for SEC
crypto: hisilicon - support new error types for ZIP
crypto: hisilicon - dynamic configuration 'err_info'
crypto: doc - fix kernel-doc notation in chacha.c and af_alg.c
...
BUG_ON uses unlikely in if(), it can be optimized at compile time.
Usually, the condition in if() is not satisfied. In my opinion,
this can improve the efficiency of the multi-stage pipeline.
Signed-off-by: zhouchuangao <zhouchuangao@vivo.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
While removing allnoconfig_y from Kconfig, ARCH=mips allnoconfig builds
started failing with the error:
WARNING: modpost: vmlinux.o(.text+0x9c70): Section mismatch in reference
from the function reserve_exception_space() to the function
.meminit.text:memblock_reserve()
The function reserve_exception_space() references the function __meminit
memblock_reserve().
This is often because reserve_exception_space lacks a __meminit
annotation or the annotation of memblock_reserve is wrong.
ERROR: modpost: Section mismatches detected.
Set CONFIG_SECTION_MISMATCH_WARN_ONLY=y to allow them.
allnoconfig disables DEBUG_KERNEL and thus ARCH_KEEP_MEMBLOCK, which
changes __init_memblock to be equivalent to __meminit triggering the
above error.
Link: https://lore.kernel.org/linux-kbuild/20210313194836.372585-11-masahiroy@kernel.org/
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
From [1]
"GCC 10 (PR 91233) won't silently allow registers that are not
architecturally available to be present in the clobber list anymore,
resulting in build failure for mips*r6 targets in form of:
...
.../sysdep.h:146:2: error: the register ‘lo’ cannot be clobbered in ‘asm’ for the current target
146 | __asm__ volatile ( \
| ^~~~~~~
This is because base R6 ISA doesn't define hi and lo registers w/o DSP
extension. This patch provides the alternative clobber list for r6 targets
that won't include those registers."
Since kernel 5.4 and mips support for generic vDSO [2], the kernel fail to
build for mips r6 cpus with gcc 10 for the same reason as glibc.
[1] https://sourceware.org/git/?p=glibc.git;a=commit;h=020b2a97bb15f807c0482f0faee2184ed05bcad8
[2] '24640f233b46 ("mips: Add support for generic vDSO")'
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
make license from GPL3.0 to GPL2.0
Signed-off-by: xiaochuan mao <maoxiaochuan@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
from Loongson-2K1000 user manual know that under pci bus
the device num is 4, function number is 2 and register is 0x2200
is ohci. the ohci interrupt number is 51. because Loongson-2K1000 has
64 interrupt sources, 0-31 correspond to the device tree liointc0 device
node, and the other correspond to liointc1 node. so it should be
number 19 correspon to liointc1.
Signed-off-by: xiaochuan mao <maoxiaochuan@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
from arch/mips/kernel/head.S we know that use a0~a3 for fw_arg0~fw_arg3
there is some code from head.S:
LONG_S a0, fw_arg0 # firmware arguments
LONG_S a1, fw_arg1
LONG_S a2, fw_arg2
LONG_S a3, fw_arg3
Signed-off-by: xiaochuan mao <maoxiaochuan@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.")
Reported-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This patch replaces the "open-coded" -pg compile flag with a CC_FLAGS_FTRACE
makefile variable which architectures can override if a different option
should be used for code generation.
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This mostly reverts commit 99bca615d8 ("MIPS: pci-legacy: use generic
pci_enable_resources"). Fixes regressions such as:
ata_piix 0000:00:0a.1: can't enable device: BAR 0 [io 0x01f0-0x01f7] not
claimed
ata_piix: probe of 0000:00:0a.1 failed with error -22
The only changes from the strict revert are to fix checkpatch errors:
ERROR: spaces required around that '=' (ctx:VxV)
#33: FILE: arch/mips/pci/pci-legacy.c:252:
+ for (idx=0; idx < PCI_NUM_RESOURCES; idx++) {
^
ERROR: do not use assignment in if condition
#67: FILE: arch/mips/pci/pci-legacy.c:284:
+ if ((err = pcibios_enable_resources(dev, mask)) < 0)
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
If there is no mac address passed via platform data try to get it via
device tree and fall back to a random mac address, if all fail.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of access to struct korina_device by just passing the mac
address via platform data and use drvdata for passing netdev to remove
function.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yank out the hva-based MMU notifier APIs now that all architectures that
use the notifiers have moved to the gfn-based APIs.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move MIPS to the gfn-based MMU notifier APIs, which do the hva->gfn
lookup in common code, and whose code is nearly identical to MIPS'
lookup.
No meaningful functional change intended, though the exact order of
operations is slightly different since the memslot lookups occur before
calling into arch code.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return 1 from kvm_unmap_hva_range and kvm_set_spte_hva if a flush is
needed, so that the generic code can coalesce the flushes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since all calls to kvm_flush_remote_tlbs must be preceded by
kvm_mips_callbacks->prepare_flush_shadow, repurpose
kvm_arch_flush_remote_tlb to invoke it. This makes it possible
to use the TLB flushing mechanism provided by the generic MMU
notifier code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Both trap-and-emulate and VZ have a single implementation that covers
both .flush_shadow_all and .flush_shadow_memslot, and both of them end
with a call to kvm_flush_remote_tlbs.
Unify the callbacks into one and extract the call to kvm_flush_remote_tlbs.
The next patches will pull it further out of the the architecture-specific
MMU notifier functions kvm_unmap_hva_range and kvm_set_spte_hva.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the prototypes for the MMU notifier callbacks out of arch code and
into common code. There is no benefit to having each arch replicate the
prototypes since any deviation from the invocation in common code will
explode.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210326021957.1424875-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add kexec/kdump support for Loongson64 by:
1, Provide Loongson-specific kexec functions: loongson_kexec_prepare(),
loongson_kexec_shutdown() and loongson_crash_shutdown();
2, Provide Loongson-specific assembly code in kexec_smp_wait();
To start Loongson64, The boot CPU needs 3 parameters:
fw_arg0: the number of arguments in cmdline (i.e., argc).
fw_arg1: structure holds cmdline such as "root=/dev/sda1 console=tty"
(i.e., argv).
fw_arg2: environment (i.e., envp, additional boot parameters from LEFI).
Non-boot CPUs do not need one parameter as the IPI mailbox base address.
They query their own IPI mailbox to get PC, SP and GP in a loopi, until
the boot CPU brings them up.
loongson_kexec_prepare(): Setup cmdline for kexec/kdump. The kexec/kdump
cmdline comes from kexec's "append" option string. This structure will
be parsed in fw_init_cmdline() of arch/mips/fw/lib/cmdline.c. Both image
->control_code_page and the cmdline need to be in a safe memory region
(memory allocated by the old kernel may be corrupted by the new kernel).
In order to maintain compatibility for the old firmware, the low 2MB is
reserverd and safe for Loongson. So let KEXEC_CTRL_CODE and KEXEC_ARGV_
ADDR be here. LEFI parameters may be corrupted at runtime, so backup it
at mips_reboot_setup(), and then restore it at loongson_kexec_shutdown()
/loongson_crash_shutdown().
loongson_kexec_shutdown(): Wake up all present CPUs and let them go to
reboot_code_buffer. Pass the kexec parameters to kexec_args.
loongson_crash_shutdown(): Pass the kdump parameters to kexec_args.
The assembly part in kexec_smp_wait provide a routine as BIOS does, in
order to keep secondary CPUs in a querying loop.
The layout of low 2MB memory in our design:
0x80000000, the first MB, the first 64K, Exception vectors
0x80010000, the first MB, the second 64K, STR (suspend) data
0x80020000, the first MB, the third and fourth 64K, UEFI HOB
0x80040000, the first MB, the fifth 64K, RT-Thread for SMC
0x80100000, the second MB, the first 64K, KEXEC code
0x80108000, the second MB, the second 64K, KEXEC data
Cc: Eric Biederman <ebiederm@xmission.com>
Tested-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Follow the reasoning from commit 842de40d93 ("PCI: add generic
pci_enable_resources()"):
The only functional difference from the MIPS version is that the
generic one uses "!r->parent" to check for resource collisions
instead of "!r->start && r->end".
That should have no effect on any pci-legacy driver.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
