MMU SCRATCH_DATA0 register is intended to cache task pgd. However in
ARC700 SMP port, it has to be repurposed for re-entrant interrupt
handling, while UP port doesn't. We currently handle these use-cases
using a fabricated #define which has usual issues of dependency nesting
and obvious ugliness.
So clean this up: for ARC700 don't use to cache pgd (even in UP) and do
the opposite for ARCv2.
And while here, switch to canonical pgd_offset().
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
NPS customers are no longer doing active development, as evident from
rand config build failures reported in recent times, so drop support
for NPS platform.
Tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC700 exception (and intr handling) didn't have auto stack switching
thus had to rely on stashing a reg temporarily (to free it up) at a
known place in memory, allowing to code up the low level stack switching.
This however was not re-entrant in SMP which thus had to repurpose the
per-cpu MMU SCRATCH DATA register otherwise used to "cache" the task pdg
pointer (vs. reading it from mm struct)
The newer HS cores do have auto-stack switching and thus even SMP builds
can use the MMU SCRATCH reg as originally intended.
This patch fixes the restriction to ARC700 SMP builds only
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preserve eflags and gpa1 aux during entry/exit into kernel as these
could be modified by kernel mode
These registers used by compare exchange instructions.
- GPA1 is used for compare value,
- EFLAGS got bit reflects atomic operation response.
EFLAGS is zeroed for each new user task so it won't get its
parent value.
Signed-off-by: Liav Rehana <liavr@mellanox.com>
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With generic "identity" num of CPUs is limited to 256 (8 bit).
We use our alternative AUX register GLOBAL_ID (12 bit).
Now we can support up to 4096 CPUs.
Signed-off-by: Noam Camus <noamc@ezchip.com>
The requirement is to
- Reenable Exceptions (AE cleared)
- Reenable Interrupts (E1/E2 set)
We need to do wiggle these bits into ERSTATUS and call RTIE.
Prev version used the pre-exception STATUS32 as starting point for what
goes into ERSTATUS. This required explicit fixups of U/DE/L bits.
Instead, use the current (in-exception) STATUS32 as starting point.
Being in exception handler U/DE/L can be safely assumed to be correct.
Only AE/E1/E2 need to be fixed.
So the new implementation is slightly better
-Avoids read form memory
-Is 4 bytes smaller for the typical 1 level of intr configuration
-Depicts the semantics more clearly
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Previously this macro was overloaded with stack switching, saving SP at right
slot in pt_regs, saving/setup of r25 and setting SP baseline to where
pt_regs->sp is saved (vs. bottom of pt_regs)
Now it only does SP switch, and leaves SP pointing to bottom of pt_regs.
r25 saving is no longer done here to allow for future reordering of
regfile in pt_regs w/o touching this macro
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler
ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
