We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Let drivers advertise support for AP-mode SAE authentication offload
with a new NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Link: https://lore.kernel.org/r/20200817073316.33402-4-stanley.hsu@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to reuse the attributes for other counters such as BSS color
change. Rename them to more generic names.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200811080107.3615705-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the nl80211 structs, definitions, policies and parsing
code required to pass fixed HE rate, GI and LTF settings.
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200804081630.2013619-1-john@phrozen.org
[fix comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some usable channels are located in the union of adjacent
regulatory rules, for example channel 144 in Germany.
Enable them, by also checking if a channel spans two adjacent
regulatory rules/frequency ranges.
All flags involved are disabling things, therefore we can build
the maximum by or-ing them together. Furthermore, take the maximum
of DFS CAC time values and the minimum of allowed power of both
adjacent channels in order to comply with both regulatory rules at
the same time.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200803144353.305538-2-markus.theil@tu-ilmenau.de
[remove unrelated comment changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a preparation to handle adjacent rule channels,
factor out handling channels located in a single
regulatory rule.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200803144353.305538-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a few attributes with minimum and maximum lengths that are
not the same, use the new feature of being able to specify both in
the policy to validate them, removing code and allowing this to be
advertised to userspace in the policy export.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200819085642.8f12ffa14f33.I9d948d59870e521febcd79bb4a986b1de1dca47b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust the 6 GHz frequency to channel conversion function,
the other way around was previously handled.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Link: https://lore.kernel.org/r/1592599921-10607-1-git-send-email-asinghal@codeaurora.org
[rewrite commit message, hard-code channel 2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix cfg80211_chandef_usable():
consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz.
Based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com
[reformat the code a bit and use u32_get_bits()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change places that open-code NLA_POLICY_MIN_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change places that open-code NLA_POLICY_EXACT_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let drivers advertise support for AP-mode WPA/WPA2-PSK 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_START_AP command, and contain the PSK (which is
the PMK, hence the name).
The driver is assumed to handle the 4-way handshake by itself in this
case, instead of relying on userspace.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Link: https://lore.kernel.org/r/20200623134938.39997-2-chi-hsien.lin@cypress.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200611140238.427461-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20200625111524.3992-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Re-write the end of 'nl80211_trigger_scan()' with a more standard, easy to
understand and future proof version.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173551.274448-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 5fe231e873 ("cfg80211: vastly simplify locking"), the
'unlock' label at the end of 'nl80211_trigger_scan()' is useless and
misleading, because nothing is unlocked there.
Direct return can be used instead of 'err = -<error code>; goto unlock;'
construction.
Remove this label and simplify code accordingly.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200712173539.274395-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211 vendor netlink dumpit, like netlink_callback->dump, should
signal successful completion by returning 0.
Currently, that will just cause dumpit to be called again, possibly
many times until an error occurs. Since skb->len is never going to be
0 by the time dumpit is called, the only way for dumpit to signal
completion is by returning an error. If it returns a positive value,
the current message is cancelled, but that positive value is returned
and nl80211_vendor_cmd_dump gets called again.
Fix that by passing a return value of 0 through.
Signed-off-by: Julian Squires <julian@cipht.net>
Link: https://lore.kernel.org/r/20200720145033.401307-1-julian@cipht.net
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the case where a vendor command does not implement doit, and has no
flags set, doit would not be validated and a NULL pointer dereference
would occur, for example when invoking the vendor command via iw.
I encountered this while developing new vendor commands. Perhaps in
practice it is advisable to always implement doit along with dumpit,
but it seems reasonable to me to always check doit anyway, not just
when NEED_WDEV.
Signed-off-by: Julian Squires <julian@cipht.net>
Link: https://lore.kernel.org/r/20200706211353.2366470-1-julian@cipht.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simple fixes which require no deep knowledge of the code.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In the files:
- net/mac80211/rx.c
- net/wireless/Kconfig
the wiki url is still the old "wireless.kernel.org"
instead of the new "wireless.wiki.kernel.org"
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Link: https://lore.kernel.org/r/20200605154112.16277-10-f.suligoi@asem.it
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lockdep reports that we may deadlock because we take the RTNL on
the work struct, but flush it under RTNL. Clearly, it's correct.
In practice, this can happen when doing rfkill on an active device.
Fix this by moving the work struct to the wiphy (registered dev)
layer, and iterate over all the wdevs inside there. This then
means we need to track which one of them has work to do, so we
don't update to the driver for all wdevs all the time.
Also fix a locking bug I noticed while working on this - the
registrations list is iterated as if it was an RCU list, but it
isn't handle that way - and we need to lock now for the update
flag anyway, so remove the RCU.
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Reported-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-and-tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200604120420.b1dc540a7e26.I55dcca56bb5bdc5d7ad66a36a0b42afd7034d8be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
With some newer AKMs, the KCK and KEK are bigger, so allow that
if the driver advertises support for it. In addition, add a new
attribute for the AKM so we can use it for offloaded rekeying.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
[reword commit message]
Link: https://lore.kernel.org/r/20200528212237.5eb58b00a5d1.I61b09d77c4f382e8d58a05dcca78096e99a6bc15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a 6 GHz channel exists, then we can probably safely assume that
the device actually supports it, and then it should support most
bandwidths.
This will probably need to be extended to check the interface type
and then dig into the HE capabilities for that though, to have the
correct bandwidth check.
Link: https://lore.kernel.org/r/20200528213443.d4864ef52e92.I82f09b2b14a56413ce20376d09967fe954a033eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These capabilities cover what would otherwise be transported
in HT/VHT capabilities, but only a subset thereof that is
actually needed on 6 GHz with HE already present. Expose the
capabilities to userspace, drivers are expected to set them
as using the 6 GHz band (currently) requires HE capability.
Link: https://lore.kernel.org/r/20200528213443.244cd5cb9db8.Icd8c773277a88c837e7e3af1d4d1013cc3b66543@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
