* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
Commit d40f0b6f2e instroduced last_cs_enable to avoid setting
chipselect if it's not necessary, but it also introduces a bug. The
chipselect may not be set correctly on multi-device SPI busses. The
reason is that we can't judge the chipselect by bool last_cs_enable,
since chipselect may be modified after other devices were accessed.
So we should record the specific state of chipselect in case of
confusion.
Signed-off-by: Yun Zhou <yun.zhou@windriver.com>
Link: https://lore.kernel.org/r/20220217141234.72737-1-yun.zhou@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers using GPIOs as chip select have been rewritten to use
GPIO descriptors passing the ->use_gpio_descriptors flag. Retire
the code and fields used by the legacy GPIO API.
Do not drop the ->use_gpio_descriptors flag: it now only indicates
that we want to use GPIOs in addition to native chip selects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220210231954.807904-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Soon the SPI-NAND core will need a way to request a SPI controller to
enable ECC support for a given operation. This is because of the
pipelined integration of certain ECC engines, which are directly managed
by the SPI controller itself.
Introduce a spi_mem_op additional field for this purpose: ecc.
So far this field is left unset and checked to be false by all
the SPI controller drivers in their ->supports_op() hook, as they all
call spi_mem_default_supports_op().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-7-miquel.raynal@bootlin.com
Now that spi_mem_default_supports_op() has access to the static
controller capabilities (relating to memory operations), and now that
these capabilities have been filled by the relevant controllers, there
is no need for a specific helper checking only DTR operations, so let's
just kill spi_mem_dtr_supports_op() and simply use
spi_mem_default_supports_op() instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-6-miquel.raynal@bootlin.com
Create a spi_controller_mem_caps structure and put it within the
spi_controller structure close to the spi_controller_mem_ops
strucure. So far the only field in this structure is the support for dtr
operations, but soon we will add another parameter.
Also create a helper to parse the capabilities and check if the
requested capability has been set or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-2-miquel.raynal@bootlin.com
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
this series goal is to change the spi remove callback's return value to void.
After numerous patches nearly all drivers already return 0 unconditionally.
The four first patches in this series convert the remaining three drivers to
return 0, the final patch changes the remove prototype and converts all
implementers.
base-commit: 26291c54e1
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
This series enhances the helpers for ACPI resources to cope with
multiple resources and exports them for use in the x86 platform code's
multi-instantiate driver.
Some ACPI nodes may have more than one Spi Resource.
To be able to handle these case, its necessary to have
a way of counting these resources.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-5-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a node contains more than one SPI resource it may be necessary to
use an index to select which one you want to allocate a spi device for.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This can then be used to find a spi resource inside an
ACPI node, and allocate a spi device.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-3-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This functions were previously made private since they
were not used. However, these functions will be needed
again.
Partial revert of commit da21fde0fd
("spi: Make several public functions private to spi.c")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220121172431.6876-2-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the PXA2xx SPI driver to use GPIO descriptors
exclusively to retrieve GPIO chip select lines.
The device tree and ACPI paths of the driver already use
descriptors, hence ->use_gpio_descriptors is already set and
this codepath is well tested.
Convert all the PXA boards providing chip select GPIOs as
platform data and drop the old GPIO chipselect handling in
favor of the core managing it exclusively.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220125005836.494807-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has a bunch of custom oldstyle GPIO number-passing
fields and a custom set-up callback.
The good thing is: nothing in the kernel is using it.
Convert the driver to use GPIO descriptors with a SPI_MASTER_GPIO_SS
flag so that the local CS callback also get invoked as the hardware
needs this.
New users of this driver can provide GPIO descriptor tables like
the other converted drivers.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220119000914.192553-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit b42faeee71 ("spi: Add a PTP system timestamp
to the transfer structure") added an include of ptp_clock_kernel.h
to spi.h for struct ptp_system_timestamp but a forward declaration
is enough. Let's use that to limit the number of objects we have
to rebuild every time we touch networking headers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210904013140.2377609-1-kuba@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no user of the enable_loopback member in the struct pxa2xx_spi_chip.
Remote this legacy member completely.
The mentioned in the documentation the testing phase can be performed with
spidev_test tool.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211123192723.44537-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull input updates from Dmitry Torokhov:
"Just one new driver (Cypress StreetFighter touchkey), and no input
core changes this time.
Plus various fixes and enhancements to existing drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: iforce - fix control-message timeout
Input: wacom_i2c - use macros for the bit masks
Input: ili210x - reduce sample period to 15ms
Input: ili210x - improve polled sample spacing
Input: ili210x - special case ili251x sample read out
Input: elantench - fix misreporting trackpoint coordinates
Input: synaptics-rmi4 - Fix device hierarchy
Input: i8042 - Add quirk for Fujitsu Lifebook T725
Input: cap11xx - add support for cap1206
Input: remove unused header <linux/input/cy8ctmg110_pdata.h>
Input: ili210x - add ili251x firmware update support
Input: ili210x - export ili251x version details via sysfs
Input: ili210x - use resolution from ili251x firmware
Input: pm8941-pwrkey - respect reboot_mode for warm reset
reboot: export symbol 'reboot_mode'
Input: max77693-haptic - drop unneeded MODULE_ALIAS
Input: cpcap-pwrbutton - do not set input parent explicitly
Input: max8925_onkey - don't mark comment as kernel-doc
Input: ads7846 - do not attempt IRQ workaround when deferring probe
Input: ads7846 - use input_set_capability()
...
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead of
accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom interrupt
code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force one interrupt
per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups
-----BEGIN PGP SIGNATURE-----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=mKh0
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, new features in others and some cleanups
all over the place.
Nothing really stands out and it is all relatively small.
- new driver: gpio-modepin (plus relevant change in zynqmp firmware)
- add interrupt support to gpio-virtio
- enable the 'gpio-line-names' property in the DT bindings for
gpio-rockchip
- use the subsystem helpers where applicable in gpio-uniphier instead
of accessing IRQ structures directly
- code shrink in gpio-xilinx
- add interrupt to gpio-mlxbf2 (and include the removal of custom
interrupt code from the mellanox ethernet driver)
- support multiple interrupts per bank in gpio-tegra186 (and force
one interrupt per bank in older models)
- fix GPIO line IRQ offset calculation in gpio-realtek-otto
- drop unneeded MODULE_ALIAS expansions in multiple drivers
- code cleanup in gpio-aggregator
- minor improvements in gpio-max730x and gpio-mc33880
- Kconfig cleanups"
* tag 'gpio-updates-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
virtio_gpio: drop packed attribute
gpio: virtio: Add IRQ support
gpio: realtek-otto: fix GPIO line IRQ offset
gpio: clean up Kconfig file
net: mellanox: mlxbf_gige: Replace non-standard interrupt handling
gpio: mlxbf2: Introduce IRQ support
gpio: mc33880: Drop if with an always false condition
gpio: max730x: Make __max730x_remove() return void
gpio: aggregator: Wrap access to gpiochip_fwd.tmp[]
gpio: modepin: Add driver support for modepin GPIO controller
dt-bindings: gpio: zynqmp: Add binding documentation for modepin
firmware: zynqmp: Add MMIO read and write support for PS_MODE pin
gpio: tps65218: drop unneeded MODULE_ALIAS
gpio: max77620: drop unneeded MODULE_ALIAS
gpio: xilinx: simplify getting .driver_data
gpio: tegra186: Support multiple interrupts per bank
gpio: tegra186: Force one interrupt per bank
gpio: uniphier: Use helper functions to get private data from IRQ data
gpio: uniphier: Use helper function to get IRQ hardware number
dt-bindings: gpio: add gpio-line-names to rockchip,gpio-bank.yaml
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi or i2c remove callback is only called for devices that probed
successfully. In this case this implies that __max730x_probe() set a
non-NULL driver data. So the check ts == NULL is never true. With this
check dropped, __max730x_remove() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
All these functions have no callers apart from drivers/spi/spi.c. So
drop their declarations in include/linux/spi/spi.h and don't export
them.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211007121415.2401638-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The functions in the platform data struct to initialize, cleanup and
apply custom filters are not in use by any mainline board.
Remove support for them to pave the road for more cleanups to come.
The enum was moved as it has no users outside of the driver code
itself.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210907200726.2034962-3-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the driver
and use generic device property interfaces, improve property sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO banks
per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent within its
header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers
-----BEGIN PGP SIGNATURE-----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=y/RY
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We mostly have various improvements and refactoring all over the place
but also some interesting new features - like the virtio GPIO driver
that allows guest VMs to use host's GPIOs. We also have a new/old GPIO
driver for rockchip - this one has been split out of the pinctrl
driver.
Summary:
- new driver: gpio-virtio allowing a guest VM running linux to access
GPIO lines provided by the host
- split the GPIO driver out of the rockchip pin control driver
- add support for a new model to gpio-aspeed-sgpio, refactor the
driver and use generic device property interfaces, improve property
sanitization
- add ACPI support to gpio-tegra186
- improve the code setting the line names to support multiple GPIO
banks per device
- constify a bunch of OF functions in the core GPIO code and make the
declaration for one of the core OF functions we use consistent
within its header
- use software nodes in intel_quark_i2c_gpio
- add support for the gpio-line-names property in gpio-mt7621
- use the standard GPIO function for setting the GPIO names in
gpio-brcmstb
- fix a bunch of leaks and other bugs in gpio-mpc8xxx
- use generic pm callbacks in gpio-ml-ioh
- improve resource management and PM handling in gpio-mlxbf2
- modernize and improve the gpio-dwapb driver
- coding style improvements in gpio-rcar
- documentation fixes and improvements
- update the MAINTAINERS entry for gpio-zynq
- minor tweaks in several drivers"
* tag 'gpio-updates-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (35 commits)
gpio: mpc8xxx: Use 'devm_gpiochip_add_data()' to simplify the code and avoid a leak
gpio: mpc8xxx: Fix a potential double iounmap call in 'mpc8xxx_probe()'
gpio: mpc8xxx: Fix a resources leak in the error handling path of 'mpc8xxx_probe()'
gpio: viperboard: remove platform_set_drvdata() call in probe
gpio: virtio: Add missing mailings lists in MAINTAINERS entry
gpio: virtio: Fix sparse warnings
gpio: remove the obsolete MX35 3DS BOARD MC9S08DZ60 GPIO functions
gpio: max730x: Use the right include
gpio: Add virtio-gpio driver
gpio: mlxbf2: Use DEFINE_RES_MEM_NAMED() helper macro
gpio: mlxbf2: Use devm_platform_ioremap_resource()
gpio: mlxbf2: Drop wrong use of ACPI_PTR()
gpio: mlxbf2: Convert to device PM ops
gpio: dwapb: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert GPIO to use software nodes
gpio: dwapb: Read GPIO base from gpio-base property
gpio: dwapb: Unify ACPI enumeration checks in get_irq() and configure_irqs()
gpiolib: Deduplicate forward declaration in the consumer.h header
MAINTAINERS: update gpio-zynq.yaml reference
gpio: tegra186: Add ACPI support
...
<linux/spi/max7301.h> despite the placement of the header, is
used by drivers/gpio/gpio-max730*.
The include needs struct gpio_chip and needs to include
<linux/gpio/driver.h> not the legacy <linux/gpio.h> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This patch modified set_cs_timing parameter, no need pass in spi_delay
to set_cs_timing callback.
By the way, we modified the mediatek and tegra114 spi driver to fix build err.
In mediatek spi driver, We have support set absolute time not clk_count,
and call this function in prepare_message not user's API.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133746.6742-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As we know, spi core layer has removed spi_set_cs_timing() API.
So this patch moved spi_delay for cs_timing from spi_controller
to spi_device, because cs timing should be set by spi_device but
not controller.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210804133716.32040-1-Mason.Zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warning in spi.h by adding the missing kernel-doc entry
and also correct the original comment so that they both indicate the
correct polarity of the flag.
../include/linux/spi/spi.h:673: warning: Function parameter or member 'devm_allocated' not described in 'spi_controller'
Fixes: 794aaf0144 ("spi: Fix use-after-free with devm_spi_alloc_*")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: William A. Kennington III <wak@google.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20210628210520.5712-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers like qcom geni need the parent device to be used for
dma mapping, so add a dma_map_dev field and let drivers fill this to be
used as mapping device
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210625052213.32260-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce support for ancillary devices, similar to existing
implementation for I2C. This is useful for devices having
multiple chip-selects, for example some microcontrollers
provide a normal SPI interface and a flashing SPI interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-2-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No one seems to be using this global and exported function, so remove it
as it is no longer needed.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210609071918.2852069-1-gregkh@linuxfoundation.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.
Changes in v5:
- Update spi_mem_read_status() description.
- Update poll_status() description API by indicating that data buffer is
filled with last status value.
- Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
- Remove parenthesys arount -EINVAL in spi_mem_poll_status().
- Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
- Add Boris Reviewed-by for patch 1 and 2.
Changes in v4:
- Remove init_completion() from spi_mem_probe() added in v2.
- Add missing static for spi_mem_read_status().
- Check if operation in spi_mem_poll_status() is a READ.
- Update patch 2 commit message.
- Add comment which explains how delays has been calculated.
- Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.
Chnages in v3:
- Add spi_mem_read_status() which allows to read 8 or 16 bits status.
- Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
and also to poll_status() callback.
- Move spi_mem_supports_op() in SW-based polling case.
- Add delay before invoquing read_poll_timeout().
- Remove the reinit/wait_for_completion() added in v2.
- Add initial_delay_us and polling_delay_us parameters to spinand_wait().
- Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
- Remove spi_mem_finalize_op() API added in v2.
Changes in v2:
- Indicates the spi_mem_poll_status() timeout unit
- Use 2-byte wide status register
- Add spi_mem_supports_op() call in spi_mem_poll_status()
- Add completion management in spi_mem_poll_status()
- Add offload/non-offload case management in spi_mem_poll_status()
- Optimize the non-offload case by using read_poll_timeout()
- mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
- Make usage of new spi_mem_finalize_op() API in
stm32_qspi_wait_poll_status()
Patrice Chotard (3):
spi: spi-mem: add automatic poll status functions
mtd: spinand: use the spi-mem poll status APIs
spi: stm32-qspi: add automatic poll status feature
drivers/mtd/nand/spi/core.c | 45 +++++++++++++------
drivers/spi/spi-mem.c | 86 ++++++++++++++++++++++++++++++++++++
drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
include/linux/mtd/spinand.h | 22 +++++++++
include/linux/spi/spi-mem.h | 16 +++++++
5 files changed, 234 insertions(+), 21 deletions(-)
base-commit: 6efb943b86
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
With STM32 QSPI, it is possible to poll the status register of the device.
This could be done to offload the CPU during an operation (erase or
program a SPI NAND for example).
spi_mem_poll_status API has been added to handle this feature.
This new function take care of the offload/non-offload cases.
For the non-offload case, use read_poll_timeout() to poll the status in
order to release CPU during this phase.
For example, previously, when erasing large area, in non-offload case,
CPU load can reach ~50%, now it decrease to ~35%.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/r/20210518162754.15940-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
While fixing undefined behaviour the commit f60d7270c8 ("spi: Avoid
undefined behaviour when counting unused native CSs") missed the case
when all CSs are GPIOs and thus unused_native_cs will be evaluated to
-1 in unsigned representation. This will falsely trigger a condition
in the spi_get_gpio_descs().
Switch to signed types for *_native_cs SPI controller fields to fix above.
Fixes: f60d7270c8 ("spi: Avoid undefined behaviour when counting unused native CSs")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510131242.49455-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The two headers have quite different ifdeffery to prevent multiple inclusion.
Unify them with the pattern that in particular reflects their location.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the data structure is only referred by pointer, compiler may not need
to see the contents of the data type. Thus, we may replace header inclusions
by respective forward declarations. Due to above add missed headers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups.
-----BEGIN PGP SIGNATURE-----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=WL87
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- Fix hanging on I/O during system suspend for removable cards
- Set read only for SD cards with permanent write protect bit
- Power cycle the SD/SDIO card if CMD11 fails for UHS voltage
- Issue a cache flush for eMMC only when it's enabled
- Adopt to updated cache ctrl settings for eMMC from MMC ioctls
- Use use device property API when parsing voltages
- Don't retry eMMC sanitize cmds
- Use the timeout from the MMC ioctl for eMMC santize cmds
MMC host:
- mmc_spi: Make of_mmc_spi.c resource provider agnostic
- mmc_spi: Use polling for card detect even without voltage-ranges
- sdhci: Check for reset prior to DMA address unmap
- sdhci-acpi: Add support for the AMDI0041 eMMC controller variant
- sdhci-esdhc-imx: Depending on OF Kconfig and cleanup code
- sdhci-pci: Add PCI IDs for Intel LKF
- sdhci-pci: Fix initialization of some SD cards for Intel BYT
- sdhci-pci-gli: Various improvements for GL97xx variants
- sdhci-of-dwcmshc: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- sdhci-of-dwcmshc: Add ACPI support for BlueField-3 SoC
- sdhci-of-dwcmshc: Add Rockchip platform support
- tmio/renesas_sdhi: Extend support for reset and use a reset controller
- tmio/renesas_sdhi: Enable support for MMC_CAP_WAIT_WHILE_BUSY
- tmio/renesas_sdhi: Various improvements
MEMSTICK:
- Minor improvements/cleanups"
* tag 'mmc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (79 commits)
mmc: block: Issue a cache flush only when it's enabled
memstick: r592: ignore kfifo_out() return code again
mmc: block: Update ext_csd.cache_ctrl if it was written
mmc: mmc_spi: Make of_mmc_spi.c resource provider agnostic
mmc: mmc_spi: Use already parsed IRQ
mmc: mmc_spi: Drop unused NO_IRQ definition
mmc: mmc_spi: Set up polling even if voltage-ranges is not present
mmc: core: Convert mmc_of_parse_voltage() to use device property API
mmc: core: Correct descriptions in mmc_of_parse()
mmc: dw_mmc-rockchip: Just set default sample value for legacy mode
mmc: sdhci-s3c: constify uses of driver/match data
mmc: sdhci-s3c: correct kerneldoc of sdhci_s3c_drv_data
mmc: sdhci-s3c: simplify getting of_device_id match data
mmc: tmio: always restore irq register
mmc: sdhci-pci-gli: Enlarge ASPM L1 entry delay of GL975x
mmc: core: Let eMMC sanitize not retry in case of timeout/failure
mmc: core: Add a retries parameter to __mmc_switch function
memstick: r592: remove unused variable
mmc: sdhci-st: Remove unnecessary error log
mmc: sdhci-msm: Remove unnecessary error log
...
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct spi_transfer is declared twice. One is declared at 24th line.
The blew one is not needed though. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210401065904.994121-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
The older API used to supply additional device properties for the
devices - so mainly the function device_add_properties() - is going to
be removed. The reason why the API will be removed is because it gives
false impression that the properties are assigned directly to the
devices, which has actually never been the case - the properties have
always been assigned to a software fwnode which was then just directly
linked with the device when the old API was used. By only accepting
device properties instead of complete software nodes, the subsystems
remove any change of taking advantage of the other features the
software nodes have.
The change that is required from the spi subsystem and the drivers is
trivial. Basically only the "properties" member in struct
spi_board_info, which was a pointer to struct property_entry, is
replaced with a pointer to a complete software node.
thanks,
Heikki Krogerus (4):
spi: Add support for software nodes
ARM: pxa: icontrol: Constify the software node
ARM: pxa: zeus: Constify the software node
spi: Remove support for dangling device properties
arch/arm/mach-pxa/icontrol.c | 12 ++++++++----
arch/arm/mach-pxa/zeus.c | 6 +++++-
drivers/spi/spi.c | 21 ++++++---------------
include/linux/spi/spi.h | 7 +++----
4 files changed, 22 insertions(+), 24 deletions(-)
--
2.30.1
base-commit: a38fd87484
