Introduce pacing of traffic so that the Tx thread can never send more
packets than the receiver has processed plus the number of packets it
can have in its umem. So at any point in time, the number of in flight
packets (not processed by the Rx thread) are less than or equal to the
number of packets that can be held in the Rx thread's umem.
The batch size is also increased to improve running time.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-11-magnus.karlsson@gmail.com
The socket creation retry unnecessarily registered the umem once for
every retry. No reason to do this. It wastes memory and it might lead
to too many pages being locked at some point and the failure of a
test.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-10-magnus.karlsson@gmail.com
Fix a problem where the fill ring was populated with too many
entries. If number of buffers in the umem was smaller than the fill
ring size, the code used to loop over from the beginning of the umem
and start putting the same buffers in again. This is racy indeed as a
later packet can be received overwriting an earlier one before the Rx
thread manages to validate it.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-9-magnus.karlsson@gmail.com
Fix missing initialization of the member rx_pkt_nb in the packet
stream. This leads to some tests declaring success too early as the
test thought all packets had already been received.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-8-magnus.karlsson@gmail.com
Optimize for the aligned case by precomputing the parameter values of
the xdp_buff_xsk and xdp_buff structures in the heads array. We can do
this as the heads array size is equal to the number of chunks in the
umem for the aligned case. Then every entry in this array will reflect
a certain chunk/frame and can therefore be prepopulated with the
correct values and we can drop the use of the free_heads stack. Note
that it is not possible to allocate more buffers than what has been
allocated in the aligned case since each chunk can only contain a
single buffer.
We can unfortunately not do this in the unaligned case as one chunk
might contain multiple buffers. In this case, we keep the old scheme
of populating a heads entry every time it is used and using
the free_heads stack.
Also move xp_release() and xp_get_handle() to xsk_buff_pool.h. They
were for some reason in xsk.c even though they are buffer pool
operations.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-7-magnus.karlsson@gmail.com
Use the new xsk batched rx allocation interface for the zero-copy data
path. As the array of struct xdp_buff pointers kept by the driver is
really a ring that wraps, the allocation routine is modified to detect
a wrap and in that case call the allocation function twice. The
allocation function cannot deal with wrapped rings, only arrays. As we
now know exactly how many buffers we get and that there is no
wrapping, the allocation function can be simplified even more as all
if-statements in the allocation loop can be removed, improving
performance.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-6-magnus.karlsson@gmail.com
Use the new xsk batched rx allocation interface for the zero-copy data
path. As the array of struct xdp_buff pointers kept by the driver is
really a ring that wraps, the allocation routine is modified to detect
a wrap and in that case call the allocation function twice. The
allocation function cannot deal with wrapped rings, only arrays. As we
now know exactly how many buffers we get and that there is no
wrapping, the allocation function can be simplified even more as all
if-statements in the allocation loop can be removed, improving
performance.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-5-magnus.karlsson@gmail.com
In order to use the new xsk batched buffer allocation interface, a
pointer to an array of struct xsk_buff pointers need to be provided so
that the function can put the result of the allocation there. In the
ice driver, we already have a ring that stores pointers to
xdp_buffs. This is only used for the xsk zero-copy driver and is a
union with the structure that is used for the regular non zero-copy
path. Unfortunately, that structure is larger than the xdp_buffs
pointers which mean that there will be a stride (of 20 bytes) between
each xdp_buff pointer. And feeding this into the xsk_buff_alloc_batch
interface will not work since it assumes a regular array of xdp_buff
pointers (each 8 bytes with 0 bytes in-between them on a 64-bit
system).
To fix this, remove the xdp_buff pointer from the rx_buf union and
move it one step higher to the union above which only has pointers to
arrays in it. This solves the problem and we can directly feed the SW
ring of xdp_buff pointers straight into the allocation function in the
next patch when that interface is used. This will improve performance.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-4-magnus.karlsson@gmail.com
Add a new driver interface xsk_buff_alloc_batch() offering batched
buffer allocations to improve performance. The new interface takes
three arguments: the buffer pool to allocated from, a pointer to an
array of struct xdp_buff pointers which will contain pointers to the
allocated xdp_buffs, and an unsigned integer specifying the max number
of buffers to allocate. The return value is the actual number of
buffers that the allocator managed to allocate and it will be in the
range 0 <= N <= max, where max is the third parameter to the function.
u32 xsk_buff_alloc_batch(struct xsk_buff_pool *pool, struct xdp_buff **xdp,
u32 max);
A second driver interface is also introduced that need to be used in
conjunction with xsk_buff_alloc_batch(). It is a helper that sets the
size of struct xdp_buff and is used by the NIC Rx irq routine when
receiving a packet. This helper sets the three struct members data,
data_meta, and data_end. The two first ones is in the xsk_buff_alloc()
case set in the allocation routine and data_end is set when a packet
is received in the receive irq function. This unfortunately leads to
worse performance since the xdp_buff is touched twice with a long time
period in between leading to an extra cache miss. Instead, we fill out
the xdp_buff with all 3 fields at one single point in time in the
driver, when the size of the packet is known. Hence this helper. Note
that the driver has to use this helper (or set all three fields
itself) when using xsk_buff_alloc_batch(). xsk_buff_alloc() works as
before and does not require this.
void xsk_buff_set_size(struct xdp_buff *xdp, u32 size);
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210922075613.12186-3-magnus.karlsson@gmail.com
- Fix 'perf test' DWARF unwind for optimized builds.
- Fix 'perf test' 'Object code reading' when dealing with samples in @plt
symbols.
- Fix off-by-one directory paths in the ARM support code.
- Fix error message to eliminate confusion in 'perf config' when first creating
a config file.
- 'perf iostat' fix for system wide operation.
- Fix printing of metrics when 'perf iostat' is used with one or more
iio_root_ports and unconnected cpus (using -C).
- Fix several typos in the documentation files.
- Fix spelling mistake "icach" -> "icache" in the power8 JSON vendor files.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYVIO3wAKCRCyPKLppCJ+
J9piAP4jmxYEnimD6qvVHjOLio2LvwGI0u7MakZCHWVKQZKHbgEArb8l3+D2+YXw
U7RxDmXoSE+0EjTV8o13sQlerRTU3wM=
=oVI7
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.15-2021-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools fixes from Arnaldo Carvalho de Melo:
- Fix 'perf test' DWARF unwind for optimized builds.
- Fix 'perf test' 'Object code reading' when dealing with samples in
@plt symbols.
- Fix off-by-one directory paths in the ARM support code.
- Fix error message to eliminate confusion in 'perf config' when first
creating a config file.
- 'perf iostat' fix for system wide operation.
- Fix printing of metrics when 'perf iostat' is used with one or more
iio_root_ports and unconnected cpus (using -C).
- Fix several typos in the documentation files.
- Fix spelling mistake "icach" -> "icache" in the power8 JSON vendor
files.
* tag 'perf-tools-fixes-for-v5.15-2021-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf iostat: Fix Segmentation fault from NULL 'struct perf_counts_values *'
perf iostat: Use system-wide mode if the target cpu_list is unspecified
perf config: Refine error message to eliminate confusion
perf doc: Fix typos all over the place
perf arm: Fix off-by-one directory paths.
perf vendor events powerpc: Fix spelling mistake "icach" -> "icache"
perf tests: Fix flaky test 'Object code reading'
perf test: Fix DWARF unwind for optimized builds.
- missing TLB flush
- nested virtualization fixes for SMM (secure boot on nested hypervisor)
and other nested SVM fixes
- syscall fuzzing fixes
- live migration fix for AMD SEV
- mirror VMs now work for SEV-ES too
- fixes for reset
- possible out-of-bounds access in IOAPIC emulation
- fix enlightened VMCS on Windows 2022
ARM:
- Add missing FORCE target when building the EL2 object
- Fix a PMU probe regression on some platforms
Generic:
- KCSAN fixes
selftests:
- random fixes, mostly for clang compilation
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmFN0EwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNqaQf/Vx7ePFTqwWpo+8wKapnc6JN9SLjC
hM4jipxfc1WyQWcfCt8ZuPhCnhF7o8mG/mrqTm+JB+oGqIsydHW19DiUT8ekv09F
dQ+XYSiR4B547wUH5XLQc4xG9imwYlXGEOHqrE7eJvGH3LOqVFX2fLRBnFefZbO8
GKhRJrGXwG3/JSAP6A0c22iVU+pLbfV9gpKwrAj0V7o8nzT2b3Wmh74WBNb47BzE
a4+AwKpWO4rqJGOwdYwy67pdFHh1YmrlZ59cFZc7fzlXE+o0D0bitaJyioZALpOl
4mRGdzoYkNB++ZjDzVFnAClCYQV/oNxCNGFaFF2mh/gzXG1TLmN7B8zGDg==
=7oVh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"A bit late... I got sidetracked by back-from-vacation routines and
conferences. But most of these patches are already a few weeks old and
things look more calm on the mailing list than what this pull request
would suggest.
x86:
- missing TLB flush
- nested virtualization fixes for SMM (secure boot on nested
hypervisor) and other nested SVM fixes
- syscall fuzzing fixes
- live migration fix for AMD SEV
- mirror VMs now work for SEV-ES too
- fixes for reset
- possible out-of-bounds access in IOAPIC emulation
- fix enlightened VMCS on Windows 2022
ARM:
- Add missing FORCE target when building the EL2 object
- Fix a PMU probe regression on some platforms
Generic:
- KCSAN fixes
selftests:
- random fixes, mostly for clang compilation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (43 commits)
selftests: KVM: Explicitly use movq to read xmm registers
selftests: KVM: Call ucall_init when setting up in rseq_test
KVM: Remove tlbs_dirty
KVM: X86: Synchronize the shadow pagetable before link it
KVM: X86: Fix missed remote tlb flush in rmap_write_protect()
KVM: x86: nSVM: don't copy virt_ext from vmcb12
KVM: x86: nSVM: test eax for 4K alignment for GP errata workaround
KVM: x86: selftests: test simultaneous uses of V_IRQ from L1 and L0
KVM: x86: nSVM: restore int_vector in svm_clear_vintr
kvm: x86: Add AMD PMU MSRs to msrs_to_save_all[]
KVM: x86: nVMX: re-evaluate emulation_required on nested VM exit
KVM: x86: nVMX: don't fail nested VM entry on invalid guest state if !from_vmentry
KVM: x86: VMX: synthesize invalid VM exit when emulating invalid guest state
KVM: x86: nSVM: refactor svm_leave_smm and smm_enter_smm
KVM: x86: SVM: call KVM_REQ_GET_NESTED_STATE_PAGES on exit from SMM mode
KVM: x86: reset pdptrs_from_userspace when exiting smm
KVM: x86: nSVM: restore the L1 host state prior to resuming nested guest on SMM exit
KVM: nVMX: Filter out all unsupported controls when eVMCS was activated
KVM: KVM: Use cpumask_available() to check for NULL cpumask when kicking vCPUs
KVM: Clean up benign vcpu->cpu data races when kicking vCPUs
...
Compiling sb_watchdog needs to clearly define SIBYTE_HDR_FEATURES.
In arch/mips/sibyte/Platform like:
cflags-$(CONFIG_SIBYTE_BCM112X) += \
-I$(srctree)/arch/mips/include/asm/mach-sibyte \
-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
Otherwise, SIBYTE_HDR_FEATURES is SIBYTE_HDR_FMASK_ALL.
SIBYTE_HDR_FMASK_ALL is mean:
#define SIBYTE_HDR_FMASK_ALL SIBYTE_HDR_FMASK_1250_ALL | SIBYTE_HDR_FMASK_112x_ALL \
| SIBYTE_HDR_FMASK_1480_ALL)
So, If not limited to CPU_SB1, we will get such an error:
arch/mips/include/asm/sibyte/bcm1480_scd.h:261: error: "M_SPC_CFG_CLEAR" redefined [-Werror]
arch/mips/include/asm/sibyte/bcm1480_scd.h:262: error: "M_SPC_CFG_ENABLE" redefined [-Werror]
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9d682ea6bc ("vboxsf: Fix the check for the old binary
mount-arguments struct") was meant to fix a build error due to sign
mismatch in 'char' and the use of character constants, but it just moved
the error elsewhere, in that on some architectures characters and signed
and on others they are unsigned, and that's just how the C standard
works.
The proper fix is a simple "don't do that then". The code was just
being silly and odd, and it should never have cared about signed vs
unsigned characters in the first place, since what it is testing is not
four "characters", but four bytes.
And the way to compare four bytes is by using "memcmp()".
Which compilers will know to just turn into a single 32-bit compare with
a constant, as long as you don't have crazy debug options enabled.
Link: https://lore.kernel.org/lkml/20210927094123.576521-1-arnd@kernel.org/
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the CQE size of the user space is not the size supported by the
hardware, the creation of CQ should be stopped.
Fixes: 09a5f210f6 ("RDMA/hns: Add support for CQE in size of 64 Bytes")
Link: https://lore.kernel.org/r/20210927125557.15031-3-liangwenpeng@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The size of CQE is different for different versions of hardware, so the
driver needs to specify the size of CQE explicitly.
Fixes: 09a5f210f6 ("RDMA/hns: Add support for CQE in size of 64 Bytes")
Link: https://lore.kernel.org/r/20210927125557.15031-2-liangwenpeng@huawei.com
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Pointers should be printed with %p or %px rather than cast to 'unsigned
long long' and printed with %llx. Change %llx to %p to print the secured
pointer.
Fixes: 042a00f93a ("IB/{ipoib,hfi1}: Add a timeout handler for rdma_netdev")
Link: https://lore.kernel.org/r/20210922134857.619602-1-qtxuning1999@sjtu.edu.cn
Signed-off-by: Guo Zhi <qtxuning1999@sjtu.edu.cn>
Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The e100_get_regs function is used to implement a simple register dump
for the e100 device. The data is broken into a couple of MAC control
registers, and then a series of PHY registers, followed by a memory dump
buffer.
The total length of the register dump is defined as (1 + E100_PHY_REGS)
* sizeof(u32) + sizeof(nic->mem->dump_buf).
The logic for filling in the PHY registers uses a convoluted inverted
count for loop which counts from E100_PHY_REGS (0x1C) down to 0, and
assigns the slots 1 + E100_PHY_REGS - i. The first loop iteration will
fill in [1] and the final loop iteration will fill in [1 + 0x1C]. This
is actually one more than the supposed number of PHY registers.
The memory dump buffer is then filled into the space at
[2 + E100_PHY_REGS] which will cause that memcpy to assign 4 bytes past
the total size.
The end result is that we overrun the total buffer size allocated by the
kernel, which could lead to a panic or other issues due to memory
corruption.
It is difficult to determine the actual total number of registers
here. The only 8255x datasheet I could find indicates there are 28 total
MDI registers. However, we're reading 29 here, and reading them in
reverse!
In addition, the ethtool e100 register dump interface appears to read
the first PHY register to determine if the device is in MDI or MDIx
mode. This doesn't appear to be documented anywhere within the 8255x
datasheet. I can only assume it must be in register 28 (the extra
register we're reading here).
Lets not change any of the intended meaning of what we copy here. Just
extend the space by 4 bytes to account for the extra register and
continue copying the data out in the same order.
Change the E100_PHY_REGS value to be the correct total (29) so that the
total register dump size is calculated properly. Fix the offset for
where we copy the dump buffer so that it doesn't overrun the total size.
Re-write the for loop to use counting up instead of the convoluted
down-counting. Correct the mdio_read offset to use the 0-based register
offsets, but maintain the bizarre reverse ordering so that we have the
ABI expected by applications like ethtool. This requires and additional
subtraction of 1. It seems a bit odd but it makes the flow of assignment
into the register buffer easier to follow.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
commit abf9b90205 ("e100: cleanup unneeded math") tried to simplify
e100_get_regs_len and remove a double 'divide and then multiply'
calculation that the e100_reg_regs_len function did.
This change broke the size calculation entirely as it failed to account
for the fact that the numbered registers are actually 4 bytes wide and
not 1 byte. This resulted in a significant under allocation of the
register buffer used by e100_get_regs.
Fix this by properly multiplying the register count by u32 first before
adding the size of the dump buffer.
Fixes: abf9b90205 ("e100: cleanup unneeded math")
Reported-by: Felicitas Hetzelt <felicitashetzelt@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Florian Fainelli says:
====================
net: bcmgenet: support for flow control
This patch series adds support for flow control to the GENET driver, the
first 2 patches remove superfluous code, the 3rd one does re-organize
code a little bit and the 4th one ads the support for flow control
proper.
====================
This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.
The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit separates out the MAC configuration that occurs on a
PHY state change into a function named bcmgenet_mac_config().
This allows the function to be called directly elsewhere.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine has been fixed to only call the adjust_link
callback when the link state has changed. Therefore the old link
state variables are no longer needed to detect a change in link
state.
This commit effectively reverts
commit 5ad6e6c508 ("net: bcmgenet: improve bcmgenet_mii_setup()")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcmgenet_mii_setup() function is registered as the adjust_link
callback from the phylib for the GENET driver.
The phylib always sets the netif_carrier according to phydev->link
prior to invoking the adjust_link callback, so there is no need to
repeat that in the link down case within the network driver.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij says:
====================
RTL8366(RB) cleanups part 1
This is a first set of patches making the RTL8366RB work out of
the box with a default OpenWrt userspace.
We achieve bridge port isolation with the first patch, and the
next 5 patches removes the very weird VLAN set-up with one
VLAN with PVID per port that has been in this driver in all
vendor trees and in OpenWrt for years.
The switch is now managed the way a modern bridge/DSA switch
shall be managed.
After these patches are merged, I will send the next set which
adds new features, some which have circulated before.
ChangeLog v4->v5:
- Drop the patch disabling 4K VLAN.
- Drop the patch forcing VLAN0 untagged.
- Fix a semantic bug in the filer enablement code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need a message for every VLAN association, dbg
is fine. The message about adding the DSA or CPU
port to a VLAN is directly misleading, this is perfectly
fine.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking that the MC (member config) was != 0
for some reason, all we need to check is that the config
has no ports, i.e. no members. Then it can be recycled.
This must be some misunderstanding.
Fixes: 4ddcaf1ebb ("net: dsa: rtl8366: Properly clear member config")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we were defining one VLAN per port for isolating the ports
the port_vlan_filtering() callback was implemented to enable a
VLAN on the port + 1. This function makes no sense, not only is
it incomplete as it only enables the VLAN, it doesn't do what
the callback is supposed to do, which is to selectively enable
and disable filtering on a certain port.
Implement the correct callback: we have two registers dealing
with filtering on the RTL9366RB, so we implement an ASIC-specific
callback and implement filering using the register bit that makes
the switch drop frames if the port is not in the VLAN member set.
The DSA documentation Documentation/networking/switchdev.rst states:
When the bridge has VLAN filtering enabled and a PVID is not
configured on the ingress port, untagged and 802.1p tagged
packets must be dropped. When the bridge has VLAN filtering
enabled and a PVID exists on the ingress port, untagged and
priority-tagged packets must be accepted and forwarded according
to the bridge's port membership of the PVID VLAN. When the
bridge has VLAN filtering disabled, the presence/lack of a
PVID should not influence the packet forwarding decision.
To comply with this, we add two arrays of bool in the RTL8366RB
state that keeps track of if filtering and PVID is enabled or
not for each port. We then add code such that whenever filtering
or PVID changes, we update the filter according to the
specification.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hacky default VLAN setup was done in order to direct
packets to the right ports and provide port isolation, both
which we now support properly using custom tags and proper
bridge port isolation.
We can drop the custom VLAN code and leave all VLAN handling
alone, as users expect things to be. We can also drop
ds->configure_vlan_while_not_filtering = false; and let
the core deal with any VLANs it wants.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use port isolation registers to configure bridge offloading.
Tested on the D-Link DIR-685, switching between ports and
sniffing ports to make sure no packets leak.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Move devlink_register to be last devlink command
This is second version of patch series
https://lore.kernel.org/netdev/cover.1628599239.git.leonro@nvidia.com/
The main change is addition of delayed notification logic that will
allowed us to delete devlink_params_publish API (future series will
remove it completely) and conversion of all drivers to have devlink_register
being last commend.
The series itself is pretty straightforward, except liquidio driver
which performs initializations in various workqueues without proper
locks. That driver doesn't hole device_lock and it is clearly broken
for any parallel driver core flows (modprobe + devlink + PCI reset will
100% crash it).
In order to annotate devlink_register() will lockdep of holding
device_lock, I added workaround in this driver.
Thanks
----------------------
From previous cover letter:
Hi Dave and Jakub,
This series prepares code to remove devlink_reload_enable/_disable API
and in order to do, we move all devlink_register() calls to be right
before devlink_reload_enable().
The best place for such a call should be right before exiting from
the probe().
This is done because devlink_register() opens devlink netlink to the
users and gives them a venue to issue commands before initialization
is finished.
1. Some drivers were aware of such "functionality" and tried to protect
themselves with extra locks, state machines and devlink_reload_enable().
Let's assume that it worked for them, but I'm personally skeptical about
it.
2. Some drivers copied that pattern, but without locks and state
machines. That protected them from reload flows, but not from any _set_
routines.
3. And all other drivers simply didn't understand the implications of early
devlink_register() and can be seen as "broken".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink
is fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured. Indirectly this change fixes the commit mentioned
below where devlink_unregister() was prematurely removed.
Fixes: db4278c55f ("devlink: Make devlink_register to be void")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open user space access to the devlink after driver is probed.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open access to the devlink interface when the driver fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that devlink is open to receive user input when all
parameters are initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to make sure that devlink_register() is the last
command during initialization stage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate devlink registrations and traps registrations so devlink will
be registered when driver is fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change prevents from users to access device before devlink is fully
configured. This change allows us to delete call to devlink_params_publish()
and impossible check during unregister flow.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move devlink_registration routine to be the last command, when the
device is fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
