This driver assumed that dmaengine_tx_status() could return
the residue even if the transfer was completed. However,
this was not correct usage [1] and this caused to break getting
the residue after the commit 24461d9792 ("dmaengine:
virt-dma: Fix access after free in vchan_complete()") actually.
So, this is possible to get wrong received size if the usb
controller gets a short packet. For example, g_zero driver
causes "bad OUT byte" errors.
The usb-dmac driver will support the callback_result, so this
driver can use it to get residue correctly. Note that even if
the usb-dmac driver has not supported the callback_result yet,
this patch doesn't cause any side-effects.
[1]
https://lore.kernel.org/dmaengine/20200616165550.GP2324254@vkoul-mobl/
Reported-by: Hien Dang <hien.dang.eb@renesas.com>
Fixes: 24461d9792 ("dmaengine: virt-dma: Fix access after free in vchan_complete()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1592482277-19563-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200419125705.GA5172@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
In order to enforce suspend/resume ordering, this commit creates link
between phy consumers and phy devices. This link avoids to suspend phy
before phy consumers.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[jonathanh@nvidia.com: Fix an abort when of_phy_get() returns error]
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Renesas USBHS driver includes a bit of surplus headers
and uses the old GPIO API so let's switch it to use the
GPIO descriptor.
I noticed that the enable_gpio inside renesas_usbhs_driver_param
isn't really referenced anywhere, and it is also the wrong
type (u32) so let's just delete it and use a local variable
instead.
Cc: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191217141241.57639-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the type of buf in __usbhsg_recip_send_status to
be __le16 to avoid the following sparse warning:
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: expected unsigned short
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: got restricted __le16 [usertype]
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following sparse warnings by shifting 8-bits after
le16_to_cpu().
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: restricted __le16 degrades to integer
drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: cast to restricted __le16
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the warnings generated by casting to/from __le16 without
using the correct functions.
Fixes the following sparse warnings:
drivers/usb/renesas_usbhs/common.c:165:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:165:25: expected restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:165:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:166:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:166:25: expected restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:166:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:167:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:167:25: expected restricted __le16 [usertype] wLength
drivers/usb/renesas_usbhs/common.c:167:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:173:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:173:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:173:39: got restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:174:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:174:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:174:39: got restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:175:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:175:39: expected unsigned short [usertype] data
Note. I belive this to be correct, and should be a no-op on arm.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the type of buf in __usbhsg_recip_send_status to
be __le16 to avoid the following sparse warning:
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: expected unsigned short
drivers/usb/renesas_usbhs/mod_gadget.c:335:14: got restricted __le16 [usertype]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191015153017.10858-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the warnings generated by casting to/from __le16 without
using the correct functions.
Fixes the following sparse warnings:
drivers/usb/renesas_usbhs/common.c:165:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:165:25: expected restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:165:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:166:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:166:25: expected restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:166:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:167:25: warning: incorrect type in assignment (different base types)
drivers/usb/renesas_usbhs/common.c:167:25: expected restricted __le16 [usertype] wLength
drivers/usb/renesas_usbhs/common.c:167:25: got unsigned short
drivers/usb/renesas_usbhs/common.c:173:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:173:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:173:39: got restricted __le16 [usertype] wValue
drivers/usb/renesas_usbhs/common.c:174:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:174:39: expected unsigned short [usertype] data
drivers/usb/renesas_usbhs/common.c:174:39: got restricted __le16 [usertype] wIndex
drivers/usb/renesas_usbhs/common.c:175:39: warning: incorrect type in argument 3 (different base types)
drivers/usb/renesas_usbhs/common.c:175:39: expected unsigned short [usertype] data
Note. I belive this to be correct, and should be a no-op on arm.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191015155044.11858-1-ben.dooks@codethink.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to usb_ep_set_halt()'s description,
__usbhsg_ep_set_halt_wedge() should return -EAGAIN if the IN endpoint
has any queue or data. Otherwise, this driver is possible to cause
just STALL without sending a short packet data on g_mass_storage driver,
and then a few resetting a device happens on a host side during
a usb enumaration.
Fixes: 2f98382dcd ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
had added a usbhsg_pipe_disable() calling into
__usbhsg_ep_set_halt_wedge() accidentally. But, this driver should
not call the usbhsg_pipe_disable() because the function discards
all queues. So, this patch removes it.
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1569924633-322-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When R-Car Gen3 USB 2.0 is in Gadget mode, if host is detached an interrupt
will be generated and Suspended state bit is set in interrupt status
register. Interrupt handler will call driver->suspend(composite_suspend)
if suspended state bit is set. composite_suspend will call
ffs_func_suspend which will post FUNCTIONFS_SUSPEND and will be consumed
by user space application via /dev/ep0.
To be able to detect host detach, extend the DVSQ_MASK to cover the
Suspended bit of the DVSQ[2:0] bitfield from the Interrupt Status
Register 0 (INTSTS0) register and perform appropriate action in the
DVST interrupt handler (usbhsg_irq_dev_state).
Without this commit, disconnection of the phone from R-Car-H3 ES2.0
Salvator-X CN9 port is not recognized and reverse role switch does
not happen. If phone is connected again it does not enumerate.
With this commit, disconnection will be recognized and reverse role
switch will happen by a user space application. If phone is connected
again it will enumerate properly and will become visible in the output
of 'lsusb'.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-3-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit [1] enabled the possibility of checking the DVST (Device State
Transition) bit of INTSTS0 (Interrupt Status Register 0) and calling
the irq_dev_state() handler if the DVST bit is set. But neither
commit [1] nor commit [2] actually enabled the DVSE (Device State
Transition Interrupt Enable) bit in the INTENB0 (Interrupt Enable
Register 0). As a consequence, irq_dev_state() handler is getting
called as a side effect of other (non-DVSE) interrupts being fired,
which definitely can't be relied upon, if DVST notifications are of
any value.
Why this doesn't hurt is because usbhsg_irq_dev_state() currently
doesn't do much except of a dev_dbg(). Once more work is added to
the handler (e.g. detecting device "Suspended" state and notifying
other USB gadget components about it), enabling DVSE becomes a hard
requirement. Do it in a standalone commit for better visibility and
clear explanation.
[1] commit f1407d5c66 ("usb: renesas_usbhs: Add Renesas USBHS common
code")
[2] commit 2f98382dcd ("usb: renesas_usbhs: Add Renesas USBHS Gadget")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-2-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to usbhs_status_get_ctrl_stage(), *_get_device_state() is not
supposed to return any error code since its return value is the DVSQ
bitfield of the INTSTS0 register. According to SoC HW manual rev1.00,
every single value of DVSQ[2:0] is valid and none is an error:
----8<----
Device State
000: Powered state
001: Default state
010: Address state
011: Configuration state
1xx: Suspended state
----8<----
Hence, simplify the function body. The motivation behind dropping the
switch/case construct is being able to implement reading the suspended
state. The latter (based on the above DVSQ[2:0] description) doesn't
have a unique value, but is rather a list of states (which makes
switch/case less suitable for reading/validating it):
100: (Suspended) Powered state
101: (Suspended) Default state
110: (Suspended) Address state
111: (Suspended) Configuration state
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-1-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904085045.24204-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=ciUl
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: more changes for v5.3 merge window
Turns out a few more important changes came about. We have the new
Cadence DRD Driver being added here and that's the biggest, most
important part.
Together with that we have suport for new imx7ulp phy. Support for
TigerLake Devices on dwc3. Also a couple important fixes which weren't
completed in time for the -rc cycle.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
* tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: renesas_usbhs: add a workaround for a race condition of workqueue
usb: gadget: udc: renesas_usb3: remove redundant assignment to ret
usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset()
USB: gadget: function: fix issue Unneeded variable: "value"
usb: phy: phy-mxs-usb: add imx7ulp support
doc: dt-binding: mxs-usb-phy: add compatible for 7ulp
usb:cdns3 Fix for stuck packets in on-chip OUT buffer.
usb:cdns3 Add Cadence USB3 DRD Driver
usb:gadget Simplify usb_decode_get_set_descriptor function.
usb:gadget Patch simplify usb_decode_set_clear_feature function.
usb:gadget Separated decoding functions from dwc3 driver.
dt-bindings: add binding for USBSS-DRD controller.
usb: dwc3: pci: add support for TigerLake Devices
The old commit 6e4b74e469 ("usb: renesas: fix scheduling in atomic
context bug") fixed an atomic issue by using workqueue for the shdmac
dmaengine driver. However, this has a potential race condition issue
between the work pending and usbhsg_ep_free_request() in gadget mode.
When usbhsg_ep_free_request() is called while pending the queue,
since the work_struct will be freed and then the work handler is
called, kernel panic happens on process_one_work().
To fix the issue, if we could call cancel_work_sync() at somewhere
before the free request, it could be easy. However,
the usbhsg_ep_free_request() is called on atomic (e.g. f_ncm driver
calls free request via gether_disconnect()).
For now, almost all users are having "USB-DMAC" and the DMAengine
driver can be used on atomic. So, this patch adds a workaround for
a race condition to call the DMAengine APIs without the workqueue.
This means we still have TODO on shdmac environment (SH7724), but
since it doesn't have SMP, the race condition might not happen.
Fixes: ab330cf388 ("usb: renesas_usbhs: add support for USB-DMAC")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now the driver fixes the issue of the commit 482982062f ("usb:
gadget: renesas_usbhs: bugfix: don't modify platform data") by
using usbhs_mod_info.get_vbus, this patches uses the pointer
instead of copied value to avoid redundancy. Note that struct
renesas_usbhs_driver_param has to use copied value because
the driver has to set some members (e.g. buswait_bwait).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In device tree environment, the previous code allocates
renesas_usbhs_platform_info by using devm_kzalloc() and then copies
usbhs_of_data to the allocated memory. This reason is some values
(e.g. .platform_callback.get_vbus) are overwritten by the driver,
but the of_device_id.data is "const". Now the driver doesn't have
such a code, so this patch uses renesas_usbhs_platform_info on
of_device_id.data.
Note that the previous code set the pdev->dev.platform_data pointer
even if device tree environment, but the value is not used. So,
this patch also remove such a code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All platform related codes (rcar[23].c and rza{2}.c) has its own
.get_id function as "USBHS_GADGET". So, we can use a common
function for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c) to remove
usbhs_parse_dt(). So, this patch moves device tree properties
parsing to usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this can remove over 80 charactors in a line, this patch adds
struct device * declaration in usbhs_probe().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, each struct renesas_usbhs_driver_param is stored on
the each platform related source code (e.g. rcar3.c). So, to simplify
the source code, this patch adds a new flag has_new_pipe_configs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the dev_of_node macro instead of open coded
to be better.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now no one uses the type member so that this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To remove the type of renesas_usbhs_driver_param in the future, this
patch uses a specific flag "multi_clks".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The very old commit 482982062f ("usb: gadget: renesas_usbhs:
bugfix: don't modify platform data") changed to use copied whole
structures values to fix the "hung-up" issue. However, we also
can fix the issue if the driver copies the get_vbus function
pointer to the driver's value.
So, this patch adds get_vbus member into struct usbhs_mod_info and
use the pointer instead of struct renesas_usbhs_platform_callback.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future, since other source code of this driver will use these
macros, this patch moves it to the header file.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notify_hotplug callback was supported in v3.10, but the last user
(armadillo800eva) was removed by the commit 1fa59bda21 ("ARM: shmobile:
Remove legacy board code for Armadillo-800 EVA"). So, this patch
removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the irq_vbus comments doesn't match with the current
implementation, this patch revises it. This patch also changes
new lines to reduce the source code lines.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid the error-proneness of calls to sizeof() in the memcpy,
this patch uses struct assignment instead of memcpy.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>---
This patch is based on Greg's linux-usb.git / usb-next branch.
Note that mod_host.c also has memcpy but we cannot use struct assignment
for it because the type of urb->setup_patcket is just "unsigned char *".
drivers/usb/renesas_usbhs/common.c | 13 ++++---------
1 file changed, 4 insertions(+), 9 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Controlling PWMEN/EXTLP (named as "has_otg") was supported in v3.2,
but the last user (kzm9g) was removed by the commit 30f8925a57
("ARM: shmobile: Remove legacy board code for KZM-A9-GT"). So, this
patch remove it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SUDMAC feature was supported in v3.10, but was never used by
any platform. So, this patch removes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RZ/A2 is similar to the R-Car Gen3 with some small differences.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC have a CFIFO register that is byte addressable. This means
when the CFIFO access is set to 32-bit, you can write 8-bit values to
addresses CFIFO+0, CFIFO+1, CFIFO+2, CFIFO+3.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some SoC, CNEN must be set for USB Device mode operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move options from 'flags' field in private structure to param structure
where other options are already being kept.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a specific struct "usbhs_of_data" to add a new SoC
data easily instead of code basis in the future.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/timers/timers-howto.txt, a driver should
use usleep_range() instead of udelay() on NON-ATOMIC CONTEXT if
"SLEEPING FOR ~USECS OR SMALL MSECS ( 10us - 20ms)".
Since the .hardware_init() and .power_ctrl() will run on NON-ATOMIC
CONTEXT, this patch replaces udelay() with usleep_range().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HS-USB found in RZ/G2E (a.k.a. r8a774c0) is very similar to the
one found in R-Car E3 (a.k.a. r8a77990), as it needs to release
the PLL reset by the UGCTRL register like R-Car E3, therefore add
r8a774c0 support in a similar fashion to what was done for the
r8a77990.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without CONFIG_PM, we get a new build warning here:
drivers/usb/renesas_usbhs/common.c:860:12: error: 'usbhsc_resume' defined but not used [-Werror=unused-function]
static int usbhsc_resume(struct device *dev)
^~~~~~~~~~~~~
drivers/usb/renesas_usbhs/common.c:844:12: error: 'usbhsc_suspend' defined but not used [-Werror=unused-function]
static int usbhsc_suspend(struct device *dev)
^~~~~~~~~~~~~~
Fixes: d54d334e75 ("usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
