Extend MAC support to support also lag interfaces:
1. In case an entry is learned on a port that is part of lag interface,
then notify the upper layers that the entry is learned on the bond
interface
2. If a port leaves the bond and the port is the first port in the lag
group, then it is required to update all MAC entries to change the
destination port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link aggregation hardware offload support for lan966x
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose lan966x_switchdev_nb and lan966x_switchdev_blocking_nb to the
lan966x_main.h file because they will be needed by the lag driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a port leaves a bridge, flush the workqueue of the FDB work.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself. The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.
It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.
Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the PTP programmable pins to implement also PTP_PF_EXTTS
function. The PTP pin can be configured to capture only on the rising
edge of the PPS signal. And once an event is seen then an interrupt is
generated and the local time counter is saved.
The interrupt is shared between all the pins.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lan966x has 8 PTP programmable pins, where the last pins is hardcoded to
be used by PHC0, which does the frame timestamping. All the rest of the
PTP pins can be shared between the PHCs and can have different functions
like perout or extts. For now add support for PTP_FS_PEROUT.
The HW is not able to support absolute start time but can use the nsec
for phase adjustment when generating PPS.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MTU, it is required to change also the size of the
DBs. In case those frames will arrive to CPU.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ethernet frames can be extracted or injected to or from the device's
DDR memory. There is one channel for injection and one channel for
extraction. Each of these channels contain a linked list of DCBs which
contains DB. The DCB contains only 1 DB for both the injection and
extraction. Each DB contains a frame. Every time when a frame is received
or transmitted an interrupt is generated.
It is not possible to use both the FDMA and the manual
injection/extraction of the frames. Therefore the FDMA has priority over
the manual because of better performance values.
FDMA:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 420 MBytes 352 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 420 MBytes 351 Mbits/sec receiver
iperf -c 192.168.1.1 -R
[ 5] 0.00-10.01 sec 528 MBytes 442 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 524 MBytes 440 Mbits/sec receiver
Manual:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 93.8 MBytes 78.5 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 93.8 MBytes 78.4 Mbits/sec receiver
ipers -c 192.168.1.1 -R
[ 5] 0.00-10.03 sec 121 MBytes 101 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 118 MBytes 99.0 Mbits/sec receiver
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Expose the following functions 'lan966x_hw_offload',
'lan966x_ifh_get_src_port' and 'lan966x_ifh_get_timestamp' in
lan966x_main.h so they can be accessed by FDMA.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The registers used to inject a frame to one of the ports is shared
between all the net devices. Therefore, there can be race conditions for
accessing the registers when two processes send frames at the same time
on different ports.
To fix this, add a spinlock around the function
'lan966x_port_ifh_xmit()'.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the multicast snooping is disabled, the mdb entries should be
removed from the HW, but they still need to be kept in memory for when
the mcast_snooping will be enabled again.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback allows to enable/disable multicast snooping.
When the snooping is enabled, all IGMP and MLD frames are redirected to
the CPU, therefore make sure not to set the skb flag 'offload_fwd_mark'.
The HW will not flood multicast ipv4/ipv6 data frames.
When the snooping is disabled, the HW will flood IGMP, MLD and multicast
ipv4/ipv6 frames according to the mcast_flood flag.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing 2-step timestamping the HW will generate an interrupt when it
managed to timestamp a frame. It is the SW responsibility to read it
from the FIFO.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update both the extraction and injection to do timestamping of the
frames. The extraction is always doing the timestamping while for
injection is doing the timestamping only if it is configured.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ioctl callbacks SIOCSHWTSTAMP and SIOCGHWTSTAMP to allow
to configure the ports to enable/disable timestamping for TX. The RX
timestamping is always enabled. The HW is capable to run both 1-step
timestamping and 2-step timestamping.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan966x has 3 PHC. Enable each of them, for now all the
timestamping is happening on the first PHC.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend lan966x driver with mdb support by implementing the switchdev
calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB.
It is allowed to add both ipv4/ipv6 entries and l2 entries. To add
ipv4/ipv6 entries is not required to use the PGID table while for l2
entries it is required. The PGID table is much smaller than MAC table
so only fewer l2 entries can be added.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first entries in the PGID table are used by the front ports while
the last entries are used for different purposes like flooding mask,
copy to CPU, etc. So add these macros to define which entries can be
used for general purpose.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend mac functionality with the function lan966x_mac_ip_learn. This
function adds an entry in the MAC table for IP multicast addresses.
These entries can copy a frame to the CPU but also can forward on the
front ports.
This functionality is needed for mdb support. In case the CPU and some
of the front ports subscribe to an IP multicast address.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series extends the current supported bridge flags with the
following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend lan966x driver with fdb support by implementing the switchdev
calls SWITCHDEV_FDB_ADD_TO_DEVICE and SWITCHDEV_FDB_DEL_TO_DEVICE.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the driver to support vlan filtering by implementing the
switchdev calls SWITCHDEV_OBJ_ID_PORT_VLAN,
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support to offload in the HW the forwarding of the
frames. The driver registers to the switchdev callbacks and implements
the callbacks for attributes SWITCHDEV_ATTR_ID_PORT_STP_STATE and
SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME.
It is not allowed to add a lan966x port to a bridge that contains a
different interface than lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for adding/removing mac entries in the SW list
of entries and in the HW table. This is used by the bridge
functionality.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for handling the interrupts generated by the
analyzer. Currently, only the MAC table generates these interrupts.
The MAC table will generate an interrupt whenever it learns or forgets
an entry in the table. It is the SW responsibility figure out which
entries were added/removed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for statistics counters for the network
interfaces. Also adds support for configuring the network interface via
ethtool like: speed, duplex etc.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for MAC table operations like add and forget.
Also add the functionality to read the MAC address from DT, if there is
no MAC set in DT it would use a random one.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for netdev and phylink in the switch. The
injection + extraction is register based. This will be replaced with DMA
accees.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic SwitchDev driver framework for lan966x. It
includes only the IO range mapping and probing of the switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>