Patch series "New page table range API", v6.
This patchset changes the API used by the MM to set up page table entries.
The four APIs are:
set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)
flush_dcache_folio() isn't technically new, but no architecture
implemented it, so I've done that for them. The old APIs remain around
but are mostly implemented by calling the new interfaces.
The new APIs are based around setting up N page table entries at once.
The N entries belong to the same PMD, the same folio and the same VMA, so
ptep++ is a legitimate operation, and locking is taken care of for you.
Some architectures can do a better job of it than just a loop, but I have
hesitated to make too deep a change to architectures I don't understand
well.
One thing I have changed in every architecture is that PG_arch_1 is now a
per-folio bit instead of a per-page bit when used for dcache clean/dirty
tracking. This was something that would have to happen eventually, and it
makes sense to do it now rather than iterate over every page involved in a
cache flush and figure out if it needs to happen.
The point of all this is better performance, and Fengwei Yin has measured
improvement on x86. I suspect you'll see improvement on your architecture
too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/20230206140639.538867-5-fengwei.yin@intel.com/
You'll need to run it on an XFS filesystem and have
CONFIG_TRANSPARENT_HUGEPAGE set.
This patchset is the basis for much of the anonymous large folio work
being done by Ryan, so it's received quite a lot of testing over the last
few months.
This patch (of 38):
Determine if a value lies within a range more efficiently (subtraction +
comparison vs two comparisons and an AND). It also has useful (under some
circumstances) behaviour if the range exceeds the maximum value of the
type. Convert all the conflicting definitions of in_range() within the
kernel; some can use the generic definition while others need their own
definition.
Link: https://lkml.kernel.org/r/20230802151406.3735276-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230802151406.3735276-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The msm_gem_get_vaddr() returns an ERR_PTR() on failure, and a null
is catastrophic here, so we should use IS_ERR_OR_NULL() to check
the return value.
Fixes: 6a8bd08d04 ("drm/msm: add sudo flag to submit ioctl")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/547712/
Signed-off-by: Rob Clark <robdclark@chromium.org>
These fields are deprecated. But any userspace new enough to support
a690 also knows how to identify the GPU based on chip-id.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/545552/
Recently, a WARN_ON() was introduced to ensure that revn is filled before
adreno_is_aXYZ is called. This however doesn't work very well when revn is
0 by design (such as for A635).
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: cc943f43ec ("drm/msm/adreno: warn if chip revn is verified before being set")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Patchwork: https://patchwork.freedesktop.org/patch/545554/
A610 is implemented on at least three SoCs: SM6115 (bengal), SM6125
(trinket) and SM6225 (khaje). Trinket does not support speed binning
(only a single SKU exists) and we don't yet support khaje upstream.
Hence, add a fuse mapping table for bengal to allow for per-chip
frequency limiting.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542780/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A619_holi is implemented on at least two SoCs: SM4350 (holi) and SM6375
(blair). This is what seems to be a first occurrence of this happening,
but it's easy to overcome by guarding the SoC-specific fuse values with
of_machine_is_compatible(). Do just that to enable frequency limiting
on these SoCs.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542772/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before transitioning to using per-SoC and not per-Adreno speedbin
fuse values (need another patchset to land elsewhere), a good
improvement/stopgap solution is to use adreno_is_aXYZ macros in
place of explicit revision matching. Do so to allow differentiating
between A619 and A619_holi.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542777/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GPU can only be one at a time. Turn a series of ifs into if +
elseifs to save some CPU cycles.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542770/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Adreno 619 expects some tunables to be set differently. Make up for it.
Fixes: b7616b5c69 ("drm/msm/adreno: Add A619 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542782/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A610 is one of (if not the) lowest-tier SKUs in the A6XX family. It
features no GMU, as it's implemented solely on SoCs with SMD_RPM.
What's more interesting is that it does not feature a VDDGX line
either, being powered solely by VDDCX and has an unfortunate hardware
quirk that makes its reset line broken - after a couple of assert/
deassert cycles, it will hang for good and will not wake up again.
This GPU requires mesa changes for proper rendering, and lots of them
at that. The command streams are quite far away from any other A6XX
GPU and hence it needs special care. This patch was validated both
by running an (incomplete) downstream mesa with some hacks (frames
rendered correctly, though some instructions made the GPU hangcheck
which is expected - garbage in, garbage out) and by replaying RD
traces captured with the downstream KGSL driver - no crashes there,
ever.
Add support for this GPU on the kernel side, which comes down to
pretty simply adding A612 HWCG tables, altering a few values and
adding a special case for handling the reset line.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542779/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A619_holi is a GMU-less variant of the already-supported A619 GPU.
It's present on at least SM4350 (holi) and SM6375 (blair). No mesa
changes are required. Add the required kernel-side support for it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542775/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A610 and A619_holi don't support the feature. Disable it to make the GPU stop
crashing after almost each and every submission - the received data on
the GPU end was simply incomplete in garbled, resulting in almost nothing
being executed properly. Extend the disablement to adreno_has_gmu_wrapper,
as none of the GMU wrapper Adrenos that don't support yet seem to feature it.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542774/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some (particularly SMD_RPM, a.k.a non-RPMh) SoCs implement A6XX GPUs
but don't implement the associated GMUs. This is due to the fact that
the GMU directly pokes at RPMh. Sadly, this means we have to take care
of enabling & scaling power rails, clocks and bandwidth ourselves.
Reuse existing Adreno-common code and modify the deeply-GMU-infused
A6XX code to facilitate these GPUs. This involves if-ing out lots
of GMU callbacks and introducing a new type of GMU - GMU wrapper (it's
the actual name that Qualcomm uses in their downstream kernels).
This is essentially a register region which is convenient to model
as a device. We'll use it for managing the GDSCs. The register
layout matches the actual GMU_CX/GX regions on the "real GMU" devices
and lets us reuse quite a bit of gmu_read/write/rmw calls.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542766/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since the introduction of A6xx support, we've been enabling the CX GMU
power counter 0 in a bit of a weird spot. Move it to hw_init so that
GMU wrapper GPUs can reuse the same code paths. As a bonus, this order
makes it easier to compare mainline and downstream register access traces.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542765/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Rename lower_bit to hbb_lo and explain what it signifies.
Add explanations (wherever possible to other tunables).
Port setting min_access_length, ubwc_mode and hbb_hi from downstream.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542764/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently we're only deasserting REG_A6XX_RBBM_GBIF_HALT, but we also
need REG_A6XX_GBIF_HALT to be set to 0.
This is typically done automatically on successful GX collapse, but in
case that fails, we should take care of it.
Also, add a memory barrier to ensure it's gone through before jumping
to further initialization.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542760/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce a6xx_gpu_sw_reset() in preparation for adding GMU wrapper
GPUs and reuse it in a6xx_gmu_force_off().
This helper, contrary to the original usage in GMU code paths, adds
a readback+delay sequence to ensure that the reset is never deasserted
too quickly due to e.g. OoO execution going crazy.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542758/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unify the indentation and explain the cryptic 0xF value.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542756/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This function is responsible for telling the GPU to halt transactions
on all of its relevant buses, drain them and leave them in a predictable
state, so that the GPU can be e.g. reset cleanly.
Move the function to a6xx_gpu.c, remove the static keyword and add a
prototype in a6xx_gpu.h to accomodate for the move.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542762/
Signed-off-by: Rob Clark <robdclark@chromium.org>
As pointed out by Akhil during the review process of GMU wrapper
introduction [1], it makes sense to move this write into the function
that's responsible for forcibly shutting the GMU off.
It is also very convenient to move this to GMU-specific code, so that
it does not have to be guarded by an if-condition to avoid calling it
on GMU wrapper targets.
Move the write to the aforementioned a6xx_gmu_force_off() to achieve
that. No effective functional change.
[1] https://lore.kernel.org/linux-arm-msm/20230501194022.GA18382@akhilpo-linux.qualcomm.com/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542752/
Signed-off-by: Rob Clark <robdclark@chromium.org>
These two will be reused by at least A619_holi in the non-gmu
paths. Turn them non-static them to make it possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542751/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The adreno_is_revn rework came at the same time as A690 introduction
and that resulted in it not covering all cases. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542754/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Change adreno_is_a690() prototype to accept the const struct adreno_gpu
pointer instead of a non-const one. This fixes the following warning:
In file included from drivers/gpu/drm/msm/msm_drv.c:33:
drivers/gpu/drm/msm/adreno/adreno_gpu.h: In function ‘adreno_is_a660_family’:
drivers/gpu/drm/msm/adreno/adreno_gpu.h:303:54: warning: passing argument 1 of ‘adreno_is_a690’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
303 | return adreno_is_a660(gpu) || adreno_is_a690(gpu) || adreno_is_7c3(gpu);
Fixes: 1b90e8f887 ("drm/msm/adreno: change adreno_is_* functions to accept const argument")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/542138/
Link: https://lore.kernel.org/r/20230612182527.3345786-1-dmitry.baryshkov@linaro.org
All adreno_is_*() functions do not modify their argument in any way, so
they can be changed to accept const struct adreno_gpu pointer.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531706/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno
510") tried to check GPU's revn before revn being set. Add WARN_ON_ONCE
to prevent such bugs from happening again. A separate helper is
necessary so that the warning is displayed really just once instead of
being displayed for each of comparisons.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531705/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno
510") added special handling for a510 (this SKU doesn't seem to support
preemption, so the driver should clamp nr_rings to 1). However the
gpu->revn is not yet set (it is set later, in adreno_gpu_init()) and
thus the condition is always false. Check config->rev instead.
Fixes: 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno 510")
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Adam Skladowski <a39.skl@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/531511/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Allow access to CP_PERFCTR_CP_SEL[n] and RB_PERFCTR_RB_SEL which are
used by fdperf and pps-provider (perfetto).
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce support for the Adreno A690, found in Qualcomm SC8280XP.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/540335/
Signed-off-by: Rob Clark <robdclark@chromium.org>
If the Adreno SMMU is dma-coherent, allocation will fail unless we
disable IO_PGTABLE_QUIRK_ARM_OUTER_WBWA. Skip setting this quirk for the
coherent SMMUs (like we have on sm8350 platform).
Fixes: 54af0ceb75 ("arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes")
Reported-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM8450 HDK
Patchwork: https://patchwork.freedesktop.org/patch/531562/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Sparse reports plenty of warnings against the a6xx code because of
a6xx_gmu::mmio and a6xx_gmu::rscc members. For some reason they were
defined as __iomem pointers rather than pointers to __iomem memory.
Correct the __iomem attribute.
Fixes: 02ef80c54e ("drm/msm/a6xx: update pdc/rscc GMU registers for A640/A650")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304070550.NrbhJCvP-lkp@intel.com/
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/531583/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Core:
- Add Marijn Suijten as drm/msm reviewer
- Adreno A660 bindings
- SM8350 MDSS bindings fix
DP:
- Removed obsolete USB-PD remains
- Documented DP compatible string for sm8550 platform
DPU:
- Added support for DPU on sm6350 and sm6375 platforms
- Implemented tearcheck support to support vsync on SM150 and newer platforms
- Enabled missing features (DSPP, DSC, split display) on sc8180x, sc8280xp, sm8450
- Enabled writeback on sc7280
- Enabled DSC on msm8998
- Native HDMI output support
- Dropped unused features: regdma, GC, IGC
- Fixed the DSC flush operations
- Simplified QoS handling, removing obsolete and unused features and merging
SSPP and WB code paths
- Reworked dpu_encoder initialisation path
DSI:
- Added support for DSI and 28nm DSI PHY on MSM8226 platform
- Added support for DSI on sm6350 and sm6375 platforms
- Dropped powerup quirks in favour of using pre_enable_prev_first for
downstream bridges
- Fixed 14nm DSI PHY programming
MDP5:
- Added support for display controller on MSM8226 platform
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The adreno_load_gpu() path is guarded by an error check on
adreno_load_fw(). This function is responsible for loading
Qualcomm-only-signed binaries (e.g. SQE and GMU FW for A6XX), but it
does not take the vendor-signed ZAP blob into account.
By embedding the SQE (and GMU, if necessary) firmware into the
initrd/kernel, we can trigger and unfortunate path that would not bail
out early and proceed with gpu->hw_init(). That will fail, as the ZAP
loader path will not find the firmware and return back to
adreno_load_gpu().
This error path involves pm_runtime_put_sync() which then calls idle()
instead of suspend(). This is suboptimal, as it means that we're not
going through the clean shutdown sequence. With at least A619_holi, this
makes the GPU not wake up until it goes through at least one more
start-fail-stop cycle. The pm_runtime_put_sync that appears in the error
path actually does not guarantee that because of the earlier enabling of
runtime autosuspend.
Fix that by using pm_runtime_put_sync_suspend to force a clean shutdown.
Test cases:
1. All firmware baked into kernel
2. error loading ZAP fw in initrd -> load from rootfs at DE start
Both succeed on A619_holi (SM6375) and A630 (SDM845).
Fixes: 0d997f95b7 ("drm/msm/adreno: fix runtime PM imbalance at gpu load")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/530001/
Link: https://lore.kernel.org/r/20230330231517.2747024-1-konrad.dybcio@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Recently I contributed the switch to OPP API for all Adreno generations.
I did however also skip over the fact that GPUs with a GMU don't specify
a core clock of any kind in the GPU node. While that didn't break
anything, it did introduce unwanted spam in the dmesg:
adreno 5000000.gpu: error -ENOENT: _opp_set_clknames: Couldn't find clock with name: core_clk
Guard the entire logic so that it's not used with GMU-equipped GPUs.
Fixes: 9f251f9340 ("drm/msm/adreno: Use OPP for every GPU generation")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/530347/
Link: https://lore.kernel.org/r/20230223-topic-gmuwrapper-v6-1-2034115bb60c@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit e25e92e08e ("drm/msm: devcoredump iommu fault support")
enabled SMMU stalling to collect GPU state, but only for a6xx. It tied
enabling the stall with tha per-instance pagetables creation.
Since that commit SoCs with a5xx also gained support for
adreno-smmu-priv. Move stalling into generic code and add corresponding
resume_translation calls.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522720/
Link: https://lore.kernel.org/r/20230214123504.3729522-2-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The next generated header update will drop the _LO/_HI suffix, now that
the userspace tooling properly understands 64b vs 32b regs (and the _LO/
_HI workarounds are getting cleaned up). So convert to using the 64b
reg helpers in prep.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527923/
Link: https://lore.kernel.org/r/20230320185416.938842-1-robdclark@gmail.com
Downstream driver appears to not support preemption on A510 target,
trying to use one make device slow and fill log with rings related errors.
Set num_rings to 1 to disable preemption.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: e20c9284c8 ("drm/msm/adreno: Add support for Adreno 510 GPU")
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/526898/
Link: https://lore.kernel.org/r/20230314221757.13096-1-a39.skl@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The runtime PM status can only be updated while runtime PM is disabled.
Drop the bogus pm_runtime_set_active() call that was made after enabling
runtime PM and which (incidentally but correctly) left the runtime PM
status set to 'suspended'.
Fixes: 2c087a3366 ("drm/msm/adreno: Load the firmware before bringing up the hardware")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/524972/
Link: https://lore.kernel.org/r/20230303164807.13124-4-johan+linaro@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
A recent commit moved enabling of runtime PM to GPU load time (first
open()) but failed to update the error paths so that runtime PM is
disabled if initialisation of the GPU fails. This would trigger a
warning about the unbalanced disable count on the next open() attempt.
Note that pm_runtime_put_noidle() is sufficient to balance the usage
count when pm_runtime_put_sync() fails (and is chosen over
pm_runtime_resume_and_get() for consistency reasons).
Fixes: 4b18299b33 ("drm/msm/adreno: Defer enabling runpm until hw_init()")
Cc: stable@vger.kernel.org # 6.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/524971/
Link: https://lore.kernel.org/r/20230303164807.13124-3-johan+linaro@kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Matthew Wilcox (Oracle)