Naveen Mamindlapalli says:
====================
Add tc hardware offloads
This patch series adds support for tc hardware offloads.
Patch #1 adds support for offloading flows that matches IP tos and IP
protocol which will be used by tc hw offload support. Also
added ethtool n-tuple filter to code to offload the flows
matching the above fields.
Patch #2 adds tc flower hardware offload support on ingress traffic.
Patch #3 adds TC flower offload stats.
Patch #4 adds tc TC_MATCHALL egress ratelimiting offload.
* tc flower hardware offload in PF driver
The driver parses the flow match fields and actions received from the tc
subsystem and adds/delete MCAM rules for the same. Each flow contains set
of match and action fields. If the action or fields are not supported,
the rule cannot be offloaded to hardware. The tc uses same set of MCAM
rules allocated for ethtool n-tuple filters. So, at a time only one entity
can offload the flows to hardware, they're made mutually exclusive in the
driver.
Following match and actions are supported.
Match: Eth dst_mac, EtherType, 802.1Q {vlan_id,vlan_prio}, vlan EtherType,
IP proto {tcp,udp,sctp,icmp,icmp6}, IPv4 tos, IPv4{dst_ip,src_ip},
L4 proto {dst_port|src_port number}.
Actions: drop, accept, vlan pop, redirect to another port on the device.
The Hardware stats are also supported. Currently only packet counter stats
are updated.
* tc egress rate limiting support
Added TC-MATCHALL classifier offload with police action applied for all
egress traffic on the specified interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC_MATCHALL egress ratelimiting offload support with POLICE
action for entire traffic going out of the interface.
Eg: To ratelimit egress traffic to 100Mbps
$ ethtool -K eth0 hw-tc-offload on
$ tc qdisc add dev eth0 clsact
$ tc filter add dev eth0 egress matchall skip_sw \
action police rate 100Mbit burst 16Kbit
HW supports a max burst size of ~128KB.
Only one ratelimiting filter can be installed at a time.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get the stats for tc flower flows that are
offloaded to hardware. To support this feature, added a
new AF mbox handler which returns the MCAM entry stats
for a flow that has hardware stat counter enabled.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc flower hardware offload on ingress
traffic. Since the tc-flower filter rules use the same set of MCAM
rules as the n-tuple filters, the n-tuple filters and tc flower
rules are mutually exclusive. When one of the feature is enabled
using ethtool, the other feature is disabled in the driver. By default
the driver enables n-tuple filters during initialization.
The following flow keys are supported.
-> Ethernet: dst_mac
-> L2 proto: all protocols
-> VLAN (802.1q): vlan_id/vlan_prio
-> IPv4: dst_ip/src_ip/ip_proto{tcp|udp|sctp|icmp}/ip_tos
-> IPv6: ip_proto{icmpv6}
-> L4(tcp/udp/sctp): dst_port/src_port
The following flow actions are supported.
-> drop
-> accept
-> redirect
-> vlan pop
The flow action supports multiple actions when vlan pop is specified
as the first action. The redirect action supports redirecting to the
PF/VF of same PCI device. Redirecting to other PCI NIX devices is not
supported.
Example #1: Add a tc filter rule to drop UDP traffic with dest port 80
# ethtool -K eth0 hw-tc-offload on
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: flower ip_proto \
udp dst_port 80 action drop
Example #2: Add a tc filter rule to redirect ingress traffic on eth0
with vlan id 3 to eth6 (ex: eth0 vf0) after stripping the vlan hdr.
# ethtool -K eth0 hw-tc-offload on
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 parent ffff: protocol 802.1Q flower \
vlan_id 3 vlan_ethtype ipv4 action vlan pop action mirred \
ingress redirect dev eth6
Example #3: List the ingress filter rules
# tc -s filter show dev eth4 ingress
Example #4: Delete tc flower filter rule with handle 0x1
# tc filter del dev eth0 ingress protocol ip pref 49152 \
handle 1 flower
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for programming the HW MCAM match key with IP tos, IP(v6)
proto icmp/icmpv6, allowing flow offload rules to be installed using
those fields. The NPC HW extracts layer type, which will be used as a
matching criteria for different IP protocols.
The ethtool n-tuple filter logic has been updated to parse the IP tos
and l4proto for HW offloading. l4proto tcp/udp/sctp/ah/esp/icmp are
supported. See example usage below.
Ex: Redirect l4proto icmp to vf 0 queue 0
ethtool -U eth0 flow-type ip4 l4proto 1 action vf 0 queue 0
Ex: Redirect flow with ip tos 8 to vf 0 queue 0
ethtool -U eth0 flow-type ip4 tos 8 vf 0 queue 0
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, e.g., the ZynqMP, devm_clk_get can return
-EPROBE_DEFER if the clock controller, which is implemented in firmware,
has not been probed yet.
As clk_init is only called during probe, use dev_err_probe to simplify
the error message and hide it for -EPROBE_DEFER.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún says:
====================
Add support for mv88e6393x family of Marvell
after 2 months I finally had time to send v17 of Amethyst patches.
This series is tested on Marvell CN9130-CRB.
Changes since v16:
- dropped patches adding 5gbase-r, since they are already merged
- rebased onto net-next/master
- driver API renamed set_egress_flood() method into 2 methods for
ucast/mcast floods, so this is fixed
Changes from v15:
- put 10000baseKR_Full back into phylink_validate method for Amethyst,
it seems I misunderstood the meaning behind things and removed it
from v15
- removed erratum 3.7, since the procedure is done anyway in
mv88e6390_serdes_pcs_config
- renumbered errata 3.6 and 3.8 to 4.6 and 4.8, according to newer
version of the errata document
- refactored errata code a little and removed duplicate macro
definitions (for example MV88E6390_SGMII_CONTROL is already called
MV88E6390_SGMII_BMCR)
Changes from v14:
- added my Signed-off-by tags to Pavana's patches, since I am sending
them (as suggested by Andrew)
- added documentation to second patch adding 5gbase-r mode (as requested
by Russell)
- added Reviewed-by tags
- applied Vladimir's suggestions:
- reduced indentation level in mv88e6xxx_set_egress_port and
mv88e6393x_serdes_port_config
- removed 10000baseKR_Full from mv88e6393x_phylink_validate
- removed PHY_INTERFACE_MODE_10GKR from mv88e6xxx_port_set_cmode
Changes from v13:
- added patch that wraps .set_egress_port into mv88e6xxx_set_egress_port,
so that we do not have to set chip->*gress_dest_port members in every
implementation of this method
- for the patch that adds Amethyst support:
- added more information into commit message
- added these methods for mv88e6393x_ops:
.port_sync_link
.port_setup_message_port
.port_max_speed_mode (new implementation needed)
.atu_get_hash
.atu_set_hash
.serdes_pcs_config
.serdes_pcs_an_restart
.serdes_pcs_link_up
- this device can set upstream port per port, so implement
.port_set_upstream_port
instead of
.set_cpu_port
- removed USXGMII cmode (not yet supported, working on it)
- added debug messages into mv88e6393x_port_set_speed_duplex
- added Amethyst errata 4.5 (EEE should be disabled on SERDES ports)
- fixed 5gbase-r serdes configuration and interrupt handling
- refactored mv88e6393x_serdes_setup_errata
- refactored mv88e6393x_port_policy_write
- added patch implementing .port_set_policy for Amethyst
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16-bit Port Policy CTL register from older chips is on 6393x changed
to Port Policy MGMT CTL, which can access more data, but indirectly and
via 8-bit registers.
The original 16-bit value is divided into first two 8-bit register in
the Port Policy MGMT CTL.
We can therefore use the previous code to compute the mask and shift,
and then
- if 0 <= shift < 8, we access register 0 in Port Policy MGMT CTL
- if 8 <= shift < 16, we access register 1 in Port Policy MGMT CTL
There are in fact other possible policy settings for Amethyst which
could be added here, but this can be done in the future.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6393X device is a single-chip integration of a 11-port
Ethernet switch with eight integrated Gigabit Ethernet (GbE)
transceivers and three 10-Gigabit interfaces.
This patch adds functionalities specific to mv88e6393x family (88E6393X,
88E6193X and 88E6191X).
The main differences between previous devices and this one are:
- port 0 can be a SERDES port
- all SERDESes are one-lane, eg. no XAUI nor RXAUI
- on the other hand the SERDESes can do USXGMII, 10GBASER and 5GBASER
(on 6191X only one SERDES is capable of more than 1g; USXGMII is not
yet supported with this change)
- Port Policy CTL register is changed to Port Policy MGMT CTL register,
via which several more registers can be accessed indirectly
- egress monitor port is configured differently
- ingress monitor/CPU/mirror ports are configured differently and can be
configured per port (ie. each port can have different ingress monitor
port, for example)
- port speed AltBit works differently than previously
- PHY registers can be also accessed via MDIO address 0x18 and 0x19
(on previous devices they could be accessed only via Global 2 offsets
0x18 and 0x19, which means two indirections; this feature is not yet
leveraged with thiis commit)
Co-developed-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Co-developed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two implementations of the .set_egress_port method, and both
of them, if successful, set chip->*gress_dest_port variable.
To avoid code repetition, wrap this method into
mv88e6xxx_set_egress_port.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 is no more an error case with MV88E6393 family
which has serdes lane numbers 0, 9 or 10.
So with this change .serdes_get_lane will return lane number
or -errno (-ENODEV or -EOPNOTSUPP).
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending the driver to support per-queue RX and TX coalesce settings in
order to support below commands:
To show per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --show-coalesce
To set per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --coalesce \
[rx-usecs N] [rx-frames M] [tx-usecs P] [tx-frames Q]
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
DSA/switchdev documentation fixups
These are some small fixups after the recently merged documentation
update.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9d5ef190e5 ("net: dsa: automatically bring up DSA master
when opening user port"), DSA manages the administrative status of the
host port automatically. Update the configuration steps to reflect this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains:
configuration.rst:165: WARNING: duplicate label networking/dsa/configuration:single port, other instance in (...)
configuration.rst:212: WARNING: duplicate label networking/dsa/configuration:bridge, other instance in (...)
configuration.rst:252: WARNING: duplicate label networking/dsa/configuration:gateway, other instance in (...)
And for good reason, because the "single port", "bridge" and "gateway"
use cases are replicated twice, once for normal taggers and twice for
DSA_TAG_PROTO_NONE. So when trying to reference these sections via a
hyperlink such as:
https://www.kernel.org/doc/html/latest/networking/dsa/configuration.html#single-port
it will always reference the first occurrence, and never the second one.
This change makes the "single port", "bridge" and "gateway"
configuration examples consistent with the formatting used in the
"Configuration showcases" subsection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" produces these warnings:
Documentation/networking/dsa/dsa.rst:468: WARNING: Unexpected indentation.
Documentation/networking/dsa/dsa.rst:477: WARNING: Block quote ends without a blank line; unexpected unindent.
Fixes: 8411abbcad ("Documentation: networking: dsa: mention integration with devlink")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though this is clear from the context, it is nice to actually be
grammatically correct.
Fixes: 0f22ad45f4 ("Documentation: networking: switchdev: clarify device driver behavior")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like "make htmldocs" produces this warning:
Documentation/networking/switchdev.rst:482: WARNING: Unexpected indentation.
Fixes: 0f22ad45f4 ("Documentation: networking: switchdev: clarify device driver behavior")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen Mamindlapalli says:
====================
refactor code related to npc install flow
This patchset refactors and cleans up the code associated with the
npc install flow API, specifically to eliminate different code paths
while installing MCAM rules by AF and PF. This makes the code easier
to understand and maintain. Also added support for multi channel NIX
promisc entry.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mbox handler npc_install_flow returns ENOTSUPP for unsupported
flow keys. This patch modifies the return value to AF driver defined
error code for debugging purpose.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mcam rule described by mcam_rule struct has all the info
such as the hardware MCAM entry number, match criteria and
corresponding action etc. All mcam rules are stored in a
linked list mcam->rules. When adding/updating a rule to the
mcam->rules it is checked if a rule already exists for the
mcam entry. If the rule already exists, the same rule is
updated instead of creating new rule. This way only one
mcam_rule exists for the only one default unicast entry
installed by AF. But a PF/VF can get different NIXLF
(or default unicast entry number) after a attach-detach-attach
sequence. When that happens mcam_rules list end up with two
default unicast rules. Fix the problem by deleting the default
unicast rule list node always when disabling mcam rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use npc_install_flow mailbox API for installing the default promisc
and broadcast match entries. Earlier these entries were installed
using low level npc_config_mcam_entry API, which does not store these
rules and is not available when the rules are dumped using debugfs.
Added chan_mask field to npc_install_flow_req to calculate channel
mask when channel count is greater than 1 and configure the channel
mask in entry kw_mask.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for multi channel NIX promisc entry. Packets sent
on all those channels by the host should be received by the interface to
which those channels belong. Channel count, if greater than 1, should be
power of 2 as only one promisc entry is available for the interface. Key
mask is modified such that incoming packets from channel base to channel
count are directed to the same pci function.
Signed-off-by: Nalla, Pradeep <pnalla@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors npc_install_flow function to install AF
installed default MCAM entries similar to other MCAM entries
installed by PF/VF. As a result the code would be more readable
and easy to maintain. Modified npc_verify_entry and npc_verify_channel
to properly check MCAM rules installed by AF.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: Allow 802.1d and .1ad VxLAN bridges to coexist on Spectrum>=2
Ido Schimmel says:
====================
This patchset allows user space to simultaneously configure both 802.1d
and 802.1ad VxLAN bridges on Spectrum-2 and later ASICs. 802.1ad VxLAN
bridges are still forbidden on Spectrum-1.
The reason for the current limitation is that up until now the EtherType
that was pushed to decapsulated VxLAN packets was a property of the
tunnel port, of which there is only one. This meant that a 802.1ad VxLAN
bridge could not be configured if the tunnel port was already configured
to push a 802.1q tag.
This patchset improves the situation by making two changes. First,
decapsulated packets are marked as having their EtherType decided by the
egress port. Second, local ports member in the bridge (e.g., swp1) are
configured to set the correct egress EtherType.
Patchset overview:
Patch #1 adds a register required for the first change
Patches #2-#3 add the register required for the second change and a
corresponding API
Patch #4 prepares the driver for the split in behavior between
Spectrum-1 and later ASICs
Patch #5 performs the two above mentioned changes to allow the driver to
support simultaneous 802.1ad and 802.1d VxLAN bridges on Spectrum-2 and
later ASICs
Patch #6 adds a selftest
Patch #7 removes a selftest that verified the limitation that was lifted
by this patchset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
q_in_vni_veto.sh is not needed anymore because VxLAN with an 802.1ad
bridge and VxLAN with an 802.1d bridge can coexist.
Remove the test.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure VxLAN with an 802.1ad bridge and VxLAN with an 802.1d bridge
at the same time in same switch, verify that traffic passed as expected.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only one EtherType can be configured for pushing in tunnels
because EtherType is configured using SPVID.et_vlan for tunnel port.
This behavior is forbidden by comparing mlxsw_sp_nve_config struct for
each new tunnel, the struct contains 'ethertype' field which means that
only one EtherType is legal at any given time. Remove 'ethertype' field to
allow creating VxLAN devices with different bridges.
To allow using several types of VxLAN bridges at the same time, the
EtherType should be determined at the egress port. This behavior is
achieved by setting SPVID to decide which EtherType to push at egress and
for each local_port which is member in 802.1ad bridge, set SPEVET.et_vlan
to ether_type1 (i.e., 0x88A8).
Use switchdev_ops->init() to set different mlxsw_sp_bridge_ops for
different ASICs in order to be able to split the behavior when port joins /
leaves an 802.1ad bridge in different ASICs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A subsequent patch will need to implement different set of operations
when a port joins / leaves an 802.1ad bridge, based on the ASIC type.
Prepare for this change by allowing to initialize the bridge module
based on the ASIC type via 'struct mlxsw_sp_switchdev_ops'.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A subsequent patch will cause decapsulated packets to have their EtherType
determined by the egress port. Add mlxsw_sp_port_egress_ethtype_set() which
will be called when a port joins an 802.1ad bridge, so that it will set an
802.1ad EtherType on decapsulated packets transmitted through it, instead
of the default 802.1q EtherType.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPEVET configures which EtherType to push at egress for packets incoming
through a local port for which 'SPVID.egr_et_set' is set.
The next patches will use SPEVET to configure EtherType 0x88A8 and
0x8100 for local ports member in 802.1ad and 802.1q bridges,
respectively. This allows using dual VxLAN bridges (802.1d and 802.1ad at
the same time).
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPVID.egr_et_set=1 means that when VLAN is pushed at ingress (for untagged
packets or for QinQ push mode) then the EtherType is decided at the egress
port.
The next patches will use this field for VxLAN devices (tunnel port) in
order to allow using dual VxLAN bridges (802.1d and 802.1ad at the same
time).
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Álvaro Fernández Rojas says:
====================
net: dsa: b53: support legacy tags
Legacy Broadcom tags are needed for older switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for legacy Broadcom tags, which are similar to DSA_TAG_PROTO_BRCM.
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/procesing/processing/
s/comparations/comparisons/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM63xx switches are present on bcm63xx and bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: cleanups and simplifications
We do a number of cleanups and simplifications, especially regarding
call signatures in the binding table. This makes the code easier to
understand and serves as preparation for upcoming functional additions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We move some warning printouts to more strategic locations to avoid
duplicates and yield more detailed information about the reported
problem.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reduce and localize the usage of the tipc_sub_xx() macros by adding a
corresponding member, with fields set in host-endian format, to struct
tipc_subscription.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_report_overlap() is called from the binding table
with numerous parameters taken from an instance of struct publication.
A closer look reveals that it always is safe to send along a pointer
to the instance itself, and hence reduce the call signature. We do
that in this commit.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reduce the signature of tipc_find_service() and
tipc_create_service(). The reason for doing this might not
be obvious, but we plan to let struct tipc_uaddr contain
information that is relevant for these functions in a later
commit.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the signatures of the functions tipc_service_create_range()
and tipc_service_find_range().
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reduce the signature of tipc_nametbl_lookup_group() by using a
struct tipc_uaddr pointer. This entails a couple of minor changes in the
functions tipc_send_group_mcast/anycast/unicast/bcast() in socket.c
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We follow up the preceding commits by reducing the signature of
the function tipc_nametbl_lookup_mcast_nodes().
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reduce the signature of this function according to the same
principle as the preceding commits.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the signature if function tipc_nametbl_lookup_anycast(),
using address structures instead of discrete integers.
This also makes it possible to make some improvements to the functions
__tipc_sendmsg() in socket.c and tipc_msg_lookup_dest() in msg.c.
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
