Commit Graph

17 Commits

Author SHA1 Message Date
Mika Westerberg 952400756d net: thunderbolt: Align the driver to the USB4 networking spec
The USB4 networking spec (USB4NET) recommends different timeouts, and
also suggest that the driver sets the 64k frame support flag in the
properties block. Make the networking driver to honor this.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2021-03-18 18:25:31 +03:00
Mika Westerberg 180b068942 thunderbolt: Allow multiple DMA tunnels over a single XDomain connection
Currently we have had an artificial limitation of a single DMA tunnel
per XDomain connection. However, hardware wise there is no such limit
and software based connection manager can take advantage of all the DMA
rings available on the host to establish tunnels.

For this reason make the tb_xdomain_[enable|disable]_paths() to take the
DMA ring and HopID as parameter instead of storing them in the struct
tb_xdomain. We also add API functions to allocate input and output
HopIDs of the XDomain connection that the service drivers can use
instead of hard-coding.

Also convert the two existing service drivers over to this API.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2021-03-18 18:25:31 +03:00
Linus Torvalds 0cee54c890 USB / Thunderbolt patches for 5.11-rc1
Here is the big USB and thunderbolt pull request for 5.11-rc1.
 
 Nothing major in here, just the grind of constant development to support
 new hardware and fix old issues:
   - thunderbolt updates for new USB4 hardware
   - cdns3 major driver updates
   - lots of typec updates and additions as more hardware is available
   - usb serial driver updates and fixes
   - other tiny USB driver updates
 
 All have been in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iKFQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yme2gCfacEYztlnc0fh7PyyatYXgdkspbYAn2ri6mfF
 4VY86HYXKqQRDW8w/lSg
 =f8KJ
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / Thunderbolt updates from Greg KH:
 "Here is the big USB and thunderbolt pull request for 5.11-rc1.

  Nothing major in here, just the grind of constant development to
  support new hardware and fix old issues:

   - thunderbolt updates for new USB4 hardware

   - cdns3 major driver updates

   - lots of typec updates and additions as more hardware is available

   - usb serial driver updates and fixes

   - other tiny USB driver updates

  All have been in linux-next with no reported issues"

* tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
  usb: phy: convert comma to semicolon
  usb: ucsi: convert comma to semicolon
  usb: typec: tcpm: convert comma to semicolon
  usb: typec: tcpm: Update vbus_vsafe0v on init
  usb: typec: tcpci: Enable bleed discharge when auto discharge is enabled
  usb: typec: Add class for plug alt mode device
  USB: typec: tcpci: Add Bleed discharge to POWER_CONTROL definition
  USB: typec: tcpm: Add a 30ms room for tPSSourceOn in PR_SWAP
  USB: typec: tcpm: Fix PR_SWAP error handling
  USB: typec: tcpm: Hard Reset after not receiving a Request
  USB: gadget: f_fs: remove likely/unlikely
  usb: gadget: f_fs: Re-use SS descriptors for SuperSpeedPlus
  USB: gadget: f_midi: setup SuperSpeed Plus descriptors
  USB: gadget: f_acm: add support for SuperSpeed Plus
  USB: gadget: f_rndis: fix bitrate for SuperSpeed and above
  usb: typec: intel_pmc_mux: Configure cable generation value for USB4
  MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
  usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
  usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
  usb: cdns3: fix NULL pointer dereference on no platform data
  ...
2020-12-15 13:54:56 -08:00
Zheng Yongjun 201d126a63 net: thunderbolt: convert comma to semicolon
Replace a comma between expression statements by a semicolon.

Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-12-09 16:23:08 -08:00
Mika Westerberg afe704a2d0 thunderbolt: Add support for end-to-end flow control
USB4 spec defines end-to-end (E2E) flow control that can be used between
hosts to prevent overflow of a RX ring. We previously had this partially
implemented but that code was removed with commit 53f13319d1
("thunderbolt: Get rid of E2E workaround") with the idea that we add it
back properly if there ever is need. Now that we are going to add DMA
traffic test driver (in subsequent patches) this can be useful.

For this reason we modify tb_ring_alloc_rx/tx() so that they accept
RING_FLAG_E2E and configure the hardware ring accordingly. The RX side
also requires passing TX HopID (e2e_tx_hop) used in the credit grant
packets.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-11 10:20:16 +03:00
Linus Torvalds 47ec5303d7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from David Miller:

 1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.

 2) Support UDP segmentation in code TSO code, from Eric Dumazet.

 3) Allow flashing different flash images in cxgb4 driver, from Vishal
    Kulkarni.

 4) Add drop frames counter and flow status to tc flower offloading,
    from Po Liu.

 5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.

 6) Various new indirect call avoidance, from Eric Dumazet and Brian
    Vazquez.

 7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
    Yonghong Song.

 8) Support querying and setting hardware address of a port function via
    devlink, use this in mlx5, from Parav Pandit.

 9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.

10) Switch qca8k driver over to phylink, from Jonathan McDowell.

11) In bpftool, show list of processes holding BPF FD references to
    maps, programs, links, and btf objects. From Andrii Nakryiko.

12) Several conversions over to generic power management, from Vaibhav
    Gupta.

13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
    Yakunin.

14) Various https url conversions, from Alexander A. Klimov.

15) Timestamping and PHC support for mscc PHY driver, from Antoine
    Tenart.

16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.

17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.

18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.

19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
    drivers. From Luc Van Oostenryck.

20) XDP support for xen-netfront, from Denis Kirjanov.

21) Support receive buffer autotuning in MPTCP, from Florian Westphal.

22) Support EF100 chip in sfc driver, from Edward Cree.

23) Add XDP support to mvpp2 driver, from Matteo Croce.

24) Support MPTCP in sock_diag, from Paolo Abeni.

25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
    infrastructure, from Jakub Kicinski.

26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.

27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.

28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.

29) Refactor a lot of networking socket option handling code in order to
    avoid set_fs() calls, from Christoph Hellwig.

30) Add rfc4884 support to icmp code, from Willem de Bruijn.

31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.

32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.

33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.

34) Support TCP syncookies in MPTCP, from Flowian Westphal.

35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
    Brivio.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
  net: thunderx: initialize VF's mailbox mutex before first usage
  usb: hso: remove bogus check for EINPROGRESS
  usb: hso: no complaint about kmalloc failure
  hso: fix bailout in error case of probe
  ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
  selftests/net: relax cpu affinity requirement in msg_zerocopy test
  mptcp: be careful on subflow creation
  selftests: rtnetlink: make kci_test_encap() return sub-test result
  selftests: rtnetlink: correct the final return value for the test
  net: dsa: sja1105: use detected device id instead of DT one on mismatch
  tipc: set ub->ifindex for local ipv6 address
  ipv6: add ipv6_dev_find()
  net: openvswitch: silence suspicious RCU usage warning
  Revert "vxlan: fix tos value before xmit"
  ptp: only allow phase values lower than 1 period
  farsync: switch from 'pci_' to 'dma_' API
  wan: wanxl: switch from 'pci_' to 'dma_' API
  hv_netvsc: do not use VF device if link is down
  dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
  net: macb: Properly handle phylink on at91sam9x
  ...
2020-08-05 20:13:21 -07:00
Mika Westerberg 547030c8e6 net: thunderbolt: Add comment clarifying prtcstns flags
ThunderboltIP protocol currently has two flags from which we only
support and set match frags ID. The first flag is reserved for full E2E
flow control. Add a comment that clarifies them.

Suggested-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-23 20:36:02 -07:00
Mika Westerberg 53f13319d1 thunderbolt: Get rid of E2E workaround
The end-to-end (E2E) workaround is needed for Falcon Ridge (TBT 2)
controller when E2E is enabled for both ends of the host-to-host
connection. However, we never supported full E2E in the first place so
this code is not necessary at the moment. Further this allows us to use
all available rings for data except ring 0 which is reserved for the
control path.

The complete E2E flow control is explained in the USB4 spec so we may
add it back later if needed but at least the networking driver seems to
work fine without, and the higher level stack, like TCP will retransmit
lost packets anyway.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2020-06-22 19:58:06 +03:00
Jonathan Lemon b54c9d5bd6 net: Use skb_frag_off accessors
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.

Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-30 14:21:32 -07:00
Mika Westerberg 9872760eb7 net: thunderbolt: Unregister ThunderboltIP protocol handler when suspending
The XDomain protocol messages may start as soon as Thunderbolt control
channel is started. This means that if the other host starts sending
ThunderboltIP packets early enough they will be passed to the network
driver which then gets confused because its resume hook is not called
yet.

Fix this by unregistering the ThunderboltIP protocol handler when
suspending and registering it back on resume.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
2019-04-18 11:18:51 +03:00
Mika Westerberg 7e3af59368 net: thunderbolt: Convert to use SPDX identifier
This gets rid of the licence boilerblate in favor of SPDX identifier
which only takes a single line comment.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-08-29 19:43:21 -07:00
Mika Westerberg 027d351c54 net: thunderbolt: Run disconnect flow asynchronously when logout is received
The control channel calls registered callbacks when control messages
such as XDomain protocol messages are received. The control channel
handling is done in a worker running on system workqueue which means the
networking driver can't run tear down flow which includes sending
disconnect request and waiting for a reply in the same worker. Otherwise
reply is never received (as the work is already running) and the
operation times out.

To fix this run disconnect ThunderboltIP flow asynchronously once
ThunderboltIP logout message is received.

Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-12 12:03:04 -05:00
Mika Westerberg 8e021a14d9 net: thunderbolt: Tear down connection properly on suspend
When suspending to mem or disk the Thunderbolt controller typically goes
down as well tearing down the connection automatically. However, when
suspend to idle is used this does not happen so we need to make sure the
connection is properly disconnected before it can be re-established
during resume.

Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-12 12:03:04 -05:00
Mika Westerberg 540c11159d net: thunderbolt: Stop using zero to mean no valid DMA mapping
Commit 86dabda426 ("net: thunderbolt: Clear finished Tx frame bus
address in tbnet_tx_callback()") fixed a DMA-API violation where the
driver called dma_unmap_page() in tbnet_free_buffers() for a bus address
that might already be unmapped. The fix was to zero out the bus address
of a frame in tbnet_tx_callback().

However, as pointed out by David Miller, zero might well be valid
mapping (at least in theory) so it is not good idea to use it here.

It turns out that we don't need the whole map/unmap dance for Tx buffers
at all. Instead we can map the buffers when they are initially allocated
and unmap them when the interface is brought down. In between we just
DMA sync the buffers for the CPU or device as needed.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-25 23:56:02 +09:00
Mika Westerberg 86dabda426 net: thunderbolt: Clear finished Tx frame bus address in tbnet_tx_callback()
When Thunderbolt network interface is disabled or when the cable is
unplugged the driver releases all allocated buffers by calling
tbnet_free_buffers() for each ring. This function then calls
dma_unmap_page() for each buffer it finds where bus address is non-zero.
Now, we only clear this bus address when the Tx buffer is sent to the
hardware so it is possible that the function finds an entry that has
already been unmapped.

Enabling DMA-API debugging catches this as well:

  thunderbolt 0000:06:00.0: DMA-API: device driver tries to free DMA
    memory it has not allocated [device address=0x0000000068321000] [size=4096 bytes]

Fix this by clearing the bus address of a Tx frame right after we have
unmapped the buffer.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-11 19:20:45 +09:00
Dan Carpenter fa31f0c98d thunderbolt: Right shifting to zero bug in tbnet_handle_packet()
There is a problem when we do:

	sequence = pkg->hdr.length_sn & TBIP_HDR_SN_MASK;
	sequence >>= TBIP_HDR_SN_SHIFT;

TBIP_HDR_SN_SHIFT is 27, and right shifting a u8 27 bits is always
going to result in zero.  The fix is to declare these variables as u32.

Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-19 13:04:32 +01:00
Amir Levy e69b6c02b4 net: Add support for networking over Thunderbolt cable
ThunderboltIP is a protocol created by Apple to tunnel IP/ethernet
traffic over a Thunderbolt cable. The protocol consists of configuration
phase where each side sends ThunderboltIP login packets (the protocol is
determined by UUID in the XDomain packet header) over the configuration
channel. Once both sides get positive acknowledgment to their login
packet, they configure high-speed DMA path accordingly. This DMA path is
then used to transmit and receive networking traffic.

This patch creates a virtual ethernet interface the host software can
use in the same way as any other networking interface. Once the
interface is brought up successfully network packets get tunneled over
the Thunderbolt cable to the remote host and back.

The connection is terminated by sending a ThunderboltIP logout packet
over the configuration channel. We do this when the network interface is
brought down by user or the driver is unloaded.

Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-02 11:24:42 -07:00