Increase inbox and outbox mailbox size from 512 to 1024 to
support thirdparty DTS integration ipc tx/rx messages communication.
This is done through firmware window get info.
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220913144319.1055302-5-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add pci driver and platform driver to enable SOF support on ACP6x
architecture based Rembrandt platform.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220913144319.1055302-3-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer AMD SOC differs slightly in terms of few registers offset and
configuration. Add offsets into chip_info struct to make core ACP
code more generic and resusable on newer SOC.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220913144319.1055302-2-Vsujithkumar.Reddy@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The new IPC4 version is only supported by Intel platforms, iMX, AMD and
MediaTek only uses the standard SOF IPC.
There is no need for these platforms to build kernel support for IPC4 as
it is just dead code for them.
SND_SOC_SOF_IPC3 and SND_SOC_SOF_INTEL_IPC4 is introduced to allow compile
time selection and exclusion of IPC implementations.
To avoid randconfig failures add also support for runtime selection of
the IPC ops in ipc.c based on sdev->pdata->ipc_type
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220614075618.28605-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SOF PM ops callback in renoir dsp ops to power off and on ACP
IP block during system suspend and resume on Renoir platform.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220606210212.146626-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop host code (AMD, Intel) to access sdev->dmatb directly.
Modify the trace_init prototype to include the pointer to a
struct snd_dma_buffer. The ipc3-dtrace passes for now the pointer to
sdev->dmatb, but the aim is to move all tracing related runtime information
local to a trace implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220516104711.26115-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The used firmware loader (snd_sof_load_firmware_memcpy) can use the generic
module loading, which is by default uses the same implementation as the
snd_sof_parse_module_memcpy.
No need to set the callback for this platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220425221129.124615-6-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fw_ready is handled internally to ipc3 and the callback no longer in
use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Ajit Pandey <ajitkumar.pandey@amd.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220421080735.31698-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are currently using generic PSP Mailbox register for sending SHA
complete command to PSP but observe random arbitration issue during
PSP validation as MP0_C2PMSG_26_REG used by other kernel modules.
Use separate mailbox registers and doorbell mechanism to send SHA_DMA
complete command to PSP. This fixes such validation issues and added
flexibility for sending more ACP commands to PSP in future as new mbox
registers i.e MP0_C2PMSG_114_REG and MP0_C2PMSG_73_REG are dedicated
by PSP for ACP communications.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220421165820.337207-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to ensure if PSP is mbox ready before and after sending cmd
to PSP over SMN interface. Add method to check MBOX_READY bit of PSP
with some delay over ACP_PSP_TIMEOUT_COUNTER. Replace psp_fw_validate
with new method psp_send_cmd() to send command via psp mailbox.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220421165820.337207-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we start having multiple platforms with minor variants, the
use of the const qualifier for 'dsp_ops' is starting to be
sub-optimal: the structures are copied across platforms, with only a
couple of members that differ.
This patch removes the const qualifier without any functionality
changes, and adds an optional initialization callback. In follow-up
patches, the dsp_ops will revisited for Intel HDaudio platforms, with
the differences added programmatically over a common baseline.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220414184817.362215-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid misleading file names, use different names for INTEL_IPC4
firmware files.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Link: https://lore.kernel.org/r/20220414184817.362215-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a default IPC type for each platform, along with file
paths to be used for each IPC type. To make reviews simpler, we only
modify platform descriptors in this table, the information will be
used in the next patch.
The Intel IPCv4 is only supported on Intel platforms after APL, and
not by default. In follow-up patches, support for SKL and KBL will be
added, and in those two cases the IPCv4 will be the default (and only
supported mode).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220414184817.362215-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the addition of the IPCv4, we need the ability to select
different paths for firmware and topologies.
First add an indirection. Follow-up patches will add mechanisms to
select a default IPC or override it.
No functionality change in this patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220414184817.362215-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not send IPC structure directly via pcm_hw_params to make it IPC
agnostic.
A new struct is created to retrieve the needed platform parameters and if
there is a need it can be extended with new options.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220310042720.976809-3-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Host is trying to acquire semaphore lock based on HW_SEM_RETRY_COUNT
value which is set to 10 by default. So host will loop for 10 times
trying to acquire lock before giving error msg "Failed to acquire HW
lock". Though this loop count of 10 is good enough with most of the
times but we have observed such failure msg in very few cases(~5 %).
Increase ACP_HW_SEM_RETRY_COUNT to avoid such issue and loop for a
significant time period before throwing error. We're setting newer
loop count to quite higher value of 10K but it's very unlikely that
it will loop for this count, since for most of the cases lock will
get acquired at much lesser loop iterations.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We are using PTE_GRP1 for DMA operations to load firmware binaries
but we are enabling PTE_GRP and flushing ATU cache much before in
probe callbacks. This can cause issue if we try to load firmware
runtime during system resume as probe callback will not be invoked
hence PTE_GRP will not be enabled. Moreover it makes more sense to
flush the cache after register configuration.
Move PTE group register configuration to acp-loader within pre_fw_run
callback to avoid such issue.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add lock and unlock around ipc irq handling code using hw semaphore
register that exhibit special property for register read calls. As
host and DSP firmware uses few shared registers, there is a possible
race condition around those shared registers values. This lock ensure
synchronization between Firmware and host ipc interrupts.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP_SRAM_PTE block has cache that needs to be flushed after every
PTE updates. This patch updates ACPAXI2AXI_ATU_CTRL register to
flush cache after updating PTE with stream physical address.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ipc_pcm_params() ops implementation for AMD is a NOP and since the
callback is marked now as optional, it can be dropped along with the
empty function.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using the values from ipc_params, take them directly from
substream->runtime.
This is in preparation of making the platform hw_params callback to be
IPC agnostic.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304205733.62233-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a pointer to the stream_tag within the
struct sof_ipc_dma_trace_params_ext, pass the pointer to the containing
struct.
AMD needs to update buffer.phy_addr (and don't really use the stream_tag)
for the trace implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220128123623.23569-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
cppcheck warning:
sound/soc/sof/amd/acp.c:222:9: warning: Identical condition and return
expression 'ret', return value is always 0
[identicalConditionAfterEarlyExit]
return ret;
^
sound/soc/sof/amd/acp.c:213:6: note: If condition 'ret' is true, the
function will return/exit
if (ret)
^
sound/soc/sof/amd/acp.c:222:9: note: Returning identical expression 'ret'
return ret;
^
Just return 0; on success.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Link: https://lore.kernel.org/r/20211221165802.236843-1-AjitKumar.Pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add callback to notify PSP after loading firmware on DSP. PSP will
validate the loaded firmware and set qualifier bit to run firmware
on secured AMD systems.
Signed-off-by: Julian Schroeder <Julian.Schroeder@amd.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Curtis Malainey <curtis@malainey.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-14-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add trace support and configure trace stream for ACP firmware.
Signed-off-by: Vishnuvardhanrao Ravuapati <vishnuvardhanrao.ravulapati@amd.com>
Signed-off-by: V sujith kumar Reddy <vsreddy@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-13-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI driver module to enable sof pci device support for Renoir.
If machine flag set to FLAG_SOF_ONLY_DMIC this pci driver register
platform device for non dsp based I2S platform device. If machine
flag is not enabled for SOF pci probe will return without invoking
sof device probe and registration
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-10-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add module to support ALSA pcm stream configurations for ACP I2S
and DMIC endpoints
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-7-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add dsp ops callback to register I2S and DMIC sof dai's with ALSA
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-6-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add IPC module for generic ACP block and exposed ops callback for
to synchronize SOF IPC message between host and DSP
Signed-off-by: Balakishore Pati <Balakishore.pati@amd.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-5-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add acp-loader module with ops callback to load and run firmware
on ACP DSP block on Renoir platform.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-4-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP DMA is used for loading SOF firmware into DSP memory and data
transfer from system memory to DSP memory. Add helper callbacks to
initialize and configure ACP DMA block for fw loading.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-3-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch initializes ACP HW block to support SOF on
AMD Renoir platform.
Signed-off-by: Ajit Kumar Pandey <AjitKumar.Pandey@amd.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20211117093734.17407-2-daniel.baluta@oss.nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
