[ Upstream commit 79f5962bae ]
The maximum MTU was set to 2304, which is the maximum MSDU size. While
this is valid for normal WLAN interfaces, it is too low for monitor
interfaces. A monitor interface may receive and inject MPDU frames, and
the maximum MPDU frame size is larger than 2304. The MPDU may also
contain an A-MSDU frame, in which case the size may be much larger than
the MTU limit. Since the maximum size of an A-MSDU depends on the PHY
mode of the transmitting STA, it is not possible to set an exact MTU
limit for a monitor interface. Now the maximum MTU for a monitor
interface is unrestricted.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123246.2070558-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5d3cbdb09 ]
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d656a4c6ea ]
If we have been keeping per-CPU statistics, consider them
regardless of USES_RSS, because we may not actually fill
those, for example in non-fast-RX cases when the connection
is not compatible with fast-RX. If we didn't fill them, the
additional data will be zero and not affect anything, and
if we did fill them then it's more correct to consider them.
This fixes an issue in mesh mode where some statistics are
not updated due to USES_RSS being set, but fast-RX isn't
used.
Reported-by: Thiraviyam Mariyappan <tmariyap@codeaurora.org>
Link: https://lore.kernel.org/r/20210610220814.13b35f5797c5.I511e9b33c5694e0d6cef4b6ae755c873d7c22124@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 744757e46b ]
Remove the remaining workaround that is not removed by the
commit e41eb3e408 ("mac80211: remove iwlwifi specific workaround
that broke sta NDP tx")
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210623134826.10318-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e41eb3e408 upstream.
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 652e8363bb ]
Various elements are parsed with a requirement to have an
exact size, when really we should only check that they have
the minimum size that we need. Check only that and therefore
ignore any additional data that they might carry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.cd101f8040a4.Iadf0e9b37b100c6c6e79c7b298cc657c2be9151a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc6f03ff2 ]
Apparently we never clear these values, so they'll remain set
since the setting of them is conditional. Clear the values in
the relevant other cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.316e32d136a9.I2a12e51814258e1e1b526103894f4b9f19a91c8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bddc0c411a upstream.
The commit cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx
queue") moved the code to validate the radiotap header from
ieee80211_monitor_start_xmit to ieee80211_parse_tx_radiotap. This made is
possible to share more code with the new Tx queue selection code for
injected frames. But at the same time, it now required the call of
ieee80211_parse_tx_radiotap at the beginning of functions which wanted to
handle the radiotap header. And this broke the rate parser for radiotap
header parser.
The radiotap parser for rates is operating most of the time only on the
data in the actual radiotap header. But for the 802.11a/b/g rates, it must
also know the selected band from the chandef information. But this
information is only written to the ieee80211_tx_info at the end of the
ieee80211_monitor_start_xmit - long after ieee80211_parse_tx_radiotap was
already called. The info->band information was therefore always 0
(NL80211_BAND_2GHZ) when the parser code tried to access it.
For a 5GHz only device, injecting a frame with 802.11a rates would cause a
NULL pointer dereference because local->hw.wiphy->bands[NL80211_BAND_2GHZ]
would most likely have been NULL when the radiotap parser searched for the
correct rate index of the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: cb17ed29a7 ("mac80211: parse radiotap header when selecting Tx queue")
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
[sven@narfation.org: added commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20210530133226.40587-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e298aa358f ]
Replace hard-coded compile-time constants for header length check
with dynamic determination based on the frame type. Otherwise, we
hit a validation WARN_ON in cfg80211 later.
Fixes: cd418ba63f ("mac80211: convert S1G beacon to scan results")
Reported-by: syzbot+405843667e93b9790fc1@syzkaller.appspotmail.com
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210510041649.589754-1-ducheng2@gmail.com
[style fixes, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3edc6b0d6c upstream.
For some chips/drivers, e.g., QCA6174 with ath10k, the decryption is
done by the hardware, and the Protected bit in the Frame Control field
is cleared in the lower level driver before the frame is passed to
mac80211. In such cases, the condition for ieee80211_has_protected() is
not met in ieee80211_rx_h_defragment() of mac80211 and the new security
validation steps are not executed.
Extend mac80211 to cover the case where the Protected bit has been
cleared, but the frame is indicated as having been decrypted by the
hardware. This extends protection against mixed key and fragment cache
attack for additional drivers/chips. This fixes CVE-2020-24586 and
CVE-2020-24587 for such cases.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.037aa5ca0390.I7bb888e2965a0db02a67075fcb5deb50eb7408aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c4d76a8d upstream.
EAPOL frames are used for authentication and key management between the
AP and each individual STA associated in the BSS. Those frames are not
supposed to be sent by one associated STA to another associated STA
(either unicast for broadcast/multicast).
Similarly, in 802.11 they're supposed to be sent to the authenticator
(AP) address.
Since it is possible for unexpected EAPOL frames to result in misbehavior
in supplicant implementations, it is better for the AP to not allow such
cases to be forwarded to other clients either directly, or indirectly if
the AP interface is part of a bridge.
Accept EAPOL (control port) frames only if they're transmitted to the
own address, or, due to interoperability concerns, to the PAE group
address.
Disable forwarding of EAPOL (or well, the configured control port
protocol) frames back to wireless medium in all cases. Previously, these
frames were accepted from fully authenticated and authorized stations
and also from unauthenticated stations for one of the cases.
Additionally, to avoid forwarding by the bridge, rewrite the PAE group
address case to the local MAC address.
Cc: stable@vger.kernel.org
Co-developed-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.cb327ed0cabe.Ib7dcffa2a31f0913d660de65ba3c8aca75b1d10f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf30ca922a upstream.
As pointed out by Mathy Vanhoef, we implement the RX PN check
on fragmented frames incorrectly - we check against the last
received PN prior to the new frame, rather than to the one in
this frame itself.
Prior patches addressed the security issue here, but in order
to be able to reason better about the code, fix it to really
compare against the current frame's PN, not the last stored
one.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.bfbc340ff071.Id0b690e581da7d03d76df90bb0e3fd55930bc8a0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a11ce08c4 upstream.
Prior patches protected against fragmentation cache attacks
by coloring keys, but this shows that it can lead to issues
when multiple stations use the same sequence number. Add a
fragment cache to struct sta_info (in addition to the one in
the interface) to separate fragments for different stations
properly.
This then automatically clear most of the fragment cache when a
station disconnects (or reassociates) from an AP, or when client
interfaces disconnect from the network, etc.
On the way, also fix the comment there since this brings us in line
with the recommendation in 802.11-2016 ("An AP should support ...").
Additionally, remove a useless condition (since there's no problem
purging an already empty list).
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.fc35046b0d52.I1ef101e3784d13e8f6600d83de7ec9a3a45bcd52@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 270032a2a9 upstream.
With old ciphers (WEP and TKIP) we shouldn't be using A-MSDUs
since A-MSDUs are only supported if we know that they are, and
the only practical way for that is HT support which doesn't
support old ciphers.
However, we would normally accept them anyway. Since we check
the MMIC before deaggregating A-MSDUs, and the A-MSDU bit in
the QoS header is not protected in TKIP (or WEP), this enables
attacks similar to CVE-2020-24588. To prevent that, drop A-MSDUs
completely with old ciphers.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.076543300172.I548e6e71f1ee9cad4b9a37bf212ae7db723587aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1d5ff5651 upstream.
Properly parse A-MSDUs whose first 6 bytes happen to equal a rfc1042
header. This can occur in practice when the destination MAC address
equals AA:AA:03:00:00:00. More importantly, this simplifies the next
patch to mitigate A-MSDU injection attacks.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.0b2b886492f0.I23dd5d685fe16d3b0ec8106e8f01b59f499dffed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94034c40ab upstream.
Simultaneously prevent mixed key attacks (CVE-2020-24587) and fragment
cache attacks (CVE-2020-24586). This is accomplished by assigning a
unique color to every key (per interface) and using this to track which
key was used to decrypt a fragment. When reassembling frames, it is
now checked whether all fragments were decrypted using the same key.
To assure that fragment cache attacks are also prevented, the ID that is
assigned to keys is unique even over (re)associations and (re)connects.
This means fragments separated by a (re)association or (re)connect will
not be reassembled. Because mac80211 now also prevents the reassembly of
mixed encrypted and plaintext fragments, all cache attacks are prevented.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.3f8290e59823.I622a67769ed39257327a362cfc09c812320eb979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 965a7d72e7 upstream.
Do not mix plaintext and encrypted fragments in protected Wi-Fi
networks. This fixes CVE-2020-26147.
Previously, an attacker was able to first forward a legitimate encrypted
fragment towards a victim, followed by a plaintext fragment. The
encrypted and plaintext fragment would then be reassembled. For further
details see Section 6.3 and Appendix D in the paper "Fragment and Forge:
Breaking Wi-Fi Through Frame Aggregation and Fragmentation".
Because of this change there are now two equivalent conditions in the
code to determine if a received fragment requires sequential PNs, so we
also move this test to a separate function to make the code easier to
maintain.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.30c4394bb835.I5acfdb552cc1d20c339c262315950b3eac491397@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6843d1ee2 ]
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db878e27a9 ]
If any of the cipher schemes specified by the driver are invalid, bail
out and fail the registration rather than just warning. Otherwise, we
might later crash when we try to use the invalid cipher scheme, e.g.
if the hdr_len is (significantly) less than the pn_offs + pn_len, we'd
have an out-of-bounds access in RX validation.
Fixes: 2475b1cc0d ("mac80211: add generic cipher scheme support")
Link: https://lore.kernel.org/r/20210408143149.38a3a13a1b19.I6b7f5790fa0958ed8049cf02ac2a535c61e9bc96@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd0b455381 ]
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1153a74768 upstream.
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4 ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d73cd946d upstream.
The incorrect timeout check caused probing to happen when it did
not need to happen. This in turn caused tx performance drop
for around 5 seconds in ath10k-ct driver. Possibly that tx drop
is due to a secondary issue, but fixing the probe to not happen
when traffic is running fixes the symptom.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 041c881a0b ]
Even if the first channel from sband channel list is invalid
or disabled mac80211 ends up choosing it as the default channel
for monitor interfaces, making them not usable.
Fix this by assigning the first available valid or enabled
channel instead.
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
Link: https://lore.kernel.org/r/1615440547-7661-1-git-send-email-kathirve@codeaurora.org
[reword commit message, comment, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58d25626f6 ]
crypto_aead_encrypt returns <0 on error, so if these calls are not checked,
execution may continue with failed encrypts. It also seems that these two
crypto_aead_encrypt calls are the only instances in the codebase that are
not checked for errors.
Signed-off-by: Daniel Phan <daniel.phan36@gmail.com>
Link: https://lore.kernel.org/r/20210309204137.823268-1-daniel.phan36@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f7e90fadd ]
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80d ("mac80211: refactor extended element parsing")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1944015fe9 ]
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d333 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e72 ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6194f7e647 ]
The multiplication of the u32 variables tx_time and estimated_retx is
performed using a 32 bit multiplication and the result is stored in
a u64 result. This has a potential u32 overflow issue, so avoid this
by casting tx_time to a u64 to force a 64 bit multiply.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 050ac52cbe ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210205175352.208841-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b64acb28da ]
When CONFIG_ATH9K is built-in but LED support is in a loadable
module, both ath9k drivers fails to link:
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_deinit_leds':
gpio.c:(.text+0x36): undefined reference to `led_classdev_unregister'
x86_64-linux-ld: drivers/net/wireless/ath/ath9k/gpio.o: in function `ath_init_leds':
gpio.c:(.text+0x179): undefined reference to `led_classdev_register_ext'
The problem is that the 'imply' keyword does not enforce any dependency
but is only a weak hint to Kconfig to enable another symbol from a
defconfig file.
Change imply to a 'depends on LEDS_CLASS' that prevents the incorrect
configuration but still allows building the driver without LED support.
The 'select MAC80211_LEDS' is now ensures that the LED support is
actually used if it is present, and the added Kconfig dependency
on MAC80211_LEDS ensures that it cannot be enabled manually when it
has no effect.
Fixes: 197f466e93 ("ath9k_htc: Do not select MAC80211_LEDS by default")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210125113654.2408057-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcf3c8fb32 ]
Upon receiving CSA with 160MHz extended NSS BW from associated AP,
STA should set the HT operation_mode based on new_center_freq_seg1
because it is later used as ccfs2 in ieee80211_chandef_vht_oper().
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20201222064714.24888-1-shay.bar@celeno.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 18fe0fae61 upstream.
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210201083324.3134-1-nbd@nbd.name
[use rcu_access_pointer() instead since we won't dereference here]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b101dd2d22 ]
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 622d3b4e39 ]
When using WEP, the default unicast key needs to be selected, instead of
the STA PTK.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218184718.93650-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6020d534fa ]
This fixes strlen mismatch problems happening in some .write callbacks
of debugfs.
When trying to configure airtime_flags in debugfs, an error appeared:
ash: write error: Invalid argument
The error is returned from kstrtou16() since a wrong length makes it
miss the real end of input string. To fix this, use count as the string
length, and set proper end of string for a char buffer.
The debug print is shown - airtime_flags_write: count = 2, len = 8,
where the actual length is 2, but "len = strlen(buf)" gets 8.
Also cleanup the other similar cases for the sake of consistency.
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://lore.kernel.org/r/20210112032028.7482-1-shayne.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 054c9939b4 ]
syzbot reported a crash that happened when changing the interface
type around a lot, and while it might have been easy to fix just
the symptom there, a little deeper investigation found that really
the reason is that we allowed packets to be transmitted while in
the middle of changing the interface type.
Disallow TX by stopping the queues while changing the type.
Fixes: 34d4bc4d41 ("mac80211: support runtime interface type changes")
Reported-by: syzbot+d7a3b15976bf7de2238a@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210122171115.b321f98f4d4f.I6997841933c17b093535c31d29355be3c0c39628@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c13cf5c159 upstream.
Check if atf has been disabled in __ieee80211_schedule_txq() in order to
avoid a given sta is always put to the beginning of the active_txqs list
and never moved to the end since deficit is not decremented in
ieee80211_sta_register_airtime()
Fixes: b4809e9484 ("mac80211: Add airtime accounting and scheduling to TXQs")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/93889406c50f1416214c079ca0b8c9faecc5143e.1608975195.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2463ec86cd upstream.
ieee80211_tx_h_select_key drops any non-mgmt packets without a key when
encryption is used. This is wrong for nulldata packets that can't be
encrypted and are sent out for probing clients and indicating 4-address
mode.
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Fixes: a0761a3017 ("mac80211: drop data frames without key on encrypted links")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201218191525.1168-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f879ac8ed6 ]
It should be !is_multicast_ether_addr() in ieee80211_rx_h_sta_process()
for the rx_stats update, below commit remove the !, this patch is to
change it back.
It lead the rx rate "iw wlan0 station dump" become invalid for some
scenario when IEEE80211_HW_USES_RSS is set.
Fixes: 09a740ce35 ("mac80211: receive and process S1G beacons")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1607483189-3891-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f65607cdbc ]
When we set up a TDLS station, we set sta->sta.bandwidth solely based
on the capabilities, because the "what's the current bandwidth" check
is bypassed and only applied for other types of stations.
This leads to the unfortunate scenario that the sta->sta.bandwidth is
160 MHz if both stations support it, but we never actually configure
this bandwidth unless the AP is already using 160 MHz; even for wider
bandwidth support we only go up to 80 MHz (at least right now.)
For iwlwifi, this can also lead to firmware asserts, telling us that
we've configured the TX rates for a higher bandwidth than is actually
available due to the PHY configuration.
For non-TDLS, we check against the interface's requested bandwidth,
but we explicitly skip this check for TDLS to cope with the wider BW
case. Change this to
(a) still limit to the TDLS peer's own chandef, which gets factored
into the overall PHY configuration we request from the driver,
and
(b) limit it to when the TDLS peer is authorized, because it's only
factored into the channel context in this case.
Fixes: 504871e602 ("mac80211: fix bandwidth computation for TDLS peers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.fcc7d29c4590.I11f77e9e25ddf871a3c8d5604650c763e2c5887a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
During restarrt, mac80211 is supposed to reconfigure the driver.
When there's a monitor interface, the interface is added and the
channel context for it was created, but not assigned to it as it
was not considered running during the restart.
Fix this by setting SDATA_STATE_RUNNING while adding monitor
interfaces.
Signed-off-by: Borwankar, Antara <antara.borwankar@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.e1df99693a4c.I494579f28018c2d0b9d4083a664cf872c28405ae@changeid
[reword commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_chandef_he_6ghz_oper() needs to return true if it
determined a value 6 GHz chandef, fix that.
Fixes: 1d00ce807e ("mac80211: support S1G association")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1606121152-3452-1-git-send-email-wgong@codeaurora.org
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers fill the status rate list without setting the rate index after
the final rate to -1. minstrel_ht already deals with this, but minstrel
doesn't, which causes it to get stuck at the lowest rate on these drivers.
Fix this by checking the count as well.
Cc: stable@vger.kernel.org
Fixes: cccf129f82 ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Deferring sampling attempts to the second stage has some bad interactions
with drivers that process the rate table in hardware and use the probe flag
to indicate probing packets (e.g. most mt76 drivers). On affected drivers
it can lead to probing not working at all.
If the link conditions turn worse, it might not be such a good idea to
do a lot of sampling for lower rates in this case.
Fix this by simply skipping the sample attempt instead of deferring it,
but keep the checks that would allow it to be sampled if it was skipped
too often, but only if it has less than 95% success probability.
Also ensure that IEEE80211_TX_CTL_RATE_CTRL_PROBE is set for all probing
packets.
Cc: stable@vger.kernel.org
Fixes: cccf129f82 ("mac80211: add the 'minstrel' rate control algorithm")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Fixes: 3318111cf6 ("mac80211: reduce duplication in tx status functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20201111183359.43528-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
