There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.
Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.
While merging the code patch does following functional changes:
- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
was used for platform and ACPI devices but PCI device used
"i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
printed in case of error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.
There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").
This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.
The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.
As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
The dma_mapping_error() function returns true if there is an error, it
doesn't return an error code. We should return -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When occur i2c ack error, i2c controller generate two interrupts,
first is the ack error interrupt, then the complete interrupt.
i2c interrupt handler should keep the two interrupt value, and only
call complete() for the complete interrupt.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reset DMA in hardware init function to avoid unknown hardware state
before do any I2C operation.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.
In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Minor clean up of indenting, no functional change
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[wsa: squashed two lines into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The owner of the adapter is missing, while this driver is tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Printing adapter name is irrelevant from this debug print and makes output
needlessly long. Having already device and functions names printed here is
enough for debugging.
While at it remove extra space from "enabled= 0x" and use "%#x" for
printing "0x" prefixed hexadecimal values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made it a oneliner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for VCT-jig parallel port I2C adapter to i2c-parport.
The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborki
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.
Add support to configure clock divisor register of I2C controller
based on bus clock rate.
This clock divisor is supported form T114 onwards.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.
It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming
This mechanism is supported on T124 and after this SoCs.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:
drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.
Handle error cases in the Rx path
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the busy loop while waiting for bus busy.
Instead let the processor sleep.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.
In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch cleans up i2c_pxa_probe() function,
- Use devm_ variants wherever
This will clean both probe exit and i2c_pxa_remove() functions
- Check platform resource before parsing any other data from DT/platform
- Use dev_err on failure from i2c_add_numbered_adapter()
- Use pr_info instead of printk for KERN_INFO
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix below warning message, coming from 64 bit toolchain.
drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.
Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.
For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.
This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
there's no need to fetch the platform_device
in order to dereference it back to the dev
pointer to access drvdata, we can use
dev_get_drvdata() instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Start using pr_fmt and convert all remaining printk to use
pr_* family of macros.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
[wsa: remove print on kzalloc failure]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now parport is using device model so use dev_* macros instead of printk.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.
As a precaution, reset all these bits to their default values after
recovery is complete.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
=H5wD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ofUZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Here are the changes for MMC for v4.2.
MMC core:
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation"
* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
mmc: queue: prevent soft lockups on PREEMPT=n
mmc: mediatek: Add PM support for MMC driver
mmc: mediatek: Add Mediatek MMC driver
mmc: dt-bindings: add Mediatek MMC bindings
mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
mmc: sdhci: fix low memory corruption
mmc: sdhci-pci: Change AMD SDHCI quirk application scope
i2c-piix4: Use Macro for AMD CZ SMBus device ID
pci_ids: Add AMD KERNCZ device ID support
mmc: queue: use swap() in mmc_queue_thread()
mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
mmc: sdhci: Restore behavior while creating OCR mask
mmc: sdhci-pxav3: fix device wakeup initialization
mmc: core: Attach PM domain prior probing of SDIO func driver
mmc: core: Remove redundant ->power_restore() callback for SD
mmc: core: Remove redundant ->power_restore() callback for MMC
mmc: sdhci-bcm2835: Actually enable the clock
mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
mmc: sdhci-of-esdhc: enable interrupt mode to detect card
mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
...
Checks if the cdiv value is in between min (0x2) and max (0xFFFE)
supported values by the bcm2835. If not, it returns -ENODEV.
See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
[wsa: resolved a merge conflict]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver calls pm_runtime_put() right before pm_runtime_disable() in its
->remove() hook to make sure clock is gated etc. However, it turns out that
pm_runtime_put() only calls ->idle() hook without actually suspending
anything. The following pm_runtime_disable() will prevent the driver from
suspending thus leaving it "active".
It is better to suspend the device synchronously to make sure it is
actually suspended before disabling runtime PM from it.
While there, undo call to pm_runtime_use_autosuspend().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
payload_size is a 12 bit field in the HW register, so add a limit for
this size. That way we gracefully reject the message beforehand instead
of generating an OOPS while transferring. Verified using some older
Tegra2 documentation and a more recent Jetson TK1 board.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
This HW cannot send 0-byte-length messages and the driver discards them.
So, we should not advertise SMBUS_QUICK.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'commit 2637e5fd23 ("i2c: octeon: Fix i2c fail problem when a process is
terminated by a signal")' removed the wait_event_interruptible_timeout to
prevent half/mixed i2c messages from being sent/recievd but forgot to
drop the signal handling case in the return handling. This just removes
this dead code. While at it the return variable is adjusted to the type
expected.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several cases where current clock configuration algorithm produces
not optimal results:
- truncation in "clk" calculation leads to the fact that actual BUS frequency
will be always higher than spec except two exact module frequences 8MHz and
12MHz in the whole 7-12MHz range of permitted frequences
- driver configures SCL HIGH to LOW ratio always 1 to 1 and this doesn't work
well in 400kHz case, namely minimum time of LOW state (according to I2C Spec
2.1) 1.3us will not be fulfilled. HIGH to LOW ratio 1 to 2 would be more
approriate here.
Signed-off-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The datasheet mentions on page 31 that the bits 10-31 must be read as
don't care and written as 0.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
We cannot guarantee that we read bits 10-31 as always 0 (because the
datasheet says read as don't care). We clear the bits with a bitmask to
prevent writing back unknown data at the reserved bits.
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This used to be in platform init code. We want it to do in the driver
now. This is basically a code move and a new compatible added.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change AMD CZ SMBUS device ID from 0x790b to
use Macro definition
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
buf_len is a size_t, so unsigned, but was tested with '<= 0'.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe
function. It was incorrectly defined with __init declaration.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sending a message to own address locks the controller up in very bizarre state,
it behaves as slave even if MDR register clearly states master. The controller
remains in this state until reset. To avoid unnecessary timeouts simply avoid
sending to own address. The controller cannot do this any way. Also, do not
enable AAS IRQ, as the slave mode is not supported by the driver and the only
possibility to trigger this IRQ is to send to own address.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several problems in the function:
- "to_cnt" variable does nothing
- schedule_timeout() call without setting current state does nothing
- "allow_sleep" parameter is not really used
Refactor the function so that it really tries to wait. In case of timeout try
to recover the bus.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When FIFOs are available and enabled, the driver now configures the Atmel
eXtended DMA Controller to perform word accesses instead of byte accesses
when possible.
The actual access width depends on the size of the buffer to transmit.
To enable FIFO support the "atmel,fifo-size" property must be set properly
in the I2C controller node of the device tree.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe() function now prints the hardware version of the I2C
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[wsa: s/version/hw version/] for clarity]
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The alternative command mode was introduced to simplify the transmission
of STOP conditions and to solve timing and latency issues around them.
This mode relies on a new register, the Alternative Command Register,
which must be set at the same time as the Master Mode Register. This new
register was designed to allow simple setup of basic combined transactions
built from up to two unitary transactions.
Indeed, the ACR is split into two areas, which describe one unitary
transaction each. Each area is filled with Data Length 8bit counter, a
Direction and a PEC Request bit. The PEC bit is only used in SMBus mode
and is not supported by this driver yet. Also when using alternative
command mode, the MREAD bit from the Master Mode Register is ignored.
Instead the Direction bits from ACR are used to setup the direction, read
or write, of each unitary transaction. Finally the 8bit counters must
filled with the data length of their respective transaction. Then if only
one transaction is to be used, the data length of the second one must be
set to zero. At the moment, this driver uses only the first transaction.
In addition to MMR and ACR, the Control Register also need to be written
to enable the alternative command mode. That's the purpose of its ACMEN
bit, which stands for Alternative Command Mode Enable.
Note that the alternative command mode is compatible with the use of the
Internal Address Register. So combined transactions for eeprom read are
actually implemented with the Internal Address Register. This register is
written with up to 3 bytes, which are the internal address sent to the
slave through the first write transaction. Then the first area of the ACR
describe the write transaction to follow, which carries the data to be
read from the eeprom. The second area of the ACR is not used so its Data
Length 8bit counter is cleared.
For each byte sent or received by the device, the Data Length 8bit counter
is decremented. When it reaches 0, a STOP condition is automatically sent.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch just fixes typo before applying later patches which will use
register bits with index above 16.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.
In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().
Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.
For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cc: stable@vger.kernel.org #3.10 and later
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add suspend/resume support to the Broadcom iProc I2C driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1fc2fe204c ("i2c: designware: Add runtime PM hooks") adds
runtime pm support using the same ops for system pm and runtime pm.
When suspend to ram, the i2c host may have been runtime suspended, thus
i2c_dw_disable() hangs.
Previously, I fixed this issue by separating ops for system pm and
runtime pm, then in the system suspend/resume path, runtime pm apis are
used to ensure the device is at correct state.
But as Mika Westerberg pointed out: it sounds a bit silly to resume the
device just because you want to call i2c_dw_disable() for it before
suspending again. He then suggested an elegant solution which keeps the
device runtime suspended during system suspend with the help of
'dev->power.direct_complete'. This patch adopted this solution, and in
fact Mika provided the main code.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use recovery framework and implement bus recovery using "Bus Monitor" register.
Tests show that shortening SDA to GND results in "completion" timeout with
"BUSY" bit still set, so initiate recovery in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
