[ Upstream commit b34b9547ce ]
The prescaler in the "Global Timer Control Register bit assignments" is
documented to use bits [15:8], which means that the maximum prescaler
register value is 0xff.
Fixes: 171b45a4a7 ("clocksource/drivers/arm_global_timer: Implement rate compensation whenever source clock changes")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240218174138.1942418-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d3bc4c02d ]
On SAM9 hardware two cascaded 16 bit timers are used to form a 32 bit
high resolution timer that is used as scheduler clock when the kernel
has been configured that way (CONFIG_ATMEL_CLOCKSOURCE_TCB).
The driver initially triggers a reset-to-zero of the two timers but this
reset is only performed on the next rising clock. For the first timer
this is ok - it will be in the next 60ns (16MHz clock). For the chained
second timer this will only happen after the first timer overflows, i.e.
after 2^16 clocks (~4ms with a 16MHz clock). So with other words the
scheduler clock resets to 0 after the first 2^16 clock cycles.
It looks like that the scheduler does not like this and behaves wrongly
over its lifetime, e.g. some tasks are scheduled with a long delay. Why
that is and if there are additional requirements for this behaviour has
not been further analysed.
There is a simple fix for resetting the second timer as well when the
first timer is reset and this is to set the ATMEL_TC_ASWTRG_SET bit in
the Channel Mode register (CMR) of the first timer. This will also rise
the TIOA line (clock input of the second timer) when a software trigger
respective SYNC is issued.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20231007161803.31342-1-rwahl@gmx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b5bf64c89 ]
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Fixes: e932900a32 ("arm: zynq: Use standard timer binding")
Fixes: 70504f311d ("clocksource/drivers/cadence_ttc: Convert init function to return error")
Signed-off-by: Feng Mingxi <m202271825@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230425065611.702917-1-m202271825@hust.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb73556386 ]
Smatch reports:
drivers/clocksource/timer-davinci.c:332 davinci_timer_register()
warn: 'base' from ioremap() not released on lines: 274.
Fix this and other potential memory leak problems
by adding a set of corresponding exit lables.
Fixes: 721154f972 ("clocksource/drivers/davinci: Add support for clockevents")
Signed-off-by: Qinrun Dai <flno@hust.edu.cn>
Link: https://lore.kernel.org/r/20230413135037.1505799-1-flno@hust.edu.cn
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 180d35a7c0 ]
If clk_get_rate() fails which is called after clk_prepare_enable(),
clk_disable_unprepare() need be called in error path to disable the
clock in dmtimer_systimer_init_clock().
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221029114427.946520-1-yangyingliang@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f44f7156f ]
Documentation for most CMTs say that it takes two input clocks before
changes propagate to the timer. This is especially relevant when the timer
is stopped to change further settings.
Implement the delays according to the spec. To avoid unnecessary delays in
atomic mode, also check if the to-be-written value actually differs.
CMCNT is a bit special because testing showed that it requires 3 cycles to
propagate, which affects all CMTs. Also, the WRFLAG needs to be checked
before writing. This fixes "cannot clear CMCNT" messages which occur often
on R-Car Gen4 SoCs, but only very rarely on older SoCs for some reason.
Fixes: 81b3b27110 ("clocksource: sh_cmt: Add support for multiple channels per device")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20221130210609.7718-1-wsa+renesas@sang-engineering.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f15a9de4 ]
This reverts commit 232ccac1bd.
On the subject of suspend, the RISC-V SBI spec states:
This does not cover whether any given events actually reach the hart or
not, just what the hart will do if it receives an event. On PolarFire
SoC, and potentially other SiFive based implementations, events from the
RISC-V timer do reach a hart during suspend. This is not the case for the
implementation on the Allwinner D1 - there timer events are not received
during suspend.
To fix this, the CLOCK_EVT_FEAT_C3STOP (mis)feature was enabled for the
timer driver - but this has broken both RCU stall detection and timers
generally on PolarFire SoC and potentially other SiFive based
implementations.
If an AXI read to the PCIe controller on PolarFire SoC times out, the
system will stall, however, with CLOCK_EVT_FEAT_C3STOP active, the system
just locks up without RCU stalling:
io scheduler mq-deadline registered
io scheduler kyber registered
microchip-pcie 2000000000.pcie: host bridge /soc/pcie@2000000000 ranges:
microchip-pcie 2000000000.pcie: MEM 0x2008000000..0x2087ffffff -> 0x0008000000
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: axi read request error
microchip-pcie 2000000000.pcie: axi read timeout
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
microchip-pcie 2000000000.pcie: sec error in pcie2axi buffer
microchip-pcie 2000000000.pcie: ded error in pcie2axi buffer
Freeing initrd memory: 7332K
Similarly issues were reported with clock_nanosleep() - with a test app
that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250 & the blamed
commit in place, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Fortunately, the D1 has a second timer, which is "currently used in
preference to the RISC-V/SBI timer driver" so a revert here does not
hurt operation of D1 in its current form.
Ultimately, a DeviceTree property (or node) will be added to encode the
behaviour of the timers, but until then revert the addition of
CLOCK_EVT_FEAT_C3STOP.
Fixes: 232ccac1bd ("clocksource/drivers/riscv: Events are stopped during CPU suspend")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/
Link: https://github.com/riscv-non-isa/riscv-sbi-doc/issues/98/
Link: https://lore.kernel.org/linux-riscv/bf6d3b1f-f703-4a25-833e-972a44a04114@sholland.org/
Link: https://lore.kernel.org/r/20221122121620.3522431-1-conor.dooley@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit 41929c9f62
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 245b993d8f ]
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
arch/x86/kernel/cpu/mshyperv.c is never compiled as modular.
(CONFIG_HYPERVISOR_GUEST is boolean)
Fixes: dd2cb34861 ("clocksource/drivers: Continue making Hyper-V clocksource ISA agnostic")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20220606050238.4162200-1-masahiroy@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98399cbc1 ]
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220506162522.3675399-1-andre.przywara@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 232ccac1bd ]
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b0194368 ("clocksource: new RISC-V SBI timer driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a861abcee ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
The __setup() handler interface isn't meant to handle negative return
values -- they are non-zero, so they mean "handled" (like a return
value of 1 does), but that's just a quirk. So return 1 from
parse_pmtmr(). Also print a warning message if kstrtouint() returns
an error.
Fixes: 6b148507d3 ("pmtmr: allow command line override of ioport")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4467b8bad2 ]
of_base->base can either be iomapped using of_io_request_and_map() or
of_iomap() depending whether or not an of_base->name has been set.
Thus check of_base->base against NULL as of_iomap() does not return a
PTR_ERR() in case of error.
Fixes: 9aea417afa ("clocksource/drivers/timer-of: Don't request the resource by name")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Link: https://lore.kernel.org/r/20220307172656.4836-1-granquet@baylibre.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab8da93dc0 ]
The driver statically defines maximum number of interrupts it can
handle, however it does not respect that limit when configuring them.
When provided with a DTS with more interrupts than assumed, the driver
will overwrite static array mct_irqs leading to silent memory
corruption.
Validate the interrupts coming from DTS to avoid this. This does not
change the fact that such DTS might not boot at all, because it is
simply incompatible, however at least some warning will be printed.
Fixes: 36ba5d527e ("ARM: EXYNOS: add device tree support for MCT controller driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220220103815.135380-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cd925a882 ]
Move interrupts allocation from exynos4_timer_resources() into separate
function together with the interrupt number parsing code from
mct_init_dt(), so the code for managing interrupts is kept together.
While touching exynos4_timer_resources() function, move of_iomap() to it.
No functional changes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211101193531.15078-2-semen.protsenko@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8840f5460a ]
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389db
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23885389db ]
Commit e428e250fd ("ARM: dts: Configure system timers for omap3")
caused a timer regression for beagleboard revision c where the system
clockevent stops working if omap3isp module is unloaded.
Turns out we still have beagleboard revisions a-b4 capacitor c70 quirks
applied that limit the usable timers for no good reason. This also affects
the power management as we use the system clock instead of the 32k clock
source.
Let's fix the issue by adding a new omap3-beagle-ab4.dts for the old timer
quirks. This allows us to remove the timer quirks for later beagleboard
revisions. We also need to update the related timer quirk check for the
correct compatible property.
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Cc: linux-kernel@vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a663bd1911 upstream.
The driver refuses to probe with -EINVAL since the commit 5d9814df0a
("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock
available").
Before the driver used to probe successfully if either "clock-freq" or
"clock-frequency" properties has been specified in the device tree.
That commit changed
if (A && B)
panic("No clock nor clock-frequency property");
into
if (!A && !B)
return 0;
That's a bug: the reverse of `A && B` is '!A || !B', not '!A && !B'
Signed-off-by: Vadim V. Vlasov <vadim.vlasov@elpitech.ru>
Signed-off-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Fixes: 5d9814df0a ("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock available").
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vadim V. Vlasov <vadim.vlasov@elpitech.ru>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20211109153401.157491-1-asheplyakov@basealt.ru
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eda9a4f7af ]
When building OMAP_DM_TIMER without TIMER_OF, there are orphan sections
due to the use of TIMER_OF_DELCARE() without CONFIG_TIMER_OF. Select
CONFIG_TIMER_OF when enaling OMAP_DM_TIMER:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ti-dm-systimer.o' being placed in section `__timer_of_table'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202108282255.tkdt4ani-lkp@intel.com/
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210828175747.3777891-1-keescook@chromium.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=mKyO
-----END PGP SIGNATURE-----
Merge tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- converted Pistachio platform to use MIPS generic kernel
- fixes and cleanups
* tag 'mips_5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (29 commits)
MIPS: Malta: fix alignment of the devicetree buffer
MIPS: ingenic: Unconditionally enable clock of CPU #0
MIPS: mscc: ocelot: mark the phy-mode for internal PHY ports
MIPS: mscc: ocelot: disable all switch ports by default
MAINTAINERS: adjust PISTACHIO SOC SUPPORT after its retirement
MIPS: Return true/false (not 1/0) from bool functions
MIPS: generic: Return true/false (not 1/0) from bool functions
MIPS: Make a alias for pistachio_defconfig
MIPS: Retire MACH_PISTACHIO
MIPS: config: generic: Add config for Marduk board
pinctrl: pistachio: Make it as an option
phy: pistachio-usb: Depend on MIPS || COMPILE_TEST
clocksource/drivers/pistachio: Make it selectable for MIPS
clk: pistachio: Make it selectable for generic MIPS kernel
MIPS: DTS: Pistachio add missing cpc and cdmm
MIPS: generic: Allow generating FIT image for Marduk board
MIPS: locking/atomic: Fix atomic{_64,}_sub_if_positive
MIPS: loongson2ef: don't build serial.o unconditionally
MIPS: Replace deprecated CPU-hotplug functions.
MIPS: Alchemy: Fix spelling contraction "cant" -> "can't"
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmEuJwwTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXp0ICACsx9NtQh1f9xGMClYrbobJfGmiwHVV
uKut/44Vg39tSyZB4mQt3A8YcaQj1Nibo6HVmxJtbKbrKwlTGAiQh5fiOmBOd7Re
/rII/S+CGtAyChI1adHTSL2xdk6WY0c7XQw+IPaERBikG5rO81Y6NLjFZNOv494k
JnG9uGGjAcJWFYylPcLxt4sR/hEfE4KDzsWjWOb5azYgo/RwOan6zYDdkUgocp4A
J+zmgCiME8LLmEV19gn7p4gpX7X9m5mcNgn53eICYPhrBqI0PTWocm6DepCEnrQ+
pEobIagWIMx5Dr7euEJwLxFSN7bdzleVOa4FSfM0zUsEjdbiPH47VQFM
=Vae6
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20210831' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- make Hyper-V code arch-agnostic (Michael Kelley)
- fix sched_clock behaviour on Hyper-V (Ani Sinha)
- fix a fault when Linux runs as the root partition on MSHV (Praveen
Kumar)
- fix VSS driver (Vitaly Kuznetsov)
- cleanup (Sonia Sharma)
* tag 'hyperv-next-signed-20210831' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv_utils: Set the maximum packet size for VSS driver to the length of the receive buffer
Drivers: hv: Enable Hyper-V code to be built on ARM64
arm64: efi: Export screen_info
arm64: hyperv: Initialize hypervisor on boot
arm64: hyperv: Add panic handler
arm64: hyperv: Add Hyper-V hypercall and register access utilities
x86/hyperv: fix root partition faults when writing to VP assist page MSR
hv: hyperv.h: Remove unused inline functions
drivers: hv: Decouple Hyper-V clock/timer code from VMbus drivers
x86/hyperv: add comment describing TSC_INVARIANT_CONTROL MSR setting bit 0
Drivers: hv: Move Hyper-V misc functionality to arch-neutral code
Drivers: hv: Add arch independent default functions for some Hyper-V handlers
Drivers: hv: Make portions of Hyper-V init code be arch neutral
x86/hyperv: fix for unwanted manipulation of sched_clock when TSC marked unstable
asm-generic/hyperv: Add missing #include of nmi.h
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
Just pass bool flags from the different initcalls and use the
flags to set the right pointers. This results in less pointers
passed around in init.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210724224424.2085404-1-linus.walleij@linaro.org
mtk_syst_clkevt_shutdown is called after irq disabled in suspend flow,
clear any pending systimer irq when shutdown to avoid suspend aborted
due to timer irq pending
Also as for systimer in mediatek socs, there must be firstly enable
timer before clear systimer irq
Fixes: e3af677607d9("clocksource/drivers/timer-mediatek: Add support for system timer")
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1617960162-1988-2-git-send-email-Fengquan.Chen@mediatek.com
Use "FIELD_GET()" and "FIELD_PREP()" to simplify the code.
[dlezcano] : Changed title
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1627638188-116163-1-git-send-email-zhouyanjie@wanyeetech.com
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55 ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
The "mct_tick" is a per-cpu clockevents device. Set the
CLOCK_EVT_FEAT_PERCPU feature to prevent e.g. mct_tick0 being unsafely
designated as the global broadcast timer and instead treat the device as
a per-cpu wakeup timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-3-will@kernel.org
All arm64 CPUs feature an architected timer, which offers a relatively
low-latency interface to a per-cpu clocksource and timer. For the most
part, using this interface is a no-brainer, with the exception of SoCs
where it cannot be used to wake up from deep idle state (i.e.
CLOCK_EVT_FEAT_C3STOP is set).
On the contrary, the Exynos MCT is extremely slow to access yet can be
used as a wakeup source. In preparation for using the Exynos MCT as a
potential wakeup timer for the Arm architected timer, reduce its ratings
so that the architected timer is preferred.
This effectively reverts the decision made in 6282edb72b
("clocksource/drivers/exynos_mct: Increase priority over ARM arch timer")
for arm64, as the reasoning for the original change was to work around
a 32-bit SoC design.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> # exynos-5422
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-2-will@kernel.org
So it will be avilable for generic MIPS kernel.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This rewrites the IXP4xx watchdog driver as follows:
- Spawn the watchdog driver as a platform device from the timer
driver. It's one device in the hardware, and the fact that
Linux splits the handling into two different devices is
a Linux pecularity, and thus it becomes a Linux pecularity
to spawn a separate watchdog driver.
- Spawn the watchdog driver from the timer driver at probe().
This is well after the timer driver as actually registered and
started and we know the register base is available.
- Instead of looping back callbacks to the timer drivers for all
watchdog calls, pass the register base to the watchdog driver
and manage the registers there. The two drivers aren't even
interested in the same register so the spinlock is totally
surplus, delete it.
- Replace pretty much all of the content in the watchdog driver
with a simple, modern watchdog driver utilizing the watchdog
core instead of registering its own misc device and ioctl()
handling.
- Drop module parameters as the same already exist in the
watchdog core.
What remains is a slim elegant (IMO) watchdog driver using the
watchdog core, spawning from device tree or boardfile alike.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hyper-V clock/timer code in hyperv_timer.c is mostly independent from
other VMbus drivers, but building for ARM64 without hyperv_timer.c
shows some remaining entanglements. A default implementation of
hv_read_reference_counter can just read a Hyper-V synthetic register
and be independent of hyperv_timer.c, so move this code out and into
hv_common.c. Then it can be used by the timesync driver even if
hyperv_timer.c isn't built on a particular architecture. If
hyperv_timer.c *is* built, it can override with a faster implementation.
Also provide stubs for stimer functions called by the VMbus driver when
hyperv_timer.c isn't built.
No functional changes.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1626220906-22629-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
that's just a bunch of data so the diffstat reflects that. Looking beyond that
there's just a bunch of updates all around in various clk drivers. Renesas and
NXP (for i.MX) are two SoC vendors that have a lot of patches in here. Overall
the driver changes look to be mostly enabling more clks and non-critical fixes
that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates clkdev to be
the only implementation of clk_get() and clk_put(). That's a good step in the
right direction to migreate eveerything over to the common clk framework. Now
we don't have to worry about clkdev specific details, they're just part of the
clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is implemented in
only one place in the kernel instead of in drivers/clk/clkdev.c and in
architectures that want their own implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif, audio,
parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate()
and improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework
-----BEGIN PGP SIGNATURE-----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=YnCF
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
The device is not losing context on CPU_CLUSTER_PM_ERROR. As we are only
saving and restoring context with cpu_pm, there is no need to restore the
context in case of an error.
Note that the unnecessary restoring of context does not cause issues, it's
just not needed.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210518075306.35532-1-tony@atomide.com
Bad counter reads are experienced sometimes when bit 10 or greater rolls
over. Originally, testing showed that at least 10 lower bits would be
set to the same value during these bad reads. However, some users still
reported time skips.
Wider testing revealed that on some chips, occasionally only the lowest
9 bits would read as the anomalous value. During these reads (which
still happen only when bit 10), bit 9 would read as the correct value.
Reduce the mask by one bit to cover these cases as well.
Cc: stable@vger.kernel.org
Fixes: c950ca8c35 ("clocksource/drivers/arch_timer: Workaround for Allwinner A64 timer instability")
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210515021439.55316-1-samuel@sholland.org
Fix the following coccicheck warning:
drivers/clocksource/arm_global_timer.c:107:4-23:
duplicated argument to & or |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210615115440.8881-1-wanjiabing@vivo.com
The sparse tool complains as follows:
drivers/clocksource/arm_global_timer.c:54:23: warning:
symbol 'gt_clk_rate_change_nb' was not declared. Should it be static?
This symbol is not used outside of arm_global_timer.c, so mark it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1623490046-37972-1-git-send-email-zou_wei@huawei.com
Now ARM global timer driver could work even if it's source clock rate
changes, so we don't need to disable that driver when cpu frequency scaling
is in use.
This cause Zynq arch to get support for timer delay and get_cycles().
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210406130045.15491-3-andrea.merello@gmail.com
This patch adds rate change notification support for the parent clock;
should that clock change, then we try to adjust the our prescaler in order
to compensate (i.e. we adjust to still get the same timer frequency).
This is loosely based on what it's done in timer-cadence-ttc. timer-sun51,
mips-gic-timer and smp_twd.c also seem to look at their parent clock rate
and to perform some kind of adjustment whenever needed.
In this particular case we have only one single counter and prescaler for
all clocksource, clockevent and timer_delay, and we just update it for all
(i.e. we don't let it go and call clockevents_update_freq() to notify to
the kernel that our rate has changed).
Note that, there is apparently no other way to fixup things, because once
we call register_current_timer_delay(), specifying the timer rate, it seems
that that rate is not supposed to change ever.
In order for this mechanism to work, we have to make assumptions about how
much the initial clock is supposed to eventually decrease from the initial
one, and set our initial prescaler to a value that we can eventually
decrease enough to compensate. We provide an option in KConfig for this.
In case we end up in a situation in which we are not able to compensate the
parent clock change, we fail returning NOTIFY_BAD.
This fixes a real-world problem with Zynq arch not being able to use this
driver and CPU_FREQ at the same time (because ARM global timer is fed by
the CPU clock, which may keep changing when CPU_FREQ is enabled).
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210406130045.15491-2-andrea.merello@gmail.com
1.Rename the "ingenic_ost_clk_info[]" to "x1000_ost_clk_info[]" to
facilitate the addition of OST support for X2000 SoC in a later
commit
2.When the OST support for X2000 SoC is added, there will be two
compatible strings, so renaming "ingenic_ost_of_match[]" to
"ingenic_ost_of_matches[]" is more reasonable
3.Remove the unnecessary comma in "ingenic_ost_of_matches[]" to reduce
code size as much as possible.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1622824306-30987-2-git-send-email-zhouyanjie@wanyeetech.com
As we are using cpu_pm to save and restore context, we must also save and
restore the timer sysconfig register TIOCP_CFG. This is needed because
we are not calling PM runtime functions at all with cpu_pm.
Fixes: b34677b099 ("clocksource/drivers/timer-ti-dm: Implement cpu_pm notifier for context save and restore")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210415085506.56828-1-tony@atomide.com
Interrupts are disabled during suspend before this driver disables its
timers. ARM trusted firmware will abort suspend if the timer irq is
pending, so ack and disable the timer interrupt during suspend.
Signed-off-by: Evan Benn <evanbenn@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210512122528.v4.1.I1d9917047de06715da16e1620759f703fcfdcbcb@changeid
This option is now synonymous with CONFIG_HAVE_CLK, so use
the latter globally. Any out-of-tree platform ports that
still use a private clk_get()/clk_put() implementation should
move to CONFIG_COMMON_CLK.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Failure of timer initialization is likely to be fatal for the system, so
cleanup in such case is not strictly necessary. However the code might
be refactored or reused, so better not to rely on such assumption that
system won't continue init failure.
Unmap the IO memory and put the clock on initialization failures from
devicetree.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210506202729.157260-3-krzysztof.kozlowski@canonical.com
The 'struct samsung_pwm_variant' argument passed to initialization
functions is not modified, so it can be made const for safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210506202729.157260-2-krzysztof.kozlowski@canonical.com
Cleanup the code to be slightly more readable and follow coding
convention - only whitespace. This fixes checkpatch warnings:
WARNING: Block comments should align the * on each line
WARNING: please, no space before tabs
WARNING: Missing a blank line after declarations
CHECK: Alignment should match open parenthesis
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210506202729.157260-1-krzysztof.kozlowski@canonical.com
Martin Blumenstingl