mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-11-01 00:48:50 +00:00
0c01b20fb5
Add rs485-rts-active-high property, this is a legacy property
used by 8250_omap.
This fixes the following make dt_binding_check warning:
Documentation/devicetree/bindings/serial/8250_omap.yaml:
rs485-rts-active-high: missing type definition
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/all/CAMuHMdUkPiA=o_QLyuwsTYW7y1ksCjHAqyNSHFx2QZ-dP-HGsQ@mail.gmail.com/
Fixes: 403e97d6ab ("dt-bindings: serial: 8250_omap: add rs485-rts-active-high")
Cc: stable <stable@kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231019154834.41721-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
66 lines
2.2 KiB
YAML
66 lines
2.2 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/serial/rs485.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: RS485 serial communications
|
|
|
|
description: The RTS signal is capable of automatically controlling line
|
|
direction for the built-in half-duplex mode. The properties described
|
|
hereafter shall be given to a half-duplex capable UART node.
|
|
|
|
maintainers:
|
|
- Rob Herring <robh@kernel.org>
|
|
|
|
properties:
|
|
rs485-rts-delay:
|
|
description: prop-encoded-array <a b>
|
|
$ref: /schemas/types.yaml#/definitions/uint32-array
|
|
items:
|
|
items:
|
|
- description: Delay between rts signal and beginning of data sent in
|
|
milliseconds. It corresponds to the delay before sending data.
|
|
default: 0
|
|
maximum: 100
|
|
- description: Delay between end of data sent and rts signal in milliseconds.
|
|
It corresponds to the delay after sending data and actual release
|
|
of the line.
|
|
default: 0
|
|
maximum: 100
|
|
|
|
rs485-rts-active-high:
|
|
description: drive RTS high when sending (this is the default).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rts-active-low:
|
|
description: drive RTS low when sending (default is high).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rx-active-high:
|
|
description: Polarity of receiver enable signal (when separate from RTS).
|
|
True indicates active high (default is low).
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
linux,rs485-enabled-at-boot-time:
|
|
description: enables the rs485 feature at boot time. It can be disabled
|
|
later with proper ioctl.
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-rx-during-tx:
|
|
description: enables the receiving of data even while sending data.
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
|
|
rs485-term-gpios:
|
|
description: GPIO pin to enable RS485 bus termination.
|
|
maxItems: 1
|
|
|
|
rs485-rx-during-tx-gpios:
|
|
description: Output GPIO pin that sets the state of rs485-rx-during-tx. This
|
|
signal can be used to control the RX part of an RS485 transceiver. Thereby
|
|
the active state enables RX during TX.
|
|
maxItems: 1
|
|
|
|
additionalProperties: true
|
|
|
|
...
|