linux-stable/drivers/leds/leds-lm3692x.c
Uwe Kleine-König ed5c2f5fd1 i2c: Make remove callback return void
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-08-16 12:46:26 +02:00

529 lines
13 KiB
C

// SPDX-License-Identifier: GPL-2.0
// TI LM3692x LED chip family driver
// Copyright (C) 2017-18 Texas Instruments Incorporated - https://www.ti.com/
#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/leds.h>
#include <linux/log2.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#define LM36922_MODEL 0
#define LM36923_MODEL 1
#define LM3692X_REV 0x0
#define LM3692X_RESET 0x1
#define LM3692X_EN 0x10
#define LM3692X_BRT_CTRL 0x11
#define LM3692X_PWM_CTRL 0x12
#define LM3692X_BOOST_CTRL 0x13
#define LM3692X_AUTO_FREQ_HI 0x15
#define LM3692X_AUTO_FREQ_LO 0x16
#define LM3692X_BL_ADJ_THRESH 0x17
#define LM3692X_BRT_LSB 0x18
#define LM3692X_BRT_MSB 0x19
#define LM3692X_FAULT_CTRL 0x1e
#define LM3692X_FAULT_FLAGS 0x1f
#define LM3692X_SW_RESET BIT(0)
#define LM3692X_DEVICE_EN BIT(0)
#define LM3692X_LED1_EN BIT(1)
#define LM3692X_LED2_EN BIT(2)
#define LM36923_LED3_EN BIT(3)
#define LM3692X_ENABLE_MASK (LM3692X_DEVICE_EN | LM3692X_LED1_EN | \
LM3692X_LED2_EN | LM36923_LED3_EN)
/* Brightness Control Bits */
#define LM3692X_BL_ADJ_POL BIT(0)
#define LM3692X_RAMP_RATE_125us 0x00
#define LM3692X_RAMP_RATE_250us BIT(1)
#define LM3692X_RAMP_RATE_500us BIT(2)
#define LM3692X_RAMP_RATE_1ms (BIT(1) | BIT(2))
#define LM3692X_RAMP_RATE_2ms BIT(3)
#define LM3692X_RAMP_RATE_4ms (BIT(3) | BIT(1))
#define LM3692X_RAMP_RATE_8ms (BIT(2) | BIT(3))
#define LM3692X_RAMP_RATE_16ms (BIT(1) | BIT(2) | BIT(3))
#define LM3692X_RAMP_EN BIT(4)
#define LM3692X_BRHT_MODE_REG 0x00
#define LM3692X_BRHT_MODE_PWM BIT(5)
#define LM3692X_BRHT_MODE_MULTI_RAMP BIT(6)
#define LM3692X_BRHT_MODE_RAMP_MULTI (BIT(5) | BIT(6))
#define LM3692X_MAP_MODE_EXP BIT(7)
/* PWM Register Bits */
#define LM3692X_PWM_FILTER_100 BIT(0)
#define LM3692X_PWM_FILTER_150 BIT(1)
#define LM3692X_PWM_FILTER_200 (BIT(0) | BIT(1))
#define LM3692X_PWM_HYSTER_1LSB BIT(2)
#define LM3692X_PWM_HYSTER_2LSB BIT(3)
#define LM3692X_PWM_HYSTER_3LSB (BIT(3) | BIT(2))
#define LM3692X_PWM_HYSTER_4LSB BIT(4)
#define LM3692X_PWM_HYSTER_5LSB (BIT(4) | BIT(2))
#define LM3692X_PWM_HYSTER_6LSB (BIT(4) | BIT(3))
#define LM3692X_PWM_POLARITY BIT(5)
#define LM3692X_PWM_SAMP_4MHZ BIT(6)
#define LM3692X_PWM_SAMP_24MHZ BIT(7)
/* Boost Control Bits */
#define LM3692X_OCP_PROT_1A BIT(0)
#define LM3692X_OCP_PROT_1_25A BIT(1)
#define LM3692X_OCP_PROT_1_5A (BIT(0) | BIT(1))
#define LM3692X_OVP_21V BIT(2)
#define LM3692X_OVP_25V BIT(3)
#define LM3692X_OVP_29V (BIT(2) | BIT(3))
#define LM3692X_MIN_IND_22UH BIT(4)
#define LM3692X_BOOST_SW_1MHZ BIT(5)
#define LM3692X_BOOST_SW_NO_SHIFT BIT(6)
/* Fault Control Bits */
#define LM3692X_FAULT_CTRL_OVP BIT(0)
#define LM3692X_FAULT_CTRL_OCP BIT(1)
#define LM3692X_FAULT_CTRL_TSD BIT(2)
#define LM3692X_FAULT_CTRL_OPEN BIT(3)
/* Fault Flag Bits */
#define LM3692X_FAULT_FLAG_OVP BIT(0)
#define LM3692X_FAULT_FLAG_OCP BIT(1)
#define LM3692X_FAULT_FLAG_TSD BIT(2)
#define LM3692X_FAULT_FLAG_SHRT BIT(3)
#define LM3692X_FAULT_FLAG_OPEN BIT(4)
/**
* struct lm3692x_led
* @lock: Lock for reading/writing the device
* @client: Pointer to the I2C client
* @led_dev: LED class device pointer
* @regmap: Devices register map
* @enable_gpio: VDDIO/EN gpio to enable communication interface
* @regulator: LED supply regulator pointer
* @led_enable: LED sync to be enabled
* @model_id: Current device model ID enumerated
*/
struct lm3692x_led {
struct mutex lock;
struct i2c_client *client;
struct led_classdev led_dev;
struct regmap *regmap;
struct gpio_desc *enable_gpio;
struct regulator *regulator;
int led_enable;
int model_id;
u8 boost_ctrl, brightness_ctrl;
bool enabled;
};
static const struct reg_default lm3692x_reg_defs[] = {
{LM3692X_EN, 0xf},
{LM3692X_BRT_CTRL, 0x61},
{LM3692X_PWM_CTRL, 0x73},
{LM3692X_BOOST_CTRL, 0x6f},
{LM3692X_AUTO_FREQ_HI, 0x0},
{LM3692X_AUTO_FREQ_LO, 0x0},
{LM3692X_BL_ADJ_THRESH, 0x0},
{LM3692X_BRT_LSB, 0x7},
{LM3692X_BRT_MSB, 0xff},
{LM3692X_FAULT_CTRL, 0x7},
};
static const struct regmap_config lm3692x_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.max_register = LM3692X_FAULT_FLAGS,
.reg_defaults = lm3692x_reg_defs,
.num_reg_defaults = ARRAY_SIZE(lm3692x_reg_defs),
.cache_type = REGCACHE_RBTREE,
};
static int lm3692x_fault_check(struct lm3692x_led *led)
{
int ret;
unsigned int read_buf;
ret = regmap_read(led->regmap, LM3692X_FAULT_FLAGS, &read_buf);
if (ret)
return ret;
if (read_buf)
dev_err(&led->client->dev, "Detected a fault 0x%X\n", read_buf);
/* The first read may clear the fault. Check again to see if the fault
* still exits and return that value.
*/
regmap_read(led->regmap, LM3692X_FAULT_FLAGS, &read_buf);
if (read_buf)
dev_err(&led->client->dev, "Second read of fault flags 0x%X\n",
read_buf);
return read_buf;
}
static int lm3692x_leds_enable(struct lm3692x_led *led)
{
int enable_state;
int ret, reg_ret;
if (led->enabled)
return 0;
if (led->regulator) {
ret = regulator_enable(led->regulator);
if (ret) {
dev_err(&led->client->dev,
"Failed to enable regulator: %d\n", ret);
return ret;
}
}
if (led->enable_gpio)
gpiod_direction_output(led->enable_gpio, 1);
ret = lm3692x_fault_check(led);
if (ret) {
dev_err(&led->client->dev, "Cannot read/clear faults: %d\n",
ret);
goto out;
}
ret = regmap_write(led->regmap, LM3692X_BRT_CTRL, 0x00);
if (ret)
goto out;
/*
* For glitch free operation, the following data should
* only be written while LEDx enable bits are 0 and the device enable
* bit is set to 1.
* per Section 7.5.14 of the data sheet
*/
ret = regmap_write(led->regmap, LM3692X_EN, LM3692X_DEVICE_EN);
if (ret)
goto out;
/* Set the brightness to 0 so when enabled the LEDs do not come
* on with full brightness.
*/
ret = regmap_write(led->regmap, LM3692X_BRT_MSB, 0);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_BRT_LSB, 0);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_PWM_CTRL,
LM3692X_PWM_FILTER_100 | LM3692X_PWM_SAMP_24MHZ);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_BOOST_CTRL, led->boost_ctrl);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_AUTO_FREQ_HI, 0x00);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_AUTO_FREQ_LO, 0x00);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_BL_ADJ_THRESH, 0x00);
if (ret)
goto out;
ret = regmap_write(led->regmap, LM3692X_BRT_CTRL,
LM3692X_BL_ADJ_POL | LM3692X_RAMP_EN);
if (ret)
goto out;
switch (led->led_enable) {
case 0:
default:
if (led->model_id == LM36923_MODEL)
enable_state = LM3692X_LED1_EN | LM3692X_LED2_EN |
LM36923_LED3_EN;
else
enable_state = LM3692X_LED1_EN | LM3692X_LED2_EN;
break;
case 1:
enable_state = LM3692X_LED1_EN;
break;
case 2:
enable_state = LM3692X_LED2_EN;
break;
case 3:
if (led->model_id == LM36923_MODEL) {
enable_state = LM36923_LED3_EN;
break;
}
ret = -EINVAL;
dev_err(&led->client->dev,
"LED3 sync not available on this device\n");
goto out;
}
ret = regmap_update_bits(led->regmap, LM3692X_EN, LM3692X_ENABLE_MASK,
enable_state | LM3692X_DEVICE_EN);
led->enabled = true;
return ret;
out:
dev_err(&led->client->dev, "Fail writing initialization values\n");
if (led->enable_gpio)
gpiod_direction_output(led->enable_gpio, 0);
if (led->regulator) {
reg_ret = regulator_disable(led->regulator);
if (reg_ret)
dev_err(&led->client->dev,
"Failed to disable regulator: %d\n", reg_ret);
}
return ret;
}
static int lm3692x_leds_disable(struct lm3692x_led *led)
{
int ret;
if (!led->enabled)
return 0;
ret = regmap_update_bits(led->regmap, LM3692X_EN, LM3692X_DEVICE_EN, 0);
if (ret) {
dev_err(&led->client->dev, "Failed to disable regulator: %d\n",
ret);
return ret;
}
if (led->enable_gpio)
gpiod_direction_output(led->enable_gpio, 0);
if (led->regulator) {
ret = regulator_disable(led->regulator);
if (ret)
dev_err(&led->client->dev,
"Failed to disable regulator: %d\n", ret);
}
led->enabled = false;
return ret;
}
static int lm3692x_brightness_set(struct led_classdev *led_cdev,
enum led_brightness brt_val)
{
struct lm3692x_led *led =
container_of(led_cdev, struct lm3692x_led, led_dev);
int ret;
int led_brightness_lsb = (brt_val >> 5);
mutex_lock(&led->lock);
if (brt_val == 0) {
ret = lm3692x_leds_disable(led);
goto out;
} else {
lm3692x_leds_enable(led);
}
ret = lm3692x_fault_check(led);
if (ret) {
dev_err(&led->client->dev, "Cannot read/clear faults: %d\n",
ret);
goto out;
}
ret = regmap_write(led->regmap, LM3692X_BRT_MSB, brt_val);
if (ret) {
dev_err(&led->client->dev, "Cannot write MSB: %d\n", ret);
goto out;
}
ret = regmap_write(led->regmap, LM3692X_BRT_LSB, led_brightness_lsb);
if (ret) {
dev_err(&led->client->dev, "Cannot write LSB: %d\n", ret);
goto out;
}
out:
mutex_unlock(&led->lock);
return ret;
}
static enum led_brightness lm3692x_max_brightness(struct lm3692x_led *led,
u32 max_cur)
{
u32 max_code;
/* see p.12 of LM36922 data sheet for brightness formula */
max_code = ((max_cur * 1000) - 37806) / 12195;
if (max_code > 0x7FF)
max_code = 0x7FF;
return max_code >> 3;
}
static int lm3692x_probe_dt(struct lm3692x_led *led)
{
struct fwnode_handle *child = NULL;
struct led_init_data init_data = {};
u32 ovp, max_cur;
int ret;
led->enable_gpio = devm_gpiod_get_optional(&led->client->dev,
"enable", GPIOD_OUT_LOW);
if (IS_ERR(led->enable_gpio)) {
ret = PTR_ERR(led->enable_gpio);
dev_err(&led->client->dev, "Failed to get enable gpio: %d\n",
ret);
return ret;
}
led->regulator = devm_regulator_get_optional(&led->client->dev, "vled");
if (IS_ERR(led->regulator)) {
ret = PTR_ERR(led->regulator);
if (ret != -ENODEV)
return dev_err_probe(&led->client->dev, ret,
"Failed to get vled regulator\n");
led->regulator = NULL;
}
led->boost_ctrl = LM3692X_BOOST_SW_1MHZ |
LM3692X_BOOST_SW_NO_SHIFT |
LM3692X_OCP_PROT_1_5A;
ret = device_property_read_u32(&led->client->dev,
"ti,ovp-microvolt", &ovp);
if (ret) {
led->boost_ctrl |= LM3692X_OVP_29V;
} else {
switch (ovp) {
case 17000000:
break;
case 21000000:
led->boost_ctrl |= LM3692X_OVP_21V;
break;
case 25000000:
led->boost_ctrl |= LM3692X_OVP_25V;
break;
case 29000000:
led->boost_ctrl |= LM3692X_OVP_29V;
break;
default:
dev_err(&led->client->dev, "Invalid OVP %d\n", ovp);
return -EINVAL;
}
}
child = device_get_next_child_node(&led->client->dev, child);
if (!child) {
dev_err(&led->client->dev, "No LED Child node\n");
return -ENODEV;
}
ret = fwnode_property_read_u32(child, "reg", &led->led_enable);
if (ret) {
fwnode_handle_put(child);
dev_err(&led->client->dev, "reg DT property missing\n");
return ret;
}
ret = fwnode_property_read_u32(child, "led-max-microamp", &max_cur);
led->led_dev.max_brightness = ret ? LED_FULL :
lm3692x_max_brightness(led, max_cur);
init_data.fwnode = child;
init_data.devicename = led->client->name;
init_data.default_label = ":";
ret = devm_led_classdev_register_ext(&led->client->dev, &led->led_dev,
&init_data);
if (ret)
dev_err(&led->client->dev, "led register err: %d\n", ret);
fwnode_handle_put(init_data.fwnode);
return ret;
}
static int lm3692x_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct lm3692x_led *led;
int ret;
led = devm_kzalloc(&client->dev, sizeof(*led), GFP_KERNEL);
if (!led)
return -ENOMEM;
mutex_init(&led->lock);
led->client = client;
led->led_dev.brightness_set_blocking = lm3692x_brightness_set;
led->model_id = id->driver_data;
i2c_set_clientdata(client, led);
led->regmap = devm_regmap_init_i2c(client, &lm3692x_regmap_config);
if (IS_ERR(led->regmap)) {
ret = PTR_ERR(led->regmap);
dev_err(&client->dev, "Failed to allocate register map: %d\n",
ret);
return ret;
}
ret = lm3692x_probe_dt(led);
if (ret)
return ret;
ret = lm3692x_leds_enable(led);
if (ret)
return ret;
return 0;
}
static void lm3692x_remove(struct i2c_client *client)
{
struct lm3692x_led *led = i2c_get_clientdata(client);
lm3692x_leds_disable(led);
mutex_destroy(&led->lock);
}
static const struct i2c_device_id lm3692x_id[] = {
{ "lm36922", LM36922_MODEL },
{ "lm36923", LM36923_MODEL },
{ }
};
MODULE_DEVICE_TABLE(i2c, lm3692x_id);
static const struct of_device_id of_lm3692x_leds_match[] = {
{ .compatible = "ti,lm36922", },
{ .compatible = "ti,lm36923", },
{},
};
MODULE_DEVICE_TABLE(of, of_lm3692x_leds_match);
static struct i2c_driver lm3692x_driver = {
.driver = {
.name = "lm3692x",
.of_match_table = of_lm3692x_leds_match,
},
.probe = lm3692x_probe,
.remove = lm3692x_remove,
.id_table = lm3692x_id,
};
module_i2c_driver(lm3692x_driver);
MODULE_DESCRIPTION("Texas Instruments LM3692X LED driver");
MODULE_AUTHOR("Dan Murphy <dmurphy@ti.com>");
MODULE_LICENSE("GPL v2");