mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-08-23 01:10:04 +00:00
![Tejun Heo](/assets/img/avatar_default.png)
Currently, port configuration reporting has the following problems. * iomapped address is reported instead of raw address * report contains irrelevant fields or lacks necessary fields for non-SFF controllers. * host->irq/irq2 are there just for reporting and hacky. This patch implements and uses ata_port_desc() and ata_port_pbar_desc(). ata_port_desc() is almost identical to ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no locking requirement, can only be used during host initialization and " " is used as separator instead of ", ". ata_port_pbar_desc() is a helper to ease reporting of a PCI BAR or an offsetted address into it. LLD pushes whatever description it wants using the above two functions. The accumulated description is printed on host registration after "[S/P]ATA max MAX_XFERMODE ". SFF init helpers and ata_host_activate() automatically add descriptions for addresses and irq respectively, so only LLDs which isn't standard SFF need to add custom descriptions. In many cases, such controllers need to report different things anyway. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
302 lines
7.6 KiB
C
302 lines
7.6 KiB
C
/*
|
|
* pata_hpt3x3 - HPT3x3 driver
|
|
* (c) Copyright 2005-2006 Red Hat
|
|
*
|
|
* Was pata_hpt34x but the naming was confusing as it supported the
|
|
* 343 and 363 so it has been renamed.
|
|
*
|
|
* Based on:
|
|
* linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002
|
|
* Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
|
|
*
|
|
* May be copied or modified under the terms of the GNU General Public
|
|
* License
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/init.h>
|
|
#include <linux/blkdev.h>
|
|
#include <linux/delay.h>
|
|
#include <scsi/scsi_host.h>
|
|
#include <linux/libata.h>
|
|
|
|
#define DRV_NAME "pata_hpt3x3"
|
|
#define DRV_VERSION "0.5.3"
|
|
|
|
/**
|
|
* hpt3x3_set_piomode - PIO setup
|
|
* @ap: ATA interface
|
|
* @adev: device on the interface
|
|
*
|
|
* Set our PIO requirements. This is fairly simple on the HPT3x3 as
|
|
* all we have to do is clear the MWDMA and UDMA bits then load the
|
|
* mode number.
|
|
*/
|
|
|
|
static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u32 r1, r2;
|
|
int dn = 2 * ap->port_no + adev->devno;
|
|
|
|
pci_read_config_dword(pdev, 0x44, &r1);
|
|
pci_read_config_dword(pdev, 0x48, &r2);
|
|
/* Load the PIO timing number */
|
|
r1 &= ~(7 << (3 * dn));
|
|
r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn);
|
|
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
|
|
|
|
pci_write_config_dword(pdev, 0x44, r1);
|
|
pci_write_config_dword(pdev, 0x48, r2);
|
|
}
|
|
|
|
#if defined(CONFIG_PATA_HPT3X3_DMA)
|
|
/**
|
|
* hpt3x3_set_dmamode - DMA timing setup
|
|
* @ap: ATA interface
|
|
* @adev: Device being configured
|
|
*
|
|
* Set up the channel for MWDMA or UDMA modes. Much the same as with
|
|
* PIO, load the mode number and then set MWDMA or UDMA flag.
|
|
*
|
|
* 0x44 : bit 0-2 master mode, 3-5 slave mode, etc
|
|
* 0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
|
|
*/
|
|
|
|
static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
|
|
u32 r1, r2;
|
|
int dn = 2 * ap->port_no + adev->devno;
|
|
int mode_num = adev->dma_mode & 0x0F;
|
|
|
|
pci_read_config_dword(pdev, 0x44, &r1);
|
|
pci_read_config_dword(pdev, 0x48, &r2);
|
|
/* Load the timing number */
|
|
r1 &= ~(7 << (3 * dn));
|
|
r1 |= (mode_num << (3 * dn));
|
|
r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */
|
|
|
|
if (adev->dma_mode >= XFER_UDMA_0)
|
|
r2 |= (0x10 << dn); /* Ultra mode */
|
|
else
|
|
r2 |= (0x01 << dn); /* MWDMA */
|
|
|
|
pci_write_config_dword(pdev, 0x44, r1);
|
|
pci_write_config_dword(pdev, 0x48, r2);
|
|
}
|
|
#endif /* CONFIG_PATA_HPT3X3_DMA */
|
|
|
|
/**
|
|
* hpt3x3_atapi_dma - ATAPI DMA check
|
|
* @qc: Queued command
|
|
*
|
|
* Just say no - we don't do ATAPI DMA
|
|
*/
|
|
|
|
static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
static struct scsi_host_template hpt3x3_sht = {
|
|
.module = THIS_MODULE,
|
|
.name = DRV_NAME,
|
|
.ioctl = ata_scsi_ioctl,
|
|
.queuecommand = ata_scsi_queuecmd,
|
|
.can_queue = ATA_DEF_QUEUE,
|
|
.this_id = ATA_SHT_THIS_ID,
|
|
.sg_tablesize = LIBATA_MAX_PRD,
|
|
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
|
|
.emulated = ATA_SHT_EMULATED,
|
|
.use_clustering = ATA_SHT_USE_CLUSTERING,
|
|
.proc_name = DRV_NAME,
|
|
.dma_boundary = ATA_DMA_BOUNDARY,
|
|
.slave_configure = ata_scsi_slave_config,
|
|
.slave_destroy = ata_scsi_slave_destroy,
|
|
.bios_param = ata_std_bios_param,
|
|
};
|
|
|
|
static struct ata_port_operations hpt3x3_port_ops = {
|
|
.set_piomode = hpt3x3_set_piomode,
|
|
#if defined(CONFIG_PATA_HPT3X3_DMA)
|
|
.set_dmamode = hpt3x3_set_dmamode,
|
|
#endif
|
|
.mode_filter = ata_pci_default_filter,
|
|
|
|
.tf_load = ata_tf_load,
|
|
.tf_read = ata_tf_read,
|
|
.check_status = ata_check_status,
|
|
.exec_command = ata_exec_command,
|
|
.dev_select = ata_std_dev_select,
|
|
|
|
.freeze = ata_bmdma_freeze,
|
|
.thaw = ata_bmdma_thaw,
|
|
.error_handler = ata_bmdma_error_handler,
|
|
.post_internal_cmd = ata_bmdma_post_internal_cmd,
|
|
.cable_detect = ata_cable_40wire,
|
|
|
|
.bmdma_setup = ata_bmdma_setup,
|
|
.bmdma_start = ata_bmdma_start,
|
|
.bmdma_stop = ata_bmdma_stop,
|
|
.bmdma_status = ata_bmdma_status,
|
|
.check_atapi_dma= hpt3x3_atapi_dma,
|
|
|
|
.qc_prep = ata_qc_prep,
|
|
.qc_issue = ata_qc_issue_prot,
|
|
|
|
.data_xfer = ata_data_xfer,
|
|
|
|
.irq_handler = ata_interrupt,
|
|
.irq_clear = ata_bmdma_irq_clear,
|
|
.irq_on = ata_irq_on,
|
|
|
|
.port_start = ata_sff_port_start,
|
|
};
|
|
|
|
/**
|
|
* hpt3x3_init_chipset - chip setup
|
|
* @dev: PCI device
|
|
*
|
|
* Perform the setup required at boot and on resume.
|
|
*/
|
|
|
|
static void hpt3x3_init_chipset(struct pci_dev *dev)
|
|
{
|
|
u16 cmd;
|
|
/* Initialize the board */
|
|
pci_write_config_word(dev, 0x80, 0x00);
|
|
/* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
|
|
pci_read_config_word(dev, PCI_COMMAND, &cmd);
|
|
if (cmd & PCI_COMMAND_MEMORY)
|
|
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
|
|
else
|
|
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
|
|
}
|
|
|
|
/**
|
|
* hpt3x3_init_one - Initialise an HPT343/363
|
|
* @pdev: PCI device
|
|
* @id: Entry in match table
|
|
*
|
|
* Perform basic initialisation. We set the device up so we access all
|
|
* ports via BAR4. This is neccessary to work around errata.
|
|
*/
|
|
|
|
static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
|
|
{
|
|
static int printed_version;
|
|
static const struct ata_port_info info = {
|
|
.sht = &hpt3x3_sht,
|
|
.flags = ATA_FLAG_SLAVE_POSS,
|
|
.pio_mask = 0x1f,
|
|
#if defined(CONFIG_PATA_HPT3X3_DMA)
|
|
/* Further debug needed */
|
|
.mwdma_mask = 0x07,
|
|
.udma_mask = 0x07,
|
|
#endif
|
|
.port_ops = &hpt3x3_port_ops
|
|
};
|
|
/* Register offsets of taskfiles in BAR4 area */
|
|
static const u8 offset_cmd[2] = { 0x20, 0x28 };
|
|
static const u8 offset_ctl[2] = { 0x36, 0x3E };
|
|
const struct ata_port_info *ppi[] = { &info, NULL };
|
|
struct ata_host *host;
|
|
int i, rc;
|
|
void __iomem *base;
|
|
|
|
hpt3x3_init_chipset(pdev);
|
|
|
|
if (!printed_version++)
|
|
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
|
|
|
|
host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
|
|
if (!host)
|
|
return -ENOMEM;
|
|
/* acquire resources and fill host */
|
|
rc = pcim_enable_device(pdev);
|
|
if (rc)
|
|
return rc;
|
|
|
|
/* Everything is relative to BAR4 if we set up this way */
|
|
rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
|
|
if (rc == -EBUSY)
|
|
pcim_pin_device(pdev);
|
|
if (rc)
|
|
return rc;
|
|
host->iomap = pcim_iomap_table(pdev);
|
|
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
|
|
if (rc)
|
|
return rc;
|
|
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
|
|
if (rc)
|
|
return rc;
|
|
|
|
base = host->iomap[4]; /* Bus mastering base */
|
|
|
|
for (i = 0; i < host->n_ports; i++) {
|
|
struct ata_port *ap = host->ports[i];
|
|
struct ata_ioports *ioaddr = &ap->ioaddr;
|
|
|
|
ioaddr->cmd_addr = base + offset_cmd[i];
|
|
ioaddr->altstatus_addr =
|
|
ioaddr->ctl_addr = base + offset_ctl[i];
|
|
ioaddr->scr_addr = NULL;
|
|
ata_std_ports(ioaddr);
|
|
ioaddr->bmdma_addr = base + 8 * i;
|
|
|
|
ata_port_pbar_desc(ap, 4, -1, "ioport");
|
|
ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd");
|
|
}
|
|
pci_set_master(pdev);
|
|
return ata_host_activate(host, pdev->irq, ata_interrupt, IRQF_SHARED,
|
|
&hpt3x3_sht);
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static int hpt3x3_reinit_one(struct pci_dev *dev)
|
|
{
|
|
hpt3x3_init_chipset(dev);
|
|
return ata_pci_device_resume(dev);
|
|
}
|
|
#endif
|
|
|
|
static const struct pci_device_id hpt3x3[] = {
|
|
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
|
|
|
|
{ },
|
|
};
|
|
|
|
static struct pci_driver hpt3x3_pci_driver = {
|
|
.name = DRV_NAME,
|
|
.id_table = hpt3x3,
|
|
.probe = hpt3x3_init_one,
|
|
.remove = ata_pci_remove_one,
|
|
#ifdef CONFIG_PM
|
|
.suspend = ata_pci_device_suspend,
|
|
.resume = hpt3x3_reinit_one,
|
|
#endif
|
|
};
|
|
|
|
static int __init hpt3x3_init(void)
|
|
{
|
|
return pci_register_driver(&hpt3x3_pci_driver);
|
|
}
|
|
|
|
|
|
static void __exit hpt3x3_exit(void)
|
|
{
|
|
pci_unregister_driver(&hpt3x3_pci_driver);
|
|
}
|
|
|
|
|
|
MODULE_AUTHOR("Alan Cox");
|
|
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DEVICE_TABLE(pci, hpt3x3);
|
|
MODULE_VERSION(DRV_VERSION);
|
|
|
|
module_init(hpt3x3_init);
|
|
module_exit(hpt3x3_exit);
|