linux-stable/drivers/i2c/busses/i2c-uniphier.c
Wolfram Sang ea1558ce14 i2c: move drivers from strlcpy to strscpy
Follow the advice of the below link and prefer 'strscpy'. Conversion is
easy because no driver used the return value and has been done with a
simple sed invocation.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-08-11 23:02:51 +02:00

439 lines
11 KiB
C

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
*/
#include <linux/clk.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#define UNIPHIER_I2C_DTRM 0x00 /* TX register */
#define UNIPHIER_I2C_DTRM_IRQEN BIT(11) /* enable interrupt */
#define UNIPHIER_I2C_DTRM_STA BIT(10) /* start condition */
#define UNIPHIER_I2C_DTRM_STO BIT(9) /* stop condition */
#define UNIPHIER_I2C_DTRM_NACK BIT(8) /* do not return ACK */
#define UNIPHIER_I2C_DTRM_RD BIT(0) /* read transaction */
#define UNIPHIER_I2C_DREC 0x04 /* RX register */
#define UNIPHIER_I2C_DREC_MST BIT(14) /* 1 = master, 0 = slave */
#define UNIPHIER_I2C_DREC_TX BIT(13) /* 1 = transmit, 0 = receive */
#define UNIPHIER_I2C_DREC_STS BIT(12) /* stop condition detected */
#define UNIPHIER_I2C_DREC_LRB BIT(11) /* no ACK */
#define UNIPHIER_I2C_DREC_LAB BIT(9) /* arbitration lost */
#define UNIPHIER_I2C_DREC_BBN BIT(8) /* bus not busy */
#define UNIPHIER_I2C_MYAD 0x08 /* slave address */
#define UNIPHIER_I2C_CLK 0x0c /* clock frequency control */
#define UNIPHIER_I2C_BRST 0x10 /* bus reset */
#define UNIPHIER_I2C_BRST_FOEN BIT(1) /* normal operation */
#define UNIPHIER_I2C_BRST_RSCL BIT(0) /* release SCL */
#define UNIPHIER_I2C_HOLD 0x14 /* hold time control */
#define UNIPHIER_I2C_BSTS 0x18 /* bus status monitor */
#define UNIPHIER_I2C_BSTS_SDA BIT(1) /* readback of SDA line */
#define UNIPHIER_I2C_BSTS_SCL BIT(0) /* readback of SCL line */
#define UNIPHIER_I2C_NOISE 0x1c /* noise filter control */
#define UNIPHIER_I2C_SETUP 0x20 /* setup time control */
struct uniphier_i2c_priv {
struct completion comp;
struct i2c_adapter adap;
void __iomem *membase;
struct clk *clk;
unsigned int busy_cnt;
unsigned int clk_cycle;
};
static irqreturn_t uniphier_i2c_interrupt(int irq, void *dev_id)
{
struct uniphier_i2c_priv *priv = dev_id;
/*
* This hardware uses edge triggered interrupt. Do not touch the
* hardware registers in this handler to make sure to catch the next
* interrupt edge. Just send a complete signal and return.
*/
complete(&priv->comp);
return IRQ_HANDLED;
}
static int uniphier_i2c_xfer_byte(struct i2c_adapter *adap, u32 txdata,
u32 *rxdatap)
{
struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
unsigned long time_left;
u32 rxdata;
reinit_completion(&priv->comp);
txdata |= UNIPHIER_I2C_DTRM_IRQEN;
writel(txdata, priv->membase + UNIPHIER_I2C_DTRM);
time_left = wait_for_completion_timeout(&priv->comp, adap->timeout);
if (unlikely(!time_left)) {
dev_err(&adap->dev, "transaction timeout\n");
return -ETIMEDOUT;
}
rxdata = readl(priv->membase + UNIPHIER_I2C_DREC);
if (rxdatap)
*rxdatap = rxdata;
return 0;
}
static int uniphier_i2c_send_byte(struct i2c_adapter *adap, u32 txdata)
{
u32 rxdata;
int ret;
ret = uniphier_i2c_xfer_byte(adap, txdata, &rxdata);
if (ret)
return ret;
if (unlikely(rxdata & UNIPHIER_I2C_DREC_LAB))
return -EAGAIN;
if (unlikely(rxdata & UNIPHIER_I2C_DREC_LRB))
return -ENXIO;
return 0;
}
static int uniphier_i2c_tx(struct i2c_adapter *adap, u16 addr, u16 len,
const u8 *buf)
{
int ret;
ret = uniphier_i2c_send_byte(adap, addr << 1 |
UNIPHIER_I2C_DTRM_STA |
UNIPHIER_I2C_DTRM_NACK);
if (ret)
return ret;
while (len--) {
ret = uniphier_i2c_send_byte(adap,
UNIPHIER_I2C_DTRM_NACK | *buf++);
if (ret)
return ret;
}
return 0;
}
static int uniphier_i2c_rx(struct i2c_adapter *adap, u16 addr, u16 len,
u8 *buf)
{
int ret;
ret = uniphier_i2c_send_byte(adap, addr << 1 |
UNIPHIER_I2C_DTRM_STA |
UNIPHIER_I2C_DTRM_NACK |
UNIPHIER_I2C_DTRM_RD);
if (ret)
return ret;
while (len--) {
u32 rxdata;
ret = uniphier_i2c_xfer_byte(adap,
len ? 0 : UNIPHIER_I2C_DTRM_NACK,
&rxdata);
if (ret)
return ret;
*buf++ = rxdata;
}
return 0;
}
static int uniphier_i2c_stop(struct i2c_adapter *adap)
{
return uniphier_i2c_send_byte(adap, UNIPHIER_I2C_DTRM_STO |
UNIPHIER_I2C_DTRM_NACK);
}
static int uniphier_i2c_master_xfer_one(struct i2c_adapter *adap,
struct i2c_msg *msg, bool stop)
{
bool is_read = msg->flags & I2C_M_RD;
bool recovery = false;
int ret;
if (is_read)
ret = uniphier_i2c_rx(adap, msg->addr, msg->len, msg->buf);
else
ret = uniphier_i2c_tx(adap, msg->addr, msg->len, msg->buf);
if (ret == -EAGAIN) /* could not acquire bus. bail out without STOP */
return ret;
if (ret == -ETIMEDOUT) {
/* This error is fatal. Needs recovery. */
stop = false;
recovery = true;
}
if (stop) {
int ret2 = uniphier_i2c_stop(adap);
if (ret2) {
/* Failed to issue STOP. The bus needs recovery. */
recovery = true;
ret = ret ?: ret2;
}
}
if (recovery)
i2c_recover_bus(adap);
return ret;
}
static int uniphier_i2c_check_bus_busy(struct i2c_adapter *adap)
{
struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
if (!(readl(priv->membase + UNIPHIER_I2C_DREC) &
UNIPHIER_I2C_DREC_BBN)) {
if (priv->busy_cnt++ > 3) {
/*
* If bus busy continues too long, it is probably
* in a wrong state. Try bus recovery.
*/
i2c_recover_bus(adap);
priv->busy_cnt = 0;
}
return -EAGAIN;
}
priv->busy_cnt = 0;
return 0;
}
static int uniphier_i2c_master_xfer(struct i2c_adapter *adap,
struct i2c_msg *msgs, int num)
{
struct i2c_msg *msg, *emsg = msgs + num;
int ret;
ret = uniphier_i2c_check_bus_busy(adap);
if (ret)
return ret;
for (msg = msgs; msg < emsg; msg++) {
/* Emit STOP if it is the last message or I2C_M_STOP is set. */
bool stop = (msg + 1 == emsg) || (msg->flags & I2C_M_STOP);
ret = uniphier_i2c_master_xfer_one(adap, msg, stop);
if (ret)
return ret;
}
return num;
}
static u32 uniphier_i2c_functionality(struct i2c_adapter *adap)
{
return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
}
static const struct i2c_algorithm uniphier_i2c_algo = {
.master_xfer = uniphier_i2c_master_xfer,
.functionality = uniphier_i2c_functionality,
};
static void uniphier_i2c_reset(struct uniphier_i2c_priv *priv, bool reset_on)
{
u32 val = UNIPHIER_I2C_BRST_RSCL;
val |= reset_on ? 0 : UNIPHIER_I2C_BRST_FOEN;
writel(val, priv->membase + UNIPHIER_I2C_BRST);
}
static int uniphier_i2c_get_scl(struct i2c_adapter *adap)
{
struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
UNIPHIER_I2C_BSTS_SCL);
}
static void uniphier_i2c_set_scl(struct i2c_adapter *adap, int val)
{
struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
writel(val ? UNIPHIER_I2C_BRST_RSCL : 0,
priv->membase + UNIPHIER_I2C_BRST);
}
static int uniphier_i2c_get_sda(struct i2c_adapter *adap)
{
struct uniphier_i2c_priv *priv = i2c_get_adapdata(adap);
return !!(readl(priv->membase + UNIPHIER_I2C_BSTS) &
UNIPHIER_I2C_BSTS_SDA);
}
static void uniphier_i2c_unprepare_recovery(struct i2c_adapter *adap)
{
uniphier_i2c_reset(i2c_get_adapdata(adap), false);
}
static struct i2c_bus_recovery_info uniphier_i2c_bus_recovery_info = {
.recover_bus = i2c_generic_scl_recovery,
.get_scl = uniphier_i2c_get_scl,
.set_scl = uniphier_i2c_set_scl,
.get_sda = uniphier_i2c_get_sda,
.unprepare_recovery = uniphier_i2c_unprepare_recovery,
};
static void uniphier_i2c_hw_init(struct uniphier_i2c_priv *priv)
{
unsigned int cyc = priv->clk_cycle;
uniphier_i2c_reset(priv, true);
/*
* Bit30-16: clock cycles of tLOW.
* Standard-mode: tLOW = 4.7 us, tHIGH = 4.0 us
* Fast-mode: tLOW = 1.3 us, tHIGH = 0.6 us
* "tLow/tHIGH = 5/4" meets both.
*/
writel((cyc * 5 / 9 << 16) | cyc, priv->membase + UNIPHIER_I2C_CLK);
uniphier_i2c_reset(priv, false);
}
static int uniphier_i2c_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct uniphier_i2c_priv *priv;
u32 bus_speed;
unsigned long clk_rate;
int irq, ret;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->membase = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(priv->membase))
return PTR_ERR(priv->membase);
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
if (of_property_read_u32(dev->of_node, "clock-frequency", &bus_speed))
bus_speed = I2C_MAX_STANDARD_MODE_FREQ;
if (!bus_speed || bus_speed > I2C_MAX_FAST_MODE_FREQ) {
dev_err(dev, "invalid clock-frequency %d\n", bus_speed);
return -EINVAL;
}
priv->clk = devm_clk_get(dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(dev, "failed to get clock\n");
return PTR_ERR(priv->clk);
}
ret = clk_prepare_enable(priv->clk);
if (ret)
return ret;
clk_rate = clk_get_rate(priv->clk);
if (!clk_rate) {
dev_err(dev, "input clock rate should not be zero\n");
ret = -EINVAL;
goto disable_clk;
}
priv->clk_cycle = clk_rate / bus_speed;
init_completion(&priv->comp);
priv->adap.owner = THIS_MODULE;
priv->adap.algo = &uniphier_i2c_algo;
priv->adap.dev.parent = dev;
priv->adap.dev.of_node = dev->of_node;
strscpy(priv->adap.name, "UniPhier I2C", sizeof(priv->adap.name));
priv->adap.bus_recovery_info = &uniphier_i2c_bus_recovery_info;
i2c_set_adapdata(&priv->adap, priv);
platform_set_drvdata(pdev, priv);
uniphier_i2c_hw_init(priv);
ret = devm_request_irq(dev, irq, uniphier_i2c_interrupt, 0, pdev->name,
priv);
if (ret) {
dev_err(dev, "failed to request irq %d\n", irq);
goto disable_clk;
}
ret = i2c_add_adapter(&priv->adap);
disable_clk:
if (ret)
clk_disable_unprepare(priv->clk);
return ret;
}
static int uniphier_i2c_remove(struct platform_device *pdev)
{
struct uniphier_i2c_priv *priv = platform_get_drvdata(pdev);
i2c_del_adapter(&priv->adap);
clk_disable_unprepare(priv->clk);
return 0;
}
static int __maybe_unused uniphier_i2c_suspend(struct device *dev)
{
struct uniphier_i2c_priv *priv = dev_get_drvdata(dev);
clk_disable_unprepare(priv->clk);
return 0;
}
static int __maybe_unused uniphier_i2c_resume(struct device *dev)
{
struct uniphier_i2c_priv *priv = dev_get_drvdata(dev);
int ret;
ret = clk_prepare_enable(priv->clk);
if (ret)
return ret;
uniphier_i2c_hw_init(priv);
return 0;
}
static const struct dev_pm_ops uniphier_i2c_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(uniphier_i2c_suspend, uniphier_i2c_resume)
};
static const struct of_device_id uniphier_i2c_match[] = {
{ .compatible = "socionext,uniphier-i2c" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, uniphier_i2c_match);
static struct platform_driver uniphier_i2c_drv = {
.probe = uniphier_i2c_probe,
.remove = uniphier_i2c_remove,
.driver = {
.name = "uniphier-i2c",
.of_match_table = uniphier_i2c_match,
.pm = &uniphier_i2c_pm_ops,
},
};
module_platform_driver(uniphier_i2c_drv);
MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
MODULE_DESCRIPTION("UniPhier I2C bus driver");
MODULE_LICENSE("GPL");