linux-stable/arch/powerpc/platforms/powernv/pci.c
Gavin Shan 9bf41be673 powerpc/powernv: Use dev-node in PCI config accessors
Currently, we're using the combo (PCI bus + devfn) in the PCI
config accessors and PCI config accessors in EEH depends on them.
However, it's not safe to refer the PCI bus which might have been
removed during hotplug. So we're using device node in the PCI
config accessors and the corresponding backends just reuse them.

The patch also fix one potential risk: We possiblly have frozen
PE during the early PCI probe time, but we haven't setup the PE
mapping yet. So the errors should be counted to PE#0.

Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-07-01 11:10:33 +10:00

625 lines
17 KiB
C

/*
* Support PCI/PCIe on PowerNV platforms
*
* Currently supports only P5IOC2
*
* Copyright 2011 Benjamin Herrenschmidt, IBM Corp.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/bootmem.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/msi.h>
#include <linux/iommu.h>
#include <asm/sections.h>
#include <asm/io.h>
#include <asm/prom.h>
#include <asm/pci-bridge.h>
#include <asm/machdep.h>
#include <asm/msi_bitmap.h>
#include <asm/ppc-pci.h>
#include <asm/opal.h>
#include <asm/iommu.h>
#include <asm/tce.h>
#include <asm/firmware.h>
#include <asm/eeh_event.h>
#include <asm/eeh.h>
#include "powernv.h"
#include "pci.h"
/* Delay in usec */
#define PCI_RESET_DELAY_US 3000000
#define cfg_dbg(fmt...) do { } while(0)
//#define cfg_dbg(fmt...) printk(fmt)
#ifdef CONFIG_PCI_MSI
static int pnv_msi_check_device(struct pci_dev* pdev, int nvec, int type)
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
struct pci_dn *pdn = pci_get_pdn(pdev);
if (pdn && pdn->force_32bit_msi && !phb->msi32_support)
return -ENODEV;
return (phb && phb->msi_bmp.bitmap) ? 0 : -ENODEV;
}
static int pnv_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type)
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
struct msi_desc *entry;
struct msi_msg msg;
int hwirq;
unsigned int virq;
int rc;
if (WARN_ON(!phb))
return -ENODEV;
list_for_each_entry(entry, &pdev->msi_list, list) {
if (!entry->msi_attrib.is_64 && !phb->msi32_support) {
pr_warn("%s: Supports only 64-bit MSIs\n",
pci_name(pdev));
return -ENXIO;
}
hwirq = msi_bitmap_alloc_hwirqs(&phb->msi_bmp, 1);
if (hwirq < 0) {
pr_warn("%s: Failed to find a free MSI\n",
pci_name(pdev));
return -ENOSPC;
}
virq = irq_create_mapping(NULL, phb->msi_base + hwirq);
if (virq == NO_IRQ) {
pr_warn("%s: Failed to map MSI to linux irq\n",
pci_name(pdev));
msi_bitmap_free_hwirqs(&phb->msi_bmp, hwirq, 1);
return -ENOMEM;
}
rc = phb->msi_setup(phb, pdev, phb->msi_base + hwirq,
virq, entry->msi_attrib.is_64, &msg);
if (rc) {
pr_warn("%s: Failed to setup MSI\n", pci_name(pdev));
irq_dispose_mapping(virq);
msi_bitmap_free_hwirqs(&phb->msi_bmp, hwirq, 1);
return rc;
}
irq_set_msi_desc(virq, entry);
write_msi_msg(virq, &msg);
}
return 0;
}
static void pnv_teardown_msi_irqs(struct pci_dev *pdev)
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
struct msi_desc *entry;
if (WARN_ON(!phb))
return;
list_for_each_entry(entry, &pdev->msi_list, list) {
if (entry->irq == NO_IRQ)
continue;
irq_set_msi_desc(entry->irq, NULL);
msi_bitmap_free_hwirqs(&phb->msi_bmp,
virq_to_hw(entry->irq) - phb->msi_base, 1);
irq_dispose_mapping(entry->irq);
}
}
#endif /* CONFIG_PCI_MSI */
static void pnv_pci_dump_p7ioc_diag_data(struct pnv_phb *phb)
{
struct OpalIoP7IOCPhbErrorData *data = &phb->diag.p7ioc;
int i;
pr_info("PHB %d diagnostic data:\n", phb->hose->global_number);
pr_info(" brdgCtl = 0x%08x\n", data->brdgCtl);
pr_info(" portStatusReg = 0x%08x\n", data->portStatusReg);
pr_info(" rootCmplxStatus = 0x%08x\n", data->rootCmplxStatus);
pr_info(" busAgentStatus = 0x%08x\n", data->busAgentStatus);
pr_info(" deviceStatus = 0x%08x\n", data->deviceStatus);
pr_info(" slotStatus = 0x%08x\n", data->slotStatus);
pr_info(" linkStatus = 0x%08x\n", data->linkStatus);
pr_info(" devCmdStatus = 0x%08x\n", data->devCmdStatus);
pr_info(" devSecStatus = 0x%08x\n", data->devSecStatus);
pr_info(" rootErrorStatus = 0x%08x\n", data->rootErrorStatus);
pr_info(" uncorrErrorStatus = 0x%08x\n", data->uncorrErrorStatus);
pr_info(" corrErrorStatus = 0x%08x\n", data->corrErrorStatus);
pr_info(" tlpHdr1 = 0x%08x\n", data->tlpHdr1);
pr_info(" tlpHdr2 = 0x%08x\n", data->tlpHdr2);
pr_info(" tlpHdr3 = 0x%08x\n", data->tlpHdr3);
pr_info(" tlpHdr4 = 0x%08x\n", data->tlpHdr4);
pr_info(" sourceId = 0x%08x\n", data->sourceId);
pr_info(" errorClass = 0x%016llx\n", data->errorClass);
pr_info(" correlator = 0x%016llx\n", data->correlator);
pr_info(" p7iocPlssr = 0x%016llx\n", data->p7iocPlssr);
pr_info(" p7iocCsr = 0x%016llx\n", data->p7iocCsr);
pr_info(" lemFir = 0x%016llx\n", data->lemFir);
pr_info(" lemErrorMask = 0x%016llx\n", data->lemErrorMask);
pr_info(" lemWOF = 0x%016llx\n", data->lemWOF);
pr_info(" phbErrorStatus = 0x%016llx\n", data->phbErrorStatus);
pr_info(" phbFirstErrorStatus = 0x%016llx\n", data->phbFirstErrorStatus);
pr_info(" phbErrorLog0 = 0x%016llx\n", data->phbErrorLog0);
pr_info(" phbErrorLog1 = 0x%016llx\n", data->phbErrorLog1);
pr_info(" mmioErrorStatus = 0x%016llx\n", data->mmioErrorStatus);
pr_info(" mmioFirstErrorStatus = 0x%016llx\n", data->mmioFirstErrorStatus);
pr_info(" mmioErrorLog0 = 0x%016llx\n", data->mmioErrorLog0);
pr_info(" mmioErrorLog1 = 0x%016llx\n", data->mmioErrorLog1);
pr_info(" dma0ErrorStatus = 0x%016llx\n", data->dma0ErrorStatus);
pr_info(" dma0FirstErrorStatus = 0x%016llx\n", data->dma0FirstErrorStatus);
pr_info(" dma0ErrorLog0 = 0x%016llx\n", data->dma0ErrorLog0);
pr_info(" dma0ErrorLog1 = 0x%016llx\n", data->dma0ErrorLog1);
pr_info(" dma1ErrorStatus = 0x%016llx\n", data->dma1ErrorStatus);
pr_info(" dma1FirstErrorStatus = 0x%016llx\n", data->dma1FirstErrorStatus);
pr_info(" dma1ErrorLog0 = 0x%016llx\n", data->dma1ErrorLog0);
pr_info(" dma1ErrorLog1 = 0x%016llx\n", data->dma1ErrorLog1);
for (i = 0; i < OPAL_P7IOC_NUM_PEST_REGS; i++) {
if ((data->pestA[i] >> 63) == 0 &&
(data->pestB[i] >> 63) == 0)
continue;
pr_info(" PE[%3d] PESTA = 0x%016llx\n", i, data->pestA[i]);
pr_info(" PESTB = 0x%016llx\n", data->pestB[i]);
}
}
static void pnv_pci_dump_phb_diag_data(struct pnv_phb *phb)
{
switch(phb->model) {
case PNV_PHB_MODEL_P7IOC:
pnv_pci_dump_p7ioc_diag_data(phb);
break;
default:
pr_warning("PCI %d: Can't decode this PHB diag data\n",
phb->hose->global_number);
}
}
static void pnv_pci_handle_eeh_config(struct pnv_phb *phb, u32 pe_no)
{
unsigned long flags, rc;
int has_diag;
spin_lock_irqsave(&phb->lock, flags);
rc = opal_pci_get_phb_diag_data2(phb->opal_id, phb->diag.blob,
PNV_PCI_DIAG_BUF_SIZE);
has_diag = (rc == OPAL_SUCCESS);
rc = opal_pci_eeh_freeze_clear(phb->opal_id, pe_no,
OPAL_EEH_ACTION_CLEAR_FREEZE_ALL);
if (rc) {
pr_warning("PCI %d: Failed to clear EEH freeze state"
" for PE#%d, err %ld\n",
phb->hose->global_number, pe_no, rc);
/* For now, let's only display the diag buffer when we fail to clear
* the EEH status. We'll do more sensible things later when we have
* proper EEH support. We need to make sure we don't pollute ourselves
* with the normal errors generated when probing empty slots
*/
if (has_diag)
pnv_pci_dump_phb_diag_data(phb);
else
pr_warning("PCI %d: No diag data available\n",
phb->hose->global_number);
}
spin_unlock_irqrestore(&phb->lock, flags);
}
static void pnv_pci_config_check_eeh(struct pnv_phb *phb,
struct device_node *dn)
{
s64 rc;
u8 fstate;
u16 pcierr;
u32 pe_no;
/*
* Get the PE#. During the PCI probe stage, we might not
* setup that yet. So all ER errors should be mapped to
* PE#0
*/
pe_no = PCI_DN(dn)->pe_number;
if (pe_no == IODA_INVALID_PE)
pe_no = 0;
/* Read freeze status */
rc = opal_pci_eeh_freeze_status(phb->opal_id, pe_no, &fstate, &pcierr,
NULL);
if (rc) {
pr_warning("%s: Can't read EEH status (PE#%d) for "
"%s, err %lld\n",
__func__, pe_no, dn->full_name, rc);
return;
}
cfg_dbg(" -> EEH check, bdfn=%04x PE#%d fstate=%x\n",
(PCI_DN(dn)->busno << 8) | (PCI_DN(dn)->devfn),
pe_no, fstate);
if (fstate != 0)
pnv_pci_handle_eeh_config(phb, pe_no);
}
int pnv_pci_cfg_read(struct device_node *dn,
int where, int size, u32 *val)
{
struct pci_dn *pdn = PCI_DN(dn);
struct pnv_phb *phb = pdn->phb->private_data;
u32 bdfn = (pdn->busno << 8) | pdn->devfn;
#ifdef CONFIG_EEH
struct eeh_pe *phb_pe = NULL;
#endif
s64 rc;
switch (size) {
case 1: {
u8 v8;
rc = opal_pci_config_read_byte(phb->opal_id, bdfn, where, &v8);
*val = (rc == OPAL_SUCCESS) ? v8 : 0xff;
break;
}
case 2: {
u16 v16;
rc = opal_pci_config_read_half_word(phb->opal_id, bdfn, where,
&v16);
*val = (rc == OPAL_SUCCESS) ? v16 : 0xffff;
break;
}
case 4: {
u32 v32;
rc = opal_pci_config_read_word(phb->opal_id, bdfn, where, &v32);
*val = (rc == OPAL_SUCCESS) ? v32 : 0xffffffff;
break;
}
default:
return PCIBIOS_FUNC_NOT_SUPPORTED;
}
cfg_dbg("%s: bus: %x devfn: %x +%x/%x -> %08x\n",
__func__, pdn->busno, pdn->devfn, where, size, *val);
/*
* Check if the specified PE has been put into frozen
* state. On the other hand, we needn't do that while
* the PHB has been put into frozen state because of
* PHB-fatal errors.
*/
#ifdef CONFIG_EEH
phb_pe = eeh_phb_pe_get(pdn->phb);
if (phb_pe && (phb_pe->state & EEH_PE_ISOLATED))
return PCIBIOS_SUCCESSFUL;
if (phb->eeh_state & PNV_EEH_STATE_ENABLED) {
if (*val == EEH_IO_ERROR_VALUE(size) &&
eeh_dev_check_failure(of_node_to_eeh_dev(dn)))
return PCIBIOS_DEVICE_NOT_FOUND;
} else {
pnv_pci_config_check_eeh(phb, dn);
}
#else
pnv_pci_config_check_eeh(phb, dn);
#endif
return PCIBIOS_SUCCESSFUL;
}
int pnv_pci_cfg_write(struct device_node *dn,
int where, int size, u32 val)
{
struct pci_dn *pdn = PCI_DN(dn);
struct pnv_phb *phb = pdn->phb->private_data;
u32 bdfn = (pdn->busno << 8) | pdn->devfn;
cfg_dbg("%s: bus: %x devfn: %x +%x/%x -> %08x\n",
pdn->busno, pdn->devfn, where, size, val);
switch (size) {
case 1:
opal_pci_config_write_byte(phb->opal_id, bdfn, where, val);
break;
case 2:
opal_pci_config_write_half_word(phb->opal_id, bdfn, where, val);
break;
case 4:
opal_pci_config_write_word(phb->opal_id, bdfn, where, val);
break;
default:
return PCIBIOS_FUNC_NOT_SUPPORTED;
}
/* Check if the PHB got frozen due to an error (no response) */
#ifdef CONFIG_EEH
if (!(phb->eeh_state & PNV_EEH_STATE_ENABLED))
pnv_pci_config_check_eeh(phb, dn);
#else
pnv_pci_config_check_eeh(phb, dn);
#endif
return PCIBIOS_SUCCESSFUL;
}
static int pnv_pci_read_config(struct pci_bus *bus,
unsigned int devfn,
int where, int size, u32 *val)
{
struct device_node *dn, *busdn = pci_bus_to_OF_node(bus);
struct pci_dn *pdn;
for (dn = busdn->child; dn; dn = dn->sibling) {
pdn = PCI_DN(dn);
if (pdn && pdn->devfn == devfn)
return pnv_pci_cfg_read(dn, where, size, val);
}
*val = 0xFFFFFFFF;
return PCIBIOS_DEVICE_NOT_FOUND;
}
static int pnv_pci_write_config(struct pci_bus *bus,
unsigned int devfn,
int where, int size, u32 val)
{
struct device_node *dn, *busdn = pci_bus_to_OF_node(bus);
struct pci_dn *pdn;
for (dn = busdn->child; dn; dn = dn->sibling) {
pdn = PCI_DN(dn);
if (pdn && pdn->devfn == devfn)
return pnv_pci_cfg_write(dn, where, size, val);
}
return PCIBIOS_DEVICE_NOT_FOUND;
}
struct pci_ops pnv_pci_ops = {
.read = pnv_pci_read_config,
.write = pnv_pci_write_config,
};
static int pnv_tce_build(struct iommu_table *tbl, long index, long npages,
unsigned long uaddr, enum dma_data_direction direction,
struct dma_attrs *attrs)
{
u64 proto_tce;
u64 *tcep, *tces;
u64 rpn;
proto_tce = TCE_PCI_READ; // Read allowed
if (direction != DMA_TO_DEVICE)
proto_tce |= TCE_PCI_WRITE;
tces = tcep = ((u64 *)tbl->it_base) + index - tbl->it_offset;
rpn = __pa(uaddr) >> TCE_SHIFT;
while (npages--)
*(tcep++) = proto_tce | (rpn++ << TCE_RPN_SHIFT);
/* Some implementations won't cache invalid TCEs and thus may not
* need that flush. We'll probably turn it_type into a bit mask
* of flags if that becomes the case
*/
if (tbl->it_type & TCE_PCI_SWINV_CREATE)
pnv_pci_ioda_tce_invalidate(tbl, tces, tcep - 1);
return 0;
}
static void pnv_tce_free(struct iommu_table *tbl, long index, long npages)
{
u64 *tcep, *tces;
tces = tcep = ((u64 *)tbl->it_base) + index - tbl->it_offset;
while (npages--)
*(tcep++) = 0;
if (tbl->it_type & TCE_PCI_SWINV_FREE)
pnv_pci_ioda_tce_invalidate(tbl, tces, tcep - 1);
}
static unsigned long pnv_tce_get(struct iommu_table *tbl, long index)
{
return ((u64 *)tbl->it_base)[index - tbl->it_offset];
}
void pnv_pci_setup_iommu_table(struct iommu_table *tbl,
void *tce_mem, u64 tce_size,
u64 dma_offset)
{
tbl->it_blocksize = 16;
tbl->it_base = (unsigned long)tce_mem;
tbl->it_offset = dma_offset >> IOMMU_PAGE_SHIFT;
tbl->it_index = 0;
tbl->it_size = tce_size >> 3;
tbl->it_busno = 0;
tbl->it_type = TCE_PCI;
}
static struct iommu_table *pnv_pci_setup_bml_iommu(struct pci_controller *hose)
{
struct iommu_table *tbl;
const __be64 *basep, *swinvp;
const __be32 *sizep;
basep = of_get_property(hose->dn, "linux,tce-base", NULL);
sizep = of_get_property(hose->dn, "linux,tce-size", NULL);
if (basep == NULL || sizep == NULL) {
pr_err("PCI: %s has missing tce entries !\n",
hose->dn->full_name);
return NULL;
}
tbl = kzalloc_node(sizeof(struct iommu_table), GFP_KERNEL, hose->node);
if (WARN_ON(!tbl))
return NULL;
pnv_pci_setup_iommu_table(tbl, __va(be64_to_cpup(basep)),
be32_to_cpup(sizep), 0);
iommu_init_table(tbl, hose->node);
iommu_register_group(tbl, pci_domain_nr(hose->bus), 0);
/* Deal with SW invalidated TCEs when needed (BML way) */
swinvp = of_get_property(hose->dn, "linux,tce-sw-invalidate-info",
NULL);
if (swinvp) {
tbl->it_busno = swinvp[1];
tbl->it_index = (unsigned long)ioremap(swinvp[0], 8);
tbl->it_type = TCE_PCI_SWINV_CREATE | TCE_PCI_SWINV_FREE;
}
return tbl;
}
static void pnv_pci_dma_fallback_setup(struct pci_controller *hose,
struct pci_dev *pdev)
{
struct device_node *np = pci_bus_to_OF_node(hose->bus);
struct pci_dn *pdn;
if (np == NULL)
return;
pdn = PCI_DN(np);
if (!pdn->iommu_table)
pdn->iommu_table = pnv_pci_setup_bml_iommu(hose);
if (!pdn->iommu_table)
return;
set_iommu_table_base(&pdev->dev, pdn->iommu_table);
}
static void pnv_pci_dma_dev_setup(struct pci_dev *pdev)
{
struct pci_controller *hose = pci_bus_to_host(pdev->bus);
struct pnv_phb *phb = hose->private_data;
/* If we have no phb structure, try to setup a fallback based on
* the device-tree (RTAS PCI for example)
*/
if (phb && phb->dma_dev_setup)
phb->dma_dev_setup(phb, pdev);
else
pnv_pci_dma_fallback_setup(hose, pdev);
}
void pnv_pci_shutdown(void)
{
struct pci_controller *hose;
list_for_each_entry(hose, &hose_list, list_node) {
struct pnv_phb *phb = hose->private_data;
if (phb && phb->shutdown)
phb->shutdown(phb);
}
}
/* Fixup wrong class code in p7ioc and p8 root complex */
static void pnv_p7ioc_rc_quirk(struct pci_dev *dev)
{
dev->class = PCI_CLASS_BRIDGE_PCI << 8;
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_IBM, 0x3b9, pnv_p7ioc_rc_quirk);
static int pnv_pci_probe_mode(struct pci_bus *bus)
{
struct pci_controller *hose = pci_bus_to_host(bus);
const __be64 *tstamp;
u64 now, target;
/* We hijack this as a way to ensure we have waited long
* enough since the reset was lifted on the PCI bus
*/
if (bus != hose->bus)
return PCI_PROBE_NORMAL;
tstamp = of_get_property(hose->dn, "reset-clear-timestamp", NULL);
if (!tstamp || !*tstamp)
return PCI_PROBE_NORMAL;
now = mftb() / tb_ticks_per_usec;
target = (be64_to_cpup(tstamp) / tb_ticks_per_usec)
+ PCI_RESET_DELAY_US;
pr_devel("pci %04d: Reset target: 0x%llx now: 0x%llx\n",
hose->global_number, target, now);
if (now < target)
msleep((target - now + 999) / 1000);
return PCI_PROBE_NORMAL;
}
void __init pnv_pci_init(void)
{
struct device_node *np;
pci_add_flags(PCI_CAN_SKIP_ISA_ALIGN);
/* OPAL absent, try POPAL first then RTAS detection of PHBs */
if (!firmware_has_feature(FW_FEATURE_OPAL)) {
#ifdef CONFIG_PPC_POWERNV_RTAS
init_pci_config_tokens();
find_and_init_phbs();
#endif /* CONFIG_PPC_POWERNV_RTAS */
}
/* OPAL is here, do our normal stuff */
else {
int found_ioda = 0;
/* Look for IODA IO-Hubs. We don't support mixing IODA
* and p5ioc2 due to the need to change some global
* probing flags
*/
for_each_compatible_node(np, NULL, "ibm,ioda-hub") {
pnv_pci_init_ioda_hub(np);
found_ioda = 1;
}
/* Look for p5ioc2 IO-Hubs */
if (!found_ioda)
for_each_compatible_node(np, NULL, "ibm,p5ioc2")
pnv_pci_init_p5ioc2_hub(np);
/* Look for ioda2 built-in PHB3's */
for_each_compatible_node(np, NULL, "ibm,ioda2-phb")
pnv_pci_init_ioda2_phb(np);
}
/* Setup the linkage between OF nodes and PHBs */
pci_devs_phb_init();
/* Configure IOMMU DMA hooks */
ppc_md.pci_dma_dev_setup = pnv_pci_dma_dev_setup;
ppc_md.tce_build = pnv_tce_build;
ppc_md.tce_free = pnv_tce_free;
ppc_md.tce_get = pnv_tce_get;
ppc_md.pci_probe_mode = pnv_pci_probe_mode;
set_pci_dma_ops(&dma_iommu_ops);
/* Configure MSIs */
#ifdef CONFIG_PCI_MSI
ppc_md.msi_check_device = pnv_msi_check_device;
ppc_md.setup_msi_irqs = pnv_setup_msi_irqs;
ppc_md.teardown_msi_irqs = pnv_teardown_msi_irqs;
#endif
}