linux-stable/drivers/gpio/gpio-pl061.c
Linus Walleij 26ba9cd48f gpio: pl061: assign the apropriate handler for irqs
The PL061 can handle level IRQs and edge IRQs, however it is
just utilizing handle_simple_irq() for all IRQs. Inspired by
Stefan Agners patch to vf610, this assigns the right handler
depending on what type is set up, and after this
handle_bad_irq() is only used as default and if the type is
not specified, as is done in the OMAP driver: defining the
IRQ type is really not optional for this driver.

The interrupt handler was just writing the interrupt clearing
register for all lines that were high when entering the handling
loop, this is wrong: that register is only supposed to be
written (on a per-line basis) for edge IRQs, so this ACK
was moved to the .irq_ack() callback as is proper.

Tested with PL061 on the ARM RealView PB11MPCore and the
MMC/SC card detect GPIO.

Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-15 18:03:07 +02:00

468 lines
12 KiB
C

/*
* Copyright (C) 2008, 2009 Provigent Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Driver for the ARM PrimeCell(tm) General Purpose Input/Output (PL061)
*
* Data sheet: ARM DDI 0190B, September 2000
*/
#include <linux/spinlock.h>
#include <linux/errno.h>
#include <linux/module.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/irqchip/chained_irq.h>
#include <linux/bitops.h>
#include <linux/gpio.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
#include <linux/slab.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm.h>
#define GPIODIR 0x400
#define GPIOIS 0x404
#define GPIOIBE 0x408
#define GPIOIEV 0x40C
#define GPIOIE 0x410
#define GPIORIS 0x414
#define GPIOMIS 0x418
#define GPIOIC 0x41C
#define PL061_GPIO_NR 8
#ifdef CONFIG_PM
struct pl061_context_save_regs {
u8 gpio_data;
u8 gpio_dir;
u8 gpio_is;
u8 gpio_ibe;
u8 gpio_iev;
u8 gpio_ie;
};
#endif
struct pl061_gpio {
spinlock_t lock;
void __iomem *base;
struct gpio_chip gc;
bool uses_pinctrl;
#ifdef CONFIG_PM
struct pl061_context_save_regs csave_regs;
#endif
};
static int pl061_gpio_request(struct gpio_chip *gc, unsigned offset)
{
/*
* Map back to global GPIO space and request muxing, the direction
* parameter does not matter for this controller.
*/
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
int gpio = gc->base + offset;
if (chip->uses_pinctrl)
return pinctrl_request_gpio(gpio);
return 0;
}
static void pl061_gpio_free(struct gpio_chip *gc, unsigned offset)
{
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
int gpio = gc->base + offset;
if (chip->uses_pinctrl)
pinctrl_free_gpio(gpio);
}
static int pl061_direction_input(struct gpio_chip *gc, unsigned offset)
{
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
unsigned long flags;
unsigned char gpiodir;
if (offset >= gc->ngpio)
return -EINVAL;
spin_lock_irqsave(&chip->lock, flags);
gpiodir = readb(chip->base + GPIODIR);
gpiodir &= ~(BIT(offset));
writeb(gpiodir, chip->base + GPIODIR);
spin_unlock_irqrestore(&chip->lock, flags);
return 0;
}
static int pl061_direction_output(struct gpio_chip *gc, unsigned offset,
int value)
{
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
unsigned long flags;
unsigned char gpiodir;
if (offset >= gc->ngpio)
return -EINVAL;
spin_lock_irqsave(&chip->lock, flags);
writeb(!!value << offset, chip->base + (BIT(offset + 2)));
gpiodir = readb(chip->base + GPIODIR);
gpiodir |= BIT(offset);
writeb(gpiodir, chip->base + GPIODIR);
/*
* gpio value is set again, because pl061 doesn't allow to set value of
* a gpio pin before configuring it in OUT mode.
*/
writeb(!!value << offset, chip->base + (BIT(offset + 2)));
spin_unlock_irqrestore(&chip->lock, flags);
return 0;
}
static int pl061_get_value(struct gpio_chip *gc, unsigned offset)
{
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
return !!readb(chip->base + (BIT(offset + 2)));
}
static void pl061_set_value(struct gpio_chip *gc, unsigned offset, int value)
{
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
writeb(!!value << offset, chip->base + (BIT(offset + 2)));
}
static int pl061_irq_type(struct irq_data *d, unsigned trigger)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
int offset = irqd_to_hwirq(d);
unsigned long flags;
u8 gpiois, gpioibe, gpioiev;
u8 bit = BIT(offset);
if (offset < 0 || offset >= PL061_GPIO_NR)
return -EINVAL;
if ((trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) &&
(trigger & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)))
{
dev_err(gc->dev,
"trying to configure line %d for both level and edge "
"detection, choose one!\n",
offset);
return -EINVAL;
}
spin_lock_irqsave(&chip->lock, flags);
gpioiev = readb(chip->base + GPIOIEV);
gpiois = readb(chip->base + GPIOIS);
gpioibe = readb(chip->base + GPIOIBE);
if (trigger & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
bool polarity = trigger & IRQ_TYPE_LEVEL_HIGH;
/* Disable edge detection */
gpioibe &= ~bit;
/* Enable level detection */
gpiois |= bit;
/* Select polarity */
if (polarity)
gpioiev |= bit;
else
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_level_irq);
dev_dbg(gc->dev, "line %d: IRQ on %s level\n",
offset,
polarity ? "HIGH" : "LOW");
} else if ((trigger & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) {
/* Disable level detection */
gpiois &= ~bit;
/* Select both edges, setting this makes GPIOEV be ignored */
gpioibe |= bit;
irq_set_handler_locked(d, handle_edge_irq);
dev_dbg(gc->dev, "line %d: IRQ on both edges\n", offset);
} else if ((trigger & IRQ_TYPE_EDGE_RISING) ||
(trigger & IRQ_TYPE_EDGE_FALLING)) {
bool rising = trigger & IRQ_TYPE_EDGE_RISING;
/* Disable level detection */
gpiois &= ~bit;
/* Clear detection on both edges */
gpioibe &= ~bit;
/* Select edge */
if (rising)
gpioiev |= bit;
else
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_edge_irq);
dev_dbg(gc->dev, "line %d: IRQ on %s edge\n",
offset,
rising ? "RISING" : "FALLING");
} else {
/* No trigger: disable everything */
gpiois &= ~bit;
gpioibe &= ~bit;
gpioiev &= ~bit;
irq_set_handler_locked(d, handle_bad_irq);
dev_warn(gc->dev, "no trigger selected for line %d\n",
offset);
}
writeb(gpiois, chip->base + GPIOIS);
writeb(gpioibe, chip->base + GPIOIBE);
writeb(gpioiev, chip->base + GPIOIEV);
spin_unlock_irqrestore(&chip->lock, flags);
return 0;
}
static void pl061_irq_handler(struct irq_desc *desc)
{
unsigned long pending;
int offset;
struct gpio_chip *gc = irq_desc_get_handler_data(desc);
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
struct irq_chip *irqchip = irq_desc_get_chip(desc);
chained_irq_enter(irqchip, desc);
pending = readb(chip->base + GPIOMIS);
if (pending) {
for_each_set_bit(offset, &pending, PL061_GPIO_NR)
generic_handle_irq(irq_find_mapping(gc->irqdomain,
offset));
}
chained_irq_exit(irqchip, desc);
}
static void pl061_irq_mask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
u8 gpioie;
spin_lock(&chip->lock);
gpioie = readb(chip->base + GPIOIE) & ~mask;
writeb(gpioie, chip->base + GPIOIE);
spin_unlock(&chip->lock);
}
static void pl061_irq_unmask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
u8 gpioie;
spin_lock(&chip->lock);
gpioie = readb(chip->base + GPIOIE) | mask;
writeb(gpioie, chip->base + GPIOIE);
spin_unlock(&chip->lock);
}
/**
* pl061_irq_ack() - ACK an edge IRQ
* @d: IRQ data for this IRQ
*
* This gets called from the edge IRQ handler to ACK the edge IRQ
* in the GPIOIC (interrupt-clear) register. For level IRQs this is
* not needed: these go away when the level signal goes away.
*/
static void pl061_irq_ack(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
u8 mask = BIT(irqd_to_hwirq(d) % PL061_GPIO_NR);
spin_lock(&chip->lock);
writeb(mask, chip->base + GPIOIC);
spin_unlock(&chip->lock);
}
static struct irq_chip pl061_irqchip = {
.name = "pl061",
.irq_ack = pl061_irq_ack,
.irq_mask = pl061_irq_mask,
.irq_unmask = pl061_irq_unmask,
.irq_set_type = pl061_irq_type,
};
static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
{
struct device *dev = &adev->dev;
struct pl061_platform_data *pdata = dev_get_platdata(dev);
struct pl061_gpio *chip;
int ret, irq, i, irq_base;
chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
if (chip == NULL)
return -ENOMEM;
if (pdata) {
chip->gc.base = pdata->gpio_base;
irq_base = pdata->irq_base;
if (irq_base <= 0) {
dev_err(&adev->dev, "invalid IRQ base in pdata\n");
return -ENODEV;
}
} else {
chip->gc.base = -1;
irq_base = 0;
}
chip->base = devm_ioremap_resource(dev, &adev->res);
if (IS_ERR(chip->base))
return PTR_ERR(chip->base);
spin_lock_init(&chip->lock);
if (of_property_read_bool(dev->of_node, "gpio-ranges"))
chip->uses_pinctrl = true;
chip->gc.request = pl061_gpio_request;
chip->gc.free = pl061_gpio_free;
chip->gc.direction_input = pl061_direction_input;
chip->gc.direction_output = pl061_direction_output;
chip->gc.get = pl061_get_value;
chip->gc.set = pl061_set_value;
chip->gc.ngpio = PL061_GPIO_NR;
chip->gc.label = dev_name(dev);
chip->gc.dev = dev;
chip->gc.owner = THIS_MODULE;
ret = gpiochip_add(&chip->gc);
if (ret)
return ret;
/*
* irq_chip support
*/
writeb(0, chip->base + GPIOIE); /* disable irqs */
irq = adev->irq[0];
if (irq < 0) {
dev_err(&adev->dev, "invalid IRQ\n");
return -ENODEV;
}
ret = gpiochip_irqchip_add(&chip->gc, &pl061_irqchip,
irq_base, handle_bad_irq,
IRQ_TYPE_NONE);
if (ret) {
dev_info(&adev->dev, "could not add irqchip\n");
return ret;
}
gpiochip_set_chained_irqchip(&chip->gc, &pl061_irqchip,
irq, pl061_irq_handler);
for (i = 0; i < PL061_GPIO_NR; i++) {
if (pdata) {
if (pdata->directions & (BIT(i)))
pl061_direction_output(&chip->gc, i,
pdata->values & (BIT(i)));
else
pl061_direction_input(&chip->gc, i);
}
}
amba_set_drvdata(adev, chip);
dev_info(&adev->dev, "PL061 GPIO chip @%pa registered\n",
&adev->res.start);
return 0;
}
#ifdef CONFIG_PM
static int pl061_suspend(struct device *dev)
{
struct pl061_gpio *chip = dev_get_drvdata(dev);
int offset;
chip->csave_regs.gpio_data = 0;
chip->csave_regs.gpio_dir = readb(chip->base + GPIODIR);
chip->csave_regs.gpio_is = readb(chip->base + GPIOIS);
chip->csave_regs.gpio_ibe = readb(chip->base + GPIOIBE);
chip->csave_regs.gpio_iev = readb(chip->base + GPIOIEV);
chip->csave_regs.gpio_ie = readb(chip->base + GPIOIE);
for (offset = 0; offset < PL061_GPIO_NR; offset++) {
if (chip->csave_regs.gpio_dir & (BIT(offset)))
chip->csave_regs.gpio_data |=
pl061_get_value(&chip->gc, offset) << offset;
}
return 0;
}
static int pl061_resume(struct device *dev)
{
struct pl061_gpio *chip = dev_get_drvdata(dev);
int offset;
for (offset = 0; offset < PL061_GPIO_NR; offset++) {
if (chip->csave_regs.gpio_dir & (BIT(offset)))
pl061_direction_output(&chip->gc, offset,
chip->csave_regs.gpio_data &
(BIT(offset)));
else
pl061_direction_input(&chip->gc, offset);
}
writeb(chip->csave_regs.gpio_is, chip->base + GPIOIS);
writeb(chip->csave_regs.gpio_ibe, chip->base + GPIOIBE);
writeb(chip->csave_regs.gpio_iev, chip->base + GPIOIEV);
writeb(chip->csave_regs.gpio_ie, chip->base + GPIOIE);
return 0;
}
static const struct dev_pm_ops pl061_dev_pm_ops = {
.suspend = pl061_suspend,
.resume = pl061_resume,
.freeze = pl061_suspend,
.restore = pl061_resume,
};
#endif
static struct amba_id pl061_ids[] = {
{
.id = 0x00041061,
.mask = 0x000fffff,
},
{ 0, 0 },
};
MODULE_DEVICE_TABLE(amba, pl061_ids);
static struct amba_driver pl061_gpio_driver = {
.drv = {
.name = "pl061_gpio",
#ifdef CONFIG_PM
.pm = &pl061_dev_pm_ops,
#endif
},
.id_table = pl061_ids,
.probe = pl061_probe,
};
static int __init pl061_gpio_init(void)
{
return amba_driver_register(&pl061_gpio_driver);
}
module_init(pl061_gpio_init);
MODULE_AUTHOR("Baruch Siach <baruch@tkos.co.il>");
MODULE_DESCRIPTION("PL061 GPIO driver");
MODULE_LICENSE("GPL");