mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-08-28 20:02:17 +00:00
![Gustavo A. R. Silva](/assets/img/avatar_default.png)
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
307 lines
7.6 KiB
C
307 lines
7.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/console.h>
|
|
#include <linux/io.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/platform_device.h>
|
|
|
|
#include "8250.h"
|
|
|
|
/*
|
|
* This hardware is similar to 8250, but its register map is a bit different:
|
|
* - MMIO32 (regshift = 2)
|
|
* - FCR is not at 2, but 3
|
|
* - LCR and MCR are not at 3 and 4, they share 4
|
|
* - No SCR (Instead, CHAR can be used as a scratch register)
|
|
* - Divisor latch at 9, no divisor latch access bit
|
|
*/
|
|
|
|
#define UNIPHIER_UART_REGSHIFT 2
|
|
|
|
/* bit[15:8] = CHAR, bit[7:0] = FCR */
|
|
#define UNIPHIER_UART_CHAR_FCR (3 << (UNIPHIER_UART_REGSHIFT))
|
|
/* bit[15:8] = LCR, bit[7:0] = MCR */
|
|
#define UNIPHIER_UART_LCR_MCR (4 << (UNIPHIER_UART_REGSHIFT))
|
|
/* Divisor Latch Register */
|
|
#define UNIPHIER_UART_DLR (9 << (UNIPHIER_UART_REGSHIFT))
|
|
|
|
struct uniphier8250_priv {
|
|
int line;
|
|
struct clk *clk;
|
|
spinlock_t atomic_write_lock;
|
|
};
|
|
|
|
#ifdef CONFIG_SERIAL_8250_CONSOLE
|
|
static int __init uniphier_early_console_setup(struct earlycon_device *device,
|
|
const char *options)
|
|
{
|
|
if (!device->port.membase)
|
|
return -ENODEV;
|
|
|
|
/* This hardware always expects MMIO32 register interface. */
|
|
device->port.iotype = UPIO_MEM32;
|
|
device->port.regshift = UNIPHIER_UART_REGSHIFT;
|
|
|
|
/*
|
|
* Do not touch the divisor register in early_serial8250_setup();
|
|
* we assume it has been initialized by a boot loader.
|
|
*/
|
|
device->baud = 0;
|
|
|
|
return early_serial8250_setup(device, options);
|
|
}
|
|
OF_EARLYCON_DECLARE(uniphier, "socionext,uniphier-uart",
|
|
uniphier_early_console_setup);
|
|
#endif
|
|
|
|
/*
|
|
* The register map is slightly different from that of 8250.
|
|
* IO callbacks must be overridden for correct access to FCR, LCR, MCR and SCR.
|
|
*/
|
|
static unsigned int uniphier_serial_in(struct uart_port *p, int offset)
|
|
{
|
|
unsigned int valshift = 0;
|
|
|
|
switch (offset) {
|
|
case UART_SCR:
|
|
/* No SCR for this hardware. Use CHAR as a scratch register */
|
|
valshift = 8;
|
|
offset = UNIPHIER_UART_CHAR_FCR;
|
|
break;
|
|
case UART_LCR:
|
|
valshift = 8;
|
|
fallthrough;
|
|
case UART_MCR:
|
|
offset = UNIPHIER_UART_LCR_MCR;
|
|
break;
|
|
default:
|
|
offset <<= UNIPHIER_UART_REGSHIFT;
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* The return value must be masked with 0xff because some registers
|
|
* share the same offset that must be accessed by 32-bit write/read.
|
|
* 8 or 16 bit access to this hardware result in unexpected behavior.
|
|
*/
|
|
return (readl(p->membase + offset) >> valshift) & 0xff;
|
|
}
|
|
|
|
static void uniphier_serial_out(struct uart_port *p, int offset, int value)
|
|
{
|
|
unsigned int valshift = 0;
|
|
bool normal = false;
|
|
|
|
switch (offset) {
|
|
case UART_SCR:
|
|
/* No SCR for this hardware. Use CHAR as a scratch register */
|
|
valshift = 8;
|
|
fallthrough;
|
|
case UART_FCR:
|
|
offset = UNIPHIER_UART_CHAR_FCR;
|
|
break;
|
|
case UART_LCR:
|
|
valshift = 8;
|
|
/* Divisor latch access bit does not exist. */
|
|
value &= ~UART_LCR_DLAB;
|
|
fallthrough;
|
|
case UART_MCR:
|
|
offset = UNIPHIER_UART_LCR_MCR;
|
|
break;
|
|
default:
|
|
offset <<= UNIPHIER_UART_REGSHIFT;
|
|
normal = true;
|
|
break;
|
|
}
|
|
|
|
if (normal) {
|
|
writel(value, p->membase + offset);
|
|
} else {
|
|
/*
|
|
* Special case: two registers share the same address that
|
|
* must be 32-bit accessed. As this is not longer atomic safe,
|
|
* take a lock just in case.
|
|
*/
|
|
struct uniphier8250_priv *priv = p->private_data;
|
|
unsigned long flags;
|
|
u32 tmp;
|
|
|
|
spin_lock_irqsave(&priv->atomic_write_lock, flags);
|
|
tmp = readl(p->membase + offset);
|
|
tmp &= ~(0xff << valshift);
|
|
tmp |= value << valshift;
|
|
writel(tmp, p->membase + offset);
|
|
spin_unlock_irqrestore(&priv->atomic_write_lock, flags);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* This hardware does not have the divisor latch access bit.
|
|
* The divisor latch register exists at different address.
|
|
* Override dl_read/write callbacks.
|
|
*/
|
|
static int uniphier_serial_dl_read(struct uart_8250_port *up)
|
|
{
|
|
return readl(up->port.membase + UNIPHIER_UART_DLR);
|
|
}
|
|
|
|
static void uniphier_serial_dl_write(struct uart_8250_port *up, int value)
|
|
{
|
|
writel(value, up->port.membase + UNIPHIER_UART_DLR);
|
|
}
|
|
|
|
static int uniphier_uart_probe(struct platform_device *pdev)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
struct uart_8250_port up;
|
|
struct uniphier8250_priv *priv;
|
|
struct resource *regs;
|
|
void __iomem *membase;
|
|
int irq;
|
|
int ret;
|
|
|
|
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
if (!regs) {
|
|
dev_err(dev, "failed to get memory resource\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
membase = devm_ioremap(dev, regs->start, resource_size(regs));
|
|
if (!membase)
|
|
return -ENOMEM;
|
|
|
|
irq = platform_get_irq(pdev, 0);
|
|
if (irq < 0)
|
|
return irq;
|
|
|
|
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
|
if (!priv)
|
|
return -ENOMEM;
|
|
|
|
memset(&up, 0, sizeof(up));
|
|
|
|
ret = of_alias_get_id(dev->of_node, "serial");
|
|
if (ret < 0) {
|
|
dev_err(dev, "failed to get alias id\n");
|
|
return ret;
|
|
}
|
|
up.port.line = ret;
|
|
|
|
priv->clk = devm_clk_get(dev, NULL);
|
|
if (IS_ERR(priv->clk)) {
|
|
dev_err(dev, "failed to get clock\n");
|
|
return PTR_ERR(priv->clk);
|
|
}
|
|
|
|
ret = clk_prepare_enable(priv->clk);
|
|
if (ret)
|
|
return ret;
|
|
|
|
up.port.uartclk = clk_get_rate(priv->clk);
|
|
|
|
spin_lock_init(&priv->atomic_write_lock);
|
|
|
|
up.port.dev = dev;
|
|
up.port.private_data = priv;
|
|
up.port.mapbase = regs->start;
|
|
up.port.mapsize = resource_size(regs);
|
|
up.port.membase = membase;
|
|
up.port.irq = irq;
|
|
|
|
up.port.type = PORT_16550A;
|
|
up.port.iotype = UPIO_MEM32;
|
|
up.port.fifosize = 64;
|
|
up.port.regshift = UNIPHIER_UART_REGSHIFT;
|
|
up.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE;
|
|
up.capabilities = UART_CAP_FIFO;
|
|
|
|
if (of_property_read_bool(dev->of_node, "auto-flow-control"))
|
|
up.capabilities |= UART_CAP_AFE;
|
|
|
|
up.port.serial_in = uniphier_serial_in;
|
|
up.port.serial_out = uniphier_serial_out;
|
|
up.dl_read = uniphier_serial_dl_read;
|
|
up.dl_write = uniphier_serial_dl_write;
|
|
|
|
ret = serial8250_register_8250_port(&up);
|
|
if (ret < 0) {
|
|
dev_err(dev, "failed to register 8250 port\n");
|
|
clk_disable_unprepare(priv->clk);
|
|
return ret;
|
|
}
|
|
priv->line = ret;
|
|
|
|
platform_set_drvdata(pdev, priv);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int uniphier_uart_remove(struct platform_device *pdev)
|
|
{
|
|
struct uniphier8250_priv *priv = platform_get_drvdata(pdev);
|
|
|
|
serial8250_unregister_port(priv->line);
|
|
clk_disable_unprepare(priv->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused uniphier_uart_suspend(struct device *dev)
|
|
{
|
|
struct uniphier8250_priv *priv = dev_get_drvdata(dev);
|
|
struct uart_8250_port *up = serial8250_get_port(priv->line);
|
|
|
|
serial8250_suspend_port(priv->line);
|
|
|
|
if (!uart_console(&up->port) || console_suspend_enabled)
|
|
clk_disable_unprepare(priv->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused uniphier_uart_resume(struct device *dev)
|
|
{
|
|
struct uniphier8250_priv *priv = dev_get_drvdata(dev);
|
|
struct uart_8250_port *up = serial8250_get_port(priv->line);
|
|
int ret;
|
|
|
|
if (!uart_console(&up->port) || console_suspend_enabled) {
|
|
ret = clk_prepare_enable(priv->clk);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
serial8250_resume_port(priv->line);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dev_pm_ops uniphier_uart_pm_ops = {
|
|
SET_SYSTEM_SLEEP_PM_OPS(uniphier_uart_suspend, uniphier_uart_resume)
|
|
};
|
|
|
|
static const struct of_device_id uniphier_uart_match[] = {
|
|
{ .compatible = "socionext,uniphier-uart" },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, uniphier_uart_match);
|
|
|
|
static struct platform_driver uniphier_uart_platform_driver = {
|
|
.probe = uniphier_uart_probe,
|
|
.remove = uniphier_uart_remove,
|
|
.driver = {
|
|
.name = "uniphier-uart",
|
|
.of_match_table = uniphier_uart_match,
|
|
.pm = &uniphier_uart_pm_ops,
|
|
},
|
|
};
|
|
module_platform_driver(uniphier_uart_platform_driver);
|
|
|
|
MODULE_AUTHOR("Masahiro Yamada <yamada.masahiro@socionext.com>");
|
|
MODULE_DESCRIPTION("UniPhier UART driver");
|
|
MODULE_LICENSE("GPL");
|