mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-08-28 20:02:17 +00:00
![Al Cooper](/assets/img/avatar_default.png)
Add a UART driver for the new Broadcom 8250 based STB UART. The new UART is backward compatible with the standard 8250, but has some additional features. The new features include a high accuracy baud rate clock system and DMA support. The driver will use the new optional BAUD MUX clock to select the best one of the four master clocks (81MHz, 108MHz, 64MHz and 48MHz) to feed the baud rate selection logic for any requested baud rate. This allows for more accurate BAUD rates when high speed baud rates are selected. The driver will use the new UART DMA hardware if the UART DMA registers are specified in Device Tree "reg" property. The driver also sets the UPSTAT_AUTOCTS flag when hardware flow control is enabled. This flag is needed for UARTs that don't assert a CTS changed interrupt when CTS changes and AFE (Hardware Flow Control) is enabled. The driver also contains a workaround for a bug in the Synopsis 8250 core. The problem is that at high baud rates, the RX partial FIFO timeout interrupt can occur but there is no RX data (DR not set in the LSR register). In this case the driver will not read the Receive Buffer Register, which clears the interrupt, and the system will get continuous UART interrupts until the next RX character arrives. The fix originally suggested by Synopsis was to read the Receive Buffer Register and discard the character when the DR bit in the LSR was not set, to clear the interrupt. The problem was that occasionally a character would arrive just after the DR bit check and a valid character would be discarded. The fix that was added will clear receive interrupts to stop the interrupt, deassert RTS to insure that no new data can arrive, wait for 1.5 character times for the sender to react to RTS and then check for data and either do a dummy read or a valid read. Debugfs error counters were also added and were used to help create test software that would cause the error condition. The counters can be found at: /sys/kernel/debug/bcm7271-uart/<device-name>/stats This also includes a few fixes for build warnings reported by the kernel test robot. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Link: https://lore.kernel.org/r/20210325185256.16156-3-alcooperx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
44 lines
1.9 KiB
Makefile
44 lines
1.9 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# Makefile for the 8250 serial device drivers.
|
|
#
|
|
|
|
obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o
|
|
8250-y := 8250_core.o
|
|
8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o
|
|
8250_base-y := 8250_port.o
|
|
8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o
|
|
8250_base-$(CONFIG_SERIAL_8250_DWLIB) += 8250_dwlib.o
|
|
8250_base-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
|
|
obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
|
|
obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o
|
|
obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o
|
|
obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o
|
|
obj-$(CONFIG_SERIAL_8250_CS) += serial_cs.o
|
|
obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
|
|
obj-$(CONFIG_SERIAL_8250_ASPEED_VUART) += 8250_aspeed_vuart.o
|
|
obj-$(CONFIG_SERIAL_8250_BCM2835AUX) += 8250_bcm2835aux.o
|
|
obj-$(CONFIG_SERIAL_8250_CONSOLE) += 8250_early.o
|
|
obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o
|
|
obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o
|
|
obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o
|
|
obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) += 8250_exar_st16c554.o
|
|
obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
|
|
obj-$(CONFIG_SERIAL_8250_FSL) += 8250_fsl.o
|
|
obj-$(CONFIG_SERIAL_8250_MEN_MCB) += 8250_men_mcb.o
|
|
obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o
|
|
obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
|
|
obj-$(CONFIG_SERIAL_8250_IOC3) += 8250_ioc3.o
|
|
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
|
|
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
|
|
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
|
|
obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o
|
|
obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
|
|
obj-$(CONFIG_SERIAL_8250_LPSS) += 8250_lpss.o
|
|
obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o
|
|
obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o
|
|
obj-$(CONFIG_SERIAL_8250_TEGRA) += 8250_tegra.o
|
|
obj-$(CONFIG_SERIAL_8250_BCM7271) += 8250_bcm7271.o
|
|
obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o
|
|
|
|
CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt
|