linux-stable/drivers/Makefile
Christoph Hellwig 9ea9b9c483 remove the lightnvm subsystem
Lightnvm supports the OCSSD 1.x and 2.0 specs which were early attempts
to produce Open Channel SSDs and never made it into the NVMe spec
proper.  They have since been superceeded by NVMe enhancements such
as ZNS support.  Remove the support per the deprecation schedule.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210812132308.38486-1-hch@lst.de
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-08-14 15:54:09 -06:00

190 lines
5.3 KiB
Makefile

# SPDX-License-Identifier: GPL-2.0
#
# Makefile for the Linux kernel device drivers.
#
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#
obj-y += irqchip/
obj-y += bus/
obj-$(CONFIG_GENERIC_PHY) += phy/
# GPIO must come after pinctrl as gpios may need to mux pins etc
obj-$(CONFIG_PINCTRL) += pinctrl/
obj-$(CONFIG_GPIOLIB) += gpio/
obj-y += pwm/
obj-y += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
obj-y += video/
obj-y += idle/
# IPMI must come before ACPI in order to provide IPMI opregion support
obj-y += char/ipmi/
obj-$(CONFIG_ACPI) += acpi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
obj-y += amba/
obj-y += clk/
# Many drivers will want to use DMA so this has to be made available
# really early.
obj-$(CONFIG_DMADEVICES) += dma/
# SOC specific infrastructure drivers.
obj-y += soc/
obj-$(CONFIG_VIRTIO) += virtio/
obj-$(CONFIG_VIRTIO_PCI_LIB) += virtio/
obj-$(CONFIG_VDPA) += vdpa/
obj-$(CONFIG_XEN) += xen/
# regulators early, since some subsystems rely on them to initialize
obj-$(CONFIG_REGULATOR) += regulator/
# reset controllers early, since gpu drivers might rely on them to initialize
obj-$(CONFIG_RESET_CONTROLLER) += reset/
# tty/ comes before char/ so that the VT console is the boot-time
# default.
obj-y += tty/
obj-y += char/
# iommu/ comes before gpu as gpu are using iommu controllers
obj-y += iommu/
# gpu/ comes after char for AGP vs DRM startup and after iommu
obj-y += gpu/
obj-$(CONFIG_CONNECTOR) += connector/
# i810fb and intelfb depend on char/agp/
obj-$(CONFIG_FB_I810) += video/fbdev/i810/
obj-$(CONFIG_FB_INTEL) += video/fbdev/intelfb/
obj-$(CONFIG_PARPORT) += parport/
obj-y += base/ block/ misc/ mfd/ nfc/
obj-$(CONFIG_LIBNVDIMM) += nvdimm/
obj-$(CONFIG_DAX) += dax/
obj-$(CONFIG_CXL_BUS) += cxl/
obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf/
obj-$(CONFIG_NUBUS) += nubus/
obj-y += macintosh/
obj-y += scsi/
obj-y += nvme/
obj-$(CONFIG_ATA) += ata/
obj-$(CONFIG_TARGET_CORE) += target/
obj-$(CONFIG_MTD) += mtd/
obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_SPMI) += spmi/
obj-$(CONFIG_HSI) += hsi/
obj-$(CONFIG_SLIMBUS) += slimbus/
obj-y += net/
obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_FUSION) += message/
obj-y += firewire/
obj-$(CONFIG_UIO) += uio/
obj-$(CONFIG_VFIO) += vfio/
obj-y += cdrom/
obj-y += auxdisplay/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
obj-$(CONFIG_ZORRO) += zorro/
obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/
obj-$(CONFIG_PARIDE) += block/paride/
obj-$(CONFIG_TC) += tc/
obj-$(CONFIG_USB_PHY) += usb/
obj-$(CONFIG_USB) += usb/
obj-$(CONFIG_USB_SUPPORT) += usb/
obj-$(CONFIG_PCI) += usb/
obj-$(CONFIG_USB_GADGET) += usb/
obj-$(CONFIG_OF) += usb/
obj-$(CONFIG_SERIO) += input/serio/
obj-$(CONFIG_GAMEPORT) += input/gameport/
obj-$(CONFIG_INPUT) += input/
obj-$(CONFIG_RTC_LIB) += rtc/
obj-y += i2c/ i3c/ media/
obj-$(CONFIG_PPS) += pps/
obj-y += ptp/
obj-$(CONFIG_W1) += w1/
obj-y += power/
obj-$(CONFIG_HWMON) += hwmon/
obj-$(CONFIG_THERMAL) += thermal/
obj-$(CONFIG_WATCHDOG) += watchdog/
obj-$(CONFIG_MD) += md/
obj-$(CONFIG_BT) += bluetooth/
obj-$(CONFIG_ACCESSIBILITY) += accessibility/
obj-$(CONFIG_ISDN) += isdn/
obj-$(CONFIG_EDAC) += edac/
obj-$(CONFIG_EISA) += eisa/
obj-$(CONFIG_PM_OPP) += opp/
obj-$(CONFIG_CPU_FREQ) += cpufreq/
obj-$(CONFIG_CPU_IDLE) += cpuidle/
obj-y += mmc/
obj-$(CONFIG_MEMSTICK) += memstick/
obj-$(CONFIG_NEW_LEDS) += leds/
obj-$(CONFIG_INFINIBAND) += infiniband/
obj-y += firmware/
obj-$(CONFIG_CRYPTO) += crypto/
obj-$(CONFIG_SUPERH) += sh/
obj-y += clocksource/
obj-$(CONFIG_DCA) += dca/
obj-$(CONFIG_HID) += hid/
obj-$(CONFIG_PPC_PS3) += ps3/
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_BCMA) += bcma/
obj-$(CONFIG_VHOST_RING) += vhost/
obj-$(CONFIG_VHOST_IOTLB) += vhost/
obj-$(CONFIG_VHOST) += vhost/
obj-$(CONFIG_VLYNQ) += vlynq/
obj-$(CONFIG_GREYBUS) += greybus/
obj-$(CONFIG_COMEDI) += comedi/
obj-$(CONFIG_STAGING) += staging/
obj-y += platform/
obj-$(CONFIG_MAILBOX) += mailbox/
obj-$(CONFIG_HWSPINLOCK) += hwspinlock/
obj-$(CONFIG_REMOTEPROC) += remoteproc/
obj-$(CONFIG_RPMSG) += rpmsg/
obj-$(CONFIG_SOUNDWIRE) += soundwire/
# Virtualization drivers
obj-$(CONFIG_VIRT_DRIVERS) += virt/
obj-$(subst m,y,$(CONFIG_HYPERV)) += hv/
obj-$(CONFIG_PM_DEVFREQ) += devfreq/
obj-$(CONFIG_EXTCON) += extcon/
obj-$(CONFIG_MEMORY) += memory/
obj-$(CONFIG_IIO) += iio/
obj-$(CONFIG_VME_BUS) += vme/
obj-$(CONFIG_IPACK_BUS) += ipack/
obj-$(CONFIG_NTB) += ntb/
obj-$(CONFIG_POWERCAP) += powercap/
obj-$(CONFIG_MCB) += mcb/
obj-$(CONFIG_PERF_EVENTS) += perf/
obj-$(CONFIG_RAS) += ras/
obj-$(CONFIG_USB4) += thunderbolt/
obj-$(CONFIG_CORESIGHT) += hwtracing/coresight/
obj-y += hwtracing/intel_th/
obj-$(CONFIG_STM) += hwtracing/stm/
obj-$(CONFIG_ANDROID) += android/
obj-$(CONFIG_NVMEM) += nvmem/
obj-$(CONFIG_FPGA) += fpga/
obj-$(CONFIG_FSI) += fsi/
obj-$(CONFIG_TEE) += tee/
obj-$(CONFIG_MULTIPLEXER) += mux/
obj-$(CONFIG_UNISYS_VISORBUS) += visorbus/
obj-$(CONFIG_SIOX) += siox/
obj-$(CONFIG_GNSS) += gnss/
obj-$(CONFIG_INTERCONNECT) += interconnect/
obj-$(CONFIG_COUNTER) += counter/
obj-$(CONFIG_MOST) += most/