linux-stable/drivers/iio/accel/fxls8962af-core.c
Greg Kroah-Hartman 6bce28cb49 First set of IIO new device and feature support for the 5.16 cycle
Counter subsystem changes now sent separately.
 
 This has been a busy cycle, so lots here and a few more stragglers to
 come next week.
 
 Big new feature in this cycle is probably output buffer support.
 This has been in the works for a very long time so it's great to see
 Mihail pick up the challenge and build upon his predecessors work to finally
 bring this feature to mainline.
 
 New device support
 ------------------
 
 * adi,adxl313
   - New driver and dt bindings for this low power accelerometer.
 * adi,adxl355
   - New driver and dt bindings for this accelerometer.
   - Later series adds buffer support.
 * asahi-kasei,ak8975
   - Minor additions to driver to support ak09916
 * aspeed,aspeed-adc
   - Substantial rework plus feature additions to add support for the
     ast2600 including a new dt bindings doc.
 * atmel,at91_sama5d2
   - Rework and support introduced for the sama7g5 parts.
 * maxim,max31865
   - New driver and bindings for this RTD temperature sensor chip.
 * nxp,imx8qxp
   - New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
 * senseair,sunrise
   - New driver and bindings for this family of carbon dioxide gas sensors.
 * sensiron,scd4x
   - New driver and bindings for this carbon dioxide gas sensor.
 
 New features
 ------------
 
 * Output buffer support.  Works in a similar fashion to input buffers, but
   in this case userspace pushes data into the kfifo which is then drained
   to the device when a trigger occurs.  Support added to the ad5766 DAC
   driver.
 * Core, devm_iio_map_array_register() to avoid need for
   devm_add_action_or_reset() based cleanup in fully managed allocation
   drivers.
 * Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
   few drivers where it really hard to ensure the correct data alignment in
   an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
   buffer so should be avoided whenever possible.  Used in the ti,adc108s102,
   invense,mpu3050 and adi,adis16400.  This closes the last   known set
   of drivers with alignment issues at this interface.
 * maxim,max1027
   - Substantial rework to this driver main target of which was supporting
     use of other triggers than it's own EOC interrupt.
   - Transfer optimization.
 * nxp,fxls8962af
   - Threshold even support including using it as a wakeup source.
 
 Cleanups, minor fixes etc
 -------------------------
 
 Chances of a common type to multiple drivers:
 
 * devm_ conversion and drop of .remove() callbacks in:
   - adi,ad5064
   - adi,ad7291
   - adi,ad7303
   - adi,ad7746
   - adi,ad9832
   - adi,adis16080
   - dialog,da9150-gpadc
   - intel,mrfld_adc
   - marvell,berlin2
   - maxim,max1363
   - maxim,max44000
   - nuvoton,nau7802
   - st_sensors (includes a lot of rework!)
   - ti,ads8344
   - ti,lp8788
 
 * devm_platform_ioremap_resource() used to reduce boilerplate
   - cirrus,ep93xx
   - rockchip,saradc
   - stm,stm32-dac
 
 * Use dev_err_probe() in more places to both not print on deferred probe and
   ensure a reason for the deferral is available for debug purposes.
   - adi,ad8801
   - capella,cm36651
   - linear,ltc1660
   - maxim,ds4424
   - maxim,max5821
   - microchip,mcp4922
   - nxp,lpc18xx
   - onnn,noa1305
   - st,lsm9ds0
   - st,st_sensors
   - st,stm32-dac
   - ti,afe4403
   - ti,afe4404
   - ti,dac7311
 
 * Drop error returns in SPI and I2C remove() functions as they are ignored and
   long term plan is to change these all over to returning void. In some cases
   these patches just make it 'obvious' they always return 0 where it was the
   case before but not easy to tell.
   - adi,ad5380
   - adi,ad5446
   - adi,ad5686
   - adi,ad5592r
   - bosch,bma400
   - bosch,bmc150
   - fsl,mma7455
   - honeywell,hmc5843
   - kionix,kxsd9
   - maxim,max5487
   - meas,ms5611
   - ti,afe4403
 
 Driver specific changes
 
 * adi,ad5770r
   - Bring driver inline with documented bindings.
 * adi,ad7746
   - Trivial style fix
 * adi,ad7949
   - Express some magic values as the underlying parts via new #defines.
   - Make it work with SPI controllers that don't support 14 or 16 bit messages
   - Support selection of voltage reference from dt including expanding the
     dt-bindings to cover this new functionality.
 * adi,ad799x
   - Implement selection of external reference voltage on AD7991, AD7995 and
     AD7999.
   - Add missing dt-bindings doc for devices supported by this driver.
 * adi,adislib
   - Move interrupt startup to better location in startup flow.
   - Handle devices that cannot mask/unmask the drdy pin and must instead mask
     at the interrupt controller.  Applies to the adis16460 and adis16475 from
     which we then drop equivalent code.
 * adi,ltc2983
   - Add support for optional reset pin.
   - Fail to probe if no channels specified in dt binding.
 * asahi-kasei,ak8975
   - dt-binding additions of missing vid-supply regulator.
 * aspeed,aspeed-adc
   - Typo fix.
 * fsl,mma7660
   - Mark acpi_device_id table __maybe_unused to avoid build warning.
 * fsl,imx25-gcq
   - Avoid initializing regulators that aren't used.
 * invensense,mpu3050
   - Drop a dead protection against a clash with the old input driver.
 * invensense,mpu6050
   - Rework code to not use strcpy() and hence avoid possibility of wrong sized
     buffers. Note this wasn't a bug, but the new code is a lot more readable.
   - Mark acpi_device_id table __maybe_unused to avoid build warning.
 * kionix,kxcjk1013
   - dt-binding addition to note it supports interrupts.
 * marvell,berlin2-adc
   - Enable COMPILE_TEST building.
 * maxim,max1027
   - Avoid returning success in an error path.
 * nxp,imx8qxp
   - Fix warning when runtime pm not enabled via __maybe_unused.
 * ricoh,rn5t618
   - Use the new devm_iio_map_array_register() instead of open coding the same.
 * samsung,exynos_adc
   - Improve kconfig help text.
 * st,lsm6dsx
   - Move max_fifo_size into the fifo_ops structure where the other configuration
     parameters are found.
 * st,st_sensors:
   - Reorder to ensure we turn the power off after removing userspace interfaces.
 * senseair,sunrise
   - Add missing I2C dependency.
 * ti,twl6030
   - Small code tidy up.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmFudVERHGppYzIzQGtl
 cm5lbC5vcmcACgkQVIU0mcT0Foiepg//R5DRm1gMFGP/dl2P8u6KD2oXNmbqc3J0
 +EPRTkyTyawQzc21wdxUh3oObgxmDS6P7Cr17z9viGse2PsUjza4Sptic3Zqi3Kv
 FzeXZaP0GY9nC+hAyz+dSkMKNw19mkCYYEIWhDwYFpXMiOV8QlT+6pFgOiffofeR
 GYMUoV2XeuxR6OH0zMOuYKTzjOCYC+VJTP4BfeUetpRZQyllgFOA+5KX4ZWTiJMV
 eGCaq3Hhn6IQa7ATgYUBYJyMkAXQDrKDaMxiaCIuh/k3bgjAkfhkV48mu2cHTsX9
 v0q21JkgmBenwNP/OQ6mxmWR9SFY4eB22Ptkd1foTPjAsqoST7qmqEBhhLrRb/fB
 HkL0I7M4tWDqSTJKgdn+UHYrKFW9oBHIt5SK1tCS+zTYIn1wEmkY/w/9MuZllBFO
 VKu5q2ypf/yGgCqPIZilK69mrZd7/72rE6tr3oefUF2iUVLdh9fI1TjGGyoT6GZ5
 ZlEIfGHRpcRGHFiA4e+6tTx9VLr8m1B5YVvBWWPlruYe8ep7MmD3KjUcwINiRyNs
 5rdBl2RI8VAUBbQ+60VWn03e/0kuRESpFC3Gf/ng+6hRSUbRFe4lZw60GbyFDXwV
 m1odTlkXA7l6oRG9f5COhE/oNO7dsfMO74W6+yzhWICnxjgJFosaaZTLw8F9QJdS
 m3z9tSU84js=
 =htmG
 -----END PGP SIGNATURE-----

Merge tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next

Jonathan writes:

First set of IIO new device and feature support for the 5.16 cycle

Counter subsystem changes now sent separately.

This has been a busy cycle, so lots here and a few more stragglers to
come next week.

Big new feature in this cycle is probably output buffer support.
This has been in the works for a very long time so it's great to see
Mihail pick up the challenge and build upon his predecessors work to finally
bring this feature to mainline.

New device support
------------------

* adi,adxl313
  - New driver and dt bindings for this low power accelerometer.
* adi,adxl355
  - New driver and dt bindings for this accelerometer.
  - Later series adds buffer support.
* asahi-kasei,ak8975
  - Minor additions to driver to support ak09916
* aspeed,aspeed-adc
  - Substantial rework plus feature additions to add support for the
    ast2600 including a new dt bindings doc.
* atmel,at91_sama5d2
  - Rework and support introduced for the sama7g5 parts.
* maxim,max31865
  - New driver and bindings for this RTD temperature sensor chip.
* nxp,imx8qxp
  - New driver and bindings for the ADC found on the i.MX 8QuadXPlus Soc.
* senseair,sunrise
  - New driver and bindings for this family of carbon dioxide gas sensors.
* sensiron,scd4x
  - New driver and bindings for this carbon dioxide gas sensor.

New features
------------

* Output buffer support.  Works in a similar fashion to input buffers, but
  in this case userspace pushes data into the kfifo which is then drained
  to the device when a trigger occurs.  Support added to the ad5766 DAC
  driver.
* Core, devm_iio_map_array_register() to avoid need for
  devm_add_action_or_reset() based cleanup in fully managed allocation
  drivers.
* Core iio_push_to_buffers_with_ts_unaligned() function to safely handle a
  few drivers where it really hard to ensure the correct data alignment in
  an iio_push_to_buffers_with_timestamp() call. Note this uses a bounce
  buffer so should be avoided whenever possible.  Used in the ti,adc108s102,
  invense,mpu3050 and adi,adis16400.  This closes the last   known set
  of drivers with alignment issues at this interface.
* maxim,max1027
  - Substantial rework to this driver main target of which was supporting
    use of other triggers than it's own EOC interrupt.
  - Transfer optimization.
* nxp,fxls8962af
  - Threshold even support including using it as a wakeup source.

Cleanups, minor fixes etc
-------------------------

Chances of a common type to multiple drivers:

* devm_ conversion and drop of .remove() callbacks in:
  - adi,ad5064
  - adi,ad7291
  - adi,ad7303
  - adi,ad7746
  - adi,ad9832
  - adi,adis16080
  - dialog,da9150-gpadc
  - intel,mrfld_adc
  - marvell,berlin2
  - maxim,max1363
  - maxim,max44000
  - nuvoton,nau7802
  - st_sensors (includes a lot of rework!)
  - ti,ads8344
  - ti,lp8788

* devm_platform_ioremap_resource() used to reduce boilerplate
  - cirrus,ep93xx
  - rockchip,saradc
  - stm,stm32-dac

* Use dev_err_probe() in more places to both not print on deferred probe and
  ensure a reason for the deferral is available for debug purposes.
  - adi,ad8801
  - capella,cm36651
  - linear,ltc1660
  - maxim,ds4424
  - maxim,max5821
  - microchip,mcp4922
  - nxp,lpc18xx
  - onnn,noa1305
  - st,lsm9ds0
  - st,st_sensors
  - st,stm32-dac
  - ti,afe4403
  - ti,afe4404
  - ti,dac7311

* Drop error returns in SPI and I2C remove() functions as they are ignored and
  long term plan is to change these all over to returning void. In some cases
  these patches just make it 'obvious' they always return 0 where it was the
  case before but not easy to tell.
  - adi,ad5380
  - adi,ad5446
  - adi,ad5686
  - adi,ad5592r
  - bosch,bma400
  - bosch,bmc150
  - fsl,mma7455
  - honeywell,hmc5843
  - kionix,kxsd9
  - maxim,max5487
  - meas,ms5611
  - ti,afe4403

Driver specific changes

* adi,ad5770r
  - Bring driver inline with documented bindings.
* adi,ad7746
  - Trivial style fix
* adi,ad7949
  - Express some magic values as the underlying parts via new #defines.
  - Make it work with SPI controllers that don't support 14 or 16 bit messages
  - Support selection of voltage reference from dt including expanding the
    dt-bindings to cover this new functionality.
* adi,ad799x
  - Implement selection of external reference voltage on AD7991, AD7995 and
    AD7999.
  - Add missing dt-bindings doc for devices supported by this driver.
* adi,adislib
  - Move interrupt startup to better location in startup flow.
  - Handle devices that cannot mask/unmask the drdy pin and must instead mask
    at the interrupt controller.  Applies to the adis16460 and adis16475 from
    which we then drop equivalent code.
* adi,ltc2983
  - Add support for optional reset pin.
  - Fail to probe if no channels specified in dt binding.
* asahi-kasei,ak8975
  - dt-binding additions of missing vid-supply regulator.
* aspeed,aspeed-adc
  - Typo fix.
* fsl,mma7660
  - Mark acpi_device_id table __maybe_unused to avoid build warning.
* fsl,imx25-gcq
  - Avoid initializing regulators that aren't used.
* invensense,mpu3050
  - Drop a dead protection against a clash with the old input driver.
* invensense,mpu6050
  - Rework code to not use strcpy() and hence avoid possibility of wrong sized
    buffers. Note this wasn't a bug, but the new code is a lot more readable.
  - Mark acpi_device_id table __maybe_unused to avoid build warning.
* kionix,kxcjk1013
  - dt-binding addition to note it supports interrupts.
* marvell,berlin2-adc
  - Enable COMPILE_TEST building.
* maxim,max1027
  - Avoid returning success in an error path.
* nxp,imx8qxp
  - Fix warning when runtime pm not enabled via __maybe_unused.
* ricoh,rn5t618
  - Use the new devm_iio_map_array_register() instead of open coding the same.
* samsung,exynos_adc
  - Improve kconfig help text.
* st,lsm6dsx
  - Move max_fifo_size into the fifo_ops structure where the other configuration
    parameters are found.
* st,st_sensors:
  - Reorder to ensure we turn the power off after removing userspace interfaces.
* senseair,sunrise
  - Add missing I2C dependency.
* ti,twl6030
  - Small code tidy up.

* tag 'iio-for-5.16a-split-take4' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (148 commits)
  iio: imx8qxp-adc: mark PM functions as __maybe_unused
  iio: pressure: ms5611: Make ms5611_remove() return void
  iio: potentiometer: max5487: Don't return an error in .remove()
  iio: magn: hmc5843: Make hmc5843_common_remove() return void
  iio: health: afe4403: Don't return an error in .remove()
  iio: dac: ad5686: Make ad5686_remove() return void
  iio: dac: ad5592r: Make ad5592r_remove() return void
  iio: dac: ad5446: Make ad5446_remove() return void
  iio: dac: ad5380: Make ad5380_remove() return void
  iio: accel: mma7455: Make mma7455_core_remove() return void
  iio: accel: kxsd9: Make kxsd9_common_remove() return void
  iio: accel: bmi088: Make bmi088_accel_core_remove() return void
  iio: accel: bmc150: Make bmc150_accel_core_remove() return void
  iio: accel: bma400: Make bma400_remove() return void
  drivers:iio:dac:ad5766.c: Add trigger buffer
  iio: triggered-buffer: extend support to configure output buffers
  iio: kfifo-buffer: Add output buffer support
  iio: Add output buffer support
  iio: documentation: Document scd4x calibration use
  drivers: iio: chemical: Add support for Sensirion SCD4x CO2 sensor
  ...
2021-10-19 11:44:28 +02:00

1305 lines
32 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

// SPDX-License-Identifier: GPL-2.0
/*
* NXP FXLS8962AF/FXLS8964AF Accelerometer Core Driver
*
* Copyright 2021 Connected Cars A/S
*
* Datasheet:
* https://www.nxp.com/docs/en/data-sheet/FXLS8962AF.pdf
* https://www.nxp.com/docs/en/data-sheet/FXLS8964AF.pdf
*
* Errata:
* https://www.nxp.com/docs/en/errata/ES_FXLS8962AF.pdf
*/
#include <linux/bits.h>
#include <linux/bitfield.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/of_irq.h>
#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
#include <linux/regmap.h>
#include <linux/iio/buffer.h>
#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/iio/kfifo_buf.h>
#include <linux/iio/sysfs.h>
#include "fxls8962af.h"
#define FXLS8962AF_INT_STATUS 0x00
#define FXLS8962AF_INT_STATUS_SRC_BOOT BIT(0)
#define FXLS8962AF_INT_STATUS_SRC_SDCD_OT BIT(4)
#define FXLS8962AF_INT_STATUS_SRC_BUF BIT(5)
#define FXLS8962AF_INT_STATUS_SRC_DRDY BIT(7)
#define FXLS8962AF_TEMP_OUT 0x01
#define FXLS8962AF_VECM_LSB 0x02
#define FXLS8962AF_OUT_X_LSB 0x04
#define FXLS8962AF_OUT_Y_LSB 0x06
#define FXLS8962AF_OUT_Z_LSB 0x08
#define FXLS8962AF_BUF_STATUS 0x0b
#define FXLS8962AF_BUF_STATUS_BUF_CNT GENMASK(5, 0)
#define FXLS8962AF_BUF_STATUS_BUF_OVF BIT(6)
#define FXLS8962AF_BUF_STATUS_BUF_WMRK BIT(7)
#define FXLS8962AF_BUF_X_LSB 0x0c
#define FXLS8962AF_BUF_Y_LSB 0x0e
#define FXLS8962AF_BUF_Z_LSB 0x10
#define FXLS8962AF_PROD_REV 0x12
#define FXLS8962AF_WHO_AM_I 0x13
#define FXLS8962AF_SYS_MODE 0x14
#define FXLS8962AF_SENS_CONFIG1 0x15
#define FXLS8962AF_SENS_CONFIG1_ACTIVE BIT(0)
#define FXLS8962AF_SENS_CONFIG1_RST BIT(7)
#define FXLS8962AF_SC1_FSR_MASK GENMASK(2, 1)
#define FXLS8962AF_SC1_FSR_PREP(x) FIELD_PREP(FXLS8962AF_SC1_FSR_MASK, (x))
#define FXLS8962AF_SC1_FSR_GET(x) FIELD_GET(FXLS8962AF_SC1_FSR_MASK, (x))
#define FXLS8962AF_SENS_CONFIG2 0x16
#define FXLS8962AF_SENS_CONFIG3 0x17
#define FXLS8962AF_SC3_WAKE_ODR_MASK GENMASK(7, 4)
#define FXLS8962AF_SC3_WAKE_ODR_PREP(x) FIELD_PREP(FXLS8962AF_SC3_WAKE_ODR_MASK, (x))
#define FXLS8962AF_SC3_WAKE_ODR_GET(x) FIELD_GET(FXLS8962AF_SC3_WAKE_ODR_MASK, (x))
#define FXLS8962AF_SENS_CONFIG4 0x18
#define FXLS8962AF_SC4_INT_PP_OD_MASK BIT(1)
#define FXLS8962AF_SC4_INT_PP_OD_PREP(x) FIELD_PREP(FXLS8962AF_SC4_INT_PP_OD_MASK, (x))
#define FXLS8962AF_SC4_INT_POL_MASK BIT(0)
#define FXLS8962AF_SC4_INT_POL_PREP(x) FIELD_PREP(FXLS8962AF_SC4_INT_POL_MASK, (x))
#define FXLS8962AF_SENS_CONFIG5 0x19
#define FXLS8962AF_WAKE_IDLE_LSB 0x1b
#define FXLS8962AF_SLEEP_IDLE_LSB 0x1c
#define FXLS8962AF_ASLP_COUNT_LSB 0x1e
#define FXLS8962AF_INT_EN 0x20
#define FXLS8962AF_INT_EN_SDCD_OT_EN BIT(5)
#define FXLS8962AF_INT_EN_BUF_EN BIT(6)
#define FXLS8962AF_INT_PIN_SEL 0x21
#define FXLS8962AF_INT_PIN_SEL_MASK GENMASK(7, 0)
#define FXLS8962AF_INT_PIN_SEL_INT1 0x00
#define FXLS8962AF_INT_PIN_SEL_INT2 GENMASK(7, 0)
#define FXLS8962AF_OFF_X 0x22
#define FXLS8962AF_OFF_Y 0x23
#define FXLS8962AF_OFF_Z 0x24
#define FXLS8962AF_BUF_CONFIG1 0x26
#define FXLS8962AF_BC1_BUF_MODE_MASK GENMASK(6, 5)
#define FXLS8962AF_BC1_BUF_MODE_PREP(x) FIELD_PREP(FXLS8962AF_BC1_BUF_MODE_MASK, (x))
#define FXLS8962AF_BUF_CONFIG2 0x27
#define FXLS8962AF_BUF_CONFIG2_BUF_WMRK GENMASK(5, 0)
#define FXLS8962AF_ORIENT_STATUS 0x28
#define FXLS8962AF_ORIENT_CONFIG 0x29
#define FXLS8962AF_ORIENT_DBCOUNT 0x2a
#define FXLS8962AF_ORIENT_BF_ZCOMP 0x2b
#define FXLS8962AF_ORIENT_THS_REG 0x2c
#define FXLS8962AF_SDCD_INT_SRC1 0x2d
#define FXLS8962AF_SDCD_INT_SRC1_X_OT BIT(5)
#define FXLS8962AF_SDCD_INT_SRC1_X_POL BIT(4)
#define FXLS8962AF_SDCD_INT_SRC1_Y_OT BIT(3)
#define FXLS8962AF_SDCD_INT_SRC1_Y_POL BIT(2)
#define FXLS8962AF_SDCD_INT_SRC1_Z_OT BIT(1)
#define FXLS8962AF_SDCD_INT_SRC1_Z_POL BIT(0)
#define FXLS8962AF_SDCD_INT_SRC2 0x2e
#define FXLS8962AF_SDCD_CONFIG1 0x2f
#define FXLS8962AF_SDCD_CONFIG1_Z_OT_EN BIT(3)
#define FXLS8962AF_SDCD_CONFIG1_Y_OT_EN BIT(4)
#define FXLS8962AF_SDCD_CONFIG1_X_OT_EN BIT(5)
#define FXLS8962AF_SDCD_CONFIG1_OT_ELE BIT(7)
#define FXLS8962AF_SDCD_CONFIG2 0x30
#define FXLS8962AF_SDCD_CONFIG2_SDCD_EN BIT(7)
#define FXLS8962AF_SC2_REF_UPDM_AC GENMASK(6, 5)
#define FXLS8962AF_SDCD_OT_DBCNT 0x31
#define FXLS8962AF_SDCD_WT_DBCNT 0x32
#define FXLS8962AF_SDCD_LTHS_LSB 0x33
#define FXLS8962AF_SDCD_UTHS_LSB 0x35
#define FXLS8962AF_SELF_TEST_CONFIG1 0x37
#define FXLS8962AF_SELF_TEST_CONFIG2 0x38
#define FXLS8962AF_MAX_REG 0x38
#define FXLS8962AF_DEVICE_ID 0x62
#define FXLS8964AF_DEVICE_ID 0x84
/* Raw temp channel offset */
#define FXLS8962AF_TEMP_CENTER_VAL 25
#define FXLS8962AF_AUTO_SUSPEND_DELAY_MS 2000
#define FXLS8962AF_FIFO_LENGTH 32
#define FXLS8962AF_SCALE_TABLE_LEN 4
#define FXLS8962AF_SAMP_FREQ_TABLE_LEN 13
static const int fxls8962af_scale_table[FXLS8962AF_SCALE_TABLE_LEN][2] = {
{0, IIO_G_TO_M_S_2(980000)},
{0, IIO_G_TO_M_S_2(1950000)},
{0, IIO_G_TO_M_S_2(3910000)},
{0, IIO_G_TO_M_S_2(7810000)},
};
static const int fxls8962af_samp_freq_table[FXLS8962AF_SAMP_FREQ_TABLE_LEN][2] = {
{3200, 0}, {1600, 0}, {800, 0}, {400, 0}, {200, 0}, {100, 0},
{50, 0}, {25, 0}, {12, 500000}, {6, 250000}, {3, 125000},
{1, 563000}, {0, 781000},
};
struct fxls8962af_chip_info {
const char *name;
const struct iio_chan_spec *channels;
int num_channels;
u8 chip_id;
};
struct fxls8962af_data {
struct regmap *regmap;
const struct fxls8962af_chip_info *chip_info;
struct regulator *vdd_reg;
struct {
__le16 channels[3];
s64 ts __aligned(8);
} scan;
int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
struct iio_mount_matrix orientation;
int irq;
u8 watermark;
u8 enable_event;
u16 lower_thres;
u16 upper_thres;
};
const struct regmap_config fxls8962af_regmap_conf = {
.reg_bits = 8,
.val_bits = 8,
.max_register = FXLS8962AF_MAX_REG,
};
EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
enum {
fxls8962af_idx_x,
fxls8962af_idx_y,
fxls8962af_idx_z,
fxls8962af_idx_ts,
};
enum fxls8962af_int_pin {
FXLS8962AF_PIN_INT1,
FXLS8962AF_PIN_INT2,
};
static int fxls8962af_power_on(struct fxls8962af_data *data)
{
struct device *dev = regmap_get_device(data->regmap);
int ret;
ret = pm_runtime_resume_and_get(dev);
if (ret)
dev_err(dev, "failed to power on\n");
return ret;
}
static int fxls8962af_power_off(struct fxls8962af_data *data)
{
struct device *dev = regmap_get_device(data->regmap);
int ret;
pm_runtime_mark_last_busy(dev);
ret = pm_runtime_put_autosuspend(dev);
if (ret)
dev_err(dev, "failed to power off\n");
return ret;
}
static int fxls8962af_standby(struct fxls8962af_data *data)
{
return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
FXLS8962AF_SENS_CONFIG1_ACTIVE, 0);
}
static int fxls8962af_active(struct fxls8962af_data *data)
{
return regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
FXLS8962AF_SENS_CONFIG1_ACTIVE, 1);
}
static int fxls8962af_is_active(struct fxls8962af_data *data)
{
unsigned int reg;
int ret;
ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
if (ret)
return ret;
return reg & FXLS8962AF_SENS_CONFIG1_ACTIVE;
}
static int fxls8962af_get_out(struct fxls8962af_data *data,
struct iio_chan_spec const *chan, int *val)
{
struct device *dev = regmap_get_device(data->regmap);
__le16 raw_val;
int is_active;
int ret;
is_active = fxls8962af_is_active(data);
if (!is_active) {
ret = fxls8962af_power_on(data);
if (ret)
return ret;
}
ret = regmap_bulk_read(data->regmap, chan->address,
&raw_val, sizeof(data->lower_thres));
if (!is_active)
fxls8962af_power_off(data);
if (ret) {
dev_err(dev, "failed to get out reg 0x%lx\n", chan->address);
return ret;
}
*val = sign_extend32(le16_to_cpu(raw_val),
chan->scan_type.realbits - 1);
return IIO_VAL_INT;
}
static int fxls8962af_read_avail(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
const int **vals, int *type, int *length,
long mask)
{
switch (mask) {
case IIO_CHAN_INFO_SCALE:
*type = IIO_VAL_INT_PLUS_NANO;
*vals = (int *)fxls8962af_scale_table;
*length = ARRAY_SIZE(fxls8962af_scale_table) * 2;
return IIO_AVAIL_LIST;
case IIO_CHAN_INFO_SAMP_FREQ:
*type = IIO_VAL_INT_PLUS_MICRO;
*vals = (int *)fxls8962af_samp_freq_table;
*length = ARRAY_SIZE(fxls8962af_samp_freq_table) * 2;
return IIO_AVAIL_LIST;
default:
return -EINVAL;
}
}
static int fxls8962af_write_raw_get_fmt(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
long mask)
{
switch (mask) {
case IIO_CHAN_INFO_SCALE:
return IIO_VAL_INT_PLUS_NANO;
case IIO_CHAN_INFO_SAMP_FREQ:
return IIO_VAL_INT_PLUS_MICRO;
default:
return IIO_VAL_INT_PLUS_NANO;
}
}
static int fxls8962af_update_config(struct fxls8962af_data *data, u8 reg,
u8 mask, u8 val)
{
int ret;
int is_active;
is_active = fxls8962af_is_active(data);
if (is_active) {
ret = fxls8962af_standby(data);
if (ret)
return ret;
}
ret = regmap_update_bits(data->regmap, reg, mask, val);
if (ret)
return ret;
if (is_active) {
ret = fxls8962af_active(data);
if (ret)
return ret;
}
return 0;
}
static int fxls8962af_set_full_scale(struct fxls8962af_data *data, u32 scale)
{
int i;
for (i = 0; i < ARRAY_SIZE(fxls8962af_scale_table); i++)
if (scale == fxls8962af_scale_table[i][1])
break;
if (i == ARRAY_SIZE(fxls8962af_scale_table))
return -EINVAL;
return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG1,
FXLS8962AF_SC1_FSR_MASK,
FXLS8962AF_SC1_FSR_PREP(i));
}
static unsigned int fxls8962af_read_full_scale(struct fxls8962af_data *data,
int *val)
{
int ret;
unsigned int reg;
u8 range_idx;
ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG1, &reg);
if (ret)
return ret;
range_idx = FXLS8962AF_SC1_FSR_GET(reg);
*val = fxls8962af_scale_table[range_idx][1];
return IIO_VAL_INT_PLUS_NANO;
}
static int fxls8962af_set_samp_freq(struct fxls8962af_data *data, u32 val,
u32 val2)
{
int i;
for (i = 0; i < ARRAY_SIZE(fxls8962af_samp_freq_table); i++)
if (val == fxls8962af_samp_freq_table[i][0] &&
val2 == fxls8962af_samp_freq_table[i][1])
break;
if (i == ARRAY_SIZE(fxls8962af_samp_freq_table))
return -EINVAL;
return fxls8962af_update_config(data, FXLS8962AF_SENS_CONFIG3,
FXLS8962AF_SC3_WAKE_ODR_MASK,
FXLS8962AF_SC3_WAKE_ODR_PREP(i));
}
static unsigned int fxls8962af_read_samp_freq(struct fxls8962af_data *data,
int *val, int *val2)
{
int ret;
unsigned int reg;
u8 range_idx;
ret = regmap_read(data->regmap, FXLS8962AF_SENS_CONFIG3, &reg);
if (ret)
return ret;
range_idx = FXLS8962AF_SC3_WAKE_ODR_GET(reg);
*val = fxls8962af_samp_freq_table[range_idx][0];
*val2 = fxls8962af_samp_freq_table[range_idx][1];
return IIO_VAL_INT_PLUS_MICRO;
}
static int fxls8962af_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int *val, int *val2, long mask)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
switch (mask) {
case IIO_CHAN_INFO_RAW:
switch (chan->type) {
case IIO_TEMP:
case IIO_ACCEL:
return fxls8962af_get_out(data, chan, val);
default:
return -EINVAL;
}
case IIO_CHAN_INFO_OFFSET:
if (chan->type != IIO_TEMP)
return -EINVAL;
*val = FXLS8962AF_TEMP_CENTER_VAL;
return IIO_VAL_INT;
case IIO_CHAN_INFO_SCALE:
*val = 0;
return fxls8962af_read_full_scale(data, val2);
case IIO_CHAN_INFO_SAMP_FREQ:
return fxls8962af_read_samp_freq(data, val, val2);
default:
return -EINVAL;
}
}
static int fxls8962af_write_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int val, int val2, long mask)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
int ret;
switch (mask) {
case IIO_CHAN_INFO_SCALE:
if (val != 0)
return -EINVAL;
ret = iio_device_claim_direct_mode(indio_dev);
if (ret)
return ret;
ret = fxls8962af_set_full_scale(data, val2);
iio_device_release_direct_mode(indio_dev);
return ret;
case IIO_CHAN_INFO_SAMP_FREQ:
ret = iio_device_claim_direct_mode(indio_dev);
if (ret)
return ret;
ret = fxls8962af_set_samp_freq(data, val, val2);
iio_device_release_direct_mode(indio_dev);
return ret;
default:
return -EINVAL;
}
}
static int fxls8962af_event_setup(struct fxls8962af_data *data, int state)
{
/* Enable wakeup interrupt */
int mask = FXLS8962AF_INT_EN_SDCD_OT_EN;
int value = state ? mask : 0;
return regmap_update_bits(data->regmap, FXLS8962AF_INT_EN, mask, value);
}
static int fxls8962af_set_watermark(struct iio_dev *indio_dev, unsigned val)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
if (val > FXLS8962AF_FIFO_LENGTH)
val = FXLS8962AF_FIFO_LENGTH;
data->watermark = val;
return 0;
}
static int __fxls8962af_set_thresholds(struct fxls8962af_data *data,
const struct iio_chan_spec *chan,
enum iio_event_direction dir,
int val)
{
switch (dir) {
case IIO_EV_DIR_FALLING:
data->lower_thres = val;
return regmap_bulk_write(data->regmap, FXLS8962AF_SDCD_LTHS_LSB,
&data->lower_thres, sizeof(data->lower_thres));
case IIO_EV_DIR_RISING:
data->upper_thres = val;
return regmap_bulk_write(data->regmap, FXLS8962AF_SDCD_UTHS_LSB,
&data->upper_thres, sizeof(data->upper_thres));
default:
return -EINVAL;
}
}
static int fxls8962af_read_event(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir,
enum iio_event_info info,
int *val, int *val2)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
int ret;
if (type != IIO_EV_TYPE_THRESH)
return -EINVAL;
switch (dir) {
case IIO_EV_DIR_FALLING:
ret = regmap_bulk_read(data->regmap, FXLS8962AF_SDCD_LTHS_LSB,
&data->lower_thres, sizeof(data->lower_thres));
if (ret)
return ret;
*val = sign_extend32(data->lower_thres, chan->scan_type.realbits - 1);
return IIO_VAL_INT;
case IIO_EV_DIR_RISING:
ret = regmap_bulk_read(data->regmap, FXLS8962AF_SDCD_UTHS_LSB,
&data->upper_thres, sizeof(data->upper_thres));
if (ret)
return ret;
*val = sign_extend32(data->upper_thres, chan->scan_type.realbits - 1);
return IIO_VAL_INT;
default:
return -EINVAL;
}
}
static int fxls8962af_write_event(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir,
enum iio_event_info info,
int val, int val2)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
int ret, val_masked;
if (type != IIO_EV_TYPE_THRESH)
return -EINVAL;
if (val < -2048 || val > 2047)
return -EINVAL;
if (data->enable_event)
return -EBUSY;
val_masked = val & GENMASK(11, 0);
if (fxls8962af_is_active(data)) {
ret = fxls8962af_standby(data);
if (ret)
return ret;
ret = __fxls8962af_set_thresholds(data, chan, dir, val_masked);
if (ret)
return ret;
return fxls8962af_active(data);
} else {
return __fxls8962af_set_thresholds(data, chan, dir, val_masked);
}
}
static int
fxls8962af_read_event_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
if (type != IIO_EV_TYPE_THRESH)
return -EINVAL;
switch (chan->channel2) {
case IIO_MOD_X:
return !!(FXLS8962AF_SDCD_CONFIG1_X_OT_EN & data->enable_event);
case IIO_MOD_Y:
return !!(FXLS8962AF_SDCD_CONFIG1_Y_OT_EN & data->enable_event);
case IIO_MOD_Z:
return !!(FXLS8962AF_SDCD_CONFIG1_Z_OT_EN & data->enable_event);
default:
return -EINVAL;
}
}
static int
fxls8962af_write_event_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir, int state)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
u8 enable_event, enable_bits;
int ret, value;
if (type != IIO_EV_TYPE_THRESH)
return -EINVAL;
switch (chan->channel2) {
case IIO_MOD_X:
enable_bits = FXLS8962AF_SDCD_CONFIG1_X_OT_EN;
break;
case IIO_MOD_Y:
enable_bits = FXLS8962AF_SDCD_CONFIG1_Y_OT_EN;
break;
case IIO_MOD_Z:
enable_bits = FXLS8962AF_SDCD_CONFIG1_Z_OT_EN;
break;
default:
return -EINVAL;
}
if (state)
enable_event = data->enable_event | enable_bits;
else
enable_event = data->enable_event & ~enable_bits;
if (data->enable_event == enable_event)
return 0;
ret = fxls8962af_standby(data);
if (ret)
return ret;
/* Enable events */
value = enable_event | FXLS8962AF_SDCD_CONFIG1_OT_ELE;
ret = regmap_write(data->regmap, FXLS8962AF_SDCD_CONFIG1, value);
if (ret)
return ret;
/*
* Enable update of SDCD_REF_X/Y/Z values with the current decimated and
* trimmed X/Y/Z acceleration input data. This allows for acceleration
* slope detection with Data(n) to Data(n1) always used as the input
* to the window comparator.
*/
value = enable_event ?
FXLS8962AF_SDCD_CONFIG2_SDCD_EN | FXLS8962AF_SC2_REF_UPDM_AC :
0x00;
ret = regmap_write(data->regmap, FXLS8962AF_SDCD_CONFIG2, value);
if (ret)
return ret;
ret = fxls8962af_event_setup(data, state);
if (ret)
return ret;
data->enable_event = enable_event;
if (data->enable_event) {
fxls8962af_active(data);
ret = fxls8962af_power_on(data);
} else {
ret = iio_device_claim_direct_mode(indio_dev);
if (ret)
return ret;
/* Not in buffered mode so disable power */
ret = fxls8962af_power_off(data);
iio_device_release_direct_mode(indio_dev);
}
return ret;
}
static const struct iio_event_spec fxls8962af_event[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_EITHER,
.mask_separate = BIT(IIO_EV_INFO_ENABLE),
},
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_FALLING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
},
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
},
};
#define FXLS8962AF_CHANNEL(axis, reg, idx) { \
.type = IIO_ACCEL, \
.address = reg, \
.modified = 1, \
.channel2 = IIO_MOD_##axis, \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \
BIT(IIO_CHAN_INFO_SAMP_FREQ), \
.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SCALE) | \
BIT(IIO_CHAN_INFO_SAMP_FREQ), \
.scan_index = idx, \
.scan_type = { \
.sign = 's', \
.realbits = 12, \
.storagebits = 16, \
.shift = 4, \
.endianness = IIO_BE, \
}, \
.event_spec = fxls8962af_event, \
.num_event_specs = ARRAY_SIZE(fxls8962af_event), \
}
#define FXLS8962AF_TEMP_CHANNEL { \
.type = IIO_TEMP, \
.address = FXLS8962AF_TEMP_OUT, \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_OFFSET),\
.scan_index = -1, \
.scan_type = { \
.realbits = 8, \
.storagebits = 8, \
}, \
}
static const struct iio_chan_spec fxls8962af_channels[] = {
FXLS8962AF_CHANNEL(X, FXLS8962AF_OUT_X_LSB, fxls8962af_idx_x),
FXLS8962AF_CHANNEL(Y, FXLS8962AF_OUT_Y_LSB, fxls8962af_idx_y),
FXLS8962AF_CHANNEL(Z, FXLS8962AF_OUT_Z_LSB, fxls8962af_idx_z),
IIO_CHAN_SOFT_TIMESTAMP(fxls8962af_idx_ts),
FXLS8962AF_TEMP_CHANNEL,
};
static const struct fxls8962af_chip_info fxls_chip_info_table[] = {
[fxls8962af] = {
.chip_id = FXLS8962AF_DEVICE_ID,
.name = "fxls8962af",
.channels = fxls8962af_channels,
.num_channels = ARRAY_SIZE(fxls8962af_channels),
},
[fxls8964af] = {
.chip_id = FXLS8964AF_DEVICE_ID,
.name = "fxls8964af",
.channels = fxls8962af_channels,
.num_channels = ARRAY_SIZE(fxls8962af_channels),
},
};
static const struct iio_info fxls8962af_info = {
.read_raw = &fxls8962af_read_raw,
.write_raw = &fxls8962af_write_raw,
.write_raw_get_fmt = fxls8962af_write_raw_get_fmt,
.read_event_value = fxls8962af_read_event,
.write_event_value = fxls8962af_write_event,
.read_event_config = fxls8962af_read_event_config,
.write_event_config = fxls8962af_write_event_config,
.read_avail = fxls8962af_read_avail,
.hwfifo_set_watermark = fxls8962af_set_watermark,
};
static int fxls8962af_reset(struct fxls8962af_data *data)
{
struct device *dev = regmap_get_device(data->regmap);
unsigned int reg;
int ret;
ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG1,
FXLS8962AF_SENS_CONFIG1_RST,
FXLS8962AF_SENS_CONFIG1_RST);
if (ret)
return ret;
/* TBOOT1, TBOOT2, specifies we have to wait between 1 - 17.7ms */
ret = regmap_read_poll_timeout(data->regmap, FXLS8962AF_INT_STATUS, reg,
(reg & FXLS8962AF_INT_STATUS_SRC_BOOT),
1000, 18000);
if (ret == -ETIMEDOUT)
dev_err(dev, "reset timeout, int_status = 0x%x\n", reg);
return ret;
}
static int __fxls8962af_fifo_set_mode(struct fxls8962af_data *data, bool onoff)
{
int ret;
/* Enable watermark at max fifo size */
ret = regmap_update_bits(data->regmap, FXLS8962AF_BUF_CONFIG2,
FXLS8962AF_BUF_CONFIG2_BUF_WMRK,
data->watermark);
if (ret)
return ret;
return regmap_update_bits(data->regmap, FXLS8962AF_BUF_CONFIG1,
FXLS8962AF_BC1_BUF_MODE_MASK,
FXLS8962AF_BC1_BUF_MODE_PREP(onoff));
}
static int fxls8962af_buffer_preenable(struct iio_dev *indio_dev)
{
return fxls8962af_power_on(iio_priv(indio_dev));
}
static int fxls8962af_buffer_postenable(struct iio_dev *indio_dev)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
int ret;
fxls8962af_standby(data);
/* Enable buffer interrupt */
ret = regmap_update_bits(data->regmap, FXLS8962AF_INT_EN,
FXLS8962AF_INT_EN_BUF_EN,
FXLS8962AF_INT_EN_BUF_EN);
if (ret)
return ret;
ret = __fxls8962af_fifo_set_mode(data, true);
fxls8962af_active(data);
return ret;
}
static int fxls8962af_buffer_predisable(struct iio_dev *indio_dev)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
int ret;
fxls8962af_standby(data);
/* Disable buffer interrupt */
ret = regmap_update_bits(data->regmap, FXLS8962AF_INT_EN,
FXLS8962AF_INT_EN_BUF_EN, 0);
if (ret)
return ret;
ret = __fxls8962af_fifo_set_mode(data, false);
if (data->enable_event)
fxls8962af_active(data);
return ret;
}
static int fxls8962af_buffer_postdisable(struct iio_dev *indio_dev)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
if (!data->enable_event)
fxls8962af_power_off(data);
return 0;
}
static const struct iio_buffer_setup_ops fxls8962af_buffer_ops = {
.preenable = fxls8962af_buffer_preenable,
.postenable = fxls8962af_buffer_postenable,
.predisable = fxls8962af_buffer_predisable,
.postdisable = fxls8962af_buffer_postdisable,
};
static int fxls8962af_i2c_raw_read_errata3(struct fxls8962af_data *data,
u16 *buffer, int samples,
int sample_length)
{
int i, ret;
for (i = 0; i < samples; i++) {
ret = regmap_raw_read(data->regmap, FXLS8962AF_BUF_X_LSB,
&buffer[i * 3], sample_length);
if (ret)
return ret;
}
return 0;
}
static int fxls8962af_fifo_transfer(struct fxls8962af_data *data,
u16 *buffer, int samples)
{
struct device *dev = regmap_get_device(data->regmap);
int sample_length = 3 * sizeof(*buffer);
int total_length = samples * sample_length;
int ret;
if (i2c_verify_client(dev))
/*
* Due to errata bug:
* E3: FIFO burst read operation error using I2C interface
* We have to avoid burst reads on I2C..
*/
ret = fxls8962af_i2c_raw_read_errata3(data, buffer, samples,
sample_length);
else
ret = regmap_raw_read(data->regmap, FXLS8962AF_BUF_X_LSB, buffer,
total_length);
if (ret)
dev_err(dev, "Error transferring data from fifo: %d\n", ret);
return ret;
}
static int fxls8962af_fifo_flush(struct iio_dev *indio_dev)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
struct device *dev = regmap_get_device(data->regmap);
u16 buffer[FXLS8962AF_FIFO_LENGTH * 3];
uint64_t sample_period;
unsigned int reg;
int64_t tstamp;
int ret, i;
u8 count;
ret = regmap_read(data->regmap, FXLS8962AF_BUF_STATUS, &reg);
if (ret)
return ret;
if (reg & FXLS8962AF_BUF_STATUS_BUF_OVF) {
dev_err(dev, "Buffer overflow");
return -EOVERFLOW;
}
count = reg & FXLS8962AF_BUF_STATUS_BUF_CNT;
if (!count)
return 0;
data->old_timestamp = data->timestamp;
data->timestamp = iio_get_time_ns(indio_dev);
/*
* Approximate timestamps for each of the sample based on the sampling,
* frequency, timestamp for last sample and number of samples.
*/
sample_period = (data->timestamp - data->old_timestamp);
do_div(sample_period, count);
tstamp = data->timestamp - (count - 1) * sample_period;
ret = fxls8962af_fifo_transfer(data, buffer, count);
if (ret)
return ret;
/* Demux hw FIFO into kfifo. */
for (i = 0; i < count; i++) {
int j, bit;
j = 0;
for_each_set_bit(bit, indio_dev->active_scan_mask,
indio_dev->masklength) {
memcpy(&data->scan.channels[j++], &buffer[i * 3 + bit],
sizeof(data->scan.channels[0]));
}
iio_push_to_buffers_with_timestamp(indio_dev, &data->scan,
tstamp);
tstamp += sample_period;
}
return count;
}
static int fxls8962af_event_interrupt(struct iio_dev *indio_dev)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
s64 ts = iio_get_time_ns(indio_dev);
unsigned int reg;
u64 ev_code;
int ret;
ret = regmap_read(data->regmap, FXLS8962AF_SDCD_INT_SRC1, &reg);
if (ret)
return ret;
if (reg & FXLS8962AF_SDCD_INT_SRC1_X_OT) {
ev_code = reg & FXLS8962AF_SDCD_INT_SRC1_X_POL ?
IIO_EV_DIR_RISING : IIO_EV_DIR_FALLING;
iio_push_event(indio_dev,
IIO_MOD_EVENT_CODE(IIO_ACCEL, 0, IIO_MOD_X,
IIO_EV_TYPE_THRESH, ev_code), ts);
}
if (reg & FXLS8962AF_SDCD_INT_SRC1_Y_OT) {
ev_code = reg & FXLS8962AF_SDCD_INT_SRC1_Y_POL ?
IIO_EV_DIR_RISING : IIO_EV_DIR_FALLING;
iio_push_event(indio_dev,
IIO_MOD_EVENT_CODE(IIO_ACCEL, 0, IIO_MOD_X,
IIO_EV_TYPE_THRESH, ev_code), ts);
}
if (reg & FXLS8962AF_SDCD_INT_SRC1_Z_OT) {
ev_code = reg & FXLS8962AF_SDCD_INT_SRC1_Z_POL ?
IIO_EV_DIR_RISING : IIO_EV_DIR_FALLING;
iio_push_event(indio_dev,
IIO_MOD_EVENT_CODE(IIO_ACCEL, 0, IIO_MOD_X,
IIO_EV_TYPE_THRESH, ev_code), ts);
}
return 0;
}
static irqreturn_t fxls8962af_interrupt(int irq, void *p)
{
struct iio_dev *indio_dev = p;
struct fxls8962af_data *data = iio_priv(indio_dev);
unsigned int reg;
int ret;
ret = regmap_read(data->regmap, FXLS8962AF_INT_STATUS, &reg);
if (ret)
return IRQ_NONE;
if (reg & FXLS8962AF_INT_STATUS_SRC_BUF) {
ret = fxls8962af_fifo_flush(indio_dev);
if (ret < 0)
return IRQ_NONE;
return IRQ_HANDLED;
}
if (reg & FXLS8962AF_INT_STATUS_SRC_SDCD_OT) {
ret = fxls8962af_event_interrupt(indio_dev);
if (ret < 0)
return IRQ_NONE;
return IRQ_HANDLED;
}
return IRQ_NONE;
}
static void fxls8962af_regulator_disable(void *data_ptr)
{
struct fxls8962af_data *data = data_ptr;
regulator_disable(data->vdd_reg);
}
static void fxls8962af_pm_disable(void *dev_ptr)
{
struct device *dev = dev_ptr;
struct iio_dev *indio_dev = dev_get_drvdata(dev);
pm_runtime_disable(dev);
pm_runtime_set_suspended(dev);
pm_runtime_put_noidle(dev);
fxls8962af_standby(iio_priv(indio_dev));
}
static void fxls8962af_get_irq(struct device_node *of_node,
enum fxls8962af_int_pin *pin)
{
int irq;
irq = of_irq_get_byname(of_node, "INT2");
if (irq > 0) {
*pin = FXLS8962AF_PIN_INT2;
return;
}
*pin = FXLS8962AF_PIN_INT1;
}
static int fxls8962af_irq_setup(struct iio_dev *indio_dev, int irq)
{
struct fxls8962af_data *data = iio_priv(indio_dev);
struct device *dev = regmap_get_device(data->regmap);
unsigned long irq_type;
bool irq_active_high;
enum fxls8962af_int_pin int_pin;
u8 int_pin_sel;
int ret;
fxls8962af_get_irq(dev->of_node, &int_pin);
switch (int_pin) {
case FXLS8962AF_PIN_INT1:
int_pin_sel = FXLS8962AF_INT_PIN_SEL_INT1;
break;
case FXLS8962AF_PIN_INT2:
int_pin_sel = FXLS8962AF_INT_PIN_SEL_INT2;
break;
default:
dev_err(dev, "unsupported int pin selected\n");
return -EINVAL;
}
ret = regmap_update_bits(data->regmap, FXLS8962AF_INT_PIN_SEL,
FXLS8962AF_INT_PIN_SEL_MASK, int_pin_sel);
if (ret)
return ret;
irq_type = irqd_get_trigger_type(irq_get_irq_data(irq));
switch (irq_type) {
case IRQF_TRIGGER_HIGH:
case IRQF_TRIGGER_RISING:
irq_active_high = true;
break;
case IRQF_TRIGGER_LOW:
case IRQF_TRIGGER_FALLING:
irq_active_high = false;
break;
default:
dev_info(dev, "mode %lx unsupported\n", irq_type);
return -EINVAL;
}
ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG4,
FXLS8962AF_SC4_INT_POL_MASK,
FXLS8962AF_SC4_INT_POL_PREP(irq_active_high));
if (ret)
return ret;
if (device_property_read_bool(dev, "drive-open-drain")) {
ret = regmap_update_bits(data->regmap, FXLS8962AF_SENS_CONFIG4,
FXLS8962AF_SC4_INT_PP_OD_MASK,
FXLS8962AF_SC4_INT_PP_OD_PREP(1));
if (ret)
return ret;
irq_type |= IRQF_SHARED;
}
return devm_request_threaded_irq(dev,
irq,
NULL, fxls8962af_interrupt,
irq_type | IRQF_ONESHOT,
indio_dev->name, indio_dev);
}
int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq)
{
struct fxls8962af_data *data;
struct iio_dev *indio_dev;
unsigned int reg;
int ret, i;
indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
if (!indio_dev)
return -ENOMEM;
data = iio_priv(indio_dev);
dev_set_drvdata(dev, indio_dev);
data->regmap = regmap;
data->irq = irq;
ret = iio_read_mount_matrix(dev, &data->orientation);
if (ret)
return ret;
data->vdd_reg = devm_regulator_get(dev, "vdd");
if (IS_ERR(data->vdd_reg))
return dev_err_probe(dev, PTR_ERR(data->vdd_reg),
"Failed to get vdd regulator\n");
ret = regulator_enable(data->vdd_reg);
if (ret) {
dev_err(dev, "Failed to enable vdd regulator: %d\n", ret);
return ret;
}
ret = devm_add_action_or_reset(dev, fxls8962af_regulator_disable, data);
if (ret)
return ret;
ret = regmap_read(data->regmap, FXLS8962AF_WHO_AM_I, &reg);
if (ret)
return ret;
for (i = 0; i < ARRAY_SIZE(fxls_chip_info_table); i++) {
if (fxls_chip_info_table[i].chip_id == reg) {
data->chip_info = &fxls_chip_info_table[i];
break;
}
}
if (i == ARRAY_SIZE(fxls_chip_info_table)) {
dev_err(dev, "failed to match device in table\n");
return -ENXIO;
}
indio_dev->channels = data->chip_info->channels;
indio_dev->num_channels = data->chip_info->num_channels;
indio_dev->name = data->chip_info->name;
indio_dev->info = &fxls8962af_info;
indio_dev->modes = INDIO_DIRECT_MODE;
ret = fxls8962af_reset(data);
if (ret)
return ret;
if (irq) {
ret = fxls8962af_irq_setup(indio_dev, irq);
if (ret)
return ret;
ret = devm_iio_kfifo_buffer_setup(dev, indio_dev,
INDIO_BUFFER_SOFTWARE,
&fxls8962af_buffer_ops);
if (ret)
return ret;
}
ret = pm_runtime_set_active(dev);
if (ret)
return ret;
pm_runtime_enable(dev);
pm_runtime_set_autosuspend_delay(dev, FXLS8962AF_AUTO_SUSPEND_DELAY_MS);
pm_runtime_use_autosuspend(dev);
ret = devm_add_action_or_reset(dev, fxls8962af_pm_disable, dev);
if (ret)
return ret;
if (device_property_read_bool(dev, "wakeup-source"))
device_init_wakeup(dev, true);
return devm_iio_device_register(dev, indio_dev);
}
EXPORT_SYMBOL_GPL(fxls8962af_core_probe);
static int __maybe_unused fxls8962af_runtime_suspend(struct device *dev)
{
struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
int ret;
ret = fxls8962af_standby(data);
if (ret) {
dev_err(dev, "powering off device failed\n");
return ret;
}
return 0;
}
static int __maybe_unused fxls8962af_runtime_resume(struct device *dev)
{
struct fxls8962af_data *data = iio_priv(dev_get_drvdata(dev));
return fxls8962af_active(data);
}
static int __maybe_unused fxls8962af_suspend(struct device *dev)
{
struct iio_dev *indio_dev = dev_get_drvdata(dev);
struct fxls8962af_data *data = iio_priv(indio_dev);
if (device_may_wakeup(dev) && data->enable_event) {
enable_irq_wake(data->irq);
/*
* Disable buffer, as the buffer is so small the device will wake
* almost immediately.
*/
if (iio_buffer_enabled(indio_dev))
fxls8962af_buffer_predisable(indio_dev);
} else {
fxls8962af_runtime_suspend(dev);
}
return 0;
}
static int __maybe_unused fxls8962af_resume(struct device *dev)
{
struct iio_dev *indio_dev = dev_get_drvdata(dev);
struct fxls8962af_data *data = iio_priv(indio_dev);
if (device_may_wakeup(dev) && data->enable_event) {
disable_irq_wake(data->irq);
if (iio_buffer_enabled(indio_dev))
fxls8962af_buffer_postenable(indio_dev);
} else {
fxls8962af_runtime_resume(dev);
}
return 0;
}
const struct dev_pm_ops fxls8962af_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(fxls8962af_suspend, fxls8962af_resume)
SET_RUNTIME_PM_OPS(fxls8962af_runtime_suspend,
fxls8962af_runtime_resume, NULL)
};
EXPORT_SYMBOL_GPL(fxls8962af_pm_ops);
MODULE_AUTHOR("Sean Nyekjaer <sean@geanix.com>");
MODULE_DESCRIPTION("NXP FXLS8962AF/FXLS8964AF accelerometer driver");
MODULE_LICENSE("GPL v2");