mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-08-23 17:30:02 +00:00
![Heiko Schocher](/assets/img/avatar_default.png)
add compatible entry in nxp_fspi driver for imx8mp. Signed-off-by: Heiko Schocher <hs@denx.de> Link: https://lore.kernel.org/r/20210316075928.1763460-2-hs@denx.de Signed-off-by: Mark Brown <broonie@kernel.org>
1282 lines
34 KiB
C
1282 lines
34 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
|
|
/*
|
|
* NXP FlexSPI(FSPI) controller driver.
|
|
*
|
|
* Copyright 2019-2020 NXP
|
|
* Copyright 2020 Puresoftware Ltd.
|
|
*
|
|
* FlexSPI is a flexsible SPI host controller which supports two SPI
|
|
* channels and up to 4 external devices. Each channel supports
|
|
* Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
|
|
* data lines).
|
|
*
|
|
* FlexSPI controller is driven by the LUT(Look-up Table) registers
|
|
* LUT registers are a look-up-table for sequences of instructions.
|
|
* A valid sequence consists of four LUT registers.
|
|
* Maximum 32 LUT sequences can be programmed simultaneously.
|
|
*
|
|
* LUTs are being created at run-time based on the commands passed
|
|
* from the spi-mem framework, thus using single LUT index.
|
|
*
|
|
* Software triggered Flash read/write access by IP Bus.
|
|
*
|
|
* Memory mapped read access by AHB Bus.
|
|
*
|
|
* Based on SPI MEM interface and spi-fsl-qspi.c driver.
|
|
*
|
|
* Author:
|
|
* Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
|
|
* Boris Brezillon <bbrezillon@kernel.org>
|
|
* Frieder Schrempf <frieder.schrempf@kontron.de>
|
|
*/
|
|
|
|
#include <linux/acpi.h>
|
|
#include <linux/bitops.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/completion.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/err.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/jiffies.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_qos.h>
|
|
#include <linux/regmap.h>
|
|
#include <linux/sizes.h>
|
|
#include <linux/sys_soc.h>
|
|
|
|
#include <linux/mfd/syscon.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/spi-mem.h>
|
|
|
|
/*
|
|
* The driver only uses one single LUT entry, that is updated on
|
|
* each call of exec_op(). Index 0 is preset at boot with a basic
|
|
* read operation, so let's use the last entry (31).
|
|
*/
|
|
#define SEQID_LUT 31
|
|
|
|
/* Registers used by the driver */
|
|
#define FSPI_MCR0 0x00
|
|
#define FSPI_MCR0_AHB_TIMEOUT(x) ((x) << 24)
|
|
#define FSPI_MCR0_IP_TIMEOUT(x) ((x) << 16)
|
|
#define FSPI_MCR0_LEARN_EN BIT(15)
|
|
#define FSPI_MCR0_SCRFRUN_EN BIT(14)
|
|
#define FSPI_MCR0_OCTCOMB_EN BIT(13)
|
|
#define FSPI_MCR0_DOZE_EN BIT(12)
|
|
#define FSPI_MCR0_HSEN BIT(11)
|
|
#define FSPI_MCR0_SERCLKDIV BIT(8)
|
|
#define FSPI_MCR0_ATDF_EN BIT(7)
|
|
#define FSPI_MCR0_ARDF_EN BIT(6)
|
|
#define FSPI_MCR0_RXCLKSRC(x) ((x) << 4)
|
|
#define FSPI_MCR0_END_CFG(x) ((x) << 2)
|
|
#define FSPI_MCR0_MDIS BIT(1)
|
|
#define FSPI_MCR0_SWRST BIT(0)
|
|
|
|
#define FSPI_MCR1 0x04
|
|
#define FSPI_MCR1_SEQ_TIMEOUT(x) ((x) << 16)
|
|
#define FSPI_MCR1_AHB_TIMEOUT(x) (x)
|
|
|
|
#define FSPI_MCR2 0x08
|
|
#define FSPI_MCR2_IDLE_WAIT(x) ((x) << 24)
|
|
#define FSPI_MCR2_SAMEDEVICEEN BIT(15)
|
|
#define FSPI_MCR2_CLRLRPHS BIT(14)
|
|
#define FSPI_MCR2_ABRDATSZ BIT(8)
|
|
#define FSPI_MCR2_ABRLEARN BIT(7)
|
|
#define FSPI_MCR2_ABR_READ BIT(6)
|
|
#define FSPI_MCR2_ABRWRITE BIT(5)
|
|
#define FSPI_MCR2_ABRDUMMY BIT(4)
|
|
#define FSPI_MCR2_ABR_MODE BIT(3)
|
|
#define FSPI_MCR2_ABRCADDR BIT(2)
|
|
#define FSPI_MCR2_ABRRADDR BIT(1)
|
|
#define FSPI_MCR2_ABR_CMD BIT(0)
|
|
|
|
#define FSPI_AHBCR 0x0c
|
|
#define FSPI_AHBCR_RDADDROPT BIT(6)
|
|
#define FSPI_AHBCR_PREF_EN BIT(5)
|
|
#define FSPI_AHBCR_BUFF_EN BIT(4)
|
|
#define FSPI_AHBCR_CACH_EN BIT(3)
|
|
#define FSPI_AHBCR_CLRTXBUF BIT(2)
|
|
#define FSPI_AHBCR_CLRRXBUF BIT(1)
|
|
#define FSPI_AHBCR_PAR_EN BIT(0)
|
|
|
|
#define FSPI_INTEN 0x10
|
|
#define FSPI_INTEN_SCLKSBWR BIT(9)
|
|
#define FSPI_INTEN_SCLKSBRD BIT(8)
|
|
#define FSPI_INTEN_DATALRNFL BIT(7)
|
|
#define FSPI_INTEN_IPTXWE BIT(6)
|
|
#define FSPI_INTEN_IPRXWA BIT(5)
|
|
#define FSPI_INTEN_AHBCMDERR BIT(4)
|
|
#define FSPI_INTEN_IPCMDERR BIT(3)
|
|
#define FSPI_INTEN_AHBCMDGE BIT(2)
|
|
#define FSPI_INTEN_IPCMDGE BIT(1)
|
|
#define FSPI_INTEN_IPCMDDONE BIT(0)
|
|
|
|
#define FSPI_INTR 0x14
|
|
#define FSPI_INTR_SCLKSBWR BIT(9)
|
|
#define FSPI_INTR_SCLKSBRD BIT(8)
|
|
#define FSPI_INTR_DATALRNFL BIT(7)
|
|
#define FSPI_INTR_IPTXWE BIT(6)
|
|
#define FSPI_INTR_IPRXWA BIT(5)
|
|
#define FSPI_INTR_AHBCMDERR BIT(4)
|
|
#define FSPI_INTR_IPCMDERR BIT(3)
|
|
#define FSPI_INTR_AHBCMDGE BIT(2)
|
|
#define FSPI_INTR_IPCMDGE BIT(1)
|
|
#define FSPI_INTR_IPCMDDONE BIT(0)
|
|
|
|
#define FSPI_LUTKEY 0x18
|
|
#define FSPI_LUTKEY_VALUE 0x5AF05AF0
|
|
|
|
#define FSPI_LCKCR 0x1C
|
|
|
|
#define FSPI_LCKER_LOCK 0x1
|
|
#define FSPI_LCKER_UNLOCK 0x2
|
|
|
|
#define FSPI_BUFXCR_INVALID_MSTRID 0xE
|
|
#define FSPI_AHBRX_BUF0CR0 0x20
|
|
#define FSPI_AHBRX_BUF1CR0 0x24
|
|
#define FSPI_AHBRX_BUF2CR0 0x28
|
|
#define FSPI_AHBRX_BUF3CR0 0x2C
|
|
#define FSPI_AHBRX_BUF4CR0 0x30
|
|
#define FSPI_AHBRX_BUF5CR0 0x34
|
|
#define FSPI_AHBRX_BUF6CR0 0x38
|
|
#define FSPI_AHBRX_BUF7CR0 0x3C
|
|
#define FSPI_AHBRXBUF0CR7_PREF BIT(31)
|
|
|
|
#define FSPI_AHBRX_BUF0CR1 0x40
|
|
#define FSPI_AHBRX_BUF1CR1 0x44
|
|
#define FSPI_AHBRX_BUF2CR1 0x48
|
|
#define FSPI_AHBRX_BUF3CR1 0x4C
|
|
#define FSPI_AHBRX_BUF4CR1 0x50
|
|
#define FSPI_AHBRX_BUF5CR1 0x54
|
|
#define FSPI_AHBRX_BUF6CR1 0x58
|
|
#define FSPI_AHBRX_BUF7CR1 0x5C
|
|
|
|
#define FSPI_FLSHA1CR0 0x60
|
|
#define FSPI_FLSHA2CR0 0x64
|
|
#define FSPI_FLSHB1CR0 0x68
|
|
#define FSPI_FLSHB2CR0 0x6C
|
|
#define FSPI_FLSHXCR0_SZ_KB 10
|
|
#define FSPI_FLSHXCR0_SZ(x) ((x) >> FSPI_FLSHXCR0_SZ_KB)
|
|
|
|
#define FSPI_FLSHA1CR1 0x70
|
|
#define FSPI_FLSHA2CR1 0x74
|
|
#define FSPI_FLSHB1CR1 0x78
|
|
#define FSPI_FLSHB2CR1 0x7C
|
|
#define FSPI_FLSHXCR1_CSINTR(x) ((x) << 16)
|
|
#define FSPI_FLSHXCR1_CAS(x) ((x) << 11)
|
|
#define FSPI_FLSHXCR1_WA BIT(10)
|
|
#define FSPI_FLSHXCR1_TCSH(x) ((x) << 5)
|
|
#define FSPI_FLSHXCR1_TCSS(x) (x)
|
|
|
|
#define FSPI_FLSHA1CR2 0x80
|
|
#define FSPI_FLSHA2CR2 0x84
|
|
#define FSPI_FLSHB1CR2 0x88
|
|
#define FSPI_FLSHB2CR2 0x8C
|
|
#define FSPI_FLSHXCR2_CLRINSP BIT(24)
|
|
#define FSPI_FLSHXCR2_AWRWAIT BIT(16)
|
|
#define FSPI_FLSHXCR2_AWRSEQN_SHIFT 13
|
|
#define FSPI_FLSHXCR2_AWRSEQI_SHIFT 8
|
|
#define FSPI_FLSHXCR2_ARDSEQN_SHIFT 5
|
|
#define FSPI_FLSHXCR2_ARDSEQI_SHIFT 0
|
|
|
|
#define FSPI_IPCR0 0xA0
|
|
|
|
#define FSPI_IPCR1 0xA4
|
|
#define FSPI_IPCR1_IPAREN BIT(31)
|
|
#define FSPI_IPCR1_SEQNUM_SHIFT 24
|
|
#define FSPI_IPCR1_SEQID_SHIFT 16
|
|
#define FSPI_IPCR1_IDATSZ(x) (x)
|
|
|
|
#define FSPI_IPCMD 0xB0
|
|
#define FSPI_IPCMD_TRG BIT(0)
|
|
|
|
#define FSPI_DLPR 0xB4
|
|
|
|
#define FSPI_IPRXFCR 0xB8
|
|
#define FSPI_IPRXFCR_CLR BIT(0)
|
|
#define FSPI_IPRXFCR_DMA_EN BIT(1)
|
|
#define FSPI_IPRXFCR_WMRK(x) ((x) << 2)
|
|
|
|
#define FSPI_IPTXFCR 0xBC
|
|
#define FSPI_IPTXFCR_CLR BIT(0)
|
|
#define FSPI_IPTXFCR_DMA_EN BIT(1)
|
|
#define FSPI_IPTXFCR_WMRK(x) ((x) << 2)
|
|
|
|
#define FSPI_DLLACR 0xC0
|
|
#define FSPI_DLLACR_OVRDEN BIT(8)
|
|
|
|
#define FSPI_DLLBCR 0xC4
|
|
#define FSPI_DLLBCR_OVRDEN BIT(8)
|
|
|
|
#define FSPI_STS0 0xE0
|
|
#define FSPI_STS0_DLPHB(x) ((x) << 8)
|
|
#define FSPI_STS0_DLPHA(x) ((x) << 4)
|
|
#define FSPI_STS0_CMD_SRC(x) ((x) << 2)
|
|
#define FSPI_STS0_ARB_IDLE BIT(1)
|
|
#define FSPI_STS0_SEQ_IDLE BIT(0)
|
|
|
|
#define FSPI_STS1 0xE4
|
|
#define FSPI_STS1_IP_ERRCD(x) ((x) << 24)
|
|
#define FSPI_STS1_IP_ERRID(x) ((x) << 16)
|
|
#define FSPI_STS1_AHB_ERRCD(x) ((x) << 8)
|
|
#define FSPI_STS1_AHB_ERRID(x) (x)
|
|
|
|
#define FSPI_AHBSPNST 0xEC
|
|
#define FSPI_AHBSPNST_DATLFT(x) ((x) << 16)
|
|
#define FSPI_AHBSPNST_BUFID(x) ((x) << 1)
|
|
#define FSPI_AHBSPNST_ACTIVE BIT(0)
|
|
|
|
#define FSPI_IPRXFSTS 0xF0
|
|
#define FSPI_IPRXFSTS_RDCNTR(x) ((x) << 16)
|
|
#define FSPI_IPRXFSTS_FILL(x) (x)
|
|
|
|
#define FSPI_IPTXFSTS 0xF4
|
|
#define FSPI_IPTXFSTS_WRCNTR(x) ((x) << 16)
|
|
#define FSPI_IPTXFSTS_FILL(x) (x)
|
|
|
|
#define FSPI_RFDR 0x100
|
|
#define FSPI_TFDR 0x180
|
|
|
|
#define FSPI_LUT_BASE 0x200
|
|
#define FSPI_LUT_OFFSET (SEQID_LUT * 4 * 4)
|
|
#define FSPI_LUT_REG(idx) \
|
|
(FSPI_LUT_BASE + FSPI_LUT_OFFSET + (idx) * 4)
|
|
|
|
/* register map end */
|
|
|
|
/* Instruction set for the LUT register. */
|
|
#define LUT_STOP 0x00
|
|
#define LUT_CMD 0x01
|
|
#define LUT_ADDR 0x02
|
|
#define LUT_CADDR_SDR 0x03
|
|
#define LUT_MODE 0x04
|
|
#define LUT_MODE2 0x05
|
|
#define LUT_MODE4 0x06
|
|
#define LUT_MODE8 0x07
|
|
#define LUT_NXP_WRITE 0x08
|
|
#define LUT_NXP_READ 0x09
|
|
#define LUT_LEARN_SDR 0x0A
|
|
#define LUT_DATSZ_SDR 0x0B
|
|
#define LUT_DUMMY 0x0C
|
|
#define LUT_DUMMY_RWDS_SDR 0x0D
|
|
#define LUT_JMP_ON_CS 0x1F
|
|
#define LUT_CMD_DDR 0x21
|
|
#define LUT_ADDR_DDR 0x22
|
|
#define LUT_CADDR_DDR 0x23
|
|
#define LUT_MODE_DDR 0x24
|
|
#define LUT_MODE2_DDR 0x25
|
|
#define LUT_MODE4_DDR 0x26
|
|
#define LUT_MODE8_DDR 0x27
|
|
#define LUT_WRITE_DDR 0x28
|
|
#define LUT_READ_DDR 0x29
|
|
#define LUT_LEARN_DDR 0x2A
|
|
#define LUT_DATSZ_DDR 0x2B
|
|
#define LUT_DUMMY_DDR 0x2C
|
|
#define LUT_DUMMY_RWDS_DDR 0x2D
|
|
|
|
/*
|
|
* Calculate number of required PAD bits for LUT register.
|
|
*
|
|
* The pad stands for the number of IO lines [0:7].
|
|
* For example, the octal read needs eight IO lines,
|
|
* so you should use LUT_PAD(8). This macro
|
|
* returns 3 i.e. use eight (2^3) IP lines for read.
|
|
*/
|
|
#define LUT_PAD(x) (fls(x) - 1)
|
|
|
|
/*
|
|
* Macro for constructing the LUT entries with the following
|
|
* register layout:
|
|
*
|
|
* ---------------------------------------------------
|
|
* | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
|
|
* ---------------------------------------------------
|
|
*/
|
|
#define PAD_SHIFT 8
|
|
#define INSTR_SHIFT 10
|
|
#define OPRND_SHIFT 16
|
|
|
|
/* Macros for constructing the LUT register. */
|
|
#define LUT_DEF(idx, ins, pad, opr) \
|
|
((((ins) << INSTR_SHIFT) | ((pad) << PAD_SHIFT) | \
|
|
(opr)) << (((idx) % 2) * OPRND_SHIFT))
|
|
|
|
#define POLL_TOUT 5000
|
|
#define NXP_FSPI_MAX_CHIPSELECT 4
|
|
#define NXP_FSPI_MIN_IOMAP SZ_4M
|
|
|
|
#define DCFG_RCWSR1 0x100
|
|
|
|
/* Access flash memory using IP bus only */
|
|
#define FSPI_QUIRK_USE_IP_ONLY BIT(0)
|
|
|
|
struct nxp_fspi_devtype_data {
|
|
unsigned int rxfifo;
|
|
unsigned int txfifo;
|
|
unsigned int ahb_buf_size;
|
|
unsigned int quirks;
|
|
bool little_endian;
|
|
};
|
|
|
|
static struct nxp_fspi_devtype_data lx2160a_data = {
|
|
.rxfifo = SZ_512, /* (64 * 64 bits) */
|
|
.txfifo = SZ_1K, /* (128 * 64 bits) */
|
|
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
|
|
.quirks = 0,
|
|
.little_endian = true, /* little-endian */
|
|
};
|
|
|
|
static struct nxp_fspi_devtype_data imx8mm_data = {
|
|
.rxfifo = SZ_512, /* (64 * 64 bits) */
|
|
.txfifo = SZ_1K, /* (128 * 64 bits) */
|
|
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
|
|
.quirks = 0,
|
|
.little_endian = true, /* little-endian */
|
|
};
|
|
|
|
static struct nxp_fspi_devtype_data imx8qxp_data = {
|
|
.rxfifo = SZ_512, /* (64 * 64 bits) */
|
|
.txfifo = SZ_1K, /* (128 * 64 bits) */
|
|
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
|
|
.quirks = 0,
|
|
.little_endian = true, /* little-endian */
|
|
};
|
|
|
|
static struct nxp_fspi_devtype_data imx8dxl_data = {
|
|
.rxfifo = SZ_512, /* (64 * 64 bits) */
|
|
.txfifo = SZ_1K, /* (128 * 64 bits) */
|
|
.ahb_buf_size = SZ_2K, /* (256 * 64 bits) */
|
|
.quirks = FSPI_QUIRK_USE_IP_ONLY,
|
|
.little_endian = true, /* little-endian */
|
|
};
|
|
|
|
struct nxp_fspi {
|
|
void __iomem *iobase;
|
|
void __iomem *ahb_addr;
|
|
u32 memmap_phy;
|
|
u32 memmap_phy_size;
|
|
u32 memmap_start;
|
|
u32 memmap_len;
|
|
struct clk *clk, *clk_en;
|
|
struct device *dev;
|
|
struct completion c;
|
|
struct nxp_fspi_devtype_data *devtype_data;
|
|
struct mutex lock;
|
|
struct pm_qos_request pm_qos_req;
|
|
int selected;
|
|
};
|
|
|
|
static inline int needs_ip_only(struct nxp_fspi *f)
|
|
{
|
|
return f->devtype_data->quirks & FSPI_QUIRK_USE_IP_ONLY;
|
|
}
|
|
|
|
/*
|
|
* R/W functions for big- or little-endian registers:
|
|
* The FSPI controller's endianness is independent of
|
|
* the CPU core's endianness. So far, although the CPU
|
|
* core is little-endian the FSPI controller can use
|
|
* big-endian or little-endian.
|
|
*/
|
|
static void fspi_writel(struct nxp_fspi *f, u32 val, void __iomem *addr)
|
|
{
|
|
if (f->devtype_data->little_endian)
|
|
iowrite32(val, addr);
|
|
else
|
|
iowrite32be(val, addr);
|
|
}
|
|
|
|
static u32 fspi_readl(struct nxp_fspi *f, void __iomem *addr)
|
|
{
|
|
if (f->devtype_data->little_endian)
|
|
return ioread32(addr);
|
|
else
|
|
return ioread32be(addr);
|
|
}
|
|
|
|
static irqreturn_t nxp_fspi_irq_handler(int irq, void *dev_id)
|
|
{
|
|
struct nxp_fspi *f = dev_id;
|
|
u32 reg;
|
|
|
|
/* clear interrupt */
|
|
reg = fspi_readl(f, f->iobase + FSPI_INTR);
|
|
fspi_writel(f, FSPI_INTR_IPCMDDONE, f->iobase + FSPI_INTR);
|
|
|
|
if (reg & FSPI_INTR_IPCMDDONE)
|
|
complete(&f->c);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int nxp_fspi_check_buswidth(struct nxp_fspi *f, u8 width)
|
|
{
|
|
switch (width) {
|
|
case 1:
|
|
case 2:
|
|
case 4:
|
|
case 8:
|
|
return 0;
|
|
}
|
|
|
|
return -ENOTSUPP;
|
|
}
|
|
|
|
static bool nxp_fspi_supports_op(struct spi_mem *mem,
|
|
const struct spi_mem_op *op)
|
|
{
|
|
struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
|
|
int ret;
|
|
|
|
ret = nxp_fspi_check_buswidth(f, op->cmd.buswidth);
|
|
|
|
if (op->addr.nbytes)
|
|
ret |= nxp_fspi_check_buswidth(f, op->addr.buswidth);
|
|
|
|
if (op->dummy.nbytes)
|
|
ret |= nxp_fspi_check_buswidth(f, op->dummy.buswidth);
|
|
|
|
if (op->data.nbytes)
|
|
ret |= nxp_fspi_check_buswidth(f, op->data.buswidth);
|
|
|
|
if (ret)
|
|
return false;
|
|
|
|
/*
|
|
* The number of address bytes should be equal to or less than 4 bytes.
|
|
*/
|
|
if (op->addr.nbytes > 4)
|
|
return false;
|
|
|
|
/*
|
|
* If requested address value is greater than controller assigned
|
|
* memory mapped space, return error as it didn't fit in the range
|
|
* of assigned address space.
|
|
*/
|
|
if (op->addr.val >= f->memmap_phy_size)
|
|
return false;
|
|
|
|
/* Max 64 dummy clock cycles supported */
|
|
if (op->dummy.buswidth &&
|
|
(op->dummy.nbytes * 8 / op->dummy.buswidth > 64))
|
|
return false;
|
|
|
|
/* Max data length, check controller limits and alignment */
|
|
if (op->data.dir == SPI_MEM_DATA_IN &&
|
|
(op->data.nbytes > f->devtype_data->ahb_buf_size ||
|
|
(op->data.nbytes > f->devtype_data->rxfifo - 4 &&
|
|
!IS_ALIGNED(op->data.nbytes, 8))))
|
|
return false;
|
|
|
|
if (op->data.dir == SPI_MEM_DATA_OUT &&
|
|
op->data.nbytes > f->devtype_data->txfifo)
|
|
return false;
|
|
|
|
return spi_mem_default_supports_op(mem, op);
|
|
}
|
|
|
|
/* Instead of busy looping invoke readl_poll_timeout functionality. */
|
|
static int fspi_readl_poll_tout(struct nxp_fspi *f, void __iomem *base,
|
|
u32 mask, u32 delay_us,
|
|
u32 timeout_us, bool c)
|
|
{
|
|
u32 reg;
|
|
|
|
if (!f->devtype_data->little_endian)
|
|
mask = (u32)cpu_to_be32(mask);
|
|
|
|
if (c)
|
|
return readl_poll_timeout(base, reg, (reg & mask),
|
|
delay_us, timeout_us);
|
|
else
|
|
return readl_poll_timeout(base, reg, !(reg & mask),
|
|
delay_us, timeout_us);
|
|
}
|
|
|
|
/*
|
|
* If the slave device content being changed by Write/Erase, need to
|
|
* invalidate the AHB buffer. This can be achieved by doing the reset
|
|
* of controller after setting MCR0[SWRESET] bit.
|
|
*/
|
|
static inline void nxp_fspi_invalid(struct nxp_fspi *f)
|
|
{
|
|
u32 reg;
|
|
int ret;
|
|
|
|
reg = fspi_readl(f, f->iobase + FSPI_MCR0);
|
|
fspi_writel(f, reg | FSPI_MCR0_SWRST, f->iobase + FSPI_MCR0);
|
|
|
|
/* w1c register, wait unit clear */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
|
|
FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
|
|
WARN_ON(ret);
|
|
}
|
|
|
|
static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
|
|
const struct spi_mem_op *op)
|
|
{
|
|
void __iomem *base = f->iobase;
|
|
u32 lutval[4] = {};
|
|
int lutidx = 1, i;
|
|
|
|
/* cmd */
|
|
lutval[0] |= LUT_DEF(0, LUT_CMD, LUT_PAD(op->cmd.buswidth),
|
|
op->cmd.opcode);
|
|
|
|
/* addr bytes */
|
|
if (op->addr.nbytes) {
|
|
lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_ADDR,
|
|
LUT_PAD(op->addr.buswidth),
|
|
op->addr.nbytes * 8);
|
|
lutidx++;
|
|
}
|
|
|
|
/* dummy bytes, if needed */
|
|
if (op->dummy.nbytes) {
|
|
lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_DUMMY,
|
|
/*
|
|
* Due to FlexSPI controller limitation number of PAD for dummy
|
|
* buswidth needs to be programmed as equal to data buswidth.
|
|
*/
|
|
LUT_PAD(op->data.buswidth),
|
|
op->dummy.nbytes * 8 /
|
|
op->dummy.buswidth);
|
|
lutidx++;
|
|
}
|
|
|
|
/* read/write data bytes */
|
|
if (op->data.nbytes) {
|
|
lutval[lutidx / 2] |= LUT_DEF(lutidx,
|
|
op->data.dir == SPI_MEM_DATA_IN ?
|
|
LUT_NXP_READ : LUT_NXP_WRITE,
|
|
LUT_PAD(op->data.buswidth),
|
|
0);
|
|
lutidx++;
|
|
}
|
|
|
|
/* stop condition. */
|
|
lutval[lutidx / 2] |= LUT_DEF(lutidx, LUT_STOP, 0, 0);
|
|
|
|
/* unlock LUT */
|
|
fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
|
|
fspi_writel(f, FSPI_LCKER_UNLOCK, f->iobase + FSPI_LCKCR);
|
|
|
|
/* fill LUT */
|
|
for (i = 0; i < ARRAY_SIZE(lutval); i++)
|
|
fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i));
|
|
|
|
dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x], size: 0x%08x\n",
|
|
op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3], op->data.nbytes);
|
|
|
|
/* lock LUT */
|
|
fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
|
|
fspi_writel(f, FSPI_LCKER_LOCK, f->iobase + FSPI_LCKCR);
|
|
}
|
|
|
|
static int nxp_fspi_clk_prep_enable(struct nxp_fspi *f)
|
|
{
|
|
int ret;
|
|
|
|
if (is_acpi_node(f->dev->fwnode))
|
|
return 0;
|
|
|
|
ret = clk_prepare_enable(f->clk_en);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = clk_prepare_enable(f->clk);
|
|
if (ret) {
|
|
clk_disable_unprepare(f->clk_en);
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int nxp_fspi_clk_disable_unprep(struct nxp_fspi *f)
|
|
{
|
|
if (is_acpi_node(f->dev->fwnode))
|
|
return 0;
|
|
|
|
clk_disable_unprepare(f->clk);
|
|
clk_disable_unprepare(f->clk_en);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* In FlexSPI controller, flash access is based on value of FSPI_FLSHXXCR0
|
|
* register and start base address of the slave device.
|
|
*
|
|
* (Higher address)
|
|
* -------- <-- FLSHB2CR0
|
|
* | B2 |
|
|
* | |
|
|
* B2 start address --> -------- <-- FLSHB1CR0
|
|
* | B1 |
|
|
* | |
|
|
* B1 start address --> -------- <-- FLSHA2CR0
|
|
* | A2 |
|
|
* | |
|
|
* A2 start address --> -------- <-- FLSHA1CR0
|
|
* | A1 |
|
|
* | |
|
|
* A1 start address --> -------- (Lower address)
|
|
*
|
|
*
|
|
* Start base address defines the starting address range for given CS and
|
|
* FSPI_FLSHXXCR0 defines the size of the slave device connected at given CS.
|
|
*
|
|
* But, different targets are having different combinations of number of CS,
|
|
* some targets only have single CS or two CS covering controller's full
|
|
* memory mapped space area.
|
|
* Thus, implementation is being done as independent of the size and number
|
|
* of the connected slave device.
|
|
* Assign controller memory mapped space size as the size to the connected
|
|
* slave device.
|
|
* Mark FLSHxxCR0 as zero initially and then assign value only to the selected
|
|
* chip-select Flash configuration register.
|
|
*
|
|
* For e.g. to access CS2 (B1), FLSHB1CR0 register would be equal to the
|
|
* memory mapped size of the controller.
|
|
* Value for rest of the CS FLSHxxCR0 register would be zero.
|
|
*
|
|
*/
|
|
static void nxp_fspi_select_mem(struct nxp_fspi *f, struct spi_device *spi)
|
|
{
|
|
unsigned long rate = spi->max_speed_hz;
|
|
int ret;
|
|
uint64_t size_kb;
|
|
|
|
/*
|
|
* Return, if previously selected slave device is same as current
|
|
* requested slave device.
|
|
*/
|
|
if (f->selected == spi->chip_select)
|
|
return;
|
|
|
|
/* Reset FLSHxxCR0 registers */
|
|
fspi_writel(f, 0, f->iobase + FSPI_FLSHA1CR0);
|
|
fspi_writel(f, 0, f->iobase + FSPI_FLSHA2CR0);
|
|
fspi_writel(f, 0, f->iobase + FSPI_FLSHB1CR0);
|
|
fspi_writel(f, 0, f->iobase + FSPI_FLSHB2CR0);
|
|
|
|
/* Assign controller memory mapped space as size, KBytes, of flash. */
|
|
size_kb = FSPI_FLSHXCR0_SZ(f->memmap_phy_size);
|
|
|
|
fspi_writel(f, size_kb, f->iobase + FSPI_FLSHA1CR0 +
|
|
4 * spi->chip_select);
|
|
|
|
dev_dbg(f->dev, "Slave device [CS:%x] selected\n", spi->chip_select);
|
|
|
|
nxp_fspi_clk_disable_unprep(f);
|
|
|
|
ret = clk_set_rate(f->clk, rate);
|
|
if (ret)
|
|
return;
|
|
|
|
ret = nxp_fspi_clk_prep_enable(f);
|
|
if (ret)
|
|
return;
|
|
|
|
f->selected = spi->chip_select;
|
|
}
|
|
|
|
static int nxp_fspi_read_ahb(struct nxp_fspi *f, const struct spi_mem_op *op)
|
|
{
|
|
u32 start = op->addr.val;
|
|
u32 len = op->data.nbytes;
|
|
|
|
/* if necessary, ioremap before AHB read */
|
|
if ((!f->ahb_addr) || start < f->memmap_start ||
|
|
start + len > f->memmap_start + f->memmap_len) {
|
|
if (f->ahb_addr)
|
|
iounmap(f->ahb_addr);
|
|
|
|
f->memmap_start = start;
|
|
f->memmap_len = len > NXP_FSPI_MIN_IOMAP ?
|
|
len : NXP_FSPI_MIN_IOMAP;
|
|
|
|
f->ahb_addr = ioremap_wc(f->memmap_phy + f->memmap_start,
|
|
f->memmap_len);
|
|
|
|
if (!f->ahb_addr) {
|
|
dev_err(f->dev, "failed to alloc memory\n");
|
|
return -ENOMEM;
|
|
}
|
|
}
|
|
|
|
/* Read out the data directly from the AHB buffer. */
|
|
memcpy_fromio(op->data.buf.in,
|
|
f->ahb_addr + start - f->memmap_start, len);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void nxp_fspi_fill_txfifo(struct nxp_fspi *f,
|
|
const struct spi_mem_op *op)
|
|
{
|
|
void __iomem *base = f->iobase;
|
|
int i, ret;
|
|
u8 *buf = (u8 *) op->data.buf.out;
|
|
|
|
/* clear the TX FIFO. */
|
|
fspi_writel(f, FSPI_IPTXFCR_CLR, base + FSPI_IPTXFCR);
|
|
|
|
/*
|
|
* Default value of water mark level is 8 bytes, hence in single
|
|
* write request controller can write max 8 bytes of data.
|
|
*/
|
|
|
|
for (i = 0; i < ALIGN_DOWN(op->data.nbytes, 8); i += 8) {
|
|
/* Wait for TXFIFO empty */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
|
|
FSPI_INTR_IPTXWE, 0,
|
|
POLL_TOUT, true);
|
|
WARN_ON(ret);
|
|
|
|
fspi_writel(f, *(u32 *) (buf + i), base + FSPI_TFDR);
|
|
fspi_writel(f, *(u32 *) (buf + i + 4), base + FSPI_TFDR + 4);
|
|
fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
|
|
}
|
|
|
|
if (i < op->data.nbytes) {
|
|
u32 data = 0;
|
|
int j;
|
|
/* Wait for TXFIFO empty */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
|
|
FSPI_INTR_IPTXWE, 0,
|
|
POLL_TOUT, true);
|
|
WARN_ON(ret);
|
|
|
|
for (j = 0; j < ALIGN(op->data.nbytes - i, 4); j += 4) {
|
|
memcpy(&data, buf + i + j, 4);
|
|
fspi_writel(f, data, base + FSPI_TFDR + j);
|
|
}
|
|
fspi_writel(f, FSPI_INTR_IPTXWE, base + FSPI_INTR);
|
|
}
|
|
}
|
|
|
|
static void nxp_fspi_read_rxfifo(struct nxp_fspi *f,
|
|
const struct spi_mem_op *op)
|
|
{
|
|
void __iomem *base = f->iobase;
|
|
int i, ret;
|
|
int len = op->data.nbytes;
|
|
u8 *buf = (u8 *) op->data.buf.in;
|
|
|
|
/*
|
|
* Default value of water mark level is 8 bytes, hence in single
|
|
* read request controller can read max 8 bytes of data.
|
|
*/
|
|
for (i = 0; i < ALIGN_DOWN(len, 8); i += 8) {
|
|
/* Wait for RXFIFO available */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
|
|
FSPI_INTR_IPRXWA, 0,
|
|
POLL_TOUT, true);
|
|
WARN_ON(ret);
|
|
|
|
*(u32 *)(buf + i) = fspi_readl(f, base + FSPI_RFDR);
|
|
*(u32 *)(buf + i + 4) = fspi_readl(f, base + FSPI_RFDR + 4);
|
|
/* move the FIFO pointer */
|
|
fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
|
|
}
|
|
|
|
if (i < len) {
|
|
u32 tmp;
|
|
int size, j;
|
|
|
|
buf = op->data.buf.in + i;
|
|
/* Wait for RXFIFO available */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_INTR,
|
|
FSPI_INTR_IPRXWA, 0,
|
|
POLL_TOUT, true);
|
|
WARN_ON(ret);
|
|
|
|
len = op->data.nbytes - i;
|
|
for (j = 0; j < op->data.nbytes - i; j += 4) {
|
|
tmp = fspi_readl(f, base + FSPI_RFDR + j);
|
|
size = min(len, 4);
|
|
memcpy(buf + j, &tmp, size);
|
|
len -= size;
|
|
}
|
|
}
|
|
|
|
/* invalid the RXFIFO */
|
|
fspi_writel(f, FSPI_IPRXFCR_CLR, base + FSPI_IPRXFCR);
|
|
/* move the FIFO pointer */
|
|
fspi_writel(f, FSPI_INTR_IPRXWA, base + FSPI_INTR);
|
|
}
|
|
|
|
static int nxp_fspi_do_op(struct nxp_fspi *f, const struct spi_mem_op *op)
|
|
{
|
|
void __iomem *base = f->iobase;
|
|
int seqnum = 0;
|
|
int err = 0;
|
|
u32 reg;
|
|
|
|
reg = fspi_readl(f, base + FSPI_IPRXFCR);
|
|
/* invalid RXFIFO first */
|
|
reg &= ~FSPI_IPRXFCR_DMA_EN;
|
|
reg = reg | FSPI_IPRXFCR_CLR;
|
|
fspi_writel(f, reg, base + FSPI_IPRXFCR);
|
|
|
|
init_completion(&f->c);
|
|
|
|
fspi_writel(f, op->addr.val, base + FSPI_IPCR0);
|
|
/*
|
|
* Always start the sequence at the same index since we update
|
|
* the LUT at each exec_op() call. And also specify the DATA
|
|
* length, since it's has not been specified in the LUT.
|
|
*/
|
|
fspi_writel(f, op->data.nbytes |
|
|
(SEQID_LUT << FSPI_IPCR1_SEQID_SHIFT) |
|
|
(seqnum << FSPI_IPCR1_SEQNUM_SHIFT),
|
|
base + FSPI_IPCR1);
|
|
|
|
/* Trigger the LUT now. */
|
|
fspi_writel(f, FSPI_IPCMD_TRG, base + FSPI_IPCMD);
|
|
|
|
/* Wait for the interrupt. */
|
|
if (!wait_for_completion_timeout(&f->c, msecs_to_jiffies(1000)))
|
|
err = -ETIMEDOUT;
|
|
|
|
/* Invoke IP data read, if request is of data read. */
|
|
if (!err && op->data.nbytes && op->data.dir == SPI_MEM_DATA_IN)
|
|
nxp_fspi_read_rxfifo(f, op);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
|
|
{
|
|
struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
|
|
int err = 0;
|
|
|
|
mutex_lock(&f->lock);
|
|
|
|
/* Wait for controller being ready. */
|
|
err = fspi_readl_poll_tout(f, f->iobase + FSPI_STS0,
|
|
FSPI_STS0_ARB_IDLE, 1, POLL_TOUT, true);
|
|
WARN_ON(err);
|
|
|
|
nxp_fspi_select_mem(f, mem->spi);
|
|
|
|
nxp_fspi_prepare_lut(f, op);
|
|
/*
|
|
* If we have large chunks of data, we read them through the AHB bus by
|
|
* accessing the mapped memory. In all other cases we use IP commands
|
|
* to access the flash. Read via AHB bus may be corrupted due to
|
|
* existence of an errata and therefore discard AHB read in such cases.
|
|
*/
|
|
if (op->data.nbytes > (f->devtype_data->rxfifo - 4) &&
|
|
op->data.dir == SPI_MEM_DATA_IN &&
|
|
!needs_ip_only(f)) {
|
|
err = nxp_fspi_read_ahb(f, op);
|
|
} else {
|
|
if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
|
|
nxp_fspi_fill_txfifo(f, op);
|
|
|
|
err = nxp_fspi_do_op(f, op);
|
|
}
|
|
|
|
/* Invalidate the data in the AHB buffer. */
|
|
nxp_fspi_invalid(f);
|
|
|
|
mutex_unlock(&f->lock);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int nxp_fspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
|
|
{
|
|
struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
|
|
|
|
if (op->data.dir == SPI_MEM_DATA_OUT) {
|
|
if (op->data.nbytes > f->devtype_data->txfifo)
|
|
op->data.nbytes = f->devtype_data->txfifo;
|
|
} else {
|
|
if (op->data.nbytes > f->devtype_data->ahb_buf_size)
|
|
op->data.nbytes = f->devtype_data->ahb_buf_size;
|
|
else if (op->data.nbytes > (f->devtype_data->rxfifo - 4))
|
|
op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
|
|
}
|
|
|
|
/* Limit data bytes to RX FIFO in case of IP read only */
|
|
if (op->data.dir == SPI_MEM_DATA_IN &&
|
|
needs_ip_only(f) &&
|
|
op->data.nbytes > f->devtype_data->rxfifo)
|
|
op->data.nbytes = f->devtype_data->rxfifo;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void erratum_err050568(struct nxp_fspi *f)
|
|
{
|
|
const struct soc_device_attribute ls1028a_soc_attr[] = {
|
|
{ .family = "QorIQ LS1028A" },
|
|
{ /* sentinel */ }
|
|
};
|
|
struct device_node *np;
|
|
struct regmap *map;
|
|
u32 val = 0, sysclk = 0;
|
|
int ret;
|
|
|
|
/* Check for LS1028A family */
|
|
if (!soc_device_match(ls1028a_soc_attr)) {
|
|
dev_dbg(f->dev, "Errata applicable only for LS1028A\n");
|
|
return;
|
|
}
|
|
|
|
/* Compute system clock frequency multiplier ratio */
|
|
map = syscon_regmap_lookup_by_compatible("fsl,ls1028a-dcfg");
|
|
if (IS_ERR(map)) {
|
|
dev_err(f->dev, "No syscon regmap\n");
|
|
goto err;
|
|
}
|
|
|
|
ret = regmap_read(map, DCFG_RCWSR1, &val);
|
|
if (ret < 0)
|
|
goto err;
|
|
|
|
/* Strap bits 6:2 define SYS_PLL_RAT i.e frequency multiplier ratio */
|
|
val = (val >> 2) & 0x1F;
|
|
WARN(val == 0, "Strapping is zero: Cannot determine ratio");
|
|
|
|
/* Compute system clock frequency */
|
|
np = of_find_node_by_name(NULL, "clock-sysclk");
|
|
if (!np)
|
|
goto err;
|
|
|
|
if (of_property_read_u32(np, "clock-frequency", &sysclk))
|
|
goto err;
|
|
|
|
sysclk = (sysclk * val) / 1000000; /* Convert sysclk to Mhz */
|
|
dev_dbg(f->dev, "val: 0x%08x, sysclk: %dMhz\n", val, sysclk);
|
|
|
|
/* Use IP bus only if PLL is 300MHz */
|
|
if (sysclk == 300)
|
|
f->devtype_data->quirks |= FSPI_QUIRK_USE_IP_ONLY;
|
|
|
|
return;
|
|
|
|
err:
|
|
dev_err(f->dev, "Errata cannot be executed. Read via IP bus may not work\n");
|
|
}
|
|
|
|
static int nxp_fspi_default_setup(struct nxp_fspi *f)
|
|
{
|
|
void __iomem *base = f->iobase;
|
|
int ret, i;
|
|
u32 reg;
|
|
|
|
/* disable and unprepare clock to avoid glitch pass to controller */
|
|
nxp_fspi_clk_disable_unprep(f);
|
|
|
|
/* the default frequency, we will change it later if necessary. */
|
|
ret = clk_set_rate(f->clk, 20000000);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ret = nxp_fspi_clk_prep_enable(f);
|
|
if (ret)
|
|
return ret;
|
|
|
|
/*
|
|
* ERR050568: Flash access by FlexSPI AHB command may not work with
|
|
* platform frequency equal to 300 MHz on LS1028A.
|
|
* LS1028A reuses LX2160A compatible entry. Make errata applicable for
|
|
* Layerscape LS1028A platform.
|
|
*/
|
|
if (of_device_is_compatible(f->dev->of_node, "nxp,lx2160a-fspi"))
|
|
erratum_err050568(f);
|
|
|
|
/* Reset the module */
|
|
/* w1c register, wait unit clear */
|
|
ret = fspi_readl_poll_tout(f, f->iobase + FSPI_MCR0,
|
|
FSPI_MCR0_SWRST, 0, POLL_TOUT, false);
|
|
WARN_ON(ret);
|
|
|
|
/* Disable the module */
|
|
fspi_writel(f, FSPI_MCR0_MDIS, base + FSPI_MCR0);
|
|
|
|
/* Reset the DLL register to default value */
|
|
fspi_writel(f, FSPI_DLLACR_OVRDEN, base + FSPI_DLLACR);
|
|
fspi_writel(f, FSPI_DLLBCR_OVRDEN, base + FSPI_DLLBCR);
|
|
|
|
/* enable module */
|
|
fspi_writel(f, FSPI_MCR0_AHB_TIMEOUT(0xFF) |
|
|
FSPI_MCR0_IP_TIMEOUT(0xFF) | (u32) FSPI_MCR0_OCTCOMB_EN,
|
|
base + FSPI_MCR0);
|
|
|
|
/*
|
|
* Disable same device enable bit and configure all slave devices
|
|
* independently.
|
|
*/
|
|
reg = fspi_readl(f, f->iobase + FSPI_MCR2);
|
|
reg = reg & ~(FSPI_MCR2_SAMEDEVICEEN);
|
|
fspi_writel(f, reg, base + FSPI_MCR2);
|
|
|
|
/* AHB configuration for access buffer 0~7. */
|
|
for (i = 0; i < 7; i++)
|
|
fspi_writel(f, 0, base + FSPI_AHBRX_BUF0CR0 + 4 * i);
|
|
|
|
/*
|
|
* Set ADATSZ with the maximum AHB buffer size to improve the read
|
|
* performance.
|
|
*/
|
|
fspi_writel(f, (f->devtype_data->ahb_buf_size / 8 |
|
|
FSPI_AHBRXBUF0CR7_PREF), base + FSPI_AHBRX_BUF7CR0);
|
|
|
|
/* prefetch and no start address alignment limitation */
|
|
fspi_writel(f, FSPI_AHBCR_PREF_EN | FSPI_AHBCR_RDADDROPT,
|
|
base + FSPI_AHBCR);
|
|
|
|
/* AHB Read - Set lut sequence ID for all CS. */
|
|
fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA1CR2);
|
|
fspi_writel(f, SEQID_LUT, base + FSPI_FLSHA2CR2);
|
|
fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB1CR2);
|
|
fspi_writel(f, SEQID_LUT, base + FSPI_FLSHB2CR2);
|
|
|
|
f->selected = -1;
|
|
|
|
/* enable the interrupt */
|
|
fspi_writel(f, FSPI_INTEN_IPCMDDONE, base + FSPI_INTEN);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const char *nxp_fspi_get_name(struct spi_mem *mem)
|
|
{
|
|
struct nxp_fspi *f = spi_controller_get_devdata(mem->spi->master);
|
|
struct device *dev = &mem->spi->dev;
|
|
const char *name;
|
|
|
|
// Set custom name derived from the platform_device of the controller.
|
|
if (of_get_available_child_count(f->dev->of_node) == 1)
|
|
return dev_name(f->dev);
|
|
|
|
name = devm_kasprintf(dev, GFP_KERNEL,
|
|
"%s-%d", dev_name(f->dev),
|
|
mem->spi->chip_select);
|
|
|
|
if (!name) {
|
|
dev_err(dev, "failed to get memory for custom flash name\n");
|
|
return ERR_PTR(-ENOMEM);
|
|
}
|
|
|
|
return name;
|
|
}
|
|
|
|
static const struct spi_controller_mem_ops nxp_fspi_mem_ops = {
|
|
.adjust_op_size = nxp_fspi_adjust_op_size,
|
|
.supports_op = nxp_fspi_supports_op,
|
|
.exec_op = nxp_fspi_exec_op,
|
|
.get_name = nxp_fspi_get_name,
|
|
};
|
|
|
|
static int nxp_fspi_probe(struct platform_device *pdev)
|
|
{
|
|
struct spi_controller *ctlr;
|
|
struct device *dev = &pdev->dev;
|
|
struct device_node *np = dev->of_node;
|
|
struct resource *res;
|
|
struct nxp_fspi *f;
|
|
int ret;
|
|
u32 reg;
|
|
|
|
ctlr = spi_alloc_master(&pdev->dev, sizeof(*f));
|
|
if (!ctlr)
|
|
return -ENOMEM;
|
|
|
|
ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL |
|
|
SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL;
|
|
|
|
f = spi_controller_get_devdata(ctlr);
|
|
f->dev = dev;
|
|
f->devtype_data = (struct nxp_fspi_devtype_data *)device_get_match_data(dev);
|
|
if (!f->devtype_data) {
|
|
ret = -ENODEV;
|
|
goto err_put_ctrl;
|
|
}
|
|
|
|
platform_set_drvdata(pdev, f);
|
|
|
|
/* find the resources - configuration register address space */
|
|
if (is_acpi_node(f->dev->fwnode))
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
else
|
|
res = platform_get_resource_byname(pdev,
|
|
IORESOURCE_MEM, "fspi_base");
|
|
|
|
f->iobase = devm_ioremap_resource(dev, res);
|
|
if (IS_ERR(f->iobase)) {
|
|
ret = PTR_ERR(f->iobase);
|
|
goto err_put_ctrl;
|
|
}
|
|
|
|
/* Clear potential interrupts */
|
|
reg = fspi_readl(f, f->iobase + FSPI_INTR);
|
|
if (reg)
|
|
fspi_writel(f, reg, f->iobase + FSPI_INTR);
|
|
|
|
|
|
/* find the resources - controller memory mapped space */
|
|
if (is_acpi_node(f->dev->fwnode))
|
|
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
|
|
else
|
|
res = platform_get_resource_byname(pdev,
|
|
IORESOURCE_MEM, "fspi_mmap");
|
|
|
|
if (!res) {
|
|
ret = -ENODEV;
|
|
goto err_put_ctrl;
|
|
}
|
|
|
|
/* assign memory mapped starting address and mapped size. */
|
|
f->memmap_phy = res->start;
|
|
f->memmap_phy_size = resource_size(res);
|
|
|
|
/* find the clocks */
|
|
if (dev_of_node(&pdev->dev)) {
|
|
f->clk_en = devm_clk_get(dev, "fspi_en");
|
|
if (IS_ERR(f->clk_en)) {
|
|
ret = PTR_ERR(f->clk_en);
|
|
goto err_put_ctrl;
|
|
}
|
|
|
|
f->clk = devm_clk_get(dev, "fspi");
|
|
if (IS_ERR(f->clk)) {
|
|
ret = PTR_ERR(f->clk);
|
|
goto err_put_ctrl;
|
|
}
|
|
|
|
ret = nxp_fspi_clk_prep_enable(f);
|
|
if (ret) {
|
|
dev_err(dev, "can not enable the clock\n");
|
|
goto err_put_ctrl;
|
|
}
|
|
}
|
|
|
|
/* find the irq */
|
|
ret = platform_get_irq(pdev, 0);
|
|
if (ret < 0)
|
|
goto err_disable_clk;
|
|
|
|
ret = devm_request_irq(dev, ret,
|
|
nxp_fspi_irq_handler, 0, pdev->name, f);
|
|
if (ret) {
|
|
dev_err(dev, "failed to request irq: %d\n", ret);
|
|
goto err_disable_clk;
|
|
}
|
|
|
|
mutex_init(&f->lock);
|
|
|
|
ctlr->bus_num = -1;
|
|
ctlr->num_chipselect = NXP_FSPI_MAX_CHIPSELECT;
|
|
ctlr->mem_ops = &nxp_fspi_mem_ops;
|
|
|
|
nxp_fspi_default_setup(f);
|
|
|
|
ctlr->dev.of_node = np;
|
|
|
|
ret = devm_spi_register_controller(&pdev->dev, ctlr);
|
|
if (ret)
|
|
goto err_destroy_mutex;
|
|
|
|
return 0;
|
|
|
|
err_destroy_mutex:
|
|
mutex_destroy(&f->lock);
|
|
|
|
err_disable_clk:
|
|
nxp_fspi_clk_disable_unprep(f);
|
|
|
|
err_put_ctrl:
|
|
spi_controller_put(ctlr);
|
|
|
|
dev_err(dev, "NXP FSPI probe failed\n");
|
|
return ret;
|
|
}
|
|
|
|
static int nxp_fspi_remove(struct platform_device *pdev)
|
|
{
|
|
struct nxp_fspi *f = platform_get_drvdata(pdev);
|
|
|
|
/* disable the hardware */
|
|
fspi_writel(f, FSPI_MCR0_MDIS, f->iobase + FSPI_MCR0);
|
|
|
|
nxp_fspi_clk_disable_unprep(f);
|
|
|
|
mutex_destroy(&f->lock);
|
|
|
|
if (f->ahb_addr)
|
|
iounmap(f->ahb_addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int nxp_fspi_suspend(struct device *dev)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static int nxp_fspi_resume(struct device *dev)
|
|
{
|
|
struct nxp_fspi *f = dev_get_drvdata(dev);
|
|
|
|
nxp_fspi_default_setup(f);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct of_device_id nxp_fspi_dt_ids[] = {
|
|
{ .compatible = "nxp,lx2160a-fspi", .data = (void *)&lx2160a_data, },
|
|
{ .compatible = "nxp,imx8mm-fspi", .data = (void *)&imx8mm_data, },
|
|
{ .compatible = "nxp,imx8mp-fspi", .data = (void *)&imx8mm_data, },
|
|
{ .compatible = "nxp,imx8qxp-fspi", .data = (void *)&imx8qxp_data, },
|
|
{ .compatible = "nxp,imx8dxl-fspi", .data = (void *)&imx8dxl_data, },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, nxp_fspi_dt_ids);
|
|
|
|
#ifdef CONFIG_ACPI
|
|
static const struct acpi_device_id nxp_fspi_acpi_ids[] = {
|
|
{ "NXP0009", .driver_data = (kernel_ulong_t)&lx2160a_data, },
|
|
{}
|
|
};
|
|
MODULE_DEVICE_TABLE(acpi, nxp_fspi_acpi_ids);
|
|
#endif
|
|
|
|
static const struct dev_pm_ops nxp_fspi_pm_ops = {
|
|
.suspend = nxp_fspi_suspend,
|
|
.resume = nxp_fspi_resume,
|
|
};
|
|
|
|
static struct platform_driver nxp_fspi_driver = {
|
|
.driver = {
|
|
.name = "nxp-fspi",
|
|
.of_match_table = nxp_fspi_dt_ids,
|
|
.acpi_match_table = ACPI_PTR(nxp_fspi_acpi_ids),
|
|
.pm = &nxp_fspi_pm_ops,
|
|
},
|
|
.probe = nxp_fspi_probe,
|
|
.remove = nxp_fspi_remove,
|
|
};
|
|
module_platform_driver(nxp_fspi_driver);
|
|
|
|
MODULE_DESCRIPTION("NXP FSPI Controller Driver");
|
|
MODULE_AUTHOR("NXP Semiconductor");
|
|
MODULE_AUTHOR("Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>");
|
|
MODULE_AUTHOR("Boris Brezillon <bbrezillon@kernel.org>");
|
|
MODULE_AUTHOR("Frieder Schrempf <frieder.schrempf@kontron.de>");
|
|
MODULE_LICENSE("GPL v2");
|