mirror of
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
synced 2024-08-26 19:00:25 +00:00
![Lucas De Marchi](/assets/img/avatar_default.png)
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
183 lines
6.4 KiB
Text
183 lines
6.4 KiB
Text
$Id: README.aha152x,v 1.2 1999/12/25 15:32:30 fischer Exp fischer $
|
|
Adaptec AHA-1520/1522 SCSI driver for Linux (aha152x)
|
|
|
|
Copyright 1993-1999 Jürgen Fischer <fischer@norbit.de>
|
|
TC1550 patches by Luuk van Dijk (ldz@xs4all.nl)
|
|
|
|
|
|
In Revision 2 the driver was modified a lot (especially the
|
|
bottom-half handler complete()).
|
|
|
|
The driver is much cleaner now, has support for the new
|
|
error handling code in 2.3, produced less cpu load (much
|
|
less polling loops), has slightly higher throughput (at
|
|
least on my ancient test box; a i486/33Mhz/20MB).
|
|
|
|
|
|
CONFIGURATION ARGUMENTS:
|
|
|
|
IOPORT base io address (0x340/0x140)
|
|
IRQ interrupt level (9-12; default 11)
|
|
SCSI_ID scsi id of controller (0-7; default 7)
|
|
RECONNECT allow targets to disconnect from the bus (0/1; default 1 [on])
|
|
PARITY enable parity checking (0/1; default 1 [on])
|
|
SYNCHRONOUS enable synchronous transfers (0/1; default 1 [on])
|
|
DELAY: bus reset delay (default 100)
|
|
EXT_TRANS: enable extended translation (0/1: default 0 [off])
|
|
(see NOTES)
|
|
|
|
COMPILE TIME CONFIGURATION (go into AHA152X in drivers/scsi/Makefile):
|
|
|
|
-DAUTOCONF
|
|
use configuration the controller reports (AHA-152x only)
|
|
|
|
-DSKIP_BIOSTEST
|
|
Don't test for BIOS signature (AHA-1510 or disabled BIOS)
|
|
|
|
-DSETUP0="{ IOPORT, IRQ, SCSI_ID, RECONNECT, PARITY, SYNCHRONOUS, DELAY, EXT_TRANS }"
|
|
override for the first controller
|
|
|
|
-DSETUP1="{ IOPORT, IRQ, SCSI_ID, RECONNECT, PARITY, SYNCHRONOUS, DELAY, EXT_TRANS }"
|
|
override for the second controller
|
|
|
|
-DAHA152X_DEBUG
|
|
enable debugging output
|
|
|
|
-DAHA152X_STAT
|
|
enable some statistics
|
|
|
|
|
|
LILO COMMAND LINE OPTIONS:
|
|
|
|
aha152x=<IOPORT>[,<IRQ>[,<SCSI-ID>[,<RECONNECT>[,<PARITY>[,<SYNCHRONOUS>[,<DELAY> [,<EXT_TRANS]]]]]]]
|
|
|
|
The normal configuration can be overridden by specifying a command line.
|
|
When you do this, the BIOS test is skipped. Entered values have to be
|
|
valid (known). Don't use values that aren't supported under normal
|
|
operation. If you think that you need other values: contact me.
|
|
For two controllers use the aha152x statement twice.
|
|
|
|
|
|
SYMBOLS FOR MODULE CONFIGURATION:
|
|
|
|
Choose from 2 alternatives:
|
|
|
|
1. specify everything (old)
|
|
|
|
aha152x=IOPORT,IRQ,SCSI_ID,RECONNECT,PARITY,SYNCHRONOUS,DELAY,EXT_TRANS
|
|
configuration override for first controller
|
|
|
|
|
|
aha152x1=IOPORT,IRQ,SCSI_ID,RECONNECT,PARITY,SYNCHRONOUS,DELAY,EXT_TRANS
|
|
configuration override for second controller
|
|
|
|
2. specify only what you need to (irq or io is required; new)
|
|
|
|
io=IOPORT0[,IOPORT1]
|
|
IOPORT for first and second controller
|
|
|
|
irq=IRQ0[,IRQ1]
|
|
IRQ for first and second controller
|
|
|
|
scsiid=SCSIID0[,SCSIID1]
|
|
SCSIID for first and second controller
|
|
|
|
reconnect=RECONNECT0[,RECONNECT1]
|
|
allow targets to disconnect for first and second controller
|
|
|
|
parity=PAR0[PAR1]
|
|
use parity for first and second controller
|
|
|
|
sync=SYNCHRONOUS0[,SYNCHRONOUS1]
|
|
enable synchronous transfers for first and second controller
|
|
|
|
delay=DELAY0[,DELAY1]
|
|
reset DELAY for first and second controller
|
|
|
|
exttrans=EXTTRANS0[,EXTTRANS1]
|
|
enable extended translation for first and second controller
|
|
|
|
|
|
If you use both alternatives the first will be taken.
|
|
|
|
|
|
NOTES ON EXT_TRANS:
|
|
|
|
SCSI uses block numbers to address blocks/sectors on a device.
|
|
The BIOS uses a cylinder/head/sector addressing scheme (C/H/S)
|
|
scheme instead. DOS expects a BIOS or driver that understands this
|
|
C/H/S addressing.
|
|
|
|
The number of cylinders/heads/sectors is called geometry and is required
|
|
as base for requests in C/H/S addressing. SCSI only knows about the
|
|
total capacity of disks in blocks (sectors).
|
|
|
|
Therefore the SCSI BIOS/DOS driver has to calculate a logical/virtual
|
|
geometry just to be able to support that addressing scheme. The geometry
|
|
returned by the SCSI BIOS is a pure calculation and has nothing to
|
|
do with the real/physical geometry of the disk (which is usually
|
|
irrelevant anyway).
|
|
|
|
Basically this has no impact at all on Linux, because it also uses block
|
|
instead of C/H/S addressing. Unfortunately C/H/S addressing is also used
|
|
in the partition table and therefore every operating system has to know
|
|
the right geometry to be able to interpret it.
|
|
|
|
Moreover there are certain limitations to the C/H/S addressing scheme,
|
|
namely the address space is limited to up to 255 heads, up to 63 sectors
|
|
and a maximum of 1023 cylinders.
|
|
|
|
The AHA-1522 BIOS calculates the geometry by fixing the number of heads
|
|
to 64, the number of sectors to 32 and by calculating the number of
|
|
cylinders by dividing the capacity reported by the disk by 64*32 (1 MB).
|
|
This is considered to be the default translation.
|
|
|
|
With respect to the limit of 1023 cylinders using C/H/S you can only
|
|
address the first GB of your disk in the partition table. Therefore
|
|
BIOSes of some newer controllers based on the AIC-6260/6360 support
|
|
extended translation. This means that the BIOS uses 255 for heads,
|
|
63 for sectors and then divides the capacity of the disk by 255*63
|
|
(about 8 MB), as soon it sees a disk greater than 1 GB. That results
|
|
in a maximum of about 8 GB addressable diskspace in the partition table
|
|
(but there are already bigger disks out there today).
|
|
|
|
To make it even more complicated the translation mode might/might
|
|
not be configurable in certain BIOS setups.
|
|
|
|
This driver does some more or less failsafe guessing to get the
|
|
geometry right in most cases:
|
|
|
|
- for disks<1GB: use default translation (C/32/64)
|
|
|
|
- for disks>1GB:
|
|
- take current geometry from the partition table
|
|
(using scsicam_bios_param and accept only `valid' geometries,
|
|
ie. either (C/32/64) or (C/63/255)). This can be extended translation
|
|
even if it's not enabled in the driver.
|
|
|
|
- if that fails, take extended translation if enabled by override,
|
|
kernel or module parameter, otherwise take default translation and
|
|
ask the user for verification. This might on not yet partitioned
|
|
disks.
|
|
|
|
|
|
REFERENCES USED:
|
|
|
|
"AIC-6260 SCSI Chip Specification", Adaptec Corporation.
|
|
|
|
"SCSI COMPUTER SYSTEM INTERFACE - 2 (SCSI-2)", X3T9.2/86-109 rev. 10h
|
|
|
|
"Writing a SCSI device driver for Linux", Rik Faith (faith@cs.unc.edu)
|
|
|
|
"Kernel Hacker's Guide", Michael K. Johnson (johnsonm@sunsite.unc.edu)
|
|
|
|
"Adaptec 1520/1522 User's Guide", Adaptec Corporation.
|
|
|
|
Michael K. Johnson (johnsonm@sunsite.unc.edu)
|
|
|
|
Drew Eckhardt (drew@cs.colorado.edu)
|
|
|
|
Eric Youngdale (eric@andante.org)
|
|
|
|
special thanks to Eric Youngdale for the free(!) supplying the
|
|
documentation on the chip.
|