mirrors/linux-stable
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git synced 2024-10-06 00:39:48 +00:00
Code Issues Releases Wiki Activity
linux-stable/drivers/media/pci/saa7134/saa7134-dvb.c
Maciej S. Szmigiero c1849372a6 media: saa7134: keep demod i2c gate closed on Medion 7134 
Medion 7134 has two i2c eeproms on the same i2c bus sharing the same bus
addresses: the first one for SAA7134 chip config and the second one behind
TDA10046 DVB-T demod chip i2c gate storing its firmware.
The TV tuner on this board is not behind this i2c gate.

Due to the bus conflict described above, the card PCI SVID / SSID sometimes
gets garbled after a reboot, which makes it necessary to specify the card
model manually as an insmod option in order for it to be detected reliably.
To avoid this, let's just leave the gate permanently closed so the eeprom
chips won't clash.

The demod firmware load is done with its i2c gate closed anyway so it is
not affected by this change.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
2019-08-26 10:45:19 -03:00

1975 lines
56 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0-or-later
/*
*
* (c) 2004 Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]
*
* Extended 3 / 2005 by Hartmut Hackmann to support various
* cards with the tda10046 DVB-T channel decoder
*/
#include "saa7134.h"
#include "saa7134-reg.h"
#include <linux/init.h>
#include <linux/list.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/kthread.h>
#include <linux/suspend.h>
#include <media/v4l2-common.h>
#include "dvb-pll.h"
#include <media/dvb_frontend.h>
#include "mt352.h"
#include "mt352_priv.h" /* FIXME */
#include "tda1004x.h"
#include "nxt200x.h"
#include "tuner-xc2028.h"
#include "xc5000.h"
#include "tda10086.h"
#include "tda826x.h"
#include "tda827x.h"
#include "isl6421.h"
#include "isl6405.h"
#include "lnbp21.h"
#include "tuner-simple.h"
#include "tda10048.h"
#include "tda18271.h"
#include "lgdt3305.h"
#include "tda8290.h"
#include "mb86a20s.h"
#include "lgs8gxx.h"
#include "zl10353.h"
#include "qt1010.h"
#include "zl10036.h"
#include "zl10039.h"
#include "mt312.h"
#include "s5h1411.h"
MODULE_AUTHOR("Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]");
MODULE_LICENSE("GPL");
static unsigned int antenna_pwr;
module_param(antenna_pwr, int, 0444);
MODULE_PARM_DESC(antenna_pwr,"enable antenna power (Pinnacle 300i)");
static int use_frontend;
module_param(use_frontend, int, 0644);
MODULE_PARM_DESC(use_frontend,"for cards with multiple frontends (0: terrestrial, 1: satellite)");
DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
/* ------------------------------------------------------------------
* mt352 based DVB-T cards
*/
static int pinnacle_antenna_pwr(struct saa7134_dev *dev, int on)
{
u32 ok;
if (!on) {
saa_setl(SAA7134_GPIO_GPMODE0 >> 2, (1 << 26));
saa_clearl(SAA7134_GPIO_GPSTATUS0 >> 2, (1 << 26));
return 0;
}
saa_setl(SAA7134_GPIO_GPMODE0 >> 2, (1 << 26));
saa_setl(SAA7134_GPIO_GPSTATUS0 >> 2, (1 << 26));
udelay(10);
saa_setl(SAA7134_GPIO_GPMODE0 >> 2, (1 << 28));
saa_clearl(SAA7134_GPIO_GPSTATUS0 >> 2, (1 << 28));
udelay(10);
saa_setl(SAA7134_GPIO_GPSTATUS0 >> 2, (1 << 28));
udelay(10);
ok = saa_readl(SAA7134_GPIO_GPSTATUS0) & (1 << 27);
pr_debug("%s %s\n", __func__, ok ? "on" : "off");
if (!ok)
saa_clearl(SAA7134_GPIO_GPSTATUS0 >> 2, (1 << 26));
return ok;
}
static int mt352_pinnacle_init(struct dvb_frontend* fe)
{
static u8 clock_config [] = { CLOCK_CTL, 0x3d, 0x28 };
static u8 reset [] = { RESET, 0x80 };
static u8 adc_ctl_1_cfg [] = { ADC_CTL_1, 0x40 };
static u8 agc_cfg [] = { AGC_TARGET, 0x28, 0xa0 };
static u8 capt_range_cfg[] = { CAPT_RANGE, 0x31 };
static u8 fsm_ctl_cfg[] = { 0x7b, 0x04 };
static u8 gpp_ctl_cfg [] = { GPP_CTL, 0x0f };
static u8 scan_ctl_cfg [] = { SCAN_CTL, 0x0d };
static u8 irq_cfg [] = { INTERRUPT_EN_0, 0x00, 0x00, 0x00, 0x00 };
pr_debug("%s called\n", __func__);
mt352_write(fe, clock_config, sizeof(clock_config));
udelay(200);
mt352_write(fe, reset, sizeof(reset));
mt352_write(fe, adc_ctl_1_cfg, sizeof(adc_ctl_1_cfg));
mt352_write(fe, agc_cfg, sizeof(agc_cfg));
mt352_write(fe, capt_range_cfg, sizeof(capt_range_cfg));
mt352_write(fe, gpp_ctl_cfg, sizeof(gpp_ctl_cfg));
mt352_write(fe, fsm_ctl_cfg, sizeof(fsm_ctl_cfg));
mt352_write(fe, scan_ctl_cfg, sizeof(scan_ctl_cfg));
mt352_write(fe, irq_cfg, sizeof(irq_cfg));
return 0;
}
static int mt352_aver777_init(struct dvb_frontend* fe)
{
static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x2d };
static u8 reset [] = { RESET, 0x80 };
static u8 adc_ctl_1_cfg [] = { ADC_CTL_1, 0x40 };
static u8 agc_cfg [] = { AGC_TARGET, 0x28, 0xa0 };
static u8 capt_range_cfg[] = { CAPT_RANGE, 0x33 };
mt352_write(fe, clock_config, sizeof(clock_config));
udelay(200);
mt352_write(fe, reset, sizeof(reset));
mt352_write(fe, adc_ctl_1_cfg, sizeof(adc_ctl_1_cfg));
mt352_write(fe, agc_cfg, sizeof(agc_cfg));
mt352_write(fe, capt_range_cfg, sizeof(capt_range_cfg));
return 0;
}
static int mt352_avermedia_xc3028_init(struct dvb_frontend *fe)
{
static u8 clock_config [] = { CLOCK_CTL, 0x38, 0x2d };
static u8 reset [] = { RESET, 0x80 };
static u8 adc_ctl_1_cfg [] = { ADC_CTL_1, 0x40 };
static u8 agc_cfg [] = { AGC_TARGET, 0xe };
static u8 capt_range_cfg[] = { CAPT_RANGE, 0x33 };
mt352_write(fe, clock_config, sizeof(clock_config));
udelay(200);
mt352_write(fe, reset, sizeof(reset));
mt352_write(fe, adc_ctl_1_cfg, sizeof(adc_ctl_1_cfg));
mt352_write(fe, agc_cfg, sizeof(agc_cfg));
mt352_write(fe, capt_range_cfg, sizeof(capt_range_cfg));
return 0;
}
static int mt352_pinnacle_tuner_set_params(struct dvb_frontend *fe)
{
struct dtv_frontend_properties *c = &fe->dtv_property_cache;
u8 off[] = { 0x00, 0xf1};
u8 on[] = { 0x00, 0x71};
struct i2c_msg msg = {.addr=0x43, .flags=0, .buf=off, .len = sizeof(off)};
struct saa7134_dev *dev = fe->dvb->priv;
struct v4l2_frequency f;
/* set frequency (mt2050) */
f.tuner = 0;
f.type = V4L2_TUNER_DIGITAL_TV;
f.frequency = c->frequency / 1000 * 16 / 1000;
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
i2c_transfer(&dev->i2c_adap, &msg, 1);
saa_call_all(dev, tuner, s_frequency, &f);
msg.buf = on;
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
i2c_transfer(&dev->i2c_adap, &msg, 1);
pinnacle_antenna_pwr(dev, antenna_pwr);
/* mt352 setup */
return mt352_pinnacle_init(fe);
}
static struct mt352_config pinnacle_300i = {
.demod_address = 0x3c >> 1,
.adc_clock = 20333,
.if2 = 36150,
.no_tuner = 1,
.demod_init = mt352_pinnacle_init,
};
static struct mt352_config avermedia_777 = {
.demod_address = 0xf,
.demod_init = mt352_aver777_init,
};
static struct mt352_config avermedia_xc3028_mt352_dev = {
.demod_address = (0x1e >> 1),
.no_tuner = 1,
.demod_init = mt352_avermedia_xc3028_init,
};
static struct tda18271_std_map mb86a20s_tda18271_std_map = {
.dvbt_6 = { .if_freq = 3300, .agc_mode = 3, .std = 4,
.if_lvl = 7, .rfagc_top = 0x37, },
};
static struct tda18271_config kworld_tda18271_config = {
.std_map = &mb86a20s_tda18271_std_map,
.gate = TDA18271_GATE_DIGITAL,
.config = 3, /* Use tuner callback for AGC */
};
static const struct mb86a20s_config kworld_mb86a20s_config = {
.demod_address = 0x10,
};
static int kworld_sbtvd_gate_ctrl(struct dvb_frontend* fe, int enable)
{
struct saa7134_dev *dev = fe->dvb->priv;
unsigned char initmsg[] = {0x45, 0x97};
unsigned char msg_enable[] = {0x45, 0xc1};
unsigned char msg_disable[] = {0x45, 0x81};
struct i2c_msg msg = {.addr = 0x4b, .flags = 0, .buf = initmsg, .len = 2};
if (i2c_transfer(&dev->i2c_adap, &msg, 1) != 1) {
pr_warn("could not access the I2C gate\n");
return -EIO;
}
if (enable)
msg.buf = msg_enable;
else
msg.buf = msg_disable;
if (i2c_transfer(&dev->i2c_adap, &msg, 1) != 1) {
pr_warn("could not access the I2C gate\n");
return -EIO;
}
msleep(20);
return 0;
}
/* ==================================================================
* tda1004x based DVB-T cards, helper functions
*/
static int philips_tda1004x_request_firmware(struct dvb_frontend *fe,
const struct firmware **fw, char *name)
{
struct saa7134_dev *dev = fe->dvb->priv;
return request_firmware(fw, name, &dev->pci->dev);
}
/* ------------------------------------------------------------------
* these tuners are tu1216, td1316(a)
*/
static int philips_tda6651_pll_set(struct dvb_frontend *fe)
{
struct dtv_frontend_properties *c = &fe->dtv_property_cache;
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
u8 addr = state->config->tuner_address;
u8 tuner_buf[4];
struct i2c_msg tuner_msg = {.addr = addr,.flags = 0,.buf = tuner_buf,.len =
sizeof(tuner_buf) };
int tuner_frequency = 0;
u8 band, cp, filter;
/* determine charge pump */
tuner_frequency = c->frequency + 36166000;
if (tuner_frequency < 87000000)
return -EINVAL;
else if (tuner_frequency < 130000000)
cp = 3;
else if (tuner_frequency < 160000000)
cp = 5;
else if (tuner_frequency < 200000000)
cp = 6;
else if (tuner_frequency < 290000000)
cp = 3;
else if (tuner_frequency < 420000000)
cp = 5;
else if (tuner_frequency < 480000000)
cp = 6;
else if (tuner_frequency < 620000000)
cp = 3;
else if (tuner_frequency < 830000000)
cp = 5;
else if (tuner_frequency < 895000000)
cp = 7;
else
return -EINVAL;
/* determine band */
if (c->frequency < 49000000)
return -EINVAL;
else if (c->frequency < 161000000)
band = 1;
else if (c->frequency < 444000000)
band = 2;
else if (c->frequency < 861000000)
band = 4;
else
return -EINVAL;
/* setup PLL filter */
switch (c->bandwidth_hz) {
case 6000000:
filter = 0;
break;
case 7000000:
filter = 0;
break;
case 8000000:
filter = 1;
break;
default:
return -EINVAL;
}
/* calculate divisor
* ((36166000+((1000000/6)/2)) + Finput)/(1000000/6)
*/
tuner_frequency = (((c->frequency / 1000) * 6) + 217496) / 1000;
/* setup tuner buffer */
tuner_buf[0] = (tuner_frequency >> 8) & 0x7f;
tuner_buf[1] = tuner_frequency & 0xff;
tuner_buf[2] = 0xca;
tuner_buf[3] = (cp << 5) | (filter << 3) | band;
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
if (i2c_transfer(&dev->i2c_adap, &tuner_msg, 1) != 1) {
pr_warn("could not write to tuner at addr: 0x%02x\n",
addr << 1);
return -EIO;
}
msleep(1);
return 0;
}
static int philips_tu1216_init(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
u8 addr = state->config->tuner_address;
static u8 tu1216_init[] = { 0x0b, 0xf5, 0x85, 0xab };
struct i2c_msg tuner_msg = {.addr = addr,.flags = 0,.buf = tu1216_init,.len = sizeof(tu1216_init) };
/* setup PLL configuration */
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
if (i2c_transfer(&dev->i2c_adap, &tuner_msg, 1) != 1)
return -EIO;
msleep(1);
return 0;
}
/* ------------------------------------------------------------------ */
static struct tda1004x_config philips_tu1216_60_config = {
.demod_address = 0x8,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_4M,
.agc_config = TDA10046_AGC_DEFAULT,
.if_freq = TDA10046_FREQ_3617,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config philips_tu1216_61_config = {
.demod_address = 0x8,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_4M,
.agc_config = TDA10046_AGC_DEFAULT,
.if_freq = TDA10046_FREQ_3617,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
/* ------------------------------------------------------------------ */
static int philips_td1316_tuner_init(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
u8 addr = state->config->tuner_address;
static u8 msg[] = { 0x0b, 0xf5, 0x86, 0xab };
struct i2c_msg init_msg = {.addr = addr,.flags = 0,.buf = msg,.len = sizeof(msg) };
/* setup PLL configuration */
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
if (i2c_transfer(&dev->i2c_adap, &init_msg, 1) != 1)
return -EIO;
return 0;
}
static int philips_td1316_tuner_set_params(struct dvb_frontend *fe)
{
return philips_tda6651_pll_set(fe);
}
static int philips_td1316_tuner_sleep(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
u8 addr = state->config->tuner_address;
static u8 msg[] = { 0x0b, 0xdc, 0x86, 0xa4 };
struct i2c_msg analog_msg = {.addr = addr,.flags = 0,.buf = msg,.len = sizeof(msg) };
/* switch the tuner to analog mode */
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
if (i2c_transfer(&dev->i2c_adap, &analog_msg, 1) != 1)
return -EIO;
return 0;
}
/* ------------------------------------------------------------------ */
static int philips_europa_tuner_init(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
static u8 msg[] = { 0x00, 0x40};
struct i2c_msg init_msg = {.addr = 0x43,.flags = 0,.buf = msg,.len = sizeof(msg) };
if (philips_td1316_tuner_init(fe))
return -EIO;
msleep(1);
if (i2c_transfer(&dev->i2c_adap, &init_msg, 1) != 1)
return -EIO;
return 0;
}
static int philips_europa_tuner_sleep(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
static u8 msg[] = { 0x00, 0x14 };
struct i2c_msg analog_msg = {.addr = 0x43,.flags = 0,.buf = msg,.len = sizeof(msg) };
if (philips_td1316_tuner_sleep(fe))
return -EIO;
/* switch the board to analog mode */
if (fe->ops.i2c_gate_ctrl)
fe->ops.i2c_gate_ctrl(fe, 1);
i2c_transfer(&dev->i2c_adap, &analog_msg, 1);
return 0;
}
static int philips_europa_demod_sleep(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
if (dev->original_demod_sleep)
dev->original_demod_sleep(fe);
fe->ops.i2c_gate_ctrl(fe, 1);
return 0;
}
static struct tda1004x_config philips_europa_config = {
.demod_address = 0x8,
.invert = 0,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_4M,
.agc_config = TDA10046_AGC_IFO_AUTO_POS,
.if_freq = TDA10046_FREQ_052,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config medion_cardbus = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_IFO_AUTO_NEG,
.if_freq = TDA10046_FREQ_3613,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config technotrend_budget_t3000_config = {
.demod_address = 0x8,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_4M,
.agc_config = TDA10046_AGC_DEFAULT,
.if_freq = TDA10046_FREQ_3617,
.tuner_address = 0x63,
.request_firmware = philips_tda1004x_request_firmware
};
/* ------------------------------------------------------------------
* tda 1004x based cards with philips silicon tuner
*/
static int tda8290_i2c_gate_ctrl( struct dvb_frontend* fe, int enable)
{
struct tda1004x_state *state = fe->demodulator_priv;
u8 addr = state->config->i2c_gate;
static u8 tda8290_close[] = { 0x21, 0xc0};
static u8 tda8290_open[] = { 0x21, 0x80};
struct i2c_msg tda8290_msg = {.addr = addr,.flags = 0, .len = 2};
if (enable) {
tda8290_msg.buf = tda8290_close;
} else {
tda8290_msg.buf = tda8290_open;
}
if (i2c_transfer(state->i2c, &tda8290_msg, 1) != 1) {
pr_warn("could not access tda8290 I2C gate\n");
return -EIO;
}
msleep(20);
return 0;
}
static int philips_tda827x_tuner_init(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
switch (state->config->antenna_switch) {
case 0:
break;
case 1:
pr_debug("setting GPIO21 to 0 (TV antenna?)\n");
saa7134_set_gpio(dev, 21, 0);
break;
case 2:
pr_debug("setting GPIO21 to 1 (Radio antenna?)\n");
saa7134_set_gpio(dev, 21, 1);
break;
}
return 0;
}
static int philips_tda827x_tuner_sleep(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
struct tda1004x_state *state = fe->demodulator_priv;
switch (state->config->antenna_switch) {
case 0:
break;
case 1:
pr_debug("setting GPIO21 to 1 (Radio antenna?)\n");
saa7134_set_gpio(dev, 21, 1);
break;
case 2:
pr_debug("setting GPIO21 to 0 (TV antenna?)\n");
saa7134_set_gpio(dev, 21, 0);
break;
}
return 0;
}
static int configure_tda827x_fe(struct saa7134_dev *dev,
struct tda1004x_config *cdec_conf,
struct tda827x_config *tuner_conf)
{
struct vb2_dvb_frontend *fe0;
/* Get the first frontend */
fe0 = vb2_dvb_get_frontend(&dev->frontends, 1);
if (!fe0)
return -EINVAL;
fe0->dvb.frontend = dvb_attach(tda10046_attach, cdec_conf, &dev->i2c_adap);
if (fe0->dvb.frontend) {
if (cdec_conf->i2c_gate)
fe0->dvb.frontend->ops.i2c_gate_ctrl = tda8290_i2c_gate_ctrl;
if (dvb_attach(tda827x_attach, fe0->dvb.frontend,
cdec_conf->tuner_address,
&dev->i2c_adap, tuner_conf))
return 0;
pr_warn("no tda827x tuner found at addr: %02x\n",
cdec_conf->tuner_address);
}
return -EINVAL;
}
/* ------------------------------------------------------------------ */
static struct tda827x_config tda827x_cfg_0 = {
.init = philips_tda827x_tuner_init,
.sleep = philips_tda827x_tuner_sleep,
.config = 0,
.switch_addr = 0
};
static struct tda827x_config tda827x_cfg_1 = {
.init = philips_tda827x_tuner_init,
.sleep = philips_tda827x_tuner_sleep,
.config = 1,
.switch_addr = 0x4b
};
static struct tda827x_config tda827x_cfg_2 = {
.init = philips_tda827x_tuner_init,
.sleep = philips_tda827x_tuner_sleep,
.config = 2,
.switch_addr = 0x4b
};
static struct tda827x_config tda827x_cfg_2_sw42 = {
.init = philips_tda827x_tuner_init,
.sleep = philips_tda827x_tuner_sleep,
.config = 2,
.switch_addr = 0x42
};
/* ------------------------------------------------------------------ */
static struct tda1004x_config tda827x_lifeview_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config philips_tiger_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config cinergy_ht_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config cinergy_ht_pci_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config philips_tiger_s_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config pinnacle_pctv_310i_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config hauppauge_hvr_1110_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config asus_p7131_dual_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 2,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config lifeview_trio_config = {
.demod_address = 0x09,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP00_I,
.if_freq = TDA10046_FREQ_045,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config tevion_dvbt220rf_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config md8800_dvbt_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x60,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config asus_p7131_4871_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 2,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config asus_p7131_hybrid_lna_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 2,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config kworld_dvb_t_210_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch= 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config avermedia_super_007_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x60,
.antenna_switch= 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config twinhan_dtv_dvb_3056_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP01_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x42,
.tuner_address = 0x61,
.antenna_switch = 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config asus_tiger_3in1_config = {
.demod_address = 0x0b,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch = 1,
.request_firmware = philips_tda1004x_request_firmware
};
static struct tda1004x_config asus_ps3_100_config = {
.demod_address = 0x0b,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP11_I,
.if_freq = TDA10046_FREQ_045,
.i2c_gate = 0x4b,
.tuner_address = 0x61,
.antenna_switch = 1,
.request_firmware = philips_tda1004x_request_firmware
};
/* ------------------------------------------------------------------
* special case: this card uses saa713x GPIO22 for the mode switch
*/
static int ads_duo_tuner_init(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
philips_tda827x_tuner_init(fe);
/* route TDA8275a AGC input to the channel decoder */
saa7134_set_gpio(dev, 22, 1);
return 0;
}
static int ads_duo_tuner_sleep(struct dvb_frontend *fe)
{
struct saa7134_dev *dev = fe->dvb->priv;
/* route TDA8275a AGC input to the analog IF chip*/
saa7134_set_gpio(dev, 22, 0);
philips_tda827x_tuner_sleep(fe);
return 0;
}
static struct tda827x_config ads_duo_cfg = {
.init = ads_duo_tuner_init,
.sleep = ads_duo_tuner_sleep,
.config = 0
};
static struct tda1004x_config ads_tech_duo_config = {
.demod_address = 0x08,
.invert = 1,
.invert_oclk = 0,
.xtal_freq = TDA10046_XTAL_16M,
.agc_config = TDA10046_AGC_TDA827X,
.gpio_config = TDA10046_GP00_I,
.if_freq = TDA10046_FREQ_045,
.tuner_address = 0x61,
.request_firmware = philips_tda1004x_request_firmware
};
static struct zl10353_config behold_h6_config = {
.demod_address = 0x1e>>1,
.no_tuner = 1,
.parallel_ts = 1,
.disable_i2c_gate_ctrl = 1,
};
static struct xc5000_config behold_x7_tunerconfig = {
.i2c_address = 0xc2>>1,
.if_khz = 4560,
.radio_input = XC5000_RADIO_FM1,
};
static struct zl10353_config behold_x7_config = {
.demod_address = 0x1e>>1,
.if2 = 45600,
.no_tuner = 1,
.parallel_ts = 1,
.disable_i2c_gate_ctrl = 1,
};
static struct zl10353_config videomate_t750_zl10353_config = {
.demod_address = 0x0f,
.no_tuner = 1,
.parallel_ts = 1,
.disable_i2c_gate_ctrl = 1,
};
static struct qt1010_config videomate_t750_qt1010_config = {
.i2c_address = 0x62
};
/* ==================================================================
* tda10086 based DVB-S cards, helper functions
*/
static struct tda10086_config flydvbs = {
.demod_address = 0x0e,
.invert = 0,
.diseqc_tone = 0,
.xtal_freq = TDA10086_XTAL_16M,
};
static struct tda10086_config sd1878_4m = {
.demod_address = 0x0e,
.invert = 0,
.diseqc_tone = 0,
.xtal_freq = TDA10086_XTAL_4M,
};
/* ------------------------------------------------------------------
* special case: lnb supply is connected to the gated i2c
*/
static int md8800_set_voltage(struct dvb_frontend *fe,
enum fe_sec_voltage voltage)
{
int res = -EIO;
struct saa7134_dev *dev = fe->dvb->priv;
if (fe->ops.i2c_gate_ctrl) {
fe->ops.i2c_gate_ctrl(fe, 1);
if (dev->original_set_voltage)
res = dev->original_set_voltage(fe, voltage);
fe->ops.i2c_gate_ctrl(fe, 0);
}
return res;
};
static int md8800_set_high_voltage(struct dvb_frontend *fe, long arg)
{
int res = -EIO;
struct saa7134_dev *dev = fe->dvb->priv;
if (fe->ops.i2c_gate_ctrl) {
fe->ops.i2c_gate_ctrl(fe, 1);
if (dev->original_set_high_voltage)
res = dev->original_set_high_voltage(fe, arg);
fe->ops.i2c_gate_ctrl(fe, 0);
}
return res;
};
static int md8800_set_voltage2(struct dvb_frontend *fe,
enum fe_sec_voltage voltage)
{
struct saa7134_dev *dev = fe->dvb->priv;
u8 wbuf[2] = { 0x1f, 00 };
u8 rbuf;
struct i2c_msg msg[] = { { .addr = 0x08, .flags = 0, .buf = wbuf, .len = 1 },
{ .addr = 0x08, .flags = I2C_M_RD, .buf = &rbuf, .len = 1 } };
if (i2c_transfer(&dev->i2c_adap, msg, 2) != 2)
return -EIO;
/* NOTE: this assumes that gpo1 is used, it might be bit 5 (gpo2) */
if (voltage == SEC_VOLTAGE_18)
wbuf[1] = rbuf | 0x10;
else
wbuf[1] = rbuf & 0xef;
msg[0].len = 2;
i2c_transfer(&dev->i2c_adap, msg, 1);
return 0;
}
static int md8800_set_high_voltage2(struct dvb_frontend *fe, long arg)
{
pr_warn("%s: sorry can't set high LNB supply voltage from here\n",
__func__);
return -EIO;
}
/* ==================================================================
* nxt200x based ATSC cards, helper functions
*/
static const struct nxt200x_config avertvhda180 = {
.demod_address = 0x0a,
};
static const struct nxt200x_config kworldatsc110 = {
.demod_address = 0x0a,
};
/* ------------------------------------------------------------------ */
static struct mt312_config avertv_a700_mt312 = {
.demod_address = 0x0e,
.voltage_inverted = 1,
};
static struct zl10036_config avertv_a700_tuner = {
.tuner_address = 0x60,
};
static struct mt312_config zl10313_compro_s350_config = {
.demod_address = 0x0e,
};
static struct mt312_config zl10313_avermedia_a706_config = {
.demod_address = 0x0e,
};
static struct lgdt3305_config hcw_lgdt3305_config = {
.i2c_addr = 0x0e,
.mpeg_mode = LGDT3305_MPEG_SERIAL,
.tpclk_edge = LGDT3305_TPCLK_RISING_EDGE,
.tpvalid_polarity = LGDT3305_TP_VALID_HIGH,
.deny_i2c_rptr = 1,
.spectral_inversion = 1,
.qam_if_khz = 4000,
.vsb_if_khz = 3250,
};
static struct tda10048_config hcw_tda10048_config = {
.demod_address = 0x10 >> 1,
.output_mode = TDA10048_SERIAL_OUTPUT,
.fwbulkwritelen = TDA10048_BULKWRITE_200,
.inversion = TDA10048_INVERSION_ON,
.dtv6_if_freq_khz = TDA10048_IF_3300,
.dtv7_if_freq_khz = TDA10048_IF_3500,
.dtv8_if_freq_khz = TDA10048_IF_4000,
.clk_freq_khz = TDA10048_CLK_16000,
.disable_gate_access = 1,
};
static struct tda18271_std_map hauppauge_tda18271_std_map = {
.atsc_6 = { .if_freq = 3250, .agc_mode = 3, .std = 4,
.if_lvl = 1, .rfagc_top = 0x58, },
.qam_6 = { .if_freq = 4000, .agc_mode = 3, .std = 5,
.if_lvl = 1, .rfagc_top = 0x58, },
};
static struct tda18271_config hcw_tda18271_config = {
.std_map = &hauppauge_tda18271_std_map,
.gate = TDA18271_GATE_ANALOG,
.config = 3,
.output_opt = TDA18271_OUTPUT_LT_OFF,
};
static struct tda829x_config tda829x_no_probe = {
.probe_tuner = TDA829X_DONT_PROBE,
};
static struct tda10048_config zolid_tda10048_config = {
.demod_address = 0x10 >> 1,
.output_mode = TDA10048_PARALLEL_OUTPUT,
.fwbulkwritelen = TDA10048_BULKWRITE_200,
.inversion = TDA10048_INVERSION_ON,
.dtv6_if_freq_khz = TDA10048_IF_3300,
.dtv7_if_freq_khz = TDA10048_IF_3500,
.dtv8_if_freq_khz = TDA10048_IF_4000,
.clk_freq_khz = TDA10048_CLK_16000,
.disable_gate_access = 1,
};
static struct tda18271_config zolid_tda18271_config = {
.gate = TDA18271_GATE_ANALOG,
};
static struct tda10048_config dtv1000s_tda10048_config = {
.demod_address = 0x10 >> 1,
.output_mode = TDA10048_PARALLEL_OUTPUT,
.fwbulkwritelen = TDA10048_BULKWRITE_200,
.inversion = TDA10048_INVERSION_ON,
.dtv6_if_freq_khz = TDA10048_IF_3300,
.dtv7_if_freq_khz = TDA10048_IF_3800,
.dtv8_if_freq_khz = TDA10048_IF_4300,
.clk_freq_khz = TDA10048_CLK_16000,
.disable_gate_access = 1,
};
static struct tda18271_std_map dtv1000s_tda18271_std_map = {
.dvbt_6 = { .if_freq = 3300, .agc_mode = 3, .std = 4,
.if_lvl = 1, .rfagc_top = 0x37, },
.dvbt_7 = { .if_freq = 3800, .agc_mode = 3, .std = 5,
.if_lvl = 1, .rfagc_top = 0x37, },
.dvbt_8 = { .if_freq = 4300, .agc_mode = 3, .std = 6,
.if_lvl = 1, .rfagc_top = 0x37, },
};
static struct tda18271_config dtv1000s_tda18271_config = {
.std_map = &dtv1000s_tda18271_std_map,
.gate = TDA18271_GATE_ANALOG,
};
static struct lgs8gxx_config prohdtv_pro2_lgs8g75_config = {
.prod = LGS8GXX_PROD_LGS8G75,
.demod_address = 0x1d,
.serial_ts = 0,
.ts_clk_pol = 1,
.ts_clk_gated = 0,
.if_clk_freq = 30400, /* 30.4 MHz */
.if_freq = 4000, /* 4.00 MHz */
.if_neg_center = 0,
.ext_adc = 0,
.adc_signed = 1,
.adc_vpp = 3, /* 2.0 Vpp */
.if_neg_edge = 1,
};
static struct tda18271_config prohdtv_pro2_tda18271_config = {
.gate = TDA18271_GATE_ANALOG,
.output_opt = TDA18271_OUTPUT_LT_OFF,
};
static struct tda18271_std_map kworld_tda18271_std_map = {
.atsc_6 = { .if_freq = 3250, .agc_mode = 3, .std = 3,
.if_lvl = 6, .rfagc_top = 0x37 },
.qam_6 = { .if_freq = 4000, .agc_mode = 3, .std = 0,
.if_lvl = 6, .rfagc_top = 0x37 },
};
static struct tda18271_config kworld_pc150u_tda18271_config = {
.std_map = &kworld_tda18271_std_map,
.gate = TDA18271_GATE_ANALOG,
.output_opt = TDA18271_OUTPUT_LT_OFF,
.config = 3, /* Use tuner callback for AGC */
.rf_cal_on_startup = 1
};
static struct s5h1411_config kworld_s5h1411_config = {
.output_mode = S5H1411_PARALLEL_OUTPUT,
.gpio = S5H1411_GPIO_OFF,
.qam_if = S5H1411_IF_4000,
.vsb_if = S5H1411_IF_3250,
.inversion = S5H1411_INVERSION_ON,
.status_mode = S5H1411_DEMODLOCKING,
.mpeg_timing =
S5H1411_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,
};
/* ==================================================================
* Core code
*/
static int dvb_init(struct saa7134_dev *dev)
{
int ret;
int attach_xc3028 = 0;
struct vb2_dvb_frontend *fe0;
struct vb2_queue *q;
/* FIXME: add support for multi-frontend */
mutex_init(&dev->frontends.lock);
INIT_LIST_HEAD(&dev->frontends.felist);
pr_info("%s() allocating 1 frontend\n", __func__);
fe0 = vb2_dvb_alloc_frontend(&dev->frontends, 1);
if (!fe0) {
pr_err("%s() failed to alloc\n", __func__);
return -ENOMEM;
}
/* init struct vb2_dvb */
dev->ts.nr_bufs = 32;
dev->ts.nr_packets = 32*4;
fe0->dvb.name = dev->name;
q = &fe0->dvb.dvbq;
q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
q->io_modes = VB2_MMAP | VB2_READ;
q->drv_priv = &dev->ts_q;
q->ops = &saa7134_ts_qops;
q->mem_ops = &vb2_dma_sg_memops;
q->buf_struct_size = sizeof(struct saa7134_buf);
q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
q->lock = &dev->lock;
q->dev = &dev->pci->dev;
ret = vb2_queue_init(q);
if (ret) {
vb2_dvb_dealloc_frontends(&dev->frontends);
return ret;
}
switch (dev->board) {
case SAA7134_BOARD_PINNACLE_300I_DVBT_PAL:
pr_debug("pinnacle 300i dvb setup\n");
fe0->dvb.frontend = dvb_attach(mt352_attach, &pinnacle_300i,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
fe0->dvb.frontend->ops.tuner_ops.set_params = mt352_pinnacle_tuner_set_params;
}
break;
case SAA7134_BOARD_AVERMEDIA_777:
case SAA7134_BOARD_AVERMEDIA_A16AR:
pr_debug("avertv 777 dvb setup\n");
fe0->dvb.frontend = dvb_attach(mt352_attach, &avermedia_777,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dvb_attach(simple_tuner_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x61,
TUNER_PHILIPS_TD1316);
}
break;
case SAA7134_BOARD_AVERMEDIA_A16D:
pr_debug("AverMedia A16D dvb setup\n");
fe0->dvb.frontend = dvb_attach(mt352_attach,
&avermedia_xc3028_mt352_dev,
&dev->i2c_adap);
attach_xc3028 = 1;
break;
case SAA7134_BOARD_MD7134:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&medion_cardbus,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
/*
* The TV tuner on this board is actually NOT
* behind the demod i2c gate.
* However, the demod EEPROM is indeed there and it
* conflicts with the SAA7134 chip config EEPROM
* if the i2c gate is open (since they have same
* bus addresses) resulting in card PCI SVID / SSID
* being garbage after a reboot from time to time.
*
* Let's just leave the gate permanently closed -
* saa7134_i2c_eeprom_md7134_gate() will close it for
* us at probe time if it was open for some reason.
*/
fe0->dvb.frontend->ops.i2c_gate_ctrl = NULL;
dvb_attach(simple_tuner_attach, fe0->dvb.frontend,
&dev->i2c_adap, medion_cardbus.tuner_address,
TUNER_PHILIPS_FMD1216ME_MK3);
}
break;
case SAA7134_BOARD_PHILIPS_TOUGH:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&philips_tu1216_60_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
fe0->dvb.frontend->ops.tuner_ops.init = philips_tu1216_init;
fe0->dvb.frontend->ops.tuner_ops.set_params = philips_tda6651_pll_set;
}
break;
case SAA7134_BOARD_FLYDVBTDUO:
case SAA7134_BOARD_FLYDVBT_DUO_CARDBUS:
if (configure_tda827x_fe(dev, &tda827x_lifeview_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_PHILIPS_EUROPA:
case SAA7134_BOARD_VIDEOMATE_DVBT_300:
case SAA7134_BOARD_ASUS_EUROPA_HYBRID:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&philips_europa_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dev->original_demod_sleep = fe0->dvb.frontend->ops.sleep;
fe0->dvb.frontend->ops.sleep = philips_europa_demod_sleep;
fe0->dvb.frontend->ops.tuner_ops.init = philips_europa_tuner_init;
fe0->dvb.frontend->ops.tuner_ops.sleep = philips_europa_tuner_sleep;
fe0->dvb.frontend->ops.tuner_ops.set_params = philips_td1316_tuner_set_params;
}
break;
case SAA7134_BOARD_TECHNOTREND_BUDGET_T3000:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&technotrend_budget_t3000_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dev->original_demod_sleep = fe0->dvb.frontend->ops.sleep;
fe0->dvb.frontend->ops.sleep = philips_europa_demod_sleep;
fe0->dvb.frontend->ops.tuner_ops.init = philips_europa_tuner_init;
fe0->dvb.frontend->ops.tuner_ops.sleep = philips_europa_tuner_sleep;
fe0->dvb.frontend->ops.tuner_ops.set_params = philips_td1316_tuner_set_params;
}
break;
case SAA7134_BOARD_VIDEOMATE_DVBT_200:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&philips_tu1216_61_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
fe0->dvb.frontend->ops.tuner_ops.init = philips_tu1216_init;
fe0->dvb.frontend->ops.tuner_ops.set_params = philips_tda6651_pll_set;
}
break;
case SAA7134_BOARD_KWORLD_DVBT_210:
if (configure_tda827x_fe(dev, &kworld_dvb_t_210_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_HAUPPAUGE_HVR1120:
fe0->dvb.frontend = dvb_attach(tda10048_attach,
&hcw_tda10048_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&hcw_tda18271_config);
}
break;
case SAA7134_BOARD_PHILIPS_TIGER:
if (configure_tda827x_fe(dev, &philips_tiger_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_PINNACLE_PCTV_310i:
if (configure_tda827x_fe(dev, &pinnacle_pctv_310i_config,
&tda827x_cfg_1) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_HAUPPAUGE_HVR1110:
if (configure_tda827x_fe(dev, &hauppauge_hvr_1110_config,
&tda827x_cfg_1) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_HAUPPAUGE_HVR1150:
fe0->dvb.frontend = dvb_attach(lgdt3305_attach,
&hcw_lgdt3305_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&hcw_tda18271_config);
}
break;
case SAA7134_BOARD_ASUSTeK_P7131_DUAL:
if (configure_tda827x_fe(dev, &asus_p7131_dual_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_FLYDVBT_LR301:
if (configure_tda827x_fe(dev, &tda827x_lifeview_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_FLYDVB_TRIO:
if (!use_frontend) { /* terrestrial */
if (configure_tda827x_fe(dev, &lifeview_trio_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
} else { /* satellite */
fe0->dvb.frontend = dvb_attach(tda10086_attach, &flydvbs, &dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda826x_attach, fe0->dvb.frontend, 0x63,
&dev->i2c_adap, 0) == NULL) {
pr_warn("%s: Lifeview Trio, No tda826x found!\n",
__func__);
goto detach_frontend;
}
if (dvb_attach(isl6421_attach, fe0->dvb.frontend,
&dev->i2c_adap,
0x08, 0, 0, false) == NULL) {
pr_warn("%s: Lifeview Trio, No ISL6421 found!\n",
__func__);
goto detach_frontend;
}
}
}
break;
case SAA7134_BOARD_ADS_DUO_CARDBUS_PTV331:
case SAA7134_BOARD_FLYDVBT_HYBRID_CARDBUS:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&ads_tech_duo_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda827x_attach,fe0->dvb.frontend,
ads_tech_duo_config.tuner_address, &dev->i2c_adap,
&ads_duo_cfg) == NULL) {
pr_warn("no tda827x tuner found at addr: %02x\n",
ads_tech_duo_config.tuner_address);
goto detach_frontend;
}
} else
pr_warn("failed to attach tda10046\n");
break;
case SAA7134_BOARD_TEVION_DVBT_220RF:
if (configure_tda827x_fe(dev, &tevion_dvbt220rf_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_MEDION_MD8800_QUADRO:
if (!use_frontend) { /* terrestrial */
if (configure_tda827x_fe(dev, &md8800_dvbt_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
} else { /* satellite */
fe0->dvb.frontend = dvb_attach(tda10086_attach,
&flydvbs, &dev->i2c_adap);
if (fe0->dvb.frontend) {
struct dvb_frontend *fe = fe0->dvb.frontend;
u8 dev_id = dev->eedata[2];
u8 data = 0xc4;
struct i2c_msg msg = {.addr = 0x08, .flags = 0, .len = 1};
if (dvb_attach(tda826x_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap, 0) == NULL) {
pr_warn("%s: Medion Quadro, no tda826x found !\n",
__func__);
goto detach_frontend;
}
if (dev_id != 0x08) {
/* we need to open the i2c gate (we know it exists) */
fe->ops.i2c_gate_ctrl(fe, 1);
if (dvb_attach(isl6405_attach, fe,
&dev->i2c_adap, 0x08, 0, 0) == NULL) {
pr_warn("%s: Medion Quadro, no ISL6405 found !\n",
__func__);
goto detach_frontend;
}
if (dev_id == 0x07) {
/* fire up the 2nd section of the LNB supply since
we can't do this from the other section */
msg.buf = &data;
i2c_transfer(&dev->i2c_adap, &msg, 1);
}
fe->ops.i2c_gate_ctrl(fe, 0);
dev->original_set_voltage = fe->ops.set_voltage;
fe->ops.set_voltage = md8800_set_voltage;
dev->original_set_high_voltage = fe->ops.enable_high_lnb_voltage;
fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage;
} else {
fe->ops.set_voltage = md8800_set_voltage2;
fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage2;
}
}
}
break;
case SAA7134_BOARD_AVERMEDIA_AVERTVHD_A180:
fe0->dvb.frontend = dvb_attach(nxt200x_attach, &avertvhda180,
&dev->i2c_adap);
if (fe0->dvb.frontend)
dvb_attach(dvb_pll_attach, fe0->dvb.frontend, 0x61,
NULL, DVB_PLL_TDHU2);
break;
case SAA7134_BOARD_ADS_INSTANT_HDTV_PCI:
case SAA7134_BOARD_KWORLD_ATSC110:
fe0->dvb.frontend = dvb_attach(nxt200x_attach, &kworldatsc110,
&dev->i2c_adap);
if (fe0->dvb.frontend)
dvb_attach(simple_tuner_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x61,
TUNER_PHILIPS_TUV1236D);
break;
case SAA7134_BOARD_KWORLD_PC150U:
saa7134_set_gpio(dev, 18, 1); /* Switch to digital mode */
saa7134_tuner_callback(dev, 0,
TDA18271_CALLBACK_CMD_AGC_ENABLE, 1);
fe0->dvb.frontend = dvb_attach(s5h1411_attach,
&kworld_s5h1411_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&kworld_pc150u_tda18271_config);
}
break;
case SAA7134_BOARD_FLYDVBS_LR300:
fe0->dvb.frontend = dvb_attach(tda10086_attach, &flydvbs,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda826x_attach, fe0->dvb.frontend, 0x60,
&dev->i2c_adap, 0) == NULL) {
pr_warn("%s: No tda826x found!\n", __func__);
goto detach_frontend;
}
if (dvb_attach(isl6421_attach, fe0->dvb.frontend,
&dev->i2c_adap,
0x08, 0, 0, false) == NULL) {
pr_warn("%s: No ISL6421 found!\n", __func__);
goto detach_frontend;
}
}
break;
case SAA7134_BOARD_ASUS_EUROPA2_HYBRID:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&medion_cardbus,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dev->original_demod_sleep = fe0->dvb.frontend->ops.sleep;
fe0->dvb.frontend->ops.sleep = philips_europa_demod_sleep;
dvb_attach(simple_tuner_attach, fe0->dvb.frontend,
&dev->i2c_adap, medion_cardbus.tuner_address,
TUNER_PHILIPS_FMD1216ME_MK3);
}
break;
case SAA7134_BOARD_VIDEOMATE_DVBT_200A:
fe0->dvb.frontend = dvb_attach(tda10046_attach,
&philips_europa_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
fe0->dvb.frontend->ops.tuner_ops.init = philips_td1316_tuner_init;
fe0->dvb.frontend->ops.tuner_ops.set_params = philips_td1316_tuner_set_params;
}
break;
case SAA7134_BOARD_CINERGY_HT_PCMCIA:
if (configure_tda827x_fe(dev, &cinergy_ht_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_CINERGY_HT_PCI:
if (configure_tda827x_fe(dev, &cinergy_ht_pci_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_PHILIPS_TIGER_S:
if (configure_tda827x_fe(dev, &philips_tiger_s_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_ASUS_P7131_4871:
if (configure_tda827x_fe(dev, &asus_p7131_4871_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_ASUSTeK_P7131_HYBRID_LNA:
if (configure_tda827x_fe(dev, &asus_p7131_hybrid_lna_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_AVERMEDIA_SUPER_007:
if (configure_tda827x_fe(dev, &avermedia_super_007_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_TWINHAN_DTV_DVB_3056:
if (configure_tda827x_fe(dev, &twinhan_dtv_dvb_3056_config,
&tda827x_cfg_2_sw42) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_PHILIPS_SNAKE:
fe0->dvb.frontend = dvb_attach(tda10086_attach, &flydvbs,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda826x_attach, fe0->dvb.frontend, 0x60,
&dev->i2c_adap, 0) == NULL) {
pr_warn("%s: No tda826x found!\n", __func__);
goto detach_frontend;
}
if (dvb_attach(lnbp21_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0, 0) == NULL) {
pr_warn("%s: No lnbp21 found!\n", __func__);
goto detach_frontend;
}
}
break;
case SAA7134_BOARD_CREATIX_CTX953:
if (configure_tda827x_fe(dev, &md8800_dvbt_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_MSI_TVANYWHERE_AD11:
if (configure_tda827x_fe(dev, &philips_tiger_s_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_AVERMEDIA_CARDBUS_506:
pr_debug("AverMedia E506R dvb setup\n");
saa7134_set_gpio(dev, 25, 0);
msleep(10);
saa7134_set_gpio(dev, 25, 1);
fe0->dvb.frontend = dvb_attach(mt352_attach,
&avermedia_xc3028_mt352_dev,
&dev->i2c_adap);
attach_xc3028 = 1;
break;
case SAA7134_BOARD_MD7134_BRIDGE_2:
fe0->dvb.frontend = dvb_attach(tda10086_attach,
&sd1878_4m, &dev->i2c_adap);
if (fe0->dvb.frontend) {
struct dvb_frontend *fe;
if (dvb_attach(dvb_pll_attach, fe0->dvb.frontend, 0x60,
&dev->i2c_adap, DVB_PLL_PHILIPS_SD1878_TDA8261) == NULL) {
pr_warn("%s: MD7134 DVB-S, no SD1878 found !\n",
__func__);
goto detach_frontend;
}
/* we need to open the i2c gate (we know it exists) */
fe = fe0->dvb.frontend;
fe->ops.i2c_gate_ctrl(fe, 1);
if (dvb_attach(isl6405_attach, fe,
&dev->i2c_adap, 0x08, 0, 0) == NULL) {
pr_warn("%s: MD7134 DVB-S, no ISL6405 found !\n",
__func__);
goto detach_frontend;
}
fe->ops.i2c_gate_ctrl(fe, 0);
dev->original_set_voltage = fe->ops.set_voltage;
fe->ops.set_voltage = md8800_set_voltage;
dev->original_set_high_voltage = fe->ops.enable_high_lnb_voltage;
fe->ops.enable_high_lnb_voltage = md8800_set_high_voltage;
}
break;
case SAA7134_BOARD_AVERMEDIA_M103:
saa7134_set_gpio(dev, 25, 0);
msleep(10);
saa7134_set_gpio(dev, 25, 1);
fe0->dvb.frontend = dvb_attach(mt352_attach,
&avermedia_xc3028_mt352_dev,
&dev->i2c_adap);
attach_xc3028 = 1;
break;
case SAA7134_BOARD_ASUSTeK_TIGER_3IN1:
if (!use_frontend) { /* terrestrial */
if (configure_tda827x_fe(dev, &asus_tiger_3in1_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
} else { /* satellite */
fe0->dvb.frontend = dvb_attach(tda10086_attach,
&flydvbs, &dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda826x_attach,
fe0->dvb.frontend, 0x60,
&dev->i2c_adap, 0) == NULL) {
pr_warn("%s: Asus Tiger 3in1, no tda826x found!\n",
__func__);
goto detach_frontend;
}
if (dvb_attach(lnbp21_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0, 0) == NULL) {
pr_warn("%s: Asus Tiger 3in1, no lnbp21 found!\n",
__func__);
goto detach_frontend;
}
}
}
break;
case SAA7134_BOARD_ASUSTeK_PS3_100:
if (!use_frontend) { /* terrestrial */
if (configure_tda827x_fe(dev, &asus_ps3_100_config,
&tda827x_cfg_2) < 0)
goto detach_frontend;
} else { /* satellite */
fe0->dvb.frontend = dvb_attach(tda10086_attach,
&flydvbs, &dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(tda826x_attach,
fe0->dvb.frontend, 0x60,
&dev->i2c_adap, 0) == NULL) {
pr_warn("%s: Asus My Cinema PS3-100, no tda826x found!\n",
__func__);
goto detach_frontend;
}
if (dvb_attach(lnbp21_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0, 0) == NULL) {
pr_warn("%s: Asus My Cinema PS3-100, no lnbp21 found!\n",
__func__);
goto detach_frontend;
}
}
}
break;
case SAA7134_BOARD_ASUSTeK_TIGER:
if (configure_tda827x_fe(dev, &philips_tiger_config,
&tda827x_cfg_0) < 0)
goto detach_frontend;
break;
case SAA7134_BOARD_BEHOLD_H6:
fe0->dvb.frontend = dvb_attach(zl10353_attach,
&behold_h6_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dvb_attach(simple_tuner_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x61,
TUNER_PHILIPS_FMD1216MEX_MK3);
}
break;
case SAA7134_BOARD_BEHOLD_X7:
fe0->dvb.frontend = dvb_attach(zl10353_attach,
&behold_x7_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dvb_attach(xc5000_attach, fe0->dvb.frontend,
&dev->i2c_adap, &behold_x7_tunerconfig);
}
break;
case SAA7134_BOARD_BEHOLD_H7:
fe0->dvb.frontend = dvb_attach(zl10353_attach,
&behold_x7_config,
&dev->i2c_adap);
if (fe0->dvb.frontend) {
dvb_attach(xc5000_attach, fe0->dvb.frontend,
&dev->i2c_adap, &behold_x7_tunerconfig);
}
break;
case SAA7134_BOARD_AVERMEDIA_A700_PRO:
case SAA7134_BOARD_AVERMEDIA_A700_HYBRID:
/* Zarlink ZL10313 */
fe0->dvb.frontend = dvb_attach(mt312_attach,
&avertv_a700_mt312, &dev->i2c_adap);
if (fe0->dvb.frontend) {
if (dvb_attach(zl10036_attach, fe0->dvb.frontend,
&avertv_a700_tuner, &dev->i2c_adap) == NULL) {
pr_warn("%s: No zl10036 found!\n",
__func__);
}
}
break;
case SAA7134_BOARD_VIDEOMATE_S350:
fe0->dvb.frontend = dvb_attach(mt312_attach,
&zl10313_compro_s350_config, &dev->i2c_adap);
if (fe0->dvb.frontend)
if (dvb_attach(zl10039_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap) == NULL)
pr_warn("%s: No zl10039 found!\n",
__func__);
break;
case SAA7134_BOARD_VIDEOMATE_T750:
fe0->dvb.frontend = dvb_attach(zl10353_attach,
&videomate_t750_zl10353_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
if (dvb_attach(qt1010_attach,
fe0->dvb.frontend,
&dev->i2c_adap,
&videomate_t750_qt1010_config) == NULL)
pr_warn("error attaching QT1010\n");
}
break;
case SAA7134_BOARD_ZOLID_HYBRID_PCI:
fe0->dvb.frontend = dvb_attach(tda10048_attach,
&zolid_tda10048_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&zolid_tda18271_config);
}
break;
case SAA7134_BOARD_LEADTEK_WINFAST_DTV1000S:
fe0->dvb.frontend = dvb_attach(tda10048_attach,
&dtv1000s_tda10048_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&dtv1000s_tda18271_config);
}
break;
case SAA7134_BOARD_KWORLD_PCI_SBTVD_FULLSEG:
/* Switch to digital mode */
saa7134_tuner_callback(dev, 0,
TDA18271_CALLBACK_CMD_AGC_ENABLE, 1);
fe0->dvb.frontend = dvb_attach(mb86a20s_attach,
&kworld_mb86a20s_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
fe0->dvb.frontend->ops.i2c_gate_ctrl = kworld_sbtvd_gate_ctrl;
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&kworld_tda18271_config);
}
/* mb86a20s need to use the I2C gateway */
break;
case SAA7134_BOARD_MAGICPRO_PROHDTV_PRO2:
fe0->dvb.frontend = dvb_attach(lgs8gxx_attach,
&prohdtv_pro2_lgs8g75_config,
&dev->i2c_adap);
if (fe0->dvb.frontend != NULL) {
dvb_attach(tda829x_attach, fe0->dvb.frontend,
&dev->i2c_adap, 0x4b,
&tda829x_no_probe);
dvb_attach(tda18271_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap,
&prohdtv_pro2_tda18271_config);
}
break;
case SAA7134_BOARD_AVERMEDIA_A706:
/* Enable all DVB-S devices now */
/* CE5039 DVB-S tuner SLEEP pin low */
saa7134_set_gpio(dev, 23, 0);
/* CE6313 DVB-S demod SLEEP pin low */
saa7134_set_gpio(dev, 9, 0);
/* CE6313 DVB-S demod RESET# pin high */
saa7134_set_gpio(dev, 25, 1);
msleep(1);
fe0->dvb.frontend = dvb_attach(mt312_attach,
&zl10313_avermedia_a706_config, &dev->i2c_adap);
if (fe0->dvb.frontend) {
fe0->dvb.frontend->ops.i2c_gate_ctrl = NULL;
if (dvb_attach(zl10039_attach, fe0->dvb.frontend,
0x60, &dev->i2c_adap) == NULL)
pr_warn("%s: No zl10039 found!\n",
__func__);
}
break;
default:
pr_warn("Huh? unknown DVB card?\n");
break;
}
if (attach_xc3028) {
struct dvb_frontend *fe;
struct xc2028_config cfg = {
.i2c_adap = &dev->i2c_adap,
.i2c_addr = 0x61,
};
if (!fe0->dvb.frontend)
goto detach_frontend;
fe = dvb_attach(xc2028_attach, fe0->dvb.frontend, &cfg);
if (!fe) {
pr_err("%s/2: xc3028 attach failed\n",
dev->name);
goto detach_frontend;
}
}
if (NULL == fe0->dvb.frontend) {
pr_err("%s/dvb: frontend initialization failed\n", dev->name);
goto detach_frontend;
}
/* define general-purpose callback pointer */
fe0->dvb.frontend->callback = saa7134_tuner_callback;
/* register everything else */
#ifndef CONFIG_MEDIA_CONTROLLER_DVB
ret = vb2_dvb_register_bus(&dev->frontends, THIS_MODULE, dev,
&dev->pci->dev, NULL,
adapter_nr, 0);
#else
ret = vb2_dvb_register_bus(&dev->frontends, THIS_MODULE, dev,
&dev->pci->dev, dev->media_dev,
adapter_nr, 0);
#endif
/* this sequence is necessary to make the tda1004x load its firmware
* and to enter analog mode of hybrid boards
*/
if (!ret) {
if (fe0->dvb.frontend->ops.init)
fe0->dvb.frontend->ops.init(fe0->dvb.frontend);
if (fe0->dvb.frontend->ops.sleep)
fe0->dvb.frontend->ops.sleep(fe0->dvb.frontend);
if (fe0->dvb.frontend->ops.tuner_ops.sleep)
fe0->dvb.frontend->ops.tuner_ops.sleep(fe0->dvb.frontend);
}
return ret;
detach_frontend:
vb2_dvb_dealloc_frontends(&dev->frontends);
vb2_queue_release(&fe0->dvb.dvbq);
return -EINVAL;
}
static int dvb_fini(struct saa7134_dev *dev)
{
struct vb2_dvb_frontend *fe0;
/* Get the first frontend */
fe0 = vb2_dvb_get_frontend(&dev->frontends, 1);
if (!fe0)
return -EINVAL;
/* FIXME: I suspect that this code is bogus, since the entry for
Pinnacle 300I DVB-T PAL already defines the proper init to allow
the detection of mt2032 (TDA9887_PORT2_INACTIVE)
*/
if (dev->board == SAA7134_BOARD_PINNACLE_300I_DVBT_PAL) {
struct v4l2_priv_tun_config tda9887_cfg;
static int on = TDA9887_PRESENT | TDA9887_PORT2_INACTIVE;
tda9887_cfg.tuner = TUNER_TDA9887;
tda9887_cfg.priv = &on;
/* otherwise we don't detect the tuner on next insmod */
saa_call_all(dev, tuner, s_config, &tda9887_cfg);
} else if (dev->board == SAA7134_BOARD_MEDION_MD8800_QUADRO) {
if ((dev->eedata[2] == 0x07) && use_frontend) {
/* turn off the 2nd lnb supply */
u8 data = 0x80;
struct i2c_msg msg = {.addr = 0x08, .buf = &data, .flags = 0, .len = 1};
struct dvb_frontend *fe;
fe = fe0->dvb.frontend;
if (fe->ops.i2c_gate_ctrl) {
fe->ops.i2c_gate_ctrl(fe, 1);
i2c_transfer(&dev->i2c_adap, &msg, 1);
fe->ops.i2c_gate_ctrl(fe, 0);
}
}
}
vb2_dvb_unregister_bus(&dev->frontends);
vb2_queue_release(&fe0->dvb.dvbq);
return 0;
}
static struct saa7134_mpeg_ops dvb_ops = {
.type = SAA7134_MPEG_DVB,
.init = dvb_init,
.fini = dvb_fini,
};
static int __init dvb_register(void)
{
return saa7134_ts_register(&dvb_ops);
}
static void __exit dvb_unregister(void)
{
saa7134_ts_unregister(&dvb_ops);
}
module_init(dvb_register);
module_exit(dvb_unregister);
Reference in a new issue View git blame Copy permalink