mirrors/linux-stable
1
0
Fork 0
mirror of https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git synced 2024-09-12 05:48:40 +00:00
Code Issues Releases Wiki Activity
linux-stable/arch/arm/mach-omap2/pm24xx.c
Tony Lindgren b764a5863f gpio: omap: Remove custom PM calls and use cpu_pm instead 
For a long time the gpio-omap custom PM calls have been annoying me so
let's replace them with cpu_pm instead. This will enable GPIO PM for
deeper idle states on omap4. And we can handle GPIO PM for omap2/3/4
in the same way.

Note that with this patch we are also slightly changing GPIO PM to be
less aggressive for omap3 and only will idle GPIO when PER context
may be lost.

For omap2, we don't need to save context and don't want to remove any
triggering so let's add a quirk flag for that.

Let's do this all in a single patch to avoid a situation where old
custom calls still are used with new code.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-24 14:24:44 +02:00

317 lines
7.9 KiB
C
Raw Blame History

/*
* OMAP2 Power Management Routines
*
* Copyright (C) 2005 Texas Instruments, Inc.
* Copyright (C) 2006-2008 Nokia Corporation
*
* Written by:
* Richard Woodruff <r-woodruff2@ti.com>
* Tony Lindgren
* Juha Yrjola
* Amit Kucheria <amit.kucheria@nokia.com>
* Igor Stoppa <igor.stoppa@nokia.com>
*
* Based on pm.c for omap1
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/cpu_pm.h>
#include <linux/suspend.h>
#include <linux/sched.h>
#include <linux/proc_fs.h>
#include <linux/interrupt.h>
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/irq.h>
#include <linux/time.h>
#include <asm/fncpy.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <asm/mach-types.h>
#include <asm/system_misc.h>
#include <linux/omap-dma.h>
#include "soc.h"
#include "common.h"
#include "clock.h"
#include "prm2xxx.h"
#include "prm-regbits-24xx.h"
#include "cm2xxx.h"
#include "cm-regbits-24xx.h"
#include "sdrc.h"
#include "sram.h"
#include "pm.h"
#include "control.h"
#include "powerdomain.h"
#include "clockdomain.h"
static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
void __iomem *sdrc_power);
static struct powerdomain *mpu_pwrdm, *core_pwrdm;
static struct clockdomain *dsp_clkdm, *mpu_clkdm, *wkup_clkdm, *gfx_clkdm;
static struct clk *osc_ck, *emul_ck;
static int omap2_enter_full_retention(void)
{
u32 l;
/* There is 1 reference hold for all children of the oscillator
* clock, the following will remove it. If no one else uses the
* oscillator itself it will be disabled if/when we enter retention
* mode.
*/
clk_disable(osc_ck);
/* Clear old wake-up events */
/* REVISIT: These write to reserved bits? */
omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
/* Workaround to kill USB */
l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
cpu_cluster_pm_enter();
/* One last check for pending IRQs to avoid extra latency due
* to sleeping unnecessarily. */
if (omap_irq_pending())
goto no_sleep;
/* Jump to SRAM suspend code */
omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
OMAP_SDRC_REGADDR(SDRC_POWER));
no_sleep:
cpu_cluster_pm_exit();
clk_enable(osc_ck);
/* clear CORE wake-up events */
omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
/* wakeup domain events - bit 1: GPT1, bit5 GPIO */
omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, 0x4 | 0x1);
/* MPU domain wake events */
omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x1);
omap_prm_clear_mod_irqs(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET, 0x20);
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_ON);
return 0;
}
static int sti_console_enabled;
static int omap2_allow_mpu_retention(void)
{
if (!omap2xxx_cm_mpu_retention_allowed())
return 0;
if (sti_console_enabled)
return 0;
return 1;
}
static void omap2_enter_mpu_retention(void)
{
const int zero = 0;
/* The peripherals seem not to be able to wake up the MPU when
* it is in retention mode. */
if (omap2_allow_mpu_retention()) {
/* REVISIT: These write to reserved bits? */
omap_prm_clear_mod_irqs(CORE_MOD, PM_WKST1, ~0);
omap_prm_clear_mod_irqs(CORE_MOD, OMAP24XX_PM_WKST2, ~0);
omap_prm_clear_mod_irqs(WKUP_MOD, PM_WKST, ~0);
/* Try to enter MPU retention */
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
} else {
/* Block MPU retention */
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
}
/* WFI */
asm("mcr p15, 0, %0, c7, c0, 4" : : "r" (zero) : "memory", "cc");
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
}
static int omap2_can_sleep(void)
{
if (omap2xxx_cm_fclks_active())
return 0;
if (__clk_is_enabled(osc_ck))
return 0;
if (omap_dma_running())
return 0;
return 1;
}
static void omap2_pm_idle(void)
{
if (!omap2_can_sleep()) {
if (omap_irq_pending())
return;
omap2_enter_mpu_retention();
return;
}
if (omap_irq_pending())
return;
omap2_enter_full_retention();
}
static void __init prcm_setup_regs(void)
{
int i, num_mem_banks;
struct powerdomain *pwrdm;
/*
* Enable autoidle
* XXX This should be handled by hwmod code or PRCM init code
*/
omap2_prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
OMAP2_PRCM_SYSCONFIG_OFFSET);
/*
* Set CORE powerdomain memory banks to retain their contents
* during RETENTION
*/
num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
for (i = 0; i < num_mem_banks; i++)
pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
pwrdm_set_logic_retst(core_pwrdm, PWRDM_POWER_RET);
pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
/* Force-power down DSP, GFX powerdomains */
pwrdm = clkdm_get_pwrdm(dsp_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
pwrdm = clkdm_get_pwrdm(gfx_clkdm);
pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
/* Enable hardware-supervised idle for all clkdms */
clkdm_for_each(omap_pm_clkdms_setup, NULL);
clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
omap_common_suspend_init(omap2_enter_full_retention);
/* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
* stabilisation */
omap2_prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSSETUP_OFFSET);
/* Configure automatic voltage transition */
omap2_prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
OMAP2_PRCM_VOLTSETUP_OFFSET);
omap2_prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
(0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
OMAP24XX_MEMRETCTRL_MASK |
(0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
(0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
/* Enable wake-up events */
omap2_prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
WKUP_MOD, PM_WKEN);
/* Enable SYS_CLKEN control when all domains idle */
omap2_prm_set_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK, OMAP24XX_GR_MOD,
OMAP2_PRCM_CLKSRC_CTRL_OFFSET);
}
int __init omap2_pm_init(void)
{
u32 l;
printk(KERN_INFO "Power Management for OMAP2 initializing\n");
l = omap2_prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
/* Look up important powerdomains */
mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
if (!mpu_pwrdm)
pr_err("PM: mpu_pwrdm not found\n");
core_pwrdm = pwrdm_lookup("core_pwrdm");
if (!core_pwrdm)
pr_err("PM: core_pwrdm not found\n");
/* Look up important clockdomains */
mpu_clkdm = clkdm_lookup("mpu_clkdm");
if (!mpu_clkdm)
pr_err("PM: mpu_clkdm not found\n");
wkup_clkdm = clkdm_lookup("wkup_clkdm");
if (!wkup_clkdm)
pr_err("PM: wkup_clkdm not found\n");
dsp_clkdm = clkdm_lookup("dsp_clkdm");
if (!dsp_clkdm)
pr_err("PM: dsp_clkdm not found\n");
gfx_clkdm = clkdm_lookup("gfx_clkdm");
if (!gfx_clkdm)
pr_err("PM: gfx_clkdm not found\n");
osc_ck = clk_get(NULL, "osc_ck");
if (IS_ERR(osc_ck)) {
printk(KERN_ERR "could not get osc_ck\n");
return -ENODEV;
}
if (cpu_is_omap242x()) {
emul_ck = clk_get(NULL, "emul_ck");
if (IS_ERR(emul_ck)) {
printk(KERN_ERR "could not get emul_ck\n");
clk_put(osc_ck);
return -ENODEV;
}
}
prcm_setup_regs();
/*
* We copy the assembler sleep/wakeup routines to SRAM.
* These routines need to be in SRAM as that's the only
* memory the MPU can see when it wakes up after the entire
* chip enters idle.
*/
omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
omap24xx_cpu_suspend_sz);
arm_pm_idle = omap2_pm_idle;
return 0;
}
Reference in a new issue View git blame Copy permalink