195 lines
7.8 KiB
ReStructuredText
195 lines
7.8 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0
|
|
.. include:: <isonum.txt>
|
|
|
|
=======================
|
|
DPAA2 MAC / PHY support
|
|
=======================
|
|
|
|
:Copyright: |copy| 2019 NXP
|
|
|
|
Overview
|
|
--------
|
|
|
|
The DPAA2 MAC / PHY support consists of a set of APIs that help DPAA2 network
|
|
drivers (dpaa2-eth, dpaa2-ethsw) interact with the PHY library.
|
|
|
|
DPAA2 Software Architecture
|
|
---------------------------
|
|
|
|
Among other DPAA2 objects, the fsl-mc bus exports DPNI objects (abstracting a
|
|
network interface) and DPMAC objects (abstracting a MAC). The dpaa2-eth driver
|
|
probes on the DPNI object and connects to and configures a DPMAC object with
|
|
the help of phylink.
|
|
|
|
Data connections may be established between a DPNI and a DPMAC, or between two
|
|
DPNIs. Depending on the connection type, the netif_carrier_[on/off] is handled
|
|
directly by the dpaa2-eth driver or by phylink.
|
|
|
|
.. code-block:: none
|
|
|
|
Sources of abstracted link state information presented by the MC firmware
|
|
|
|
+--------------------------------------+
|
|
+------------+ +---------+ | xgmac_mdio |
|
|
| net_device | | phylink |--| +-----+ +-----+ +-----+ +-----+ |
|
|
+------------+ +---------+ | | PHY | | PHY | | PHY | | PHY | |
|
|
| | | +-----+ +-----+ +-----+ +-----+ |
|
|
+------------------------------------+ | External MDIO bus |
|
|
| dpaa2-eth | +--------------------------------------+
|
|
+------------------------------------+
|
|
| | Linux
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
| | MC firmware
|
|
| /| V
|
|
+----------+ / | +----------+
|
|
| | / | | |
|
|
| | | | | |
|
|
| DPNI |<------| |<------| DPMAC |
|
|
| | | | | |
|
|
| | \ |<---+ | |
|
|
+----------+ \ | | +----------+
|
|
\| |
|
|
|
|
|
+--------------------------------------+
|
|
| MC firmware polling MAC PCS for link |
|
|
| +-----+ +-----+ +-----+ +-----+ |
|
|
| | PCS | | PCS | | PCS | | PCS | |
|
|
| +-----+ +-----+ +-----+ +-----+ |
|
|
| Internal MDIO bus |
|
|
+--------------------------------------+
|
|
|
|
|
|
Depending on an MC firmware configuration setting, each MAC may be in one of two modes:
|
|
|
|
- DPMAC_LINK_TYPE_FIXED: the link state management is handled exclusively by
|
|
the MC firmware by polling the MAC PCS. Without the need to register a
|
|
phylink instance, the dpaa2-eth driver will not bind to the connected dpmac
|
|
object at all.
|
|
|
|
- DPMAC_LINK_TYPE_PHY: The MC firmware is left waiting for link state update
|
|
events, but those are in fact passed strictly between the dpaa2-mac (based on
|
|
phylink) and its attached net_device driver (dpaa2-eth, dpaa2-ethsw),
|
|
effectively bypassing the firmware.
|
|
|
|
Implementation
|
|
--------------
|
|
|
|
At probe time or when a DPNI's endpoint is dynamically changed, the dpaa2-eth
|
|
is responsible to find out if the peer object is a DPMAC and if this is the
|
|
case, to integrate it with PHYLINK using the dpaa2_mac_connect() API, which
|
|
will do the following:
|
|
|
|
- look up the device tree for PHYLINK-compatible of binding (phy-handle)
|
|
- will create a PHYLINK instance associated with the received net_device
|
|
- connect to the PHY using phylink_of_phy_connect()
|
|
|
|
The following phylink_mac_ops callback are implemented:
|
|
|
|
- .validate() will populate the supported linkmodes with the MAC capabilities
|
|
only when the phy_interface_t is RGMII_* (at the moment, this is the only
|
|
link type supported by the driver).
|
|
|
|
- .mac_config() will configure the MAC in the new configuration using the
|
|
dpmac_set_link_state() MC firmware API.
|
|
|
|
- .mac_link_up() / .mac_link_down() will update the MAC link using the same
|
|
API described above.
|
|
|
|
At driver unbind() or when the DPNI object is disconnected from the DPMAC, the
|
|
dpaa2-eth driver calls dpaa2_mac_disconnect() which will, in turn, disconnect
|
|
from the PHY and destroy the PHYLINK instance.
|
|
|
|
In case of a DPNI-DPMAC connection, an 'ip link set dev eth0 up' would start
|
|
the following sequence of operations:
|
|
|
|
(1) phylink_start() called from .dev_open().
|
|
(2) The .mac_config() and .mac_link_up() callbacks are called by PHYLINK.
|
|
(3) In order to configure the HW MAC, the MC Firmware API
|
|
dpmac_set_link_state() is called.
|
|
(4) The firmware will eventually setup the HW MAC in the new configuration.
|
|
(5) A netif_carrier_on() call is made directly from PHYLINK on the associated
|
|
net_device.
|
|
(6) The dpaa2-eth driver handles the LINK_STATE_CHANGE irq in order to
|
|
enable/disable Rx taildrop based on the pause frame settings.
|
|
|
|
.. code-block:: none
|
|
|
|
+---------+ +---------+
|
|
| PHYLINK |-------------->| eth0 |
|
|
+---------+ (5) +---------+
|
|
(1) ^ |
|
|
| |
|
|
| v (2)
|
|
+-----------------------------------+
|
|
| dpaa2-eth |
|
|
+-----------------------------------+
|
|
| ^ (6)
|
|
| |
|
|
v (3) |
|
|
+---------+---------------+---------+
|
|
| DPMAC | | DPNI |
|
|
+---------+ +---------+
|
|
| MC Firmware |
|
|
+-----------------------------------+
|
|
|
|
|
|
|
|
v (4)
|
|
+-----------------------------------+
|
|
| HW MAC |
|
|
+-----------------------------------+
|
|
|
|
In case of a DPNI-DPNI connection, a usual sequence of operations looks like
|
|
the following:
|
|
|
|
(1) ip link set dev eth0 up
|
|
(2) The dpni_enable() MC API called on the associated fsl_mc_device.
|
|
(3) ip link set dev eth1 up
|
|
(4) The dpni_enable() MC API called on the associated fsl_mc_device.
|
|
(5) The LINK_STATE_CHANGED irq is received by both instances of the dpaa2-eth
|
|
driver because now the operational link state is up.
|
|
(6) The netif_carrier_on() is called on the exported net_device from
|
|
link_state_update().
|
|
|
|
.. code-block:: none
|
|
|
|
+---------+ +---------+
|
|
| eth0 | | eth1 |
|
|
+---------+ +---------+
|
|
| ^ ^ |
|
|
| | | |
|
|
(1) v | (6) (6) | v (3)
|
|
+---------+ +---------+
|
|
|dpaa2-eth| |dpaa2-eth|
|
|
+---------+ +---------+
|
|
| ^ ^ |
|
|
| | | |
|
|
(2) v | (5) (5) | v (4)
|
|
+---------+---------------+---------+
|
|
| DPNI | | DPNI |
|
|
+---------+ +---------+
|
|
| MC Firmware |
|
|
+-----------------------------------+
|
|
|
|
|
|
Exported API
|
|
------------
|
|
|
|
Any DPAA2 driver that drivers endpoints of DPMAC objects should service its
|
|
_EVENT_ENDPOINT_CHANGED irq and connect/disconnect from the associated DPMAC
|
|
when necessary using the below listed API::
|
|
|
|
- int dpaa2_mac_connect(struct dpaa2_mac *mac);
|
|
- void dpaa2_mac_disconnect(struct dpaa2_mac *mac);
|
|
|
|
A phylink integration is necessary only when the partner DPMAC is not of
|
|
``TYPE_FIXED``. This means it is either of ``TYPE_PHY``, or of
|
|
``TYPE_BACKPLANE`` (the difference being the two that in the ``TYPE_BACKPLANE``
|
|
mode, the MC firmware does not access the PCS registers). One can check for
|
|
this condition using the following helper::
|
|
|
|
- static inline bool dpaa2_mac_is_type_phy(struct dpaa2_mac *mac);
|
|
|
|
Before connection to a MAC, the caller must allocate and populate the
|
|
dpaa2_mac structure with the associated net_device, a pointer to the MC portal
|
|
to be used and the actual fsl_mc_device structure of the DPMAC.
|