linux-stable/arch/arm/mach-omap2/sleep24xx.S
Paul Walmsley 088e8806c4 ARM: OMAP2xxx: PM: enter WFI via inline asm if CORE stays active
There shouldn't be any need to jump to SRAM code if the OMAP CORE
clockdomain (and consequently the SDRAM controller and CORE PLL) stays
active during MPU WFI.  The SRAM code should only be needed when the RAM
enters self-refresh.  So in the case where CORE stays active, just call
WFI directly from the mach-omap2/pm24xx.c code.  This removes some
unnecessary SRAM code.

This second version replaces the inline WFI with the corresponding
coprocessor register call, using tlbflush.h as an example.  This is
because the assembler doesn't recognize WFI as a valid ARMv6
instruction.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2013-02-06 13:48:14 -07:00

105 lines
3.4 KiB
ArmAsm

/*
* linux/arch/arm/mach-omap2/sleep.S
*
* (C) Copyright 2004
* Texas Instruments, <www.ti.com>
* Richard Woodruff <r-woodruff2@ti.com>
*
* (C) Copyright 2006 Nokia Corporation
* Fixed idle loop sleep
* Igor Stoppa <igor.stoppa@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <linux/linkage.h>
#include <asm/assembler.h>
#include "omap24xx.h"
#include "sdrc.h"
/* First address of reserved address space? apparently valid for OMAP2 & 3 */
#define A_SDRC0_V (0xC0000000)
.text
/*
* omap24xx_cpu_suspend() - Forces OMAP into deep sleep state by completing
* SDRC shutdown then ARM shutdown. Upon wake MPU is back on so just restore
* SDRC.
*
* Input:
* R0 : DLL ctrl value pre-Sleep
* R1 : SDRC_DLLA_CTRL
* R2 : SDRC_POWER
*
* The if the DPLL is going to AutoIdle. It seems like the DPLL may be back on
* when we get called, but the DLL probably isn't. We will wait a bit more in
* case the DPLL isn't quite there yet. The code will wait on DLL for DDR even
* if in unlocked mode.
*
* For less than 242x-ES2.2 upon wake from a sleep mode where the external
* oscillator was stopped, a timing bug exists where a non-stabilized 12MHz
* clock can pass into the PRCM can cause problems at DSP and IVA.
* To work around this the code will switch to the 32kHz source prior to sleep.
* Post sleep we will shift back to using the DPLL. Apparently,
* CM_IDLEST_CLKGEN does not reflect the full clock change so you need to wait
* 3x12MHz + 3x32kHz clocks for a full switch.
*
* The DLL load value is not kept in RETENTION or OFF. It needs to be restored
* at wake
*/
.align 3
ENTRY(omap24xx_cpu_suspend)
stmfd sp!, {r0 - r12, lr} @ save registers on stack
mov r3, #0x0 @ clear for mcr call
mcr p15, 0, r3, c7, c10, 4 @ memory barrier, hope SDR/DDR finished
nop
nop
ldr r4, [r2] @ read SDRC_POWER
orr r4, r4, #0x40 @ enable self refresh on idle req
mov r5, #0x2000 @ set delay (DPLL relock + DLL relock)
str r4, [r2] @ make it so
nop
mcr p15, 0, r3, c7, c0, 4 @ wait for interrupt
nop
loop:
subs r5, r5, #0x1 @ awake, wait just a bit
bne loop
/* The DPLL has to be on before we take the DDR out of self refresh */
bic r4, r4, #0x40 @ now clear self refresh bit.
str r4, [r2] @ write to SDRC_POWER
ldr r4, A_SDRC0 @ make a clock happen
ldr r4, [r4] @ read A_SDRC0
nop @ start auto refresh only after clk ok
movs r0, r0 @ see if DDR or SDR
strne r0, [r1] @ rewrite DLLA to force DLL reload
addne r1, r1, #0x8 @ move to DLLB
strne r0, [r1] @ rewrite DLLB to force DLL reload
mov r5, #0x1000
loop2:
subs r5, r5, #0x1
bne loop2
/* resume*/
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
A_SDRC0:
.word A_SDRC0_V
ENTRY(omap24xx_cpu_suspend_sz)
.word . - omap24xx_cpu_suspend