linux-stable/arch/sh/boards/board-apsh4a3a.c

// SPDX-License-Identifier: GPL-2.0
/*
 * ALPHAPROJECT AP-SH4A-3A Support.
 *
 * Copyright (C) 2010 ALPHAPROJECT Co.,Ltd.
 * Copyright (C) 2008  Yoshihiro Shimoda
 * Copyright (C) 2009  Paul Mundt
 */
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/mtd/physmap.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/irq.h>
#include <linux/clk.h>
#include <asm/machvec.h>
#include <asm/sizes.h>
#include <asm/clock.h>

static struct mtd_partition nor_flash_partitions[] = {
	{
		.name		= "loader",
		.offset		= 0x00000000,
		.size		= 512 * 1024,
	},
	{
		.name		= "bootenv",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 512 * 1024,
	},
	{
		.name		= "kernel",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 4 * 1024 * 1024,
	},
	{
		.name		= "data",
		.offset		= MTDPART_OFS_APPEND,
		.size		= MTDPART_SIZ_FULL,
	},
};

static struct physmap_flash_data nor_flash_data = {
	.width		= 4,
	.parts		= nor_flash_partitions,
	.nr_parts	= ARRAY_SIZE(nor_flash_partitions),
};

static struct resource nor_flash_resources[] = {
	[0]	= {
		.start	= 0x00000000,
		.end	= 0x01000000 - 1,
		.flags	= IORESOURCE_MEM,
	}
};

static struct platform_device nor_flash_device = {
	.name		= "physmap-flash",
	.dev		= {
		.platform_data	= &nor_flash_data,
	},
	.num_resources	= ARRAY_SIZE(nor_flash_resources),
	.resource	= nor_flash_resources,
};

/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
	REGULATOR_SUPPLY("vddvario", "smsc911x"),
	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};

static struct resource smsc911x_resources[] = {
	[0] = {
		.name		= "smsc911x-memory",
		.start		= 0xA4000000,
		.end		= 0xA4000000 + SZ_256 - 1,
		.flags		= IORESOURCE_MEM,
	},
	[1] = {
		.name		= "smsc911x-irq",
		.start		= evt2irq(0x200),
		.end		= evt2irq(0x200),
		.flags		= IORESOURCE_IRQ,
	},
};

static struct smsc911x_platform_config smsc911x_config = {
	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
	.flags		= SMSC911X_USE_16BIT,
	.phy_interface	= PHY_INTERFACE_MODE_MII,
};

static struct platform_device smsc911x_device = {
	.name		= "smsc911x",
	.id		= -1,
	.num_resources	= ARRAY_SIZE(smsc911x_resources),
	.resource	= smsc911x_resources,
	.dev = {
		.platform_data = &smsc911x_config,
	},
};

static struct platform_device *apsh4a3a_devices[] __initdata = {
	&nor_flash_device,
	&smsc911x_device,
};

static int __init apsh4a3a_devices_setup(void)
{
	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));

	return platform_add_devices(apsh4a3a_devices,
				    ARRAY_SIZE(apsh4a3a_devices));
}
device_initcall(apsh4a3a_devices_setup);

static int apsh4a3a_clk_init(void)
{
	struct clk *clk;
	int ret;

	clk = clk_get(NULL, "extal");
	if (IS_ERR(clk))
		return PTR_ERR(clk);
	ret = clk_set_rate(clk, 33333000);
	clk_put(clk);

	return ret;
}

/* Initialize the board */
static void __init apsh4a3a_setup(char **cmdline_p)
{
	printk(KERN_INFO "Alpha Project AP-SH4A-3A support:\n");
}

static void __init apsh4a3a_init_irq(void)
{
	plat_irq_setup_pins(IRQ_MODE_IRQ7654);
}

/* Return the board specific boot mode pin configuration */
static int apsh4a3a_mode_pins(void)
{
	int value = 0;

	/* These are the factory default settings of SW1 and SW2.
	 * If you change these dip switches then you will need to
	 * adjust the values below as well.
	 */
	value &= ~MODE_PIN0;  /* Clock Mode 16 */
	value &= ~MODE_PIN1;
	value &= ~MODE_PIN2;
	value &= ~MODE_PIN3;
	value |=  MODE_PIN4;
	value &= ~MODE_PIN5;  /* 16-bit Area0 bus width */
	value |=  MODE_PIN6;  /* Area 0 SRAM interface */
	value |=  MODE_PIN7;
	value |=  MODE_PIN8;  /* Little Endian */
	value |=  MODE_PIN9;  /* Master Mode */
	value |=  MODE_PIN10; /* Crystal resonator */
	value |=  MODE_PIN11; /* Display Unit */
	value |=  MODE_PIN12;
	value &= ~MODE_PIN13; /* 29-bit address mode */
	value |=  MODE_PIN14; /* No PLL step-up */

	return value;
}

/*
 * The Machine Vector
 */
static struct sh_machine_vector mv_apsh4a3a __initmv = {
	.mv_name		= "AP-SH4A-3A",
	.mv_setup		= apsh4a3a_setup,
	.mv_clk_init		= apsh4a3a_clk_init,
	.mv_init_irq		= apsh4a3a_init_irq,
	.mv_mode_pins		= apsh4a3a_mode_pins,
};