linux-stable/drivers/power/pm2301_charger.c
Rupesh Kumar b64f51c4ad pm2301-charger: Wake device on register access
When USB  Dedicated or Standard host chargers are plugged into
the device, chargealg attempts to disable the PM2301 AC charger,
However, disabling PM2301 was failing because of it being in
runtime suepend mode & LPN pin being low.

Signed-off-by: Rupesh Kumar <rupesh.kumar@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
2013-03-07 12:35:57 +08:00

1259 lines
30 KiB
C

/*
* Copyright 2012 ST Ericsson.
*
* Power supply driver for ST Ericsson pm2xxx_charger charger
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/power_supply.h>
#include <linux/regulator/consumer.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/workqueue.h>
#include <linux/mfd/abx500/ab8500.h>
#include <linux/mfd/abx500/ab8500-bm.h>
#include <linux/mfd/abx500/ux500_chargalg.h>
#include <linux/pm2301_charger.h>
#include <linux/gpio.h>
#include <linux/pm_runtime.h>
#include "pm2301_charger.h"
#define to_pm2xxx_charger_ac_device_info(x) container_of((x), \
struct pm2xxx_charger, ac_chg)
#define SLEEP_MIN 50
#define SLEEP_MAX 100
#define PM2XXX_AUTOSUSPEND_DELAY 500
static int pm2xxx_interrupt_registers[] = {
PM2XXX_REG_INT1,
PM2XXX_REG_INT2,
PM2XXX_REG_INT3,
PM2XXX_REG_INT4,
PM2XXX_REG_INT5,
PM2XXX_REG_INT6,
};
static enum power_supply_property pm2xxx_charger_ac_props[] = {
POWER_SUPPLY_PROP_HEALTH,
POWER_SUPPLY_PROP_PRESENT,
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_VOLTAGE_AVG,
};
static int pm2xxx_charger_voltage_map[] = {
3500,
3525,
3550,
3575,
3600,
3625,
3650,
3675,
3700,
3725,
3750,
3775,
3800,
3825,
3850,
3875,
3900,
3925,
3950,
3975,
4000,
4025,
4050,
4075,
4100,
4125,
4150,
4175,
4200,
4225,
4250,
4275,
4300,
};
static int pm2xxx_charger_current_map[] = {
200,
200,
400,
600,
800,
1000,
1200,
1400,
1600,
1800,
2000,
2200,
2400,
2600,
2800,
3000,
};
static const struct i2c_device_id pm2xxx_ident[] = {
{ "pm2301", 0 },
{ }
};
static void set_lpn_pin(struct pm2xxx_charger *pm2)
{
if (!pm2->ac.charger_connected && gpio_is_valid(pm2->lpn_pin)) {
gpio_set_value(pm2->lpn_pin, 1);
usleep_range(SLEEP_MIN, SLEEP_MAX);
}
}
static void clear_lpn_pin(struct pm2xxx_charger *pm2)
{
if (!pm2->ac.charger_connected && gpio_is_valid(pm2->lpn_pin))
gpio_set_value(pm2->lpn_pin, 0);
}
static int pm2xxx_reg_read(struct pm2xxx_charger *pm2, int reg, u8 *val)
{
int ret;
/* wake up the device */
pm_runtime_get_sync(pm2->dev);
ret = i2c_smbus_read_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
1, val);
if (ret < 0)
dev_err(pm2->dev, "Error reading register at 0x%x\n", reg);
else
ret = 0;
return ret;
}
static int pm2xxx_reg_write(struct pm2xxx_charger *pm2, int reg, u8 val)
{
int ret;
/* wake up the device */
pm_runtime_get_sync(pm2->dev);
ret = i2c_smbus_write_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
1, &val);
if (ret < 0)
dev_err(pm2->dev, "Error writing register at 0x%x\n", reg);
else
ret = 0;
return ret;
}
static int pm2xxx_charging_enable_mngt(struct pm2xxx_charger *pm2)
{
int ret;
/* Enable charging */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
(PM2XXX_CH_AUTO_RESUME_EN | PM2XXX_CHARGER_ENA));
return ret;
}
static int pm2xxx_charging_disable_mngt(struct pm2xxx_charger *pm2)
{
int ret;
/* Disable SW EOC ctrl */
ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG, PM2XXX_SWCTRL_HW);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
return ret;
}
/* Disable charging */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
(PM2XXX_CH_AUTO_RESUME_DIS | PM2XXX_CHARGER_DIS));
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
return ret;
}
return 0;
}
static int pm2xxx_charger_batt_therm_mngt(struct pm2xxx_charger *pm2, int val)
{
queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
return 0;
}
int pm2xxx_charger_die_therm_mngt(struct pm2xxx_charger *pm2, int val)
{
queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
return 0;
}
static int pm2xxx_charger_ovv_mngt(struct pm2xxx_charger *pm2, int val)
{
dev_err(pm2->dev, "Overvoltage detected\n");
pm2->flags.ovv = true;
power_supply_changed(&pm2->ac_chg.psy);
/* Schedule a new HW failure check */
queue_delayed_work(pm2->charger_wq, &pm2->check_hw_failure_work, 0);
return 0;
}
static int pm2xxx_charger_wd_exp_mngt(struct pm2xxx_charger *pm2, int val)
{
dev_dbg(pm2->dev , "20 minutes watchdog occured\n");
pm2->ac.wd_expired = true;
power_supply_changed(&pm2->ac_chg.psy);
return 0;
}
static int pm2xxx_charger_vbat_lsig_mngt(struct pm2xxx_charger *pm2, int val)
{
int ret;
switch (val) {
case PM2XXX_INT1_ITVBATLOWR:
dev_dbg(pm2->dev, "VBAT grows above VBAT_LOW level\n");
/* Enable SW EOC ctrl */
ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG,
PM2XXX_SWCTRL_SW);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
return ret;
}
break;
case PM2XXX_INT1_ITVBATLOWF:
dev_dbg(pm2->dev, "VBAT drops below VBAT_LOW level\n");
/* Disable SW EOC ctrl */
ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG,
PM2XXX_SWCTRL_HW);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
return ret;
}
break;
default:
dev_err(pm2->dev, "Unknown VBAT level\n");
}
return 0;
}
static int pm2xxx_charger_bat_disc_mngt(struct pm2xxx_charger *pm2, int val)
{
dev_dbg(pm2->dev, "battery disconnected\n");
return 0;
}
static int pm2xxx_charger_detection(struct pm2xxx_charger *pm2, u8 *val)
{
int ret;
ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT2, val);
if (ret < 0) {
dev_err(pm2->dev, "Charger detection failed\n");
goto out;
}
*val &= (PM2XXX_INT2_S_ITVPWR1PLUG | PM2XXX_INT2_S_ITVPWR2PLUG);
out:
return ret;
}
static int pm2xxx_charger_itv_pwr_plug_mngt(struct pm2xxx_charger *pm2, int val)
{
int ret;
u8 read_val;
/*
* Since we can't be sure that the events are received
* synchronously, we have the check if the main charger is
* connected by reading the interrupt source register.
*/
ret = pm2xxx_charger_detection(pm2, &read_val);
if ((ret == 0) && read_val) {
pm2->ac.charger_connected = 1;
pm2->ac_conn = true;
queue_work(pm2->charger_wq, &pm2->ac_work);
}
return ret;
}
static int pm2xxx_charger_itv_pwr_unplug_mngt(struct pm2xxx_charger *pm2,
int val)
{
pm2->ac.charger_connected = 0;
queue_work(pm2->charger_wq, &pm2->ac_work);
return 0;
}
static int pm2_int_reg0(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & PM2XXX_INT1_ITVBATLOWR) {
ret = pm2xxx_charger_vbat_lsig_mngt(pm2,
PM2XXX_INT1_ITVBATLOWR);
if (ret < 0)
goto out;
}
if (val & PM2XXX_INT1_ITVBATLOWF) {
ret = pm2xxx_charger_vbat_lsig_mngt(pm2,
PM2XXX_INT1_ITVBATLOWF);
if (ret < 0)
goto out;
}
if (val & PM2XXX_INT1_ITVBATDISCONNECT) {
ret = pm2xxx_charger_bat_disc_mngt(pm2,
PM2XXX_INT1_ITVBATDISCONNECT);
if (ret < 0)
goto out;
}
out:
return ret;
}
static int pm2_int_reg1(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG)) {
dev_dbg(pm2->dev , "Main charger plugged\n");
ret = pm2xxx_charger_itv_pwr_plug_mngt(pm2, val &
(PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG));
}
if (val &
(PM2XXX_INT2_ITVPWR1UNPLUG | PM2XXX_INT2_ITVPWR2UNPLUG)) {
dev_dbg(pm2->dev , "Main charger unplugged\n");
ret = pm2xxx_charger_itv_pwr_unplug_mngt(pm2, val &
(PM2XXX_INT2_ITVPWR1UNPLUG |
PM2XXX_INT2_ITVPWR2UNPLUG));
}
return ret;
}
static int pm2_int_reg2(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & PM2XXX_INT3_ITAUTOTIMEOUTWD)
ret = pm2xxx_charger_wd_exp_mngt(pm2, val);
if (val & (PM2XXX_INT3_ITCHPRECHARGEWD |
PM2XXX_INT3_ITCHCCWD | PM2XXX_INT3_ITCHCVWD)) {
dev_dbg(pm2->dev,
"Watchdog occured for precharge, CC and CV charge\n");
}
return ret;
}
static int pm2_int_reg3(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT4_ITCHARGINGON)) {
dev_dbg(pm2->dev ,
"chargind operation has started\n");
}
if (val & (PM2XXX_INT4_ITVRESUME)) {
dev_dbg(pm2->dev,
"battery discharged down to VResume threshold\n");
}
if (val & (PM2XXX_INT4_ITBATTFULL)) {
dev_dbg(pm2->dev , "battery fully detected\n");
}
if (val & (PM2XXX_INT4_ITCVPHASE)) {
dev_dbg(pm2->dev, "CV phase enter with 0.5C charging\n");
}
if (val & (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV)) {
pm2->failure_case = VPWR_OVV;
ret = pm2xxx_charger_ovv_mngt(pm2, val &
(PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV));
dev_dbg(pm2->dev, "VPWR/VSYSTEM overvoltage detected\n");
}
if (val & (PM2XXX_INT4_S_ITBATTEMPCOLD |
PM2XXX_INT4_S_ITBATTEMPHOT)) {
ret = pm2xxx_charger_batt_therm_mngt(pm2, val &
(PM2XXX_INT4_S_ITBATTEMPCOLD |
PM2XXX_INT4_S_ITBATTEMPHOT));
dev_dbg(pm2->dev, "BTEMP is too Low/High\n");
}
return ret;
}
static int pm2_int_reg4(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & PM2XXX_INT5_ITVSYSTEMOVV) {
pm2->failure_case = VSYSTEM_OVV;
ret = pm2xxx_charger_ovv_mngt(pm2, val &
PM2XXX_INT5_ITVSYSTEMOVV);
dev_dbg(pm2->dev, "VSYSTEM overvoltage detected\n");
}
if (val & (PM2XXX_INT5_ITTHERMALWARNINGFALL |
PM2XXX_INT5_ITTHERMALWARNINGRISE |
PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
PM2XXX_INT5_ITTHERMALSHUTDOWNRISE)) {
dev_dbg(pm2->dev, "BTEMP die temperature is too Low/High\n");
ret = pm2xxx_charger_die_therm_mngt(pm2, val &
(PM2XXX_INT5_ITTHERMALWARNINGFALL |
PM2XXX_INT5_ITTHERMALWARNINGRISE |
PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
PM2XXX_INT5_ITTHERMALSHUTDOWNRISE));
}
return ret;
}
static int pm2_int_reg5(void *pm2_data, int val)
{
struct pm2xxx_charger *pm2 = pm2_data;
int ret = 0;
if (val & (PM2XXX_INT6_ITVPWR2DROP | PM2XXX_INT6_ITVPWR1DROP)) {
dev_dbg(pm2->dev, "VMPWR drop to VBAT level\n");
}
if (val & (PM2XXX_INT6_ITVPWR2VALIDRISE |
PM2XXX_INT6_ITVPWR1VALIDRISE |
PM2XXX_INT6_ITVPWR2VALIDFALL |
PM2XXX_INT6_ITVPWR1VALIDFALL)) {
dev_dbg(pm2->dev, "Falling/Rising edge on WPWR1/2\n");
}
return ret;
}
static irqreturn_t pm2xxx_irq_int(int irq, void *data)
{
struct pm2xxx_charger *pm2 = data;
struct pm2xxx_interrupts *interrupt = pm2->pm2_int;
int i;
/* wake up the device */
pm_runtime_get_sync(pm2->dev);
do {
for (i = 0; i < PM2XXX_NUM_INT_REG; i++) {
pm2xxx_reg_read(pm2,
pm2xxx_interrupt_registers[i],
&(interrupt->reg[i]));
if (interrupt->reg[i] > 0)
interrupt->handler[i](pm2, interrupt->reg[i]);
}
} while (gpio_get_value(pm2->pdata->gpio_irq_number) == 0);
pm_runtime_mark_last_busy(pm2->dev);
pm_runtime_put_autosuspend(pm2->dev);
return IRQ_HANDLED;
}
static int pm2xxx_charger_get_ac_cv(struct pm2xxx_charger *pm2)
{
int ret = 0;
u8 val;
if (pm2->ac.charger_connected && pm2->ac.charger_online) {
ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto out;
}
if (val & PM2XXX_INT4_S_ITCVPHASE)
ret = PM2XXX_CONST_VOLT;
else
ret = PM2XXX_CONST_CURR;
}
out:
return ret;
}
static int pm2xxx_current_to_regval(int curr)
{
int i;
if (curr < pm2xxx_charger_current_map[0])
return 0;
for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_current_map); i++) {
if (curr < pm2xxx_charger_current_map[i])
return (i - 1);
}
i = ARRAY_SIZE(pm2xxx_charger_current_map) - 1;
if (curr == pm2xxx_charger_current_map[i])
return i;
else
return -EINVAL;
}
static int pm2xxx_voltage_to_regval(int curr)
{
int i;
if (curr < pm2xxx_charger_voltage_map[0])
return 0;
for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_voltage_map); i++) {
if (curr < pm2xxx_charger_voltage_map[i])
return i - 1;
}
i = ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1;
if (curr == pm2xxx_charger_voltage_map[i])
return i;
else
return -EINVAL;
}
static int pm2xxx_charger_update_charger_current(struct ux500_charger *charger,
int ich_out)
{
int ret;
int curr_index;
struct pm2xxx_charger *pm2;
u8 val;
if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
pm2 = to_pm2xxx_charger_ac_device_info(charger);
else
return -ENXIO;
curr_index = pm2xxx_current_to_regval(ich_out);
if (curr_index < 0) {
dev_err(pm2->dev,
"Charger current too high, charging not started\n");
return -ENXIO;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
if (ret >= 0) {
val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
val |= curr_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
if (ret < 0) {
dev_err(pm2->dev,
"%s write failed\n", __func__);
}
}
else
dev_err(pm2->dev, "%s read failed\n", __func__);
return ret;
}
static int pm2xxx_charger_ac_get_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
{
struct pm2xxx_charger *pm2;
pm2 = to_pm2xxx_charger_ac_device_info(psy_to_ux500_charger(psy));
switch (psp) {
case POWER_SUPPLY_PROP_HEALTH:
if (pm2->flags.mainextchnotok)
val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
else if (pm2->ac.wd_expired)
val->intval = POWER_SUPPLY_HEALTH_DEAD;
else if (pm2->flags.main_thermal_prot)
val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
else if (pm2->flags.ovv)
val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
else
val->intval = POWER_SUPPLY_HEALTH_GOOD;
break;
case POWER_SUPPLY_PROP_ONLINE:
val->intval = pm2->ac.charger_online;
break;
case POWER_SUPPLY_PROP_PRESENT:
val->intval = pm2->ac.charger_connected;
break;
case POWER_SUPPLY_PROP_VOLTAGE_AVG:
pm2->ac.cv_active = pm2xxx_charger_get_ac_cv(pm2);
val->intval = pm2->ac.cv_active;
break;
default:
return -EINVAL;
}
return 0;
}
static int pm2xxx_charging_init(struct pm2xxx_charger *pm2)
{
int ret = 0;
/* enable CC and CV watchdog */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG3,
(PM2XXX_CH_WD_CV_PHASE_60MIN | PM2XXX_CH_WD_CC_PHASE_60MIN));
if( ret < 0)
return ret;
/* enable precharge watchdog */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG4,
PM2XXX_CH_WD_PRECH_PHASE_60MIN);
/* Disable auto timeout */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG5,
PM2XXX_CH_WD_AUTO_TIMEOUT_20MIN);
/*
* EOC current level = 100mA
* Precharge current level = 100mA
* CC current level = 1000mA
*/
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6,
(PM2XXX_DIR_CH_CC_CURRENT_1000MA |
PM2XXX_CH_PRECH_CURRENT_100MA |
PM2XXX_CH_EOC_CURRENT_100MA));
/*
* recharge threshold = 3.8V
* Precharge to CC threshold = 2.9V
*/
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG7,
(PM2XXX_CH_PRECH_VOL_2_9 | PM2XXX_CH_VRESUME_VOL_3_8));
/* float voltage charger level = 4.2V */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8,
PM2XXX_CH_VOLT_4_2);
/* Voltage drop between VBAT and VSYS in HW charging = 300mV */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG9,
(PM2XXX_CH_150MV_DROP_300MV | PM2XXX_CHARCHING_INFO_DIS |
PM2XXX_CH_CC_REDUCED_CURRENT_IDENT |
PM2XXX_CH_CC_MODEDROP_DIS));
/* Input charger level of over voltage = 10V */
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR2,
PM2XXX_VPWR2_OVV_10);
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR1,
PM2XXX_VPWR1_OVV_10);
/* Input charger drop */
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR2,
(PM2XXX_VPWR2_HW_OPT_DIS | PM2XXX_VPWR2_VALID_DIS |
PM2XXX_VPWR2_DROP_DIS));
ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR1,
(PM2XXX_VPWR1_HW_OPT_DIS | PM2XXX_VPWR1_VALID_DIS |
PM2XXX_VPWR1_DROP_DIS));
/* Disable battery low monitoring */
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_LOW_LEV_COMP_REG,
PM2XXX_VBAT_LOW_MONITORING_ENA);
return ret;
}
static int pm2xxx_charger_ac_en(struct ux500_charger *charger,
int enable, int vset, int iset)
{
int ret;
int volt_index;
int curr_index;
u8 val;
struct pm2xxx_charger *pm2 = to_pm2xxx_charger_ac_device_info(charger);
if (enable) {
if (!pm2->ac.charger_connected) {
dev_dbg(pm2->dev, "AC charger not connected\n");
return -ENXIO;
}
dev_dbg(pm2->dev, "Enable AC: %dmV %dmA\n", vset, iset);
if (!pm2->vddadc_en_ac) {
regulator_enable(pm2->regu);
pm2->vddadc_en_ac = true;
}
ret = pm2xxx_charging_init(pm2);
if (ret < 0) {
dev_err(pm2->dev, "%s charging init failed\n",
__func__);
goto error_occured;
}
volt_index = pm2xxx_voltage_to_regval(vset);
curr_index = pm2xxx_current_to_regval(iset);
if (volt_index < 0 || curr_index < 0) {
dev_err(pm2->dev,
"Charger voltage or current too high, "
"charging not started\n");
return -ENXIO;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG8, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto error_occured;
}
val &= ~PM2XXX_CH_VOLT_MASK;
val |= volt_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
goto error_occured;
}
ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
goto error_occured;
}
val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
val |= curr_index;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
goto error_occured;
}
if (!pm2->bat->enable_overshoot) {
ret = pm2xxx_reg_read(pm2, PM2XXX_LED_CTRL_REG, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n",
__func__);
goto error_occured;
}
val |= PM2XXX_ANTI_OVERSHOOT_EN;
ret = pm2xxx_reg_write(pm2, PM2XXX_LED_CTRL_REG, val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx write failed\n",
__func__);
goto error_occured;
}
}
ret = pm2xxx_charging_enable_mngt(pm2);
if (ret < 0) {
dev_err(pm2->dev, "Failed to enable"
"pm2xxx ac charger\n");
goto error_occured;
}
pm2->ac.charger_online = 1;
} else {
pm2->ac.charger_online = 0;
pm2->ac.wd_expired = false;
/* Disable regulator if enabled */
if (pm2->vddadc_en_ac) {
regulator_disable(pm2->regu);
pm2->vddadc_en_ac = false;
}
ret = pm2xxx_charging_disable_mngt(pm2);
if (ret < 0) {
dev_err(pm2->dev, "failed to disable"
"pm2xxx ac charger\n");
goto error_occured;
}
dev_dbg(pm2->dev, "PM2301: " "Disabled AC charging\n");
}
power_supply_changed(&pm2->ac_chg.psy);
error_occured:
return ret;
}
static int pm2xxx_charger_watchdog_kick(struct ux500_charger *charger)
{
int ret;
struct pm2xxx_charger *pm2;
if (charger->psy.type == POWER_SUPPLY_TYPE_MAINS)
pm2 = to_pm2xxx_charger_ac_device_info(charger);
else
return -ENXIO;
ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_WD_KICK, WD_TIMER);
if (ret)
dev_err(pm2->dev, "Failed to kick WD!\n");
return ret;
}
static void pm2xxx_charger_ac_work(struct work_struct *work)
{
struct pm2xxx_charger *pm2 = container_of(work,
struct pm2xxx_charger, ac_work);
power_supply_changed(&pm2->ac_chg.psy);
sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
};
static void pm2xxx_charger_check_hw_failure_work(struct work_struct *work)
{
u8 reg_value;
struct pm2xxx_charger *pm2 = container_of(work,
struct pm2xxx_charger, check_hw_failure_work.work);
if (pm2->flags.ovv) {
pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4, &reg_value);
if (!(reg_value & (PM2XXX_INT4_S_ITVPWR1OVV |
PM2XXX_INT4_S_ITVPWR2OVV))) {
pm2->flags.ovv = false;
power_supply_changed(&pm2->ac_chg.psy);
}
}
/* If we still have a failure, schedule a new check */
if (pm2->flags.ovv) {
queue_delayed_work(pm2->charger_wq,
&pm2->check_hw_failure_work, round_jiffies(HZ));
}
}
static void pm2xxx_charger_check_main_thermal_prot_work(
struct work_struct *work)
{
int ret;
u8 val;
struct pm2xxx_charger *pm2 = container_of(work, struct pm2xxx_charger,
check_main_thermal_prot_work);
/* Check if die temp warning is still active */
ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT5, &val);
if (ret < 0) {
dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
return;
}
if (val & (PM2XXX_INT5_S_ITTHERMALWARNINGRISE
| PM2XXX_INT5_S_ITTHERMALSHUTDOWNRISE))
pm2->flags.main_thermal_prot = true;
else if (val & (PM2XXX_INT5_S_ITTHERMALWARNINGFALL
| PM2XXX_INT5_S_ITTHERMALSHUTDOWNFALL))
pm2->flags.main_thermal_prot = false;
power_supply_changed(&pm2->ac_chg.psy);
}
static struct pm2xxx_interrupts pm2xxx_int = {
.handler[0] = pm2_int_reg0,
.handler[1] = pm2_int_reg1,
.handler[2] = pm2_int_reg2,
.handler[3] = pm2_int_reg3,
.handler[4] = pm2_int_reg4,
.handler[5] = pm2_int_reg5,
};
static struct pm2xxx_irq pm2xxx_charger_irq[] = {
{"PM2XXX_IRQ_INT", pm2xxx_irq_int},
};
static int pm2xxx_wall_charger_resume(struct i2c_client *i2c_client)
{
struct pm2xxx_charger *pm2;
pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(i2c_client);
set_lpn_pin(pm2);
/* If we still have a HW failure, schedule a new check */
if (pm2->flags.ovv)
queue_delayed_work(pm2->charger_wq,
&pm2->check_hw_failure_work, 0);
return 0;
}
static int pm2xxx_wall_charger_suspend(struct i2c_client *i2c_client,
pm_message_t state)
{
struct pm2xxx_charger *pm2;
pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(i2c_client);
clear_lpn_pin(pm2);
/* Cancel any pending HW failure check */
if (delayed_work_pending(&pm2->check_hw_failure_work))
cancel_delayed_work(&pm2->check_hw_failure_work);
flush_work(&pm2->ac_work);
flush_work(&pm2->check_main_thermal_prot_work);
return 0;
}
#ifdef CONFIG_PM
static int pm2xxx_runtime_suspend(struct device *dev)
{
struct i2c_client *pm2xxx_i2c_client = to_i2c_client(dev);
struct pm2xxx_charger *pm2;
int ret = 0;
pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(pm2xxx_i2c_client);
if (!pm2) {
dev_err(pm2->dev, "no pm2xxx_charger data supplied\n");
ret = -EINVAL;
return ret;
}
clear_lpn_pin(pm2);
return ret;
}
static int pm2xxx_runtime_resume(struct device *dev)
{
struct i2c_client *pm2xxx_i2c_client = to_i2c_client(dev);
struct pm2xxx_charger *pm2;
int ret = 0;
pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(pm2xxx_i2c_client);
if (!pm2) {
dev_err(pm2->dev, "no pm2xxx_charger data supplied\n");
ret = -EINVAL;
return ret;
}
if (gpio_is_valid(pm2->lpn_pin) && gpio_get_value(pm2->lpn_pin) == 0)
set_lpn_pin(pm2);
return ret;
}
static const struct dev_pm_ops pm2xxx_pm_ops = {
.runtime_suspend = pm2xxx_runtime_suspend,
.runtime_resume = pm2xxx_runtime_resume,
};
#define PM2XXX_PM_OPS (&pm2xxx_pm_ops)
#else
#define PM2XXX_PM_OPS NULL
#endif
static int pm2xxx_wall_charger_probe(struct i2c_client *i2c_client,
const struct i2c_device_id *id)
{
struct pm2xxx_platform_data *pl_data = i2c_client->dev.platform_data;
struct pm2xxx_charger *pm2;
int ret = 0;
u8 val;
int i;
pm2 = kzalloc(sizeof(struct pm2xxx_charger), GFP_KERNEL);
if (!pm2) {
dev_err(pm2->dev, "pm2xxx_charger allocation failed\n");
return -ENOMEM;
}
/* get parent data */
pm2->dev = &i2c_client->dev;
pm2->pm2_int = &pm2xxx_int;
/* get charger spcific platform data */
if (!pl_data->wall_charger) {
dev_err(pm2->dev, "no charger platform data supplied\n");
ret = -EINVAL;
goto free_device_info;
}
pm2->pdata = pl_data->wall_charger;
/* get battery specific platform data */
if (!pl_data->battery) {
dev_err(pm2->dev, "no battery platform data supplied\n");
ret = -EINVAL;
goto free_device_info;
}
pm2->bat = pl_data->battery;
if (!i2c_check_functionality(i2c_client->adapter,
I2C_FUNC_SMBUS_BYTE_DATA |
I2C_FUNC_SMBUS_READ_WORD_DATA)) {
ret = -ENODEV;
dev_info(pm2->dev, "pm2301 i2c_check_functionality failed\n");
goto free_device_info;
}
pm2->config.pm2xxx_i2c = i2c_client;
pm2->config.pm2xxx_id = (struct i2c_device_id *) id;
i2c_set_clientdata(i2c_client, pm2);
/* AC supply */
/* power_supply base class */
pm2->ac_chg.psy.name = pm2->pdata->label;
pm2->ac_chg.psy.type = POWER_SUPPLY_TYPE_MAINS;
pm2->ac_chg.psy.properties = pm2xxx_charger_ac_props;
pm2->ac_chg.psy.num_properties = ARRAY_SIZE(pm2xxx_charger_ac_props);
pm2->ac_chg.psy.get_property = pm2xxx_charger_ac_get_property;
pm2->ac_chg.psy.supplied_to = pm2->pdata->supplied_to;
pm2->ac_chg.psy.num_supplicants = pm2->pdata->num_supplicants;
/* pm2xxx_charger sub-class */
pm2->ac_chg.ops.enable = &pm2xxx_charger_ac_en;
pm2->ac_chg.ops.kick_wd = &pm2xxx_charger_watchdog_kick;
pm2->ac_chg.ops.update_curr = &pm2xxx_charger_update_charger_current;
pm2->ac_chg.max_out_volt = pm2xxx_charger_voltage_map[
ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1];
pm2->ac_chg.max_out_curr = pm2xxx_charger_current_map[
ARRAY_SIZE(pm2xxx_charger_current_map) - 1];
pm2->ac_chg.wdt_refresh = WD_KICK_INTERVAL;
pm2->ac_chg.enabled = true;
pm2->ac_chg.external = true;
/* Create a work queue for the charger */
pm2->charger_wq =
create_singlethread_workqueue("pm2xxx_charger_wq");
if (pm2->charger_wq == NULL) {
dev_err(pm2->dev, "failed to create work queue\n");
goto free_device_info;
}
/* Init work for charger detection */
INIT_WORK(&pm2->ac_work, pm2xxx_charger_ac_work);
/* Init work for checking HW status */
INIT_WORK(&pm2->check_main_thermal_prot_work,
pm2xxx_charger_check_main_thermal_prot_work);
/* Init work for HW failure check */
INIT_DEFERRABLE_WORK(&pm2->check_hw_failure_work,
pm2xxx_charger_check_hw_failure_work);
/*
* VDD ADC supply needs to be enabled from this driver when there
* is a charger connected to avoid erroneous BTEMP_HIGH/LOW
* interrupts during charging
*/
pm2->regu = regulator_get(pm2->dev, "vddadc");
if (IS_ERR(pm2->regu)) {
ret = PTR_ERR(pm2->regu);
dev_err(pm2->dev, "failed to get vddadc regulator\n");
goto free_charger_wq;
}
/* Register AC charger class */
ret = power_supply_register(pm2->dev, &pm2->ac_chg.psy);
if (ret) {
dev_err(pm2->dev, "failed to register AC charger\n");
goto free_regulator;
}
/* Register interrupts */
ret = request_threaded_irq(gpio_to_irq(pm2->pdata->gpio_irq_number),
NULL,
pm2xxx_charger_irq[0].isr,
pm2->pdata->irq_type,
pm2xxx_charger_irq[0].name, pm2);
if (ret != 0) {
dev_err(pm2->dev, "failed to request %s IRQ %d: %d\n",
pm2xxx_charger_irq[0].name,
gpio_to_irq(pm2->pdata->gpio_irq_number), ret);
goto unregister_pm2xxx_charger;
}
ret = pm_runtime_set_active(pm2->dev);
if (ret)
dev_err(pm2->dev, "set active Error\n");
pm_runtime_enable(pm2->dev);
pm_runtime_set_autosuspend_delay(pm2->dev, PM2XXX_AUTOSUSPEND_DELAY);
pm_runtime_use_autosuspend(pm2->dev);
pm_runtime_resume(pm2->dev);
/* pm interrupt can wake up system */
ret = enable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
if (ret) {
dev_err(pm2->dev, "failed to set irq wake\n");
goto unregister_pm2xxx_interrupt;
}
mutex_init(&pm2->lock);
if (gpio_is_valid(pm2->pdata->lpn_gpio)) {
/* get lpn GPIO from platform data */
pm2->lpn_pin = pm2->pdata->lpn_gpio;
/*
* Charger detection mechanism requires pulling up the LPN pin
* while i2c communication if Charger is not connected
* LPN pin of PM2301 is GPIO60 of AB9540
*/
ret = gpio_request(pm2->lpn_pin, "pm2301_lpm_gpio");
if (ret < 0) {
dev_err(pm2->dev, "pm2301_lpm_gpio request failed\n");
goto disable_pm2_irq_wake;
}
ret = gpio_direction_output(pm2->lpn_pin, 0);
if (ret < 0) {
dev_err(pm2->dev, "pm2301_lpm_gpio direction failed\n");
goto free_gpio;
}
set_lpn_pin(pm2);
}
/* read interrupt registers */
for (i = 0; i < PM2XXX_NUM_INT_REG; i++)
pm2xxx_reg_read(pm2,
pm2xxx_interrupt_registers[i],
&val);
ret = pm2xxx_charger_detection(pm2, &val);
if ((ret == 0) && val) {
pm2->ac.charger_connected = 1;
ab8500_override_turn_on_stat(~AB8500_POW_KEY_1_ON,
AB8500_MAIN_CH_DET);
pm2->ac_conn = true;
power_supply_changed(&pm2->ac_chg.psy);
sysfs_notify(&pm2->ac_chg.psy.dev->kobj, NULL, "present");
}
return 0;
free_gpio:
if (gpio_is_valid(pm2->lpn_pin))
gpio_free(pm2->lpn_pin);
disable_pm2_irq_wake:
disable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
unregister_pm2xxx_interrupt:
/* disable interrupt */
free_irq(gpio_to_irq(pm2->pdata->gpio_irq_number), pm2);
unregister_pm2xxx_charger:
/* unregister power supply */
power_supply_unregister(&pm2->ac_chg.psy);
free_regulator:
/* disable the regulator */
regulator_put(pm2->regu);
free_charger_wq:
destroy_workqueue(pm2->charger_wq);
free_device_info:
kfree(pm2);
return ret;
}
static int pm2xxx_wall_charger_remove(struct i2c_client *i2c_client)
{
struct pm2xxx_charger *pm2 = i2c_get_clientdata(i2c_client);
/* Disable pm_runtime */
pm_runtime_disable(pm2->dev);
/* Disable AC charging */
pm2xxx_charger_ac_en(&pm2->ac_chg, false, 0, 0);
/* Disable wake by pm interrupt */
disable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
/* Disable interrupts */
free_irq(gpio_to_irq(pm2->pdata->gpio_irq_number), pm2);
/* Delete the work queue */
destroy_workqueue(pm2->charger_wq);
flush_scheduled_work();
/* disable the regulator */
regulator_put(pm2->regu);
power_supply_unregister(&pm2->ac_chg.psy);
if (gpio_is_valid(pm2->lpn_pin))
gpio_free(pm2->lpn_pin);
kfree(pm2);
return 0;
}
static const struct i2c_device_id pm2xxx_id[] = {
{ "pm2301", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, pm2xxx_id);
static struct i2c_driver pm2xxx_charger_driver = {
.probe = pm2xxx_wall_charger_probe,
.remove = pm2xxx_wall_charger_remove,
.suspend = pm2xxx_wall_charger_suspend,
.resume = pm2xxx_wall_charger_resume,
.driver = {
.name = "pm2xxx-wall_charger",
.owner = THIS_MODULE,
.pm = PM2XXX_PM_OPS,
},
.id_table = pm2xxx_id,
};
static int __init pm2xxx_charger_init(void)
{
return i2c_add_driver(&pm2xxx_charger_driver);
}
static void __exit pm2xxx_charger_exit(void)
{
i2c_del_driver(&pm2xxx_charger_driver);
}
device_initcall_sync(pm2xxx_charger_init);
module_exit(pm2xxx_charger_exit);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
MODULE_ALIAS("platform:pm2xxx-charger");
MODULE_DESCRIPTION("PM2xxx charger management driver");