linux-stable/drivers/pwm/pwm-meson.c
Uwe Kleine-König 6c452cff79 pwm: Make .get_state() callback return an error code
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.

This patch was created using coccinelle and the following semantic patch:

@p1@
identifier getstatefunc;
identifier driver;
@@
 struct pwm_ops driver = {
        ...,
        .get_state = getstatefunc
        ,...
 };

@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
 getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
 {
   ...
-  return;
+  return 0;
   ...
 }

plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).

So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.

Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
2022-12-06 12:46:22 +01:00

574 lines
15 KiB
C

// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
/*
* PWM controller driver for Amlogic Meson SoCs.
*
* This PWM is only a set of Gates, Dividers and Counters:
* PWM output is achieved by calculating a clock that permits calculating
* two periods (low and high). The counter then has to be set to switch after
* N cycles for the first half period.
* The hardware has no "polarity" setting. This driver reverses the period
* cycles (the low length is inverted with the high length) for
* PWM_POLARITY_INVERSED. This means that .get_state cannot read the polarity
* from the hardware.
* Setting the duty cycle will disable and re-enable the PWM output.
* Disabling the PWM stops the output immediately (without waiting for the
* current period to complete first).
*
* The public S912 (GXM) datasheet contains some documentation for this PWM
* controller starting on page 543:
* https://dl.khadas.com/Hardware/VIM2/Datasheet/S912_Datasheet_V0.220170314publicversion-Wesion.pdf
* An updated version of this IP block is found in S922X (G12B) SoCs. The
* datasheet contains the description for this IP block revision starting at
* page 1084:
* https://dn.odroid.com/S922X/ODROID-N2/Datasheet/S922X_Public_Datasheet_V0.2.pdf
*
* Copyright (c) 2016 BayLibre, SAS.
* Author: Neil Armstrong <narmstrong@baylibre.com>
* Copyright (C) 2014 Amlogic, Inc.
*/
#include <linux/bitfield.h>
#include <linux/bits.h>
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/math64.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pwm.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#define REG_PWM_A 0x0
#define REG_PWM_B 0x4
#define PWM_LOW_MASK GENMASK(15, 0)
#define PWM_HIGH_MASK GENMASK(31, 16)
#define REG_MISC_AB 0x8
#define MISC_B_CLK_EN BIT(23)
#define MISC_A_CLK_EN BIT(15)
#define MISC_CLK_DIV_MASK 0x7f
#define MISC_B_CLK_DIV_SHIFT 16
#define MISC_A_CLK_DIV_SHIFT 8
#define MISC_B_CLK_SEL_SHIFT 6
#define MISC_A_CLK_SEL_SHIFT 4
#define MISC_CLK_SEL_MASK 0x3
#define MISC_B_EN BIT(1)
#define MISC_A_EN BIT(0)
#define MESON_NUM_PWMS 2
static struct meson_pwm_channel_data {
u8 reg_offset;
u8 clk_sel_shift;
u8 clk_div_shift;
u32 clk_en_mask;
u32 pwm_en_mask;
} meson_pwm_per_channel_data[MESON_NUM_PWMS] = {
{
.reg_offset = REG_PWM_A,
.clk_sel_shift = MISC_A_CLK_SEL_SHIFT,
.clk_div_shift = MISC_A_CLK_DIV_SHIFT,
.clk_en_mask = MISC_A_CLK_EN,
.pwm_en_mask = MISC_A_EN,
},
{
.reg_offset = REG_PWM_B,
.clk_sel_shift = MISC_B_CLK_SEL_SHIFT,
.clk_div_shift = MISC_B_CLK_DIV_SHIFT,
.clk_en_mask = MISC_B_CLK_EN,
.pwm_en_mask = MISC_B_EN,
}
};
struct meson_pwm_channel {
unsigned int hi;
unsigned int lo;
u8 pre_div;
struct clk *clk_parent;
struct clk_mux mux;
struct clk *clk;
};
struct meson_pwm_data {
const char * const *parent_names;
unsigned int num_parents;
};
struct meson_pwm {
struct pwm_chip chip;
const struct meson_pwm_data *data;
struct meson_pwm_channel channels[MESON_NUM_PWMS];
void __iomem *base;
/*
* Protects register (write) access to the REG_MISC_AB register
* that is shared between the two PWMs.
*/
spinlock_t lock;
};
static inline struct meson_pwm *to_meson_pwm(struct pwm_chip *chip)
{
return container_of(chip, struct meson_pwm, chip);
}
static int meson_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct meson_pwm *meson = to_meson_pwm(chip);
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
struct device *dev = chip->dev;
int err;
if (channel->clk_parent) {
err = clk_set_parent(channel->clk, channel->clk_parent);
if (err < 0) {
dev_err(dev, "failed to set parent %s for %s: %d\n",
__clk_get_name(channel->clk_parent),
__clk_get_name(channel->clk), err);
return err;
}
}
err = clk_prepare_enable(channel->clk);
if (err < 0) {
dev_err(dev, "failed to enable clock %s: %d\n",
__clk_get_name(channel->clk), err);
return err;
}
return 0;
}
static void meson_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
{
struct meson_pwm *meson = to_meson_pwm(chip);
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
clk_disable_unprepare(channel->clk);
}
static int meson_pwm_calc(struct meson_pwm *meson, struct pwm_device *pwm,
const struct pwm_state *state)
{
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
unsigned int duty, period, pre_div, cnt, duty_cnt;
unsigned long fin_freq;
duty = state->duty_cycle;
period = state->period;
if (state->polarity == PWM_POLARITY_INVERSED)
duty = period - duty;
fin_freq = clk_get_rate(channel->clk);
if (fin_freq == 0) {
dev_err(meson->chip.dev, "invalid source clock frequency\n");
return -EINVAL;
}
dev_dbg(meson->chip.dev, "fin_freq: %lu Hz\n", fin_freq);
pre_div = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * 0xffffLL);
if (pre_div > MISC_CLK_DIV_MASK) {
dev_err(meson->chip.dev, "unable to get period pre_div\n");
return -EINVAL;
}
cnt = div64_u64(fin_freq * (u64)period, NSEC_PER_SEC * (pre_div + 1));
if (cnt > 0xffff) {
dev_err(meson->chip.dev, "unable to get period cnt\n");
return -EINVAL;
}
dev_dbg(meson->chip.dev, "period=%u pre_div=%u cnt=%u\n", period,
pre_div, cnt);
if (duty == period) {
channel->pre_div = pre_div;
channel->hi = cnt;
channel->lo = 0;
} else if (duty == 0) {
channel->pre_div = pre_div;
channel->hi = 0;
channel->lo = cnt;
} else {
/* Then check is we can have the duty with the same pre_div */
duty_cnt = div64_u64(fin_freq * (u64)duty,
NSEC_PER_SEC * (pre_div + 1));
if (duty_cnt > 0xffff) {
dev_err(meson->chip.dev, "unable to get duty cycle\n");
return -EINVAL;
}
dev_dbg(meson->chip.dev, "duty=%u pre_div=%u duty_cnt=%u\n",
duty, pre_div, duty_cnt);
channel->pre_div = pre_div;
channel->hi = duty_cnt;
channel->lo = cnt - duty_cnt;
}
return 0;
}
static void meson_pwm_enable(struct meson_pwm *meson, struct pwm_device *pwm)
{
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
struct meson_pwm_channel_data *channel_data;
unsigned long flags;
u32 value;
channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
spin_lock_irqsave(&meson->lock, flags);
value = readl(meson->base + REG_MISC_AB);
value &= ~(MISC_CLK_DIV_MASK << channel_data->clk_div_shift);
value |= channel->pre_div << channel_data->clk_div_shift;
value |= channel_data->clk_en_mask;
writel(value, meson->base + REG_MISC_AB);
value = FIELD_PREP(PWM_HIGH_MASK, channel->hi) |
FIELD_PREP(PWM_LOW_MASK, channel->lo);
writel(value, meson->base + channel_data->reg_offset);
value = readl(meson->base + REG_MISC_AB);
value |= channel_data->pwm_en_mask;
writel(value, meson->base + REG_MISC_AB);
spin_unlock_irqrestore(&meson->lock, flags);
}
static void meson_pwm_disable(struct meson_pwm *meson, struct pwm_device *pwm)
{
unsigned long flags;
u32 value;
spin_lock_irqsave(&meson->lock, flags);
value = readl(meson->base + REG_MISC_AB);
value &= ~meson_pwm_per_channel_data[pwm->hwpwm].pwm_en_mask;
writel(value, meson->base + REG_MISC_AB);
spin_unlock_irqrestore(&meson->lock, flags);
}
static int meson_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
const struct pwm_state *state)
{
struct meson_pwm *meson = to_meson_pwm(chip);
struct meson_pwm_channel *channel = &meson->channels[pwm->hwpwm];
int err = 0;
if (!state->enabled) {
if (state->polarity == PWM_POLARITY_INVERSED) {
/*
* This IP block revision doesn't have an "always high"
* setting which we can use for "inverted disabled".
* Instead we achieve this using the same settings
* that we use a pre_div of 0 (to get the shortest
* possible duration for one "count") and
* "period == duty_cycle". This results in a signal
* which is LOW for one "count", while being HIGH for
* the rest of the (so the signal is HIGH for slightly
* less than 100% of the period, but this is the best
* we can achieve).
*/
channel->pre_div = 0;
channel->hi = ~0;
channel->lo = 0;
meson_pwm_enable(meson, pwm);
} else {
meson_pwm_disable(meson, pwm);
}
} else {
err = meson_pwm_calc(meson, pwm, state);
if (err < 0)
return err;
meson_pwm_enable(meson, pwm);
}
return 0;
}
static unsigned int meson_pwm_cnt_to_ns(struct pwm_chip *chip,
struct pwm_device *pwm, u32 cnt)
{
struct meson_pwm *meson = to_meson_pwm(chip);
struct meson_pwm_channel *channel;
unsigned long fin_freq;
u32 fin_ns;
/* to_meson_pwm() can only be used after .get_state() is called */
channel = &meson->channels[pwm->hwpwm];
fin_freq = clk_get_rate(channel->clk);
if (fin_freq == 0)
return 0;
fin_ns = div_u64(NSEC_PER_SEC, fin_freq);
return cnt * fin_ns * (channel->pre_div + 1);
}
static int meson_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
struct pwm_state *state)
{
struct meson_pwm *meson = to_meson_pwm(chip);
struct meson_pwm_channel_data *channel_data;
struct meson_pwm_channel *channel;
u32 value, tmp;
if (!state)
return 0;
channel = &meson->channels[pwm->hwpwm];
channel_data = &meson_pwm_per_channel_data[pwm->hwpwm];
value = readl(meson->base + REG_MISC_AB);
tmp = channel_data->pwm_en_mask | channel_data->clk_en_mask;
state->enabled = (value & tmp) == tmp;
tmp = value >> channel_data->clk_div_shift;
channel->pre_div = FIELD_GET(MISC_CLK_DIV_MASK, tmp);
value = readl(meson->base + channel_data->reg_offset);
channel->lo = FIELD_GET(PWM_LOW_MASK, value);
channel->hi = FIELD_GET(PWM_HIGH_MASK, value);
if (channel->lo == 0) {
state->period = meson_pwm_cnt_to_ns(chip, pwm, channel->hi);
state->duty_cycle = state->period;
} else if (channel->lo >= channel->hi) {
state->period = meson_pwm_cnt_to_ns(chip, pwm,
channel->lo + channel->hi);
state->duty_cycle = meson_pwm_cnt_to_ns(chip, pwm,
channel->hi);
} else {
state->period = 0;
state->duty_cycle = 0;
}
return 0;
}
static const struct pwm_ops meson_pwm_ops = {
.request = meson_pwm_request,
.free = meson_pwm_free,
.apply = meson_pwm_apply,
.get_state = meson_pwm_get_state,
.owner = THIS_MODULE,
};
static const char * const pwm_meson8b_parent_names[] = {
"xtal", "vid_pll", "fclk_div4", "fclk_div3"
};
static const struct meson_pwm_data pwm_meson8b_data = {
.parent_names = pwm_meson8b_parent_names,
.num_parents = ARRAY_SIZE(pwm_meson8b_parent_names),
};
static const char * const pwm_gxbb_parent_names[] = {
"xtal", "hdmi_pll", "fclk_div4", "fclk_div3"
};
static const struct meson_pwm_data pwm_gxbb_data = {
.parent_names = pwm_gxbb_parent_names,
.num_parents = ARRAY_SIZE(pwm_gxbb_parent_names),
};
/*
* Only the 2 first inputs of the GXBB AO PWMs are valid
* The last 2 are grounded
*/
static const char * const pwm_gxbb_ao_parent_names[] = {
"xtal", "clk81"
};
static const struct meson_pwm_data pwm_gxbb_ao_data = {
.parent_names = pwm_gxbb_ao_parent_names,
.num_parents = ARRAY_SIZE(pwm_gxbb_ao_parent_names),
};
static const char * const pwm_axg_ee_parent_names[] = {
"xtal", "fclk_div5", "fclk_div4", "fclk_div3"
};
static const struct meson_pwm_data pwm_axg_ee_data = {
.parent_names = pwm_axg_ee_parent_names,
.num_parents = ARRAY_SIZE(pwm_axg_ee_parent_names),
};
static const char * const pwm_axg_ao_parent_names[] = {
"aoclk81", "xtal", "fclk_div4", "fclk_div5"
};
static const struct meson_pwm_data pwm_axg_ao_data = {
.parent_names = pwm_axg_ao_parent_names,
.num_parents = ARRAY_SIZE(pwm_axg_ao_parent_names),
};
static const char * const pwm_g12a_ao_ab_parent_names[] = {
"xtal", "aoclk81", "fclk_div4", "fclk_div5"
};
static const struct meson_pwm_data pwm_g12a_ao_ab_data = {
.parent_names = pwm_g12a_ao_ab_parent_names,
.num_parents = ARRAY_SIZE(pwm_g12a_ao_ab_parent_names),
};
static const char * const pwm_g12a_ao_cd_parent_names[] = {
"xtal", "aoclk81",
};
static const struct meson_pwm_data pwm_g12a_ao_cd_data = {
.parent_names = pwm_g12a_ao_cd_parent_names,
.num_parents = ARRAY_SIZE(pwm_g12a_ao_cd_parent_names),
};
static const char * const pwm_g12a_ee_parent_names[] = {
"xtal", "hdmi_pll", "fclk_div4", "fclk_div3"
};
static const struct meson_pwm_data pwm_g12a_ee_data = {
.parent_names = pwm_g12a_ee_parent_names,
.num_parents = ARRAY_SIZE(pwm_g12a_ee_parent_names),
};
static const struct of_device_id meson_pwm_matches[] = {
{
.compatible = "amlogic,meson8b-pwm",
.data = &pwm_meson8b_data
},
{
.compatible = "amlogic,meson-gxbb-pwm",
.data = &pwm_gxbb_data
},
{
.compatible = "amlogic,meson-gxbb-ao-pwm",
.data = &pwm_gxbb_ao_data
},
{
.compatible = "amlogic,meson-axg-ee-pwm",
.data = &pwm_axg_ee_data
},
{
.compatible = "amlogic,meson-axg-ao-pwm",
.data = &pwm_axg_ao_data
},
{
.compatible = "amlogic,meson-g12a-ee-pwm",
.data = &pwm_g12a_ee_data
},
{
.compatible = "amlogic,meson-g12a-ao-pwm-ab",
.data = &pwm_g12a_ao_ab_data
},
{
.compatible = "amlogic,meson-g12a-ao-pwm-cd",
.data = &pwm_g12a_ao_cd_data
},
{},
};
MODULE_DEVICE_TABLE(of, meson_pwm_matches);
static int meson_pwm_init_channels(struct meson_pwm *meson)
{
struct device *dev = meson->chip.dev;
struct clk_init_data init;
unsigned int i;
char name[255];
int err;
for (i = 0; i < meson->chip.npwm; i++) {
struct meson_pwm_channel *channel = &meson->channels[i];
snprintf(name, sizeof(name), "%s#mux%u", dev_name(dev), i);
init.name = name;
init.ops = &clk_mux_ops;
init.flags = 0;
init.parent_names = meson->data->parent_names;
init.num_parents = meson->data->num_parents;
channel->mux.reg = meson->base + REG_MISC_AB;
channel->mux.shift =
meson_pwm_per_channel_data[i].clk_sel_shift;
channel->mux.mask = MISC_CLK_SEL_MASK;
channel->mux.flags = 0;
channel->mux.lock = &meson->lock;
channel->mux.table = NULL;
channel->mux.hw.init = &init;
channel->clk = devm_clk_register(dev, &channel->mux.hw);
if (IS_ERR(channel->clk)) {
err = PTR_ERR(channel->clk);
dev_err(dev, "failed to register %s: %d\n", name, err);
return err;
}
snprintf(name, sizeof(name), "clkin%u", i);
channel->clk_parent = devm_clk_get_optional(dev, name);
if (IS_ERR(channel->clk_parent))
return PTR_ERR(channel->clk_parent);
}
return 0;
}
static int meson_pwm_probe(struct platform_device *pdev)
{
struct meson_pwm *meson;
int err;
meson = devm_kzalloc(&pdev->dev, sizeof(*meson), GFP_KERNEL);
if (!meson)
return -ENOMEM;
meson->base = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(meson->base))
return PTR_ERR(meson->base);
spin_lock_init(&meson->lock);
meson->chip.dev = &pdev->dev;
meson->chip.ops = &meson_pwm_ops;
meson->chip.npwm = MESON_NUM_PWMS;
meson->data = of_device_get_match_data(&pdev->dev);
err = meson_pwm_init_channels(meson);
if (err < 0)
return err;
err = devm_pwmchip_add(&pdev->dev, &meson->chip);
if (err < 0) {
dev_err(&pdev->dev, "failed to register PWM chip: %d\n", err);
return err;
}
return 0;
}
static struct platform_driver meson_pwm_driver = {
.driver = {
.name = "meson-pwm",
.of_match_table = meson_pwm_matches,
},
.probe = meson_pwm_probe,
};
module_platform_driver(meson_pwm_driver);
MODULE_DESCRIPTION("Amlogic Meson PWM Generator driver");
MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
MODULE_LICENSE("Dual BSD/GPL");