Add the descriptions of the “core”, that means no vendorcode or payload,
coreboot time stamps added up to coreboot commit a7d92441 (timestamps:
You can never have enough of them!) [1].
Running `coreboot_boottime` in the GRUB command line interface now shows
descriptions for all time stamps again on the ASRock E350M1.
[1] http://review.coreboot.org/9608
From RFC1542:
The 'giaddr' field is rather poorly named. It exists to facilitate
the transfer of BOOTREQUEST messages from a client, through BOOTP
relay agents, to servers on different networks than the client.
Similarly, it facilitates the delivery of BOOTREPLY messages from the
servers, through BOOTP relay agents, back to the client. In no case
does it represent a general IP router to be used by the client. A
BOOTP client MUST set the 'giaddr' field to zero (0.0.0.0) in all
BOOTREQUEST messages it generates.
A BOOTP client MUST NOT interpret the 'giaddr' field of a BOOTREPLY
message to be the IP address of an IP router. A BOOTP client SHOULD
completely ignore the contents of the 'giaddr' field in BOOTREPLY
messages.
Leave code ifdef'd out for the time being in case we see regression.
Suggested by: Rink Springer <rink@rink.nu>
Closes: 43396
Currently XFS driver converted inode numbers to native endianity only
when using them to compute inode position. Although this works, it is
somewhat confusing. So convert inode numbers when reading them from disk
structures as every other field.
Signed-off-by: Jan Kara <jack@suse.cz>
Directory iteration used wrong position (sizeof wrong structure) for
termination of iteration inside a directory block. Luckily the position
ended up being wrong by just 1 byte and directory entries are larger so
things worked out fine in practice. But fix the problem anyway.
Signed-off-by: Jan Kara <jack@suse.cz>
EBDA layout is not standardized so we cannot assume first two bytes
are length. Neither is it required by ACPI standard. HP 8710W is known
to contain zeroes here.
Closes: 45002
EDK2 network stack is based on Managed Network Protocol which is layered
on top of Simple Management Protocol and does background polling. This
polling races with grub for received (and probably trasmitted) packets
which causes either serious slowdown or complete failure to load files.
Open SNP device exclusively. This destroys all child MNP instances and
stops background polling.
Exclusive open cannot be done when enumerating cards, as it would destroy
PXE information we need to autoconfigure interface; and it cannot be done
during autoconfiguration as we need to do it for non-PXE boot as well. So
move SNP open to card ->open method and add matching ->close to clean up.
Based on patch from Mark Salter <msalter@redhat.com>
Also-By: Mark Salter <msalter@redhat.com>
Closes: 41731
EDK2 PXE driver creates two child devices - IPv4 and IPv6 - with
bound SNP instance. This means we get three cards for every physical
adapter when enumerating. Not only is this confusing, this may result
in grub ignoring packets that come in via the "wrong" card.
Example of device hierarchy is
Ctrl[91] PciRoot(0x0)/Pci(0x3,0x0)
Ctrl[95] PciRoot(0x0)/Pci(0x3,0x0)/MAC(525400123456,0x1)
Ctrl[B4] PciRoot(0x0)/Pci(0x3,0x0)/MAC(525400123456,0x1)/IPv4(0.0.0.0)
Ctrl[BC] PciRoot(0x0)/Pci(0x3,0x0)/MAC(525400123456,0x1)/IPv6(0000:0000:0000:0000:0000:0000:0000:0000)
Skip PXE created virtual devices when enumerating cards. Make sure to
find real card when applying initial autoconfiguration during PXE boot,
this information is associated with one of child devices.
Syslinux memdisk is using initrd image and needs to know uncompressed
size in advance. For gzip uncompressed size is at the end of compressed
stream. Grub padded each input file to 4 bytes at the end, which means
syslinux got wrong size.
Linux initramfs loader apparently does not care about trailing alignment.
So change code to align beginning of each file instead which atomatically
gives us the correct size for single file.
Reported-By: David Shaw <dshaw@jabberwocky.com>
This reverts commits 47b2bee3ef
and 8d3c4544ff. It is not safe
to free allocated cards, dangling pointers main remain. Such
cleanup requires more changes in net core.
grub_memset should zero out padding after data end. It is not clear
why it is needed at all - ZFS block is at least 512 bytes and power
of two, so it is always multiple of 16 bytes. This grub_memset
apparently never did anything.
In the past birth was always zero for holes. This feature started
to make use of birth for holes as well, so change code to test for
valid DVA address instead.
It can be called with NULL for third argument. grub_divmod32* for
now are called only from within wrappers, so skip check.
Reported-By: Michael Zimmermann <sigmaepsilon92@gmail.com>
Some x86 systems might be capable of running a 64-bit Linux kernel but
only use a 32-bit EFI (e.g. Intel Bay Trail systems). It's useful for
grub-install to be able to recognise such systems, to set the default
x86 platform correctly.
To allow grub-install to know the size of the firmware rather than
just the size of the kernel, there is now an extra EFI sysfs file to
describe the underlying firmware. Read that if possible, otherwise
fall back to the kernel type as before.
Signed-off-by: Steve McIntyre <steve@einval.com>
Use the new thumb_get_instruction_word/thumb_set_instruction_word
helpers throughout.
Style cleanup (missing spaces).
Move Thumb MOVW/MOVT handlers into Thumb relocation section of file.
This restrict ARP handling to MAC and IP addresses but in practice we need
only this case anyway and other cases are very rar if exist at all. It makes
code much simpler and less error-prone.
_BSD_SOURCE was added to allow the use of DT_DIR, but that was removed
in e768b77068. While adding
_DEFAULT_SOURCE as well works around problems with current glibc,
neither is in fact needed nowadays.
