send client arch in bootp requests, for now BIOS and x64/aarch64 EFI is
supported.
fix a bug introduced in 4d5d7be005 where
user class was encoded improperly, although this didn't seem to have any
detrimental effects.
properly insert an option terminator.
If we open new connection, we need to reset stall indication, otherwise
nothing will ever be polled (low level code rely on this field being
zero when establishing connection).
Depending on the OS/libc, device macros are defined in different
headers. This change ensures we include the right one.
sys/types.h - BSD
sys/mkdev.h - Sun
sys/sysmacros.h - glibc (Linux)
glibc currently pulls sys/sysmacros.h into sys/types.h, but this may
change in a future release.
https://sourceware.org/ml/libc-alpha/2015-11/msg00253.html
At least the apache sever is very unhappy with that extra null line and will
take more than ten seconds in responding to each range request, which slows
down a lot the entire http file transfer process or even time out.
Some DHCP servers (such as dnsmasq) tokenise parameters with commas, making
it impossible to pass boot files with commas in them. Allow using a semicolon
to separate the protocol from host if a comma wasn't found.
The current logic in the DNS resolution code allocates an address buffer
based on the number of addresses in the response packet. If we receive
multiple response packets in response to a single query packet, this means
that we will reallocate a new buffer large enough for only the addresses in
that specific packet, discarding any previous results in the process. Worse,
we still keep track of the *total* number of addresses resolved in response
to this query, not merely the number in the packet being currently processed.
Use realloc() rather than malloc() to avoid overwriting the existing data,
and allocate a buffer large enough for the total set of addresses rather
than merely the number in this specific response.
Rework TPM measurements to use fewer PCRs. After discussion with upstream,
it's preferable to avoid using so many PCRs. Instead, measure into PCRs 8
and 9 but use a prefix in the event log to indicate which subsystem carried
out the measurements.
OpenBSD 5.9 apparently defaults to -fpie. We use -fno-PIE when appropriate
already, but that is not enough - it does not turn off -fpie.
Actually check for -fPIE is not precise enough. __PIE__ is set for both
-fpie and -fPIE but with different values. As far as I can tell, both
options were introduced at the same time, so both should always be supported.
This fixes compilation on OpenBSD 5.9 which otherwise created insanely big
lzma_decompress.img.
Reported, suggested and tested by: Jiri B <jirib@devio.us>
Historically this variable hold previous value of filename that
had to be freed if allocated previously. Currently this branch
is entered only if filename was not allocated previously so it
became redundant. It did not cause real problems because grub_free
was not called, but code is confusing and causes compilation error
in some cases.
Grub would notify the user if the new config was invalid, however, it
did not exit properly with exit code 1. Added the proper exit code.
Resolves: rhbz#1252311
Returned from the OpenProtocol operation, the grub_efi_block_io_media
structure contains the io_align field, specifying the minimum alignment
required for buffers used in any data transfers with the device.
Make grub_efidisk_readwrite() allocate a temporary buffer, aligned to
this boundary, if the buffer passed to it does not already meet the
requirements.
Also sanity check the io_align field in grub_efidisk_open() for
power-of-two-ness and bail if invalid.
util/grub-mkimagexx.c is included in a special way into mkimage.c.
Interoperation between defines makes this very tricky. Instead
just have a clean interface and compile util/grub-mkimage*.c separately
from mkimage.c
Map EFI_NO_MEDIA to GRUB_ERR_OUT_OF_RANGE that is ignored by diskfilter. This
actually matches pretty close (we obviously attempt to read outside of media)
and avoids adding more error codes.
This affects only internally initiated scans. If read/write from removable is
explicitly requested, we still return an error and text explanation is more
clear for user than generic error.
Reported and tested by Andreas Loew <Andreas.Loew@gmx.net>
ipv6 routing in grub2 is broken, we cannot talk to anything outside our local
network or anything that doesn't route in our global namespace. This patch
fixes this by doing a couple of things
1) Read the router information off of the router advertisement. If we have a
router lifetime we need to take the source address and create a route from it.
2) Changes the routing stuff slightly to allow you to specify a gateway _and_ an
interface. Since the router advertisements come in on the link local address we
need to associate it with the global address on the card. So when we are
processing the router advertisement, either use the SLAAC interface we create
and add the route to that interface, or loop through the global addresses we
currently have on our interface and associate it with one of those addresses.
We need to have a special case here for the default route so that it gets used,
we do this by setting the masksize to 0 to mean it encompasses all networks.
The routing code will automatically select the best route so if there is a
closer match we will use that.
With this patch I can now talk to ipv6 addresses outside of my local network.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
